Video Intercom Indoor Station
Quick Start Guide
Video Intercom Indoor Station·Quick Start Guide
i
Quick Start Guide
© 2018 Hangzhou Hikvision Digital Technology Co., Ltd.
This quick start guide is intended for users of the models below:
Series
Model
Indoor Station (6-Series)
DS-KH6310-W
DS-KH6310
DS-KH6310-WL
DS-KH6210-L
Indoor Station (8-Series)
DS-KH8301-WT
DS-KH8300-T
It includes instructions on how to use the Product. The software embodied in the
Product is governed by the user license agreement covering that Product.
About this Manual
This Manual is subject to domestic and international copyright protection. Hangzhou
Hikvision Digital Technology Co., Ltd. (“Hikvision”) reserves all rights to this manual. This
manual cannot be reproduced, changed, translated, or distributed, partially or wholly, by
any means, without the prior written permission of Hikvision.
Trademarks
and other Hikvision marks are the property of Hikvision and are
registered trademarks or the subject of applications for the same by Hikvision and/or its
affiliates. Other trademarks mentioned in this manual are the properties of their
respective owners. No right of license is given to use such trademarks without express
permission.
Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, HIKVISION MAKES NO WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, REGARDING THIS MANUAL.
HIKVISION DOES NOT WARRANT, GUARANTEE, OR MAKE ANY REPRESENTATIONS REGARDING THE
USE OF THE MANUAL, OR THE CORRECTNESS, ACCURACY, OR RELIABILITY OF INFORMATION
CONTAINED HEREIN. YOUR USE OF THIS MANUAL AND ANY RELIANCE ON THIS MANUAL SHALL BE
WHOLLY AT YOUR OWN RISK AND RESPONSIBILITY.
Video Intercom Indoor Station·Quick Start Guide
ii
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT WILL HIKVISION, ITS
DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL,
CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES
FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, SECURITY BREACHES, OR LOSS OF DATA
OR DOCUMENTATION, IN CONNECTION WITH THE USE OF OR RELIANCE ON THIS MANUAL, EVEN IF
HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY OR CERTAIN
DAMAGES, SO SOME OR ALL OF THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU.
Support
Should you have any questions, please do not hesitate to contact your local dealer.
Video Intercom Indoor Station·Quick Start Guide
iii
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may
cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are
marked with "CE" and comply therefore with the applicable harmonized
European standards listed under the EMC Directive 2014/30/EU, the
RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot
be disposed of as unsorted municipal waste in the European Union. For
proper recycling, return this product to your local supplier upon the
purchase of equivalent new equipment, or dispose of it at designated
collection points. For more information see: www.recyclethis.info
2006/66/EC (battery directive): This product contains a battery that
cannot be disposed of as unsorted municipal waste in the European
Union. See the product documentation for specific battery information.
The battery is marked with this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling,
return the battery to your supplier or to a designated collection point.
For more information see: www.recyclethis.info
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.
Video Intercom Indoor Station·Quick Start Guide
iv
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to
avoid danger or property loss.
The precaution measure is divided into Warnings and Cautions:
Warnings: Neglecting any of the warnings may cause serious injury or death.
Cautions: Neglecting any of the cautions may cause injury or equipment damage.
Warnings
The working temperature of the device is from -10º C to 55º C.
All the electronic operation should be strictly compliance with the electrical safety
regulations, fire prevention regulations and other related regulations in your local
region.
Please use the power adapter, which is provided by normal company. The power
consumption cannot be less than the required value.
Do not connect several devices to one power adapter as adapter overload may cause
over-heat or fire hazard.
Please make sure that the power has been disconnected before you wire, install or
dismantle the device.
When the product is installed on wall or ceiling, the device shall be firmly fixed.
If smoke, odors or noise rise from the device, turn off the power at once and unplug
the power cable, and then please contact the service center.
If the product does not work properly, please contact your dealer or the nearest
service center. Never attempt to disassemble the device yourself. (We shall not
assume any responsibility for problems caused by unauthorized repair or
maintenance.)
Cautions
Do not drop the device or subject it to physical shock, and do not expose it to high
electromagnetism radiation. Avoid the equipment installation on vibrations surface
or places subject to shock (ignorance can cause equipment damage).
Do not place the device in extremely hot (refer to the specification of the device for
the detailed operating temperature), cold, dusty or damp locations, and do not
expose it to high electromagnetic radiation.
The device cover for indoor use shall be kept from rain and moisture.
Warnings Follow
these safeguards to
prevent serious
injury or death.
Cautions Follow these
precautions to prevent
potential injury or
material damage.
Video Intercom Indoor Station·Quick Start Guide
v
Exposing the equipment to direct sun light, low ventilation or heat source such as
heater or radiator is forbidden (ignorance can cause fire danger).
Do not aim the device at the sun or extra bright places. A blooming or smear may
occur otherwise (which is not a malfunction however), and affecting the endurance
of sensor at the same time.
Please use the provided glove when open up the device cover, avoid direct contact
with the device cover, because the acidic sweat of the fingers may erode the surface
coating of the device cover.
Please use a soft and dry cloth when clean inside and outside surfaces of the device
cover, do not use alkaline detergents.
Please keep all wrappers after unpack them for future use. In case of any failure
occurred, you need to return the device to the factory with the original wrapper.
Transportation without the original wrapper may result in damage on the device and
lead to additional costs.
Improper use or replacement of the battery may result in hazard of explosion.
Replace with the same or equivalent type only. Dispose of used batteries according
to the instructions provided by the battery manufacturer.
Video Intercom Indoor Station·Quick Start Guide
vi
Table of Contents
1 Appearance .................................................................................................. 1
1.1 Appearance of DS-KH8301-WT/ DS-KH8300-T .......................................................................... 1
1.2 Appearance of DS-KH6310-W/DS-KH6310 ............................................................................... 2
1.3 Appearance of DS-KH6310-WL/DS-KH6210-L ........................................................................... 3
2 Terminals and Wiring ................................................................................... 5
2.1 Terminal Description ................................................................................................................ 5
2.1.1 Terminals and Interfaces of DS-KH8301-WT/DS-KH8300-T ................................................ 5
2.1.2 Terminals and Interfaces of DS-KH6310-W/ DS-KH6310 .................................................... 6
2.1.3 Terminals and Interfaces of DS-KH6310-WL/ DS-KH6210-L ............................................... 7
2.2 Wiring Description ................................................................................................................... 7
2.2.1 Wiring of DS-KH8301-WT/DS-KH8300-T ............................................................................ 7
2.2.2 Wiring of DS-KH6310-W/DS-KH6310 ................................................................................. 8
2.2.3 Wiring of DS-KH6310-WL/DS-KH6210-L ............................................................................ 9
3 Installation ................................................................................................. 10
3.1 Installation Accessory Description .......................................................................................... 10
3.2 Wall Mounting with Junction Box ........................................................................................... 10
4 Getting Started ........................................................................................... 12
4.1 Activate Indoor Station ........................................................................................................... 12
4.2 Set SIP Sever ........................................................................................................................... 13
4.2.1 Set Private SIP .................................................................................................................. 13
4.2.2 Set Standard SIP .............................................................................................................. 14
4.3 Set Network ............................................................................................................................ 16
4.3.1 Set Indoor Station Network Parameters .......................................................................... 16
4.3.2 Set Linked Device IP ......................................................................................................... 17
4.4 Set Indoor Station No. ............................................................................................................ 19
5 Appendix .................................................................................................... 22
5.1 Installation Notice .................................................................................................................. 22
5.2 Wiring Cables ......................................................................................................................... 22
Video Intercom Indoor Station·Quick Start Guide
1
1 Appearance
1.1 Appearance of DS-KH8301-WT/ DS-KH8300-T
Figure 1-1 Front Panel
Table 1-1 Components Description
No.
Description
1
Built-in Camera (Only
DS-KH8301-WT supports)
2
Power Supply Indicator
3
Information Indicator
4
Alarm Indicator
5
SOS Touch Key
6
Unlock Touch Key
7
Live View Touch Key
8
Management Center Touch Key
9
LCD Display Screen
10
Microphone
Figure 1-2 Rear Panel
Table 1-2 Components Description
No.
Description
11
TF Card Slot
12
Serial Port
13
Mechanical Switch
14
Power Supply Indicator
15
Network Interface
16
Loudspeaker
Hold the SOS touch key to trigger a SOS alarm and upload the alarm message to the
management center (iVMS-4200 client software or the master station).
The Unlock key ( ) is valid only when does the indoor station speak with the door
station or open the live view of the door station.
Video Intercom Indoor Station·Quick Start Guide
2
1.2 Appearance of DS-KH6310-W/DS-KH6310
Figure 1-3 Front Panel
Table 1-3 Components Description
No.
Description
1
Power Supply Indicator
2
Information Indicator
3
Alarm Indicator
4
SOS Key
5
Unlock Key
6
Live View Key
7
Management Center Key
8
LCD Display Screen
9
Microphone
Figure 1-4 Rear Panel
Table 1-4 Components Description
No.
Description
10
Power Supply Interface
11
Network Interface
12
Terminals
13
Loudspeaker
Hold the SOS touch key to trigger a SOS alarm and upload the alarm message to the
management center (iVMS-4200 client software or the master station).
The Unlock key ( ) is valid only when does the indoor station speak with the door
station or open the live view of the door station.
Video Intercom Indoor Station·Quick Start Guide
3
1.3 Appearance of DS-KH6310-WL/DS-KH6210-L
Figure 1-5 Front Panel
Table 1-5 Components Description
No.
Description
1
Power Supply Indicator
2
Information Indicator
3
Alarm Indicator
4
SOS Key
5
Unlock Key
6
Live View Key
7
Management Center Key
8
LCD Display Screen
9
Microphone
Figure 1-6 Rear Panel
Table 1-6 Components Description
No.
Description
10
Power Supply
11
Network Interface
12
Terminals
13
Loudspeaker
Hold the SOS touch key to trigger a SOS alarm and upload the alarm message to the
management center (iVMS-4200 client software or the master station).
The Unlock key ( ) is valid only when does the indoor station speak with the door
station or open the live view of the door station.
For DS-KH6210-L indoor station, there are different meanings when you press or hold
the four mechanical keys.
Video Intercom Indoor Station·Quick Start Guide
4
Keys
Hold
Press
SOS Key
Return Key
Direction Keys▲and◄/Unlock Key
Live View Key Alarm
Direction Keys▼and►
Management Center Key
Confirm Key
Video Intercom Indoor Station·Quick Start Guide
5
2 Terminals and Wiring
2.1 Terminal Description
2.1.1 Terminals and Interfaces of DS-KH8301-WT/DS-KH8300-T
Figure 2-1 Terminals of DS-KH8301-WT/DS-KH8300-T
Table 2-1 Descriptions of Terminals and Interfaces
Name
No.
Interface
Description
485
Communication
Port
A1
RS485B+
RS-485 Communication Interfaces
A2
RS485B-
A3
RS485A+
A4
RS485A-
Grounding
A5
GND
Grounding
A6
GND
Grounding
ALARM OUT
(Alarm Output)
A7
COM1
Alarm Relay Output Terminal 1 (Dry Contact)
A8
NO1
A9
COM2
Alarm Relay Output Terminal 2 (Dry Contact)
A10
NO2
ALARM IN
(Zone Input)
B1
JIN8
Zone Detector Input Terminal 8
B2
JIN7
Zone Detector Input Terminal 7
B3
JIN6
Zone Detector Input Terminal 6
B4
JIN5
Zone Detector Input Terminal 5
B5
GND
Grounding
B6
GND
Grounding
Video Intercom Indoor Station·Quick Start Guide
6
Name
No.
Interface
Description
B7
JIN4
Zone Detector Input Terminal 4
B8
JIN3
Zone Detector Input Terminal 3
B9
JIN2
Zone Detector Input Terminal 2
B10
JIN1
Zone Detector Input Terminal 1
2.1.2 Terminals and Interfaces of DS-KH6310-W/ DS-KH6310
Figure 2-2 terminals of DS-KH6310-W/DS-KH6310
Table 2-2 Descriptions of Terminals and Interfaces
Name
No.
Interface
Description
Terminals
A1
RS485-
RS-485 Communication Interfaces
A2
RS485+
A3
AIN1
Zone Detector Input Terminal 1
A4
AIN2
Zone Detector Input Terminal 2
A5
AIN3
Zone Detector Input Terminal 3
A6
AIN4
Zone Detector Input Terminal 4
B1
AIN5
Zone Detector Input Terminal 5
B2
AIN6
Zone Detector Input Terminal 6
B3
AIN7
Zone Detector Input Terminal 7
B4
AIN8
Zone Detector Input Terminal 8
B5
AOUT
Alarm Relay Output
B6
GND
Grounding
Video Intercom Indoor Station·Quick Start Guide
7
2.1.3 Terminals and Interfaces of DS-KH6310-WL/ DS-KH6210-L
Figure 2-3 Terminals of DS-KH6310-WL/DS-KH6210-L
Table 2-3 Terminals Description
Name
No.
Interface
Description
Terminals
A1
AIN1
Zone Detector Input Terminal 1
A2
AIN2
Zone Detector Input Terminal 2
A3
GND
Grounding
2.2 Wiring Description
2.2.1 Wiring of DS-KH8301-WT/DS-KH8300-T
There are 20 pins in the terminal on the rear panel of the indoor station: 4 RS-485 pins,
4 GND pins, 4 alarm output pins, and 8 alarm input pins.
To access the alarm input device, refer to Figure 2-4.
To access the alarm output device, refer to Figure 2-5.
Figure 2-4 Wiring Description (Alarm Input Device)
Video Intercom Indoor Station·Quick Start Guide
8
Figure 2-5 Wiring Description (Alarm Output Device)
2.2.2 Wiring of DS-KH6310-W/DS-KH6310
There are 12 pins in the terminal on the rear panel of the indoor station: 2 RS-485 pins,
1 GND pin, 1 alarm output pin, and 8 alarm input pins.
To access the alarm input device, refer to Figure 2-6.
To access the alarm output device, refer to Figure 2-7.
Figure 2-6 Wiring Description (Alarm Input Device)
Video Intercom Indoor Station·Quick Start Guide
9
Figure 2-7 Wiring Description (Alarm Output Device)
2.2.3 Wiring of DS-KH6310-WL/DS-KH6210-L
There are 3 available pins in the terminal on the rear panel of the indoor station: 2 alarm
input pins and 1 GND pin.
To access the alarm input device, refer to Figure 2-8.
Figure 2-8 Wiring Description (Alarm Input Device)
Video Intercom Indoor Station·Quick Start Guide
10
3 Installation
3.1 Installation Accessory Description
The wall mounting plate and the junction box are required to install the indoor station
onto the wall.
Junction boxes for 8-series and 6-series indoor stations are the same.
The dimension of junction box should be 75 mm (width) × 75 mm (length) × 50 mm
(depth).
The dimension of wall mounting plate is shown in Figure 3-1.
Figure 3-1 Wall Mounting Plate
3.2 Wall Mounting with Junction Box
Wall mounting installations are the same for the 6-series indoor stations and the
8-series indoor stations. Here we take the wall mounting of DS-KH6310 model as an
example.
Before you start:
Make sure the device in the package is in good condition and all the assembly parts
are included.
The power supply the indoor station supports is 12 VDC. Please make sure your
power supply matches your indoor station.
Make sure all the related equipment is power-off during the installation.
Check the product specification for the installation environment.
Video Intercom Indoor Station·Quick Start Guide
11
Steps:
1. Chisel a hole in the wall. The size of the hole should be 76 mm (width) × 76 mm
(length) × 50 mm (depth).
2. Insert the junction box to the hole chiseled on the wall.
3. Fix the wall mounting plate to the junction box with 2 screws.
Screws
Wall Mounting
Plate
Junction Box
Figure 3-2 Installing the Plate
4. Hook the indoor station to the wall mounting plate tightly by inserting the plate hooks
into the slots on the rear panel of the indoor station, during which the lock catch will
be locked automatically.
Hooks
Slot Slot
Lock Catch
Figure 3-3 Hooking the Indoor Station to the Plate
Video Intercom Indoor Station·Quick Start Guide
12
4 Getting Started
Here the local operation of indoor stations with touch screen is taken as example.
The DS-KH6210-L should be operated with physical keys. The SOS key works as a
return key; the Unlock key works as direction keys ▲and◄ to turn up and left; the
Live View key works as direction keys ▼and► to turn down and right; and the
Management Center key works as a confirm key.
4.1 Activate Indoor Station
You can configure and operate the indoor station only when you activate it. You must
create a password to activate the indoor station for your first time usage and when it is
not activated.
Steps:
1. Power on the device to enter the activation interface automatically.
Figure 4-1 Activation Interface (DS-KH8301-WT)
2. Create a password and confirm it.
3. Tap OK to activate the indoor station.
Video Intercom Indoor Station·Quick Start Guide
13
STRONG PASSWORD RECOMMENDED– We highly recommend you to create a strong
password of your own choosing (using a minimum of 8 characters, including
at least three kinds of following categories: upper case letters, lower case
letters, numbers, and special characters) in order to increase the security of
your product. And we recommend you reset your password regularly, especially in the
high security system, resetting the password monthly or weekly can better protect your
product.
4.2 Set SIP Sever
A SIP server connection is required and necessary for the indoor station to guarantee
the connection between the indoor station and the management center (master station)
in the same video intercom system.
2 types of SIP protocol are available for the indoor station: Private Protocol, and
Standard Protocol.
Rebooting the indoor station is required when you switch the SIP protocol between
the private SIP protocol and the standard SIP protocol.
All linked device IP should be configured again after you change the SIP protocol type.
The indoor extension does not support SIP sever settings.
4.2.1 Set Private SIP
The SIP server IP is required for you to set when you select Private Protocol, and the
SIP IP must be in the same network segment with the intercom devices in the system.
Steps:
1. Go to SIP Settings page to select SIP protocol type: Settings -> Configuration -> SIP
Settings.
2. Select Private Protocol.
Default admin password is 888999.
The default SIP protocol is private protocol.
Video Intercom Indoor Station·Quick Start Guide
14
Figure 4-2 SIP Protocol Selection
3. Tap Device to go to the device management page.
Figure 4-3 Device Management
4. Tap SIP Sever, and enter the IP address of the SIP server.
5. Tap to save the SIP server added.
4.2.2 Set Standard SIP
With the standard SIP, your indoor station can connect to any intercom device,
software client, and phones which also support the standard SIP.
Before you Start:
Video Intercom Indoor Station·Quick Start Guide
15
Make sure you have added a VoIP account in the standard SIP server.
Steps:
1. Go to SIP Settings page to select SIP protocol type: Settings -> Configuration -> SIP
Settings.
2. Select Standard Protocol.
Default admin password is 888999.
The default SIP protocol is private protocol.
Rebooting the indoor station is required when you change to Standard Protocol
from Private Protocol.
Figure 4-4 SIP Protocol Selection
3. Set VoIP account.
The account you entered here must be the same with the account you added in
the standard SIP server.
The phone number should be a numeric, which is up to 16 digits. And the phone
number will be the number you dial when you want to call the indoor station via
standard SIP.
Video Intercom Indoor Station·Quick Start Guide
16
Figure 4-5 Set VoIP Account
4. Tap to save the standard SIP settings.
4.3 Set Network
4.3.1 Set Indoor Station Network Parameters
Network connection is mandatory for the use of the indoor station. Set the network
parameters after activating the indoor station. What's more, the indoor station can work
normally in an intercom system only when its IP address is in the same network segment
with other devices in the same system.
The indoor station’s default IP address is 192.0.0.64.
Two ways are available for you to set indoor station's IP address: DHCP, and set IP
address manually.
Steps:
1. Tap Settings -> Configuration -> Network to go to the network settings page.
Default admin password is 888999.
Video Intercom Indoor Station·Quick Start Guide
17
Figure 4-6 Network Settings
2. Enable DHCP, then the indoor station can search and get an IP address automatically.
Skip the following steps if you have set an IP address for the indoor station by DHCP
function.
3. Set the IP address manually.
1) Tap to pop up the network parameters settings dialog box.
Figure 4-7 Network Settings Box
2) Enter IP address, subnet mask, and network gateway.
3) Tap OK.
4.3.2 Set Linked Device IP
Linked network parameters refers to the network parameters of devices (like door
station, doorphone, master station, center, etc.), to which the indoor station is linked.
Linked devices for the indoor station refers to door station, center, master station, and
doorphone.
With the private SIP protocol, intercom can be realized only when all these devices are
in the same network segment with the indoor station.
With the standard SIP protocol, intercom can be realized when all these devices support
the standard SIP protocol.
Video Intercom Indoor Station·Quick Start Guide
18
The doorphone does not support adding with the standard SIP protocol.
Here take door station network settings as example.
Steps:
1. Tap Settings -> Configuration -> Device to go to the device management page.
Default admin password is 888999.
Figure 4-8 Device Management (Private SIP)
Video Intercom Indoor Station·Quick Start Guide
19
Figure 4-9 Device Management (Standard SIP)
2. Tap Main Door Station to pop up the device information dialog box.
Figure 4-10 Device Information Dialog Box
3. Select a door station type based on your actual door station type, and set the door
station IP address.
4.4 Set Indoor Station No.
Indoor station No. and the indoor extension No. are numbers, which can be dialed by
other devices to call the indoor station and the indoor extension in an intercom system.
The indoor station No., is composed of the floor No. and the room No. For example, the
indoor station No. 401 refers to the room 1 on the fourth floor, and the indoor station
No. 512 refers to the room 12 on fifth floor, and the indoor station 2302 refers to the
room 2 on the 23rd floor.
The indoor extension No. Should be a numeric from 1 to 5.
Video Intercom Indoor Station·Quick Start Guide
20
Up to 5 indoor extensions can be set for 1 indoor station.
Steps:
1. Tap Settings -> Configuration -> Local Info to go to the indoor station No. settings
page.
Default admin password is 888999.
Figure 4-11 Set Indoor Station No.
2. Select Indoor Station to set the indoor station No. (Room No.) and the floor No.
For Example:
When set the Room No. as 2, and the Floor No as 2, then the indoor station No. is
202.
Video Intercom Indoor Station·Quick Start Guide
21
Figure 4-12 Set Indoor Station No.
3. Select Indoor Extension to set the indoor extension No. and the room name.
For Example:
Set the indoor extension No. as 1, and the room name as Hello Room.
What to do next
You can press 201 on the door station to call the indoor station, and press 1 on the
indoor station to call indoor extension.
Video Intercom Indoor Station·Quick Start Guide
22
5 Appendix
5.1 Installation Notice
While installing the indoor station, please make sure that the distance between any two
devices is far as possible to avoid the howling and echo. The distance between two
devices is recommended to be more than 10 meters.
Here the devices refer to indoor station, outdoor station and master station.
5.2 Wiring Cables
Cable
Specification
Power Cord of Door Station
RVV 2*1.0
Network Cable of Door Station
UTP-five Categories
Door Lock Wiring (With Door Magnetic)
RVV 4*1.0
Door Lock Wiring (Without Door Magnetic)
RVV 2*1.0
Exit Button Wiring
RVV 2*0.5
External Card Reader Wiring
RVVP 4*0.75
Video Intercom Indoor Station·Quick Start Guide
23
UD09722B
Loading...