Page 1
Mobile DVR
User Manual
Page 2
Mobile Digital Video Recorder User Manual
2
TABLE OF CONTENTS
Chapter 1 Panel Introduction ...............................................................................................................................................................8
1.1 Front Panel .................................................................................................................................................................................8
1.2 Rear Panel ..................................................................................................................................................................................9
Chapter 2 Installation and Connections ............................................................................................................................................ 10
2.1 Install SIM Card ...................................................................................................................................................................... 10
2.2 Install SD Card ........................................................................................................................................................................ 12
2.3 Power Cord Wiring .................................................................................................................................................................. 12
2.3.1 Shutdown Delay ............................................................................................................................................................ 12
2.3.2 Scheduled Shutdown ..................................................................................................................................................... 14
2.4 Alarm Input/Output Connection .............................................................................................................................................. 15
2.4.1 Alarm Input Connection ................................................................................................................................................ 15
2.4.2 Alarm Output Connection ............................................................................................................................................. 15
2.5 Sensor-in Wiring ...................................................................................................................................................................... 16
2.6 Power-on .................................................................................................................................................................................. 16
Page 3
Mobile Digital Video Recorder User Manual
3
User Manual
COPYRIGHT © 2018 Hangzhou Hikvision Digital Technology Co., Ltd.
ALL RIGHTS RESERVED.
Any and all information, including, among others, wordings, pictures, graphs are the properties of
Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be
“Hikvision”). This user manual (hereinafter referred to be “the Manual”) cannot be reproduced,
changed, translated, or distributed, partially or wholly, by any means, without the prior written
permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties,
guarantees or representations, express or implied, regarding to the Manual.
About this Manual
This Manual is applicable to Mobile Digital Video Recorder (MDVR).
The Manual includes instructions for using and managing the product. Pictures, charts, images and
all other information hereinafter are for description and explanation only. The information
contained in the Manual is subject to change, without notice, due to firmware updates or other
reasons. Please find the latest version in the company website
(http://overseas.hikvision.com/en/).
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are the properties of Hikvision in various
jurisdictions. Other trademarks and logos mentioned below are the properties of their respective
owners.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS
HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS,
AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,
MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND
NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS,
EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR
INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS,
BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE
USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY
AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL
OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER
ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL
PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR
JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS
THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS
USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER
PREVAILS.
Page 4
Mobile Digital Video Recorder User Manual
4
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
Note: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the
applicable harmonized European standards listed under the RE Directive 2014/53/EU, the EMC Directive 2014/30/ EU,
and the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in
the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info
2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal
waste in the European Union. See the product documentation for specific battery information. The battery is marked
with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper
recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est
Page 5
Mobile Digital Video Recorder User Manual
5
autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'e n
compromettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and
its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le
but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son
gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une
communication satisfaisante.
This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body.
Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et votre corps.
Page 6
Mobile Digital Video Recorder User Manual
6
Applicable Models
This manual is applicable to DS-MP3504-SD series MDVR.
Symbol Conventions
The symbols that may be found in this document are defined as follows.
Symbol
Description
Provides additional information to emphasize or supplement
important points of the main text.
Indicates a potentially hazardous situation, which if not avoided,
could result in equipment damage, data loss, performance
degradation, or unexpected results.
Indicates a hazard with a high level of risk, which if not avoided, will
result in death or serious injury.
Page 7
Mobile Digital Video Recorder User Manual
7
Safety Instructions
Proper configuration of all passwords and other security settings is the responsibility of the
installer and/or end-user.
In the use of the product, you must be in strict compliance with the electrical safety
regulations of the nation and region. Please refer to technical specifications for detailed
information.
Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power
Source with 9 to 32 VDC according to the IEC60950-1 standard. Please refer to technical
specifications for detailed information.
Do not connect several devices to one power adapter as adapter overload may cause
over-heating or a fire hazard.
Please make sure that the plug is firmly connected to the power socket.
If smoke, odor or noise rise from the device, turn off the power at once and unplug the power
cable, and then please contact the service center.
Preventive and Cautionary Tips
Before connecting and operating your device, please be advised of the following tips:
Ensure unit is installed in a well-ventilated, dust-free environment.
Keep all liquids away from the device.
Ensure environmental conditions meet factory specifications.
Ensure unit is properly secured to a rack or shelf. Major shocks or jolts to the unit as a result of
dropping it may cause damage to the sensitive electronics within the unit.
Use the device in conjunction with an UPS if possible.
Power down the unit before connecting and disconnecting accessories and peripherals.
Improper use or replacement of the battery may result in hazard of explosion. Replace with
the same or equivalent type only. Dispose of used batteries according to the instructions
provided by the battery manufacturer.
Page 8
Mobile Digital Video Recorder User Manual
8
Chapter 1 Panel Introduction
1.1 Front Panel
1
3
5
2
4
6
Figure 1-1 Front Panel
Table 1-1 Interface Description
No.
Name
Description
1
SD1&SD2
Two SD card slots.
2
OFF/ON
Power switch.
3
POWER
Power indicator: Light in green after device starts up; light in
red when standby mode.
4
RECORD
Record indicator: Light in green during recording process.
5
IR
IR Receiver: Receive IR signal from remote control.
6
USB
USB interface.
Page 9
Mobile Digital Video Recorder User Manual
9
1.2 Rear Panel
8
9
2
4
7
1 3 5
6
Figure 1-2 Rear Panel
Table 1-2 Interface Description
No.
Name
Description
1
M-ANT
Reserved.
2
GNSS
Reserved.
3
WIFI
Reserved.
4
RS-232
RS-232 interface.
5
EXT.DEV
RS-422 communication interface, two-way audio, CVBS video
output.
6
I/O
7-ch high / low level signal trigger including 3-ch alarm inputs,
4-ch sensor in; 1-ch pulse signal input.
7
LAN
10M/100M self-adaptive Ethernet interface
8
CH1~CH4
4-pin aviation plug, audio & video input of channel 1~4.
9
POWER
6-pin aviation plug for power supply and start control.
Page 10
Mobile Digital Video Recorder User Manual
10
Chapter 2 Installation and Connections
Product pictures in following chapters are for reference only. In the event of any conflicts between
this manual and the product, the later prevails.
2.1 Install SIM Card
Purpose:
Pluggable 3G/4G wireless communication module is designed for the device and you should install
the SIM card to realize the wireless communication function.
The chapter is only available for device with 3G/4G module.
Before You Start
Prepare the tools and components for installation:
SIM card
Wrench
Figure 2-1 Tools
Step 1 Use wrench to unfasten and remove the two screws fixing the 3G/4G and Wi-Fi module.
Step 2 Pull out the 3G/4G and Wi-Fi module.
Step 3 Press the yellow button on the 3G/4G slot and then pull the SIM card tray out.
Page 11
Mobile Digital Video Recorder User Manual
11
Figure 2-2 Pull out SIM Card Tray
Step 4 Place the SIM card on SIM card tray.
Figure 2-3 Place SIM card on SIM Card Tray
Step 5 Insert the SIM card tray back to SIM card slot.
Figure 2-4 Insert SIM Card Tray back to SIM Card Slot
Page 12
Mobile Digital Video Recorder User Manual
12
Step 6 Install the 3G/4G module back to the device and tighten the set screw.
2.2 Install SD Card
Before You Start
Prepare the tools and components for installation:
Key to front panel (delivered with device)
SD card. Use the factory recommended SD card, thus to ensure data security.
Figure 2-5 Tools
Step 1 Shut down the device before plugging in or removing SD card.
Step 2 Insert the key and turn clockwise to unlock front panel.
Step 3 Insert SD card into SD card slot till you hear a click.
Step 4 Repeat step 3 to install the other SD card.
Step 5 Turn the key to lock front panel.
2.3 Power Cord Wiring
In order to ensure the safety of your automobile and device, a fuse is required for wiring of
automobile power and device power.
Do not connect the power cord to the device before all the cables are connected.
2.3.1 Shutdown Delay
Purpose:
The device starts up when your automobile ignites and shuts down after automobile is off.
Automobile ignition startup and shutdown are realized by automobile positive pole ignition switch
(providing high level signal when the switch closes). The wire connection of the device varies with
the automobile ignition models.
Ignition switch is connected to the positive pole of +12/24 VDC of automobile batteries. Make sure
that the connection is correct, and then perform the following steps:
Page 13
Mobile Digital Video Recorder User Manual
13
Step 1 Connect the "DC IN +" of the device to the positive pole of automobile batteries, jumping
over the switch of normal automobile power.
Step 2 Connect the "DC IN -" of the device to the negative pole of automobile batteries.
Step 3 Connect the "ACC" of the device to the automobile ignition switch.
Step 4 Place the fuse into the fuse holder.
What to do next: For detailed time settings of time-delay shutdown, see Chapter Configure
Delayed Shutdown in user manual.
Figure 2-6 Install Fuse for Two Types of Power Supply
ACC
DC IN
+
-
Automobile Ignition Switch
Device
Automobile
Battery
Automobile Power System
Wiring of Device
Point of Connection
Positive Pole
Negative Pole
Automobile Power Switch
Figure 2-7 Shutdown Delay
Page 14
Mobile Digital Video Recorder User Manual
14
Please contact the automobile manufacturer for the connection information of starting
switch.
The automobile ignition switch, also called car key, controls the startup and shutdown of
your automobile. Most of automobiles adopt positive pole ignition switch currently.
The normal automobile power refers to the main power of the automobile power supply
system. After the automobile is off, the normal automobile power still provides
direct-current source for the other devices inside and generally a main switch is used to
turn on/off it.
2.3.2 Scheduled Shutdown
Step 1 Connect the “DC IN +” and “KEY +” of the device to the positive pole of automobile batteries.
Step 2 Connect the “DC IN -” and “KEY -” of the device to the negative pole of automobile batteries.
Step 3 Place the fuse into the fuse holder.
What to do next: For detailed time settings of time-delay shutdown, see Chapter Enable Scheduled
Startup/Shutdown in user manual.
Figure 2-8 Install Fuse for Two Types of Power Supply
Page 15
Mobile Digital Video Recorder User Manual
15
ACC
DC IN
+
-
Device
Automobile
Battery
Automobile Power Switch
Automobile Power System
Wiring of Device
Point of Connection
Negative Pole
Positive Pole
Figure 2-9 Scheduled Shutdown
2.4 Alarm Input/Output Connection
2.4.1 Alarm Input Connection
The device adopts the high/low-level electrical signals triggering (high level: 6 to 36 VDC; low level:
0 to 5 VDC) to realize alarm input. And in order to avoid error report caused by voltage fluctuation,
no alarm will be triggered by voltage ranging of 5 to 6 VDC.
Alarm 1
IO
Alarm 2
Alarm 3
Alarm 4
1
2
15
16
Figure 2-10 Alarm Input Connection
The number of alarm input varies with device model.
2.4.2 Alarm Output Connection
Follow the figure bellow to wire alarm output.
n and n# are a pair of alarm output. You can connect them with a relay alarm device. When the
voltage of connected alarm device exceeds the valid alarm output range, you need to connect a
relay to protect alarm output.
Page 16
Mobile Digital Video Recorder User Manual
16
Relay
Output
n
n#
Load
GND
Power
Output
JQC-3FG
Relay
(10 A/250 VAC)
~ 220 VAC
NeutralLive
Relay
Output
n#
n
Alarm Powered by Direct Current Alarm Powered by Alternating Current
Figure 2-11 Alarm Output Connection
2.5 Sensor-in Wiring
Step 1 Connect the delivered extension cable to I/O interface.
Step 2 Connect the automobile braking, reversing, left-turn, and right-turn signals to sensor-in
interface.
IO
Braking
Reversing
1
2
15
16
Left-turn
Right-turn
Figure 2-12 Sensor-in Wiring
2.6 Power-on
Turn on the power supply after all the above installations are finished.
You can view the indicators to get knowledge about the device status. For details, refer to Table
1-1.
Page 17
Mobile Digital Video Recorder User Manual
17
UD10195B
Loading...