HIKVISION DS-KV8102-VP, DS-KV8102-IP User Manual
UD06175B
Video Intercom Door Station
(V Series)
User Manual
Video Intercom Door Station·User Manual
i
User Manual
© 2017 Hangzhou Hikvision Digital Technology Co., Ltd.
This user manual is intended for users of the models below:
Series
Model
Door Station (V Series)
DS-KV8102-IM
DS-KV8202-IM
DS-KV8402-IM
DS-KV8102-IP
DS-KV8102-VP
It includes instructions on how to use the Product. The software embodied in the
Product is governed by the user license agreement covering that product.
About this Manual
This Manual is subject to domestic and international copyright protection. Hangzhou
Hikvision Digital Technology Co., Ltd. (“Hikvision”) reserves all rights to this manual. This
manual cannot be reproduced, changed, translated, or distributed, partially or wholly, by
any means, without the prior written permission of Hikvision.
Trademarks
and other Hikvision marks are the property of Hikvision and are
registered trademarks or the subject of applications for the same by Hikvision and/or its
affiliates. Other trademarks mentioned in this manual are the properties of their
respective owners. No right of license is given to use such trademarks without express
permission.
Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, HIKVISION MAKES NO WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICUL AR PURPOSE, REGARDING THIS MANUAL.
HIKVISION DOES NOT WARRANT, GUARANTEE, OR MAKE ANY REPRESENTATIONS REGARDING THE
USE OF THE MANUAL, OR THE CORRECTNESS, ACCURACY, OR RELIABILITY OF INFORMATION
CONTAINED HEREIN. YOUR USE OF THIS MANUAL AND ANY RELIANCE ON THIS MANUAL SHALL BE
WHOLLY AT YOUR OWN RISK AND RESPONSIBILITY.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT WILL HIKVISION, ITS
DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL,
CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES
Video Intercom Door Station·User Manual
ii
FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, SECURITY BREACHES, OR LOSS OF DATA
OR DOCUMENTATION, IN CONNECTION WITH THE USE OF OR RELIANCE ON THIS MANUAL, EVEN IF
HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY OR CERTAIN
DAMAGES, SO SOME OR ALL OF THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU.
Support
Should you have any questions, please do not hesitate to contact your local dealer.
Video Intercom Door Station·User Manual
iii
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may
cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are
marked with "CE" and comply therefore with the applicable
harmonized European standards listed under the EMC Directive
2014/30/EU, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info
Video Intercom Door Station·User Manual
iv
2006/66/EC (battery directive): This product contains a battery that
cannot be disposed of as unsorted municipal waste in the European
Union. See the product documentation for specific battery information.
The battery is marked with this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling,
return the battery to your supplier or to a designated collection point.
For more information see: www.recyclethis.info
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.
Video Intercom Door Station·User Manual
v
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to
avoid danger or property loss.
The precaution measure is divided into Warnings and Cautions:
Warnings: Neglecting any of the warnings may cause serious injury or death.
Cautions: Neglecting any of the cautions may cause injury or equipment damage.
Warnings
The working temperature of the device is from -40º C to 60º C.
All the electronic operation should be strictly compliance with the electrical safety
regulations, fire prevention regulations and other related regulations in your local
region.
Please use the power adapter, which is provided by normal company. The power
consumption cannot be less than the required value.
Do not connect several devices to one power adapter as adapter overload may
cause over-heat or fire hazard.
Please make sure that the power has been disconnected before you wire, install
or dismantle the device.
When the product is installed on wall or ceiling, the device shall be firmly fixed.
If smoke, odors or noise rise from the device, turn off the power at once and
unplug the power cable, and then please contact the service center.
If the product does not work properly, please contact your dealer or the nearest
service center. Never attempt to disassemble the device yourself. (We shall not
assume any responsibility for problems caused by unauthorized repair or
maintenance.)
The power supply must conform to LPS. The recommended adaptor models and
manufacturers are shown as below. Use the attached adaptor, and do not change
the adaptor randomly.
Model
Manufacturer
Standard
DSA-12PFG-12 FCH 120100
Dee Van Electronics Co., Ltd.
GB
DSA-12PFG-12 FEU 120100
Dee Van Electronics Co., Ltd.
EN
DSA-12PFT-12FUS120100
Dee Van Electronics Co., Ltd.
ANSI
Warnings Follow
these safeguards to
prevent serious
injury or death.
Cautions Follow these
precautions to prevent
potential injury or
material damage.
Video Intercom Door Station·User Manual
vi
Model
Manufacturer
Standard
DSA-12PFG-12 FUK 120100
Dee Van Electronics Co., Ltd.
BSW
DSA-12PFG-12 FAU 120100
Dee Van Electronics Co., Ltd.
AS
Cautions
Do not drop the device or subject it to physical shock, and do not expose it to high
electromagnetism radiation. Avoid the equipment installation on vibrations
surface or places subject to shock (ignorance can cause equipment damage).
Do not place the device in extremely hot (refer to the specification of the device
for the detailed operating temperature), cold, dusty or damp locations, and do not
expose it to high electromagnetic radiation.
The device cover for indoor use shall be kept from rain and moisture.
Exposing the equipment to direct sun light, low ventilation or heat source such as
heater or radiator is forbidden (ignorance can cause fire danger).
Do not aim the device at the sun or extra bright places. A blooming or smear may
occur otherwise (which is not a malfunction however), and affecting the
endurance of sensor at the same time.
Please use the provided glove when open up the device cover, avoid direct
contact with the device cover, because the acidic sweat of the fingers may erode
the surface coating of the device cover.
Please use a soft and dry cloth when clean inside and outside surfaces of the
device cover, do not use alkaline detergents.
Please keep all wrappers after unpack them for future use. In case of any failure
occurred, you need to return the device to the factory with the original wrapper.
Transportation without the original wrapper may result in damage on the device
and lead to additional costs.
Improper use or replacement of the battery may result in hazard of explosion.
Replace with the same or equivalent type only. Dispose of used batteries
according to the instructions provided by the battery manufacturer.
Video Intercom Door Station·User Manual
vii
Table of Contents
1 Overview ...................................................................................................... 1
1.1 Introduction ........................................................................................................ 1
1.2 Main Features ..................................................................................................... 1
2 Appearance .................................................................................................. 2
2.1 Appearance of DS-KV8X02-IM .............................................................................. 2
2.2 Appearance of DS-KV8102-XP .............................................................................. 3
3 Typical Application ....................................................................................... 5
3.1 Typical Application of DS-KV8X02-IM .................................................................... 5
3.2 Typical Application of DS-KV8102-XP .................................................................... 6
4 Terminal and Wiring ..................................................................................... 7
4.1 Terminal Description ............................................................................................ 7
4.2 Wiring Description ............................................................................................... 8
4.2.1 Door Lock Wiring........................................................................................... 8
4.2.2 Door Magnetic Wiring ................................................................................... 9
4.2.3 Exit Button Wiring ......................................................................................... 9
4.2.4 Alarm Device Input Wiring ........................................................................... 10
4.2.5 RS-485 Card Reader Wiring .......................................................................... 11
4.2.6 External Elevator Controller Wiring .............................................................. 11
5 Installation ................................................................................................. 12
5.1 Installation of DS-KV8X02-IM ............................................................................. 12
5.1.1 Gang Box for DS-KV8X02-IM ........................................................................ 12
5.1.2 Wall Mounting with Gang Box of DS-KV8X02-IM ........................................... 13
5.2 Installation of DS-KV8102-XP .............................................................................. 14
5.2.1 Installation Plate for DS-KV8102-XP .............................................................. 14
5.2.2 Wall Mounting with Gang Box of DS-KV8102-XP ........................................... 15
6 Before You Start ......................................................................................... 17
7 Remote Operation via Batch Configuration Tool ......................................... 18
7.1 Activating Device Remotely ................................................................................ 18
7.2 Editing Network Parameters............................................................................... 19
7.3 Adding Device ................................................................................................... 20
7.3.1 Adding Online Device .................................................................................. 20
7.3.2 Adding by IP Address ................................................................................... 21
7.3.3 Adding by IP Segment .................................................................................. 22
7.4 Configuring Devices Remotely ............................................................................ 23
7.4.1 System ........................................................................................................ 23
7.4.2 Video Intercom ........................................................................................... 28
7.4.3 Network ...................................................................................................... 32
Video Intercom Door Station·User Manual
viii
7.4.4 Video Display .............................................................................................. 34
7.5 Video Intercom Device Set-up Tool ..................................................................... 35
7.5.1 Setting a Community Structure .................................................................... 36
7.5.2 Setting Main/Sub Door Station .................................................................... 36
7.6 Batch Upgrading ................................................................................................ 39
7.6.1 Adding Devices for Upgrading ...................................................................... 39
7.6.2 Upgrading Devices ....................................................................................... 41
8 Remote Operation via iVMS-4200 .............................................................. 43
8.1 System Configuration ......................................................................................... 43
8.2 Device Management .......................................................................................... 44
8.2.1 Adding Video Intercom Devices ................................................................... 44
8.2.2 Modifying Network Information................................................................... 47
8.2.3 Resetting Password...................................................................................... 47
8.3 Configuring Devices Remotely via iVMS-4200 ..................................................... 49
8.4 Picture Storage .................................................................................................. 49
8.4.1 Adding Storage Server ................................................................................. 50
8.4.2 Formatting the HDDs ................................................................................... 51
8.4.3 Configuring Storage Server Picture Storage .................................................. 51
8.5 Video Intercom Configuration ............................................................................ 53
8.5.1 Group Management .................................................................................... 54
8.5.2 Card Management ....................................................................................... 59
8.5.3 Notice Management .................................................................................... 69
8.6 Device Arming Control ....................................................................................... 71
9 Local Operation .......................................................................................... 73
9.1 Calling Resident ................................................................................................. 73
9.1.1 Calling Resident (DS-KV8X02-IM).................................................................. 73
9.1.2 Calling Resident (DS-KV8102-XP) .................................................................. 74
9.2 Issuing Card ....................................................................................................... 75
9.3 Unlocking Door .................................................................................................. 76
Appendix....................................................................................................... 77
Installation Notice ................................................................................................... 77
Wiring Cables .......................................................................................................... 77
Video Intercom Door Station·User Manual
1
1 Overview
1.1 Introduction
The door station (V series) can realize functions such as video intercom, access control,
one-card system, zone alarm, and visitor messages to form a complete smart community
video intercom solution.
The door station (V series) is mainly applied in the villa, and can works as door station,
outer door station, and doorphone.
1.2 Main Features
Video intercom function
HD video surveillance (Max. resolution 1280×720@25fps, WDR, 120° wide angle)
Self-adaptive light supplement
Access control function
Activating card via local station function (This function will be invalid if the card
has been activated via iVMS-4200)
Auto-uploading captured pictures to FTP or iVMS-4200 Client while unlocking the
door
Door magnetic alarm and tamper alarm function
Noise suppression and echo cancellation
Remote upgrade, batch setting functions
Video Intercom Door Station·User Manual
2
2 Appearance
2.1 Appearance of DS-KV8X02-IM
For device DS-KV8X02-IM, the number of call buttons varies according to its model. Take
the figure of device DS-KV8402-IM as an example.
For device DS-KV8102-IM, there is only 1 call button.
For device DS-KV8202-IM, there are 2 call buttons.
For device DS-KV8402-IM, there are 4 call buttons.
Figure 2-1 Appearance of DS-KV8402-IM
Table 2-1 Description of DS-KV8X02-IM
Models
No.
Description
DS-KV8102-IM
DS-KV8202-IM
DS-KV8402-IM
1
Low Illumination Supplement
Light
2
Built-in Camera
3
Card Induction Area
4
Call Button
5
Loudspeaker
6
Room No. (Customized)
7
Microphone
8
Tamper Button
Video Intercom Door Station·User Manual
3
You need not customize the Room No. for device DS-KV8102-IM.
Default settings of call button: when you press the call button, it calls the resident;
and when you hold down the call button, it calls the center.
You can change the calling mode of the call button via Batch Configuration Tool or
iVMS-4200 client software. See 7.4.2 Video Intercom for detail steps.
2.2 Appearance of DS-KV8102-XP
1
2
3
4
5
Figure 2-2 Appearance of DS-KV8102-XP
Table 2-2 Description of DS-KV8102-XP
Models
No.
Description
DS-KV8102-IP
DS-KV8102-VP
1
Microphone
2
Low Illumination Supplement
Light
3
Built-in Camera
4
Card Induction Area
5
Call Button
6
Tamper Button
7
Loudspeaker
Video Intercom Door Station·User Manual
4
Default settings of call button: when you press the call button, it calls the resident;
and when you hold down the call button, it calls the center.
You can change the calling mode of the call button via Batch Configuration Tool or
iVMS-4200 client software. See 7.4.2 Video Intercom for detail steps.
Video Intercom Door Station·User Manual
5
3 Typical Application
3.1 Typical Application of DS-KV8X02-IM
Please refer to the following figure for typical application of DS-KV8102-IM/
DS-KV8202-IM/ DS-KV8402-IM door station.
Master Station
Video/Audio
Distributor
Client Software
Door Station
IP Camera
LAN
Card Reader
Network Cable
Optical Fiber
One Resident
RS-485
Wi-Fi/3G/4G
Resident 1
1F
2F
Resident 2
Resident 1Resident 2
Indoor
Extension 2
Indoor
Extension 2
House
Internet
App
Wi-Fi
Wi-Fi/3G/4G
Figure 3-1 Typical Application of DS-KV8X02-IM
Video Intercom Door Station·User Manual
6
3.2 Typical Application of DS-KV8102-XP
Please refer to the following figures for typical applications of DS-KV8102-IP/
DS-KV8102-VP door station.
Switch
Client Software
Network Cable
Optical Fiber
Door Station
Resident 1
IPC
Video/Audio
Distributor
LAN
Indoor
Extension 1
Indoor
Extension 2
Master Station
Card Reader
RS-485/3G/4G
Wi-Fi
House
Internet
App
Wi-Fi
Wi-Fi/
3G/4G
Figure 3-2 Typical Application of DS-KV8102-XP
Video Intercom Door Station·User Manual
7
4 Terminal and Wiring
4.1 Terminal Description
Please refer to the following figure for terminals and interfaces of door station.
①-⑤
⑥-⑦
⑧-⑨
⑩-⑫
⑬
Figure 4-1 Terminals and Interfaces
Table 4-1 Descriptions of Terminals and Interfaces
Terminals and Interfaces
Name
No.
Color
Description
ALARM IN
1
YELLOW/PURPLE
ALARM_1
2
YELLOW/ORANGE
ALARM_2
3
YELLOW/GREEN
ALARM_3
4
YELLOW/BROWN
ALARM_4
5
YELLOW/BLACK
ALARM_GND
Power Supply
6
RED
DC 12V Power Supply Input
GND 7 BLACK
Grounding
RS485
8
ORANGE
RS485+
9
YELLOW
RS485-
ALARM OUT
10
PINK
DR_NC
11
BLUE
DR_NO
12
GREEN
DR_COM
LAN
13
LAN
Network Interface
Video Intercom Door Station·User Manual
8
4 I/O Input terminals (ALARM_1~ALARM_4) can be set as door magnetic input or
door switch key input, and terminal ALARM_GND is for grounding connection.
1 I/O Output terminal can be enabled for controlling electric lock or disabled.
4.2 Wiring Description
4.2.1 Door Lock Wiring
Figure 4-2 Door Lock Wiring
Terminal DR_NC/DR_COM is set as default for connecting magnetic lock/electric
bolt; terminal DR_NO/DR_COM is set as default for connecting electric strike.
To connect electric lock, it is required to set the output of terminal
DR_NC/DR_COM/DR_NO to be electric lock with Batch Configuration Tool or
iVMS-4200 client software.
Video Intercom Door Station·User Manual
9
4.2.2 Door Magnetic Wiring
Figure 4-3 Door Magnetic Wiring
To connect door magnetic, it is required to set the input of one alarm in terminal
(ALARM_1, ALARM_2, ALARM_3, or ALARM_4) to be door magnetic with Batch
Configuration Tool or iVMS-4200 client software.
4.2.3 Exit Button Wiring
Figure 4-4 Exit Button Wiring
Video Intercom Door Station·User Manual
10
To connect exit button, it is required to set the input of one alarm in terminal (ALARM_1,
ALARM_2, ALARM_3, or ALARM_4) to be exit button with Batch Configuration Tool or
iVMS-4200 client software.
4.2.4 Alarm Device Input Wiring
Figure 4-5 Alarm Device Input Wiring
To connect other alarm devices, it is required to set the input of one alarm in terminal
(ALARM_1, ALARM_2, ALARM_3, or ALARM_4) to be custom with Batch Configuration
Tool or iVMS-4200 client software.
Video Intercom Door Station·User Manual
11
4.2.5 RS-485 Card Reader Wiring
Figure 4-6 RS-485 Card Reader Wiring
4.2.6 External Elevator Controller Wiring
You can connect the door station to the elevator controller via RS-485 wire.
There are 4 groups of RS-485 interfaces on the elevator controller: group A, group B,
Group C, and Group D. Group C is used to connect to the door station.
Figure 4-7 External Elevator Controller Wiring
Video Intercom Door Station·User Manual
12
5 Installation
5.1 Installation of DS-KV8X02-IM
To install the door station onto the wall, you are required to utilize a matched gang box.
5.1.1 Gang Box for DS-KV8X02-IM
Please refer to the following figures for the dimensions of gang box for DS-KV8102-IM/
DS-KV8202-IM/ DS-KV8402-IM door station.
89
168
49
54
97
50
45
100
73.92
Figure 5-1 Front View & Rear View (DS-KV8X02-IM)
The dimension of gang box for model DS-KV8102-IM/ DS-KV8202-IM/
DS-KV8402-IM door station is: 89 (width) × 168 (length) ×38 (depth) mm.
The dimensions above are theoretical. The actual size can be slightly different
from the theoretical dimension.
Video Intercom Door Station·User Manual
13
5.1.2 Wall Mounting with Gang Box of DS-KV8X02-IM
Steps:
1. Take the gang box and screws from the packing box.
2. Chisel a hole in the wall for inserting the gang box. The size of the hole should be 90
(width) ×170 (length) × 38(depth) mm.
3. Insert the gang box into the hole and fix it with 4 PA4 screws, as shown in the figure
below.
PA4 Screws
Figure 5-2 Insert the Gang Box (DS-KV8X02-IM)
4. After fixing the gang box, install the door station into the gang box according to the
direction of the arrow, as shown in the figure below.
Figure 5-3 Insert the Door Station (DS-KV8X02-IM)
5. After inserting the door station into the gang box, pull the device downwards to hook
the door station with the gang box.
6. Secure the door station by inserting the fixing screw according to the direction of the
arrow of the figure below.
Video Intercom Door Station·User Manual
14
M4 Screw
Figure 5-4 Secure the Door Station (DS-KV8X02-IM)
5.2 Installation of DS-KV8102-XP
5.2.1 Installation Plate for DS-KV8102-XP
To install the DS-KV8102-XP model onto the wall, an installation plate and a gang box are
required.
20
69
18
41.48
9.3
72.7
Hollow Area
91.6
Figure 5-5 Dimensions of Installation Plate (DS-KV8102-XP)
Video Intercom Door Station·User Manual
15
The dimension of gang box for model DS-KV8102-IP/ DS-KV8102-VP door station is:
75 (width) × 75 (length) × 50 (depth) mm.
The dimensions above are theoretical. The actual size can be slightly different
from the theoretical dimension.
5.2.2 Wall Mounting with Gang Box of DS-KV8102-XP
Steps:
1. Take the gang box, installation plate and screws from the packing box.
2. Chisel a hole in the wall for inserting the gang box. The size of the hole should be 76
(width) × 76 (length) × 50 (depth) mm.
3. Insert the gang box into the hole, as shown in the figure below.
Figure 5-6 Insert the Gang Box (DS-KV8102-XP)
4. Attach the installation plate to the gang box and align the screw holes of the
installation plate with the screw holes of the gang box.
5. Insert 2 PA4 screws and a KA4 screw into the screw holes to fix the installation plate
onto the gang box. (The KA4 screw is optional.)
PA4 Screws
KA4 Screw
Figure 5-7 Attach the Installation Plate (DS-KV8102-XP)
Video Intercom Door Station·User Manual
16
6. After installing the installation plate, install the door station by inserting the rear
component into the hollow area of the installation plate.
While inserting the door station into the installation plate, incline the device by 5~10°,
as shown in the figure below.
Hollow Area
Rear Component
Figure 5-8 Install the Door Station (DS-KV8102-XP)
7. Secure the door station by inserting the fixing screw according to the direction of the
arrow of the figure below.
KM3 Screw
Figure 5-9 Secure the Door Station (DS-KV8102-XP)
Video Intercom Door Station·User Manual
17
6 Before You Start
For the first time use of the device, you are required to activate the device. You can
activate the device and set the device password via internet with Batch Configuration
Tool, or with iVMS-4200 client software, or with Video Intercom Set-up Tool.
To activate the device with Batch Configuration Tool or iVMS-4200, refer to 7
Remote Operation via Batch Configuration Tool and 8 Remote Operation via
iVMS-4200.
Please refer to 7.1 for creating the device password.
Video Intercom Door Station·User Manual
18
7 Remote Operation via Batch
Configuration Tool
7.1 Activating Device Remotely
Purpose:
You are required to activate the device first by setting a strong password for it before
you can use the device.
Activation via Batch Configuration Tool, and Activation via iVMS-4200 are supported.
Here take activation via Batch Configuration Tool as example to introduce the device
activation. Please refer to the user manual for the activation via iVMS-4200.
Steps:
1. Run the Batch Configuration Tool.
Figure 7-1 Selecting Inactive Device
2. Select an inactivated device and click the Activate button.
Figure 7-2 Activation
3. Create a password, and confirm the password.
Loading...