HIKVISION DS-7604NI-SE, DS-7608NI-SE, DS-7616NI-SE, DS-7604NI-SE/N, DS-7608NI-SE/N Quick Operation Manual

Network Video Recorder

Quick Operation Guide

UD.6L0202B1057A01

Quick Operation Guide of DS-7600NI-SE&V(P) Series NVR

1

Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer.
This manual is applicable to the models listed in the following table.

Series

Model

Type

7600NI-SE

DS-7604NI-SE
DS-7608NI-SE
DS-7616NI-SE

Network Video Recorder

7600NI-SE/N

DS-7604NI-SE/N
DS-7608NI-SE/N
DS-7616NI-SE/N

Network Video Recorder

7600NI-SE/P

DS-7604NI-SE/P
DS-7608NI-SE/P
DS-7616NI-SE/P

Network Video Recorder

7600NI-V

DS-7604NI-V
DS-7608NI-V
DS-7616NI-V

Network Video Recorder

7600NI-VP

DS-7604NI-VP
DS-7608NI-VP
DS-7616NI-VP

Network Video Recorder

NVR Pre-Installation

The DS-7600NI-SE, DS-7600NI-SE/N, DS-7600NI-SE/P, DS-7600NI-V, and DS-7600NI-VP series NVR are
highly advanced surveillance equipment that should be installed with care. Please take into consideration the
following precautionary steps before installation of the NVR.

1. Keep all liquids away from the NVR.

2. Install the NVR in a well-ventilated and dust-free area.

3. Ensure environmental conditions meet factory specifications.

4. Install a manufacturer recommended HDD.

NVR Installation

During the installation of the NVR:

1. Use brackets for rack mounting.

2. Ensure there is ample room for audio and video cables.

3. When installing cables, ensure that the bend radius of the cables are no less than five times than its diameter.

4. Connect both the alarm and RS-485 cable.

5. Allow at least 2cm (~0.75-inch) of space between racks mounted devices.

6. Ensure the NVR is grounded.

7. Environmental temperature should be within the range of -10 ºC ~ 55 ºC , 14ºF ~ 131ºF.

8. Environmental humidity should be within the range of 10% ~ 90%.

Hard Disk Installation

Before you start:

Before installing a hard disk drive (HDD), please make sure the power is disconnected from the NVR. A factory
recommended HDD should be used for this installation.
Up to 2 SATA hard disks can be installed on your NVR.
Tools Required: Screwdriver.

Steps (for DS-7600NI-SE, DS-7600NI-SE/N and DS-7600NI-SE/P):

Note: The installation steps of DS-7600NI-SE/N and DS-7600NI-SE/P are the same as DS-7604/08NI-SE, so we

take the installation steps of DS-7604NI-SE as example.

1. Remove the cover from the NVR by unfastening the screws on the back and side.

Quick Operation Guide of DS-7600NI-SE&V(P) Series NVR

2

2. Connect one end of the data cable to the motherboard of NVR and the other end to the HDD.

3. Connect the power cable to the HDD.

4. Place the HDD on the bottom of the device and then fasten the screws on the bottom

to fix the HDD.

Quick Operation Guide of DS-7600NI-SE&V(P) Series NVR

3

5. Re-install the cover of the NVR and fasten screws.

Steps (for DS-7600NI-V and DS-7600NI-VP):

1. Fasten the hard disk mounting handle to the hard disk with screws.

2. Insert the key and turn in clockwise direction to open the panel lock.

3. Open the front panel.

4. Insert the hard disk along the slot until it is placed into position.

Quick Operation Guide of DS-7600NI-SE&V(P) Series NVR

4

5. Repeat the above steps to install other hard disks onto the NVR. After having finished the installation of all
hard disks, close the front panel and lock it with the key again.

Quick Operation Guide of DS-7600NI-SE&V(P) Series NVR

5

Front Panel

DS-7600NI-SE, DS-7600NI-SE/N, and DS-7600NI-SE/P

① Status Indicator(Power, Status, Tx/Rx)

② USB Interface

DS-7600NI-V and DS-7600NI-VP

① HDD Status Indicators

② Panel Lock

③ Running Status Indicator

④ USB Interface

Quick Operation Guide of DS-7600NI-SE&V(P) Series NVR

6

Rear Panel

DS-7604NI-SE/N

DS-7604&7608&7616NI-SE

DS-7608&7616NI-SE/N

No.

Item

Description

1

LAN Network Interface

Connector for LAN (Local Area Network).

2

RS-485 Interface

Connects to RS-485 devices.

3

Power Supply

12VDC power supply

4

Power Switch

Switch for turning on/off the device.

5

USB Interface

Universal Serial Bus (USB) ports for additional devices such as USB
mouse and USB Hard Disk Drive (HDD).

6

GND

Ground (needs to be connected when NVR starts up).

7

HDMI Interface

HDMI video output connector.

8

VGA Output

DB9 connector for VGA output. Display local video output and menu.

9

Audio In

RCA connector for voice talk input

10

Audio Out

RCA connector for audio output

11

Network Interfaces with
switch function
(for DS-7600NI-SE/N)

Network interface for the cameras.

DS-7600NI-SE/P

No.

Item

Description

1

LAN Network Interface

Connector for LAN (Local Area Network).

Quick Operation Guide of DS-7600NI-SE&V(P) Series NVR

7

2

RS-485 Interface

Connects to RS-485 devices.

3

Power Supply

100~240VAC power supply

4

Power Switch

Switch for turning on/off the device.

5

USB Interface

Universal Serial Bus (USB) ports for additional devices such as USB
mouse and USB Hard Disk Drive (HDD).

6

GND

Ground (needs to be connected when NVR starts up).

7

HDMI Interface

HDMI video output connector.

8

VGA Output

DB9 connector for VGA output. Display local video output and menu.

9

Audio In

RCA connector for voice talk input

10

Audio Out

RCA connector for audio output

11

Network Interfaces with
PoE function
(for DS-7600NI-SE/P)

Network interface for the cameras and to provide power over Ethernet.

DS-7600NI-V DS-7600NI-VP

No.

Item

Description

1

Power Switch

Switch for turning on/off the device.

2

LAN Network Interface

Connector for LAN (Local Area Network).

3

Audio In

RCA connector for voice talk input

4

GND

Ground (needs to be connected when NVR starts up).

5

Audio Out

RCA connector for audio output

6

HDMI Interface

HDMI video output connector.

7

VGA Output

DB9 connector for VGA output. Display local video output and menu.

8

Power Supply

100~240VAC power supply

9

USB Interface

Universal Serial Bus (USB) ports for additional devices such as USB
mouse and USB Hard Disk Drive (HDD).

10

Network Interfaces with
PoE function
(for DS-7600NI-VP)

Network interface for the cameras and to provide power over Ethernet.

Quick Operation Guide of DS-7600NI-SE&V(P) Series NVR

8

Specifications

Specifications of DS-7600NI-SE

Model

DS-7604NI-SE

DS-7608NI-SE

DS-7616NI-SE

Video/Audio
input

IP video input

4-ch

8-ch

16-ch

Two-way audio
input

1-ch, RCA (2.0 Vp-p, 1kΩ)

Bandwidth
Incoming

bandwidth

20Mbps

40Mbps

80Mbps

Output

bandwidth

40Mbps

Video/Audio
output

Decoding
resolution

5MP/3MP/1080p/UXGA/720p/VGA/4CIF/DCIF/
2CIF/CIF/QCIF

HDMI/VGA
output

1-ch, resolution:
1920 × 1080P /60Hz, 1600 × 1200 /60Hz, 1280 × 1024 /60Hz, 1280 ×
720 /60Hz, 1024 × 768 /60Hz

CVBS

1-ch, BNC (1.0 Vp-p, 75 Ω)
Resolution: 704 × 576 (PAL); 704 × 480 (NTSC) (optional)

Audio output

1-ch, RCA (Linear, 1kΩ).

Playback
resolution

5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF /QCIF

Synchronous
playback

4-ch, 720P / 2-ch,
1080P / 1-ch, 5MP

8-ch 4CIF /4-ch, 720P / 2-ch, 1080P / 1-ch,
5MP

Hard disk
SATA

1 SATA interface for
1 HDD

2 SATA interfaces for 2 HDDs

Capacity

Up to 4TB for each disk

External
interface

Network
interface

1 RJ-45 10 /100 /1000 Mbps self-adaptive Ethernet interface

Serial interface

1 RS-485 half-duplex interface

USB interface

2 × USB 2.0

Alarm in/out

4/1 (optional)

Others

Power supply

12V DC

Consumption

≤ 10 W (without hard disk)

Working
temperature

-10 ºC ~ +55 ºC (14 ºF ~ 131 ºF )

Working
humidity

10 % ~ 90 %

Chassis

Stand-alone 1U
chassis

19-inch rack-mounted 1U chassis

Dimensions
(W × D × H)

315 × 230 × 45mm
(124.0 × 90.5 × 17.7
inch)

445 × 290 × 45mm (175.2 × 114.2 × 17.7 inch)

Weight

≤ 2 Kg (4.4 lb) (without hard disk)

Quick Operation Guide of DS-7600NI-SE&V(P) Series NVR

9

Specifications of DS-7600NI-SE/N

Model

DS-7604NI-SE/N

DS-7608NI-SE/N

DS-7616NI-SE/N

Video/Audio
input

IP video input

4-ch

8-ch

16-ch

Two-way audio
input

1-ch, RCA (2.0 Vp-p, 1kΩ)

Bandwidth
Incoming

bandwidth

20Mbps

40Mbps

80Mbps

Output

bandwidth

40Mbps

Video/Audio
output

Recording
resolution

5MP/3MP/1080p/UXGA/720p/VGA/4CIF/DCIF/2CIF/CIF/QCIF

HDMI/VGA
output

1-ch, resolution:
1920 × 1080P /60Hz, 1600 × 1200 /60Hz, 1280 × 1024 /60Hz, 1280 ×
720 /60Hz, 1024 × 768 /60Hz

CVBS

1-ch, BNC (1.0 Vp-p, 75 Ω)
Resolution: 704 × 576 (PAL); 704 × 480 (NTSC) (optional)

Audio output

1-ch, RCA (Linear, 1kΩ)

Playback
resolution

5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF /QCIF

Synchronous
playback

4-ch, 720P / 2-ch,
1080P / 1-ch, 5MP

8-ch 4CIF /4-ch, 720P / 2-ch, 1080P / 1-ch,
5MP

Hard disk
SATA

1 SATA interface

2 SATA interfaces

Capacity

Up to 4TB for each disk

External
interface

Network
interface

1 RJ-45 10 /100 /1000 Mbps self-adaptive Ethernet interface

4 independent 10 /100
Mbps Ethernet
interfaces (for built-in
switch)

8 independent 10 /100 Mbps Ethernet interfaces
(for built-in switch)

Serial interface

1 RS-485 half-duplex interface

USB interface

2 × USB 2.0

Alarm in/out

4/1 (optional)

Others

Power supply

12 VDC

Consumption

≤ 15 W (without hard disk)

Working
temperature

-10 ºC ~ +55 ºC (14 ºF ~ 131 ºF)

Working
humidity

10 % ~ 90 %

Chassis

Stand-alone 1U
chassis

19-inch rack-mounted 1U chassis

Dimensions
(W × D × H)

315 × 230 × 45mm
(124.0 × 90.5 × 17.7
inch)

445 × 290 × 45mm (175.2 × 114.2 × 17.7 inch)

Weight

≤ 2 Kg (4.4 lb) ( without hard disk)

Quick Operation Guide of DS-7600NI-SE&V(P) Series NVR

10

Specifications of DS-7600NI-SE/P

Model

DS-7604NI-SE/P

DS-7608NI-SE/P

DS-7616NI-SE/P

Video/Audio input
IP video input

4-ch

8-ch

16-ch

Two-way audio
input

1-ch, RCA (2.0 Vp-p, 1kΩ)

Bandwidth

Incoming

bandwidth

20Mbps

40Mbps

80Mbps

Output

bandwidth

40Mbps

Video/Audio
output

Decoding
resolution

5MP/3MP/1080p/UXGA/720p/VGA/4CIF/DCIF/2CIF/CIF/QCIF

HDMI/VGA
output

1-ch, resolution:
1920 × 1080P /60Hz, 1600 × 1200 /60Hz, 1280 × 1024 /60Hz, 1280 ×
720 /60Hz, 1024 × 768 /60Hz

CVBS

1-ch, BNC (1.0 Vp-p, 75 Ω)
Resolution: 704 × 576 (PAL); 704 × 480 (NTSC) (optional)

Audio output

1-ch, RCA (Linear, 1kΩ)

Playback
resolution

5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF /QCIF

Synchronous
playback

4-ch, 720P / 2-ch,
1080P / 1-ch, 5MP

8-ch 4CIF /4-ch, 720P / 2-ch, 1080P / 1-ch,
5MP

Hard disk
SATA

2 SATA interfaces for 2 HDDs

Capacity

Up to 4TB for each disk

External interface

Network
interface

1 RJ-45 10 /100 /1000 Mbps self-adaptive Ethernet interface

4 independent 10 /100 Mbps PoE Ethernet interfaces

Serial interface

1 RS-485 half-duplex interface

USB interface

2 × USB 2.0

Alarm in/out

4/1 (optional)

Others

Power supply

100~240VAC, 47~63Hz, 3A

Consumption

≤ 15 W (without hard disk)

Working
temperature

-10 ºC ~ +55 ºC (14 ºF ~ 131 ºF)

Working
humidity

10 % ~ 90 %

Chassis

19-inch rack-mounted 1U chassis

Dimensions
(W × D × H)

445 × 290 × 45mm (175.2 × 114.2 × 17.7 inch)

Weight

≤ 2 Kg (4.4 lb) ( without hard disk)

Quick Operation Guide of DS-7600NI-SE&V(P) Series NVR

11

Specifications of DS-7600NI-V

Model

DS-7604NI-V

DS-7608NI-V

DS-7616NI-V

Video/Audio
input

IP video input

4-ch

8-ch

16-ch

Two-way audio
input

1-ch, RCA (2.0 Vp-p, 1kΩ)

Bandwidth

Incoming

bandwidth

20Mbps

40Mbps

80Mbps

Output

bandwidth

40Mbps

Video/Audio
output

Decoding
resolution

5MP/3MP/1080p/UXGA/720p/VGA/4CIF/DCIF/2CIF/CIF/QCIF

HDMI/VGA
output

1-ch, resolution:
1920 × 1080P /60Hz, 1600 × 1200 /60Hz, 1280 × 1024 /60Hz, 1280 ×
720 /60Hz, 1024 × 768 /60Hz

Audio output

1-ch, RCA (Linear, 1kΩ)

Playback
resolution

5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF /QCIF

Synchronous
playback

4-ch, 720P / 2-ch,
1080P / 1-ch, 5MP

8-ch 4CIF /4-ch, 720P / 2-ch, 1080P / 1-ch,
5MP

Hard disk
SATA

2 SATA interfaces for 2 HDDs

Capacity

Up to 4TB for each disk

External
interface

Network
interface

1 RJ-45 10 /100 /1000 Mbps self-adaptive Ethernet interface

Serial interface

1 RS-485 half-duplex interface

USB interface

2 × USB 2.0

Others

Power supply

12V DC

Consumption

≤ 10 W (without hard disk)

Working
temperature

-10 ºC ~ +55 ºC (14 ºF ~ 131 ºF)

Working
humidity

10 % ~ 90 %

Chassis

Vertical chassis

Dimensions
(W × D × H)

130 × 236 × 180mm (51.2 × 92.9 × 70.9 inch)

Weight

≤ 2 Kg (4.4 lb) ( without hard disk)

Quick Operation Guide of DS-7600NI-SE&V(P) Series NVR

12

Specifications of DS-7600NI-VP

Model

DS-7604NI-VP

DS-7608NI-VP

DS-7616NI-VP

Video/Audio
input

IP video input

4-ch

8-ch

16-ch

Two-way audio
input

1-ch, RCA (2.0 Vp-p, 1kΩ)

Bandwidth

Incoming

bandwidth

20Mbps

40Mbps

80Mbps

Video/Audio
output

Decoding
resolution

5MP/3MP/1080p/UXGA/720p/VGA/4CIF/DCIF/2CIF/CIF/QCIF

HDMI/VGA
output

1-ch, resolution:
1920 × 1080P /60Hz, 1600 × 1200 /60Hz, 1280 × 1024 /60Hz, 1280 ×
720 /60Hz, 1024 × 768 /60Hz

Audio output

1-ch, RCA (Linear, 1kΩ)

Playback
resolution

5MP /3MP /1080P /UXGA /720P /VGA /4CIF /DCIF /2CIF /CIF /QCIF

Synchronous
playback

4-ch, 720P / 2-ch,
1080P / 1-ch, 5MP

8-ch 4CIF /4-ch, 720P / 2-ch, 1080P / 1-ch,
5MP

Hard disk
SATA

2 SATA interfaces for 2 HDDs

Capacity

Up to 4TB for each disk

External
interface

Network
interface

1 RJ-45 10 /100 /1000 Mbps self-adaptive Ethernet interface

4 independent 10 /100 Mbps PoE Ethernet interfaces

Serial interface

1 RS-485 half-duplex interface

USB interface

2 × USB 2.0

Others

Power supply

100~240VAC, 47~63Hz, 3A

Consumption

≤ 15 W (without hard disk)

Working
temperature

-10 ºC ~ +55 ºC (14 ºF ~ 131 ºF)

Working
humidity

10 % ~ 90 %

Chassis

Vertical chassis

Dimensions
(W × D × H)

130 ×180 × 236 mm (51.2 × 92.9 × 70.9 inch)

Weight

≤ 2 Kg (4.4 lb) ( without hard disk)

Quick Operation Guide of DS-7600NI-SE&V(P) Series NVR

13

HDD Storage Calculation Chart

The following chart shows an estimation of storage space used based on recording at one channel for an hour at a
fixed bit rate.

Bit Rate

Storage Used

96K

42M

128K

56M

160K

70M

192K

84M

224K

98M

256K

112M

320K

140M

384K

168M

448K

196M

512K

225M

640K

281M

768K

337M

896K

393M

1024K

450M

1280K

562M

1536K

675M

1792K

787M

2048K

900M

Note: Please note that supplied values for storage space used is just for reference. Storage space used is estimated

by formulas and may have some deviation from actual value.

Quick Operation Guide of DS-7600NI-SE&V(P) Series NVR

14

Menu Operation

Menu Structure

Startup and Shutdown

Proper startup and shutdown procedures are crucial to expanding the life of the NVR.
To start your NVR:

1. Check the power supply is plugged into an electrical outlet. It is HIGHLY recommended that an

Uninterruptible Power Supply (UPS) be used in conjunction with the device. The Power indicator LED on
the front panel should be red, indicating the device gets the power supply.

2. Turn on the power switch on the rear panel to start the NVR immediately.

To shut down the NVR:

1. Enter the Shutdown menu.

Menu > Shutdown

Shutdown Menu

2. Select the Shutdown button.

3. Click the Yes button.

4. Shut the power switch down when the shutdown attention pops up.

Quick Operation Guide of DS-7600NI-SE&V(P) Series NVR

15

Using the Start Wizard

By default, the Setup Wizard starts once the NVR has loaded, as shown in Figure below.

Start Wizard Interface

Operating the Setup Wizard:

1. The Setup Wizard can walk you through some important settings of the NVR. If you don’t want to use the

Setup Wizard at that moment, click the Cancel button. You can also choose to use the Setup Wizard next
time by leaving the “Start wizard when NVR starts?” checkbox checked.

2. Click Next button on the Wizard window to enter the Login window.

Login Window

3. Enter the admin password. By default, the password is 12345.

4. To change the admin password, check the New Admin Password checkbox. Enter the new password and

confirm the password in the given fields.

5. Click the Next button to enter the date and time settings window.

Quick Operation Guide of DS-7600NI-SE&V(P) Series NVR

16

Date and Time Settings

6. After the time settings, click Next button which takes you back to the Network Setup Wizard window.

DS-7600NI-SE and DS-7600NI-V

DS-7600NI-SE/N, DS-7600NI-SE/P and DS-7600NI-VP

Network Configuration

Quick Operation Guide of DS-7600NI-SE&V(P) Series NVR

17

Note: For DS-7600NI-SE/N, DS-7600NI-SE/P and DS-7600NI-VP series NVR, the internal NIC IPv4 address

should be configured for the cameras connecting to the PoE network interface or the built-in switch of the NVR.

7. Click Next button after you configured the network parameters, which takes you to the HDD Management

window.

HDD Management

8. To initialize the HDD, click the Init button. Initialization removes all the data saved in the HDD.

9. Click Next button. You enter the Adding IP Camera interface.

10. Click Search to find online IP Camera. Select the IP camera to be added, and click the Add button.

Search for IP Cameras

11. Click Next button. Configure the recording for the searched IP Cameras.

Quick Operation Guide of DS-7600NI-SE&V(P) Series NVR

18

Record Settings

12. Click Copy to copy the settings to other channels.

Copy Record Settings

13. Click OK to complete the startup Setup Wizard.

Live View

Some icons are provided on screen in Live View mode to indicate different camera status. These icons include:

Live View Icons

In the live view mode, there are icons at the right top of the screen for each channel, showing the status of the
record and alarm in the channel, so that you can find problems as soon as possible.

Alarm (video loss, tampering, motion detection or sensor alarm).

Record (manual record, schedule record, motion detection or alarm triggered record)

Alarm & Record

Quick Operation Guide of DS-7600NI-SE&V(P) Series NVR

19

Adding and Configuring IP Cameras

You should add and configure the online IP cameras to enable the live view and recording function.

Adding IP Cameras

You can search and add the online IP cameras by following the startup wizard, or according to the following steps.

Steps:

1. Enter the Camera Management interface.

Menu> Camera> Camera

Main Menu

2. To add the online cameras with same network segment:

1) Click Search to search the online cameras.

Camera Settings Interface

2) Check the checkbox of certain cameras to be added.

3) Click Quick Add to add the camera.

3. To add other IP cameras:

1) On the left side of the interface, you can enter the IP address, protocol, management port, and other

information of the IP camera to be added.

2) Click Add to add the camera.

Note: If you check the Synchronize IP Camera checkbox, the default settings of the NVR for the IP

Quick Operation Guide of DS-7600NI-SE&V(P) Series NVR

20

camera is applied to the added camera.

Configuring Basic Parameters of IP Cameras

After the adding of the IP cameras, the basic information of the camera lists in the page, and you can configure the
basic setting of the IP cameras.

Steps:

1. Click the icon to edit the parameters; you can edit the IP address, protocol and other parameters.

Edit the Parameters

2. Click apply to save the settings and click OK to exit the editing interface.
To edit more parameters:

1. Click the Advance Set icon.

Network Configuration of the Camera

2. You can edit the network information and the password of the camera.

3. Click Apply to save the settings and click OK to exit the interface.
Explanation of the icons:

Edit basic parameters of the camera

Delete the IP camera

Get the live view of the camera

Quick Operation Guide of DS-7600NI-SE&V(P) Series NVR

21

PTZ Control

Follow the procedure to set the parameters for PTZ. The configuring of the PTZ parameters should be done before
you set the PTZ camera.
Before you start, please check that the PTZ and the NVR are connected properly through RS-485 interface.

PTZ Settings

Steps:

1. Enter the PTZ Settings interface.

Menu >Camera> PTZ

Camera Settings Interface

2. Choose the camera for PTZ setting next to Camera label.

3. Enter the parameters of the PTZ camera.

Note: All the parameters should be exactly the same as the PTZ camera parameters.

4. Click Copy if you want to configure same settings to other PTZ cameras.

5. Click the Apply button to save and exit the interface.

PTZ Control

In the Live View mode, you can press the PTZ Control button on the front panel or on the remote, or choose the

PTZ Control icon to enter the PTZ toolbar.

PTZ Control Bar

Quick Operation Guide of DS-7600NI-SE&V(P) Series NVR

22

Description of the PTZ toolbar icons

Icon

Description

Icon

Description

Icon

Description

Direction button and

the auto-cycle button

Zoom+, Focus+,

Iris+

Zoom-, Focus-, Iris-

The speed of the

PTZ movement

Light on/off

Wiper on/off

3D-Zoom

Image

Centralization

Preset
Patrol

Pattern Menu

Previous item

Next item

Start pattern/patrol

Stop the patrol or

pattern movement

Minimize

windows

Exit

Playback

Play back the record files of a specific channel in the live view menu. Channel switch is supported.

Instant playback by channel

Choose a channel under live view using the mouse and click the button in the shortcut operation menu.

Note: Only record files recorded during the past five minutes on this channel will be played back.

Instant Playback Interface

All-day Playback by channel

Steps:

1. Enter the All-day Playback menu.

Mouse: right click a channel in live view mode and select All-day Playback from the menu.

Quick Operation Guide of DS-7600NI-SE&V(P) Series NVR

23

Right-click Menu under Live View

Under multi-screen live view, record files of the top left channel (not masked) will be played back.

2. Playback management.

The toolbar in the bottom part of Playback interface can be used to control playing process.

All-day Playback Interface

The channel and time selection menu will display by moving the mouse to the right of the playback interface.
Just tick the channel or channels if you want to switch playback to another channel or execute simultaneous
playback of multiple channels.

Quick Operation Guide of DS-7600NI-SE&V(P) Series NVR

24

All-day Playback Interface with Channel List

Backup

Recorded files can be backed up to various devices, such as USB flash drives, USB HDDs or a DVD writer.
Steps:

1. Enter Video Export interface.

Choose the channel(s) you want to back up and click on the Search button.

Quick Export Interface

2. Enter Export interface, choose backup device and press Export button to start exporting.

Quick Export using USB1-1

Quick Operation Guide of DS-7600NI-SE&V(P) Series NVR

25

3. Check backup result.

Choose the record file in Export interface and press button to check it.

Checkup of Quick Export Result Using USB1-1

0202051030520