DS-7200H V I/H F I-SH Se ries D V R
USE R M A NUA L
User Manual of DS-7200HVI/HFI-SH Series DVR
1
+LNYLVLRQ1HWZRUN'LJLWDO9LGHR5HFRUGHU8VHU¶V0DQXDO
This manual, as well as the software described in it, is furnished under license and may be used or copied only in
accordance with the terms of such license. The content of this manual is furnished for informational use only, is subject
to change without notice, and should not be construed as a commitment by Hikvision Digital Technology Co., Ltd.
(Hikvision). Hikvision assumes no responsibility or liability for any errors or inaccuracies that may appear in the book.
Except as permitted by such license, no part of this publication may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical, recording, or otherwise, without the prior written
permission of Hikvision.
HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
REGARDING THE HIKVISION SOFTWARE. HIKVISION DOES NOT WARRANT, GUARANTEE, OR MAKE
ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE HIKVISION
SOFTWARE IN TERMS OF ITS CORRECTNESS, ACCURACY, RELIABILITY, CURRENTNESS, OR
OTHERWISE. THE ENTIRE RISK AS TO THE RESULTS AND PERFORMANCE OF THE HIKVISION
SOFTWARE IS ASSUMED BY YOU. THE EXCLUSION OF IMPLIED WARRANTIES IS NOT PERMITTED BY
SOME STATES. THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.
IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO
YOU FOR ANY CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES (INCLUDING DAMAGES FOR
LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, AND THE
LIKE) ARISING OUT OF THE USE OR INABILITY TO USE THE HIKVISION SOFTWARE EVEN IF HIKVISION
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGES, THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
User Manual of DS-7200HVI/HFI-SH Series DVR
2
Regulatory Information
F C C Information
F C C complianc e: This equipment has been tested and found to comply with the limits for a digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
F C C C onditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
E U Confor mity State ment
This product and - if applicable - the supplied accessories too are marked with "CE" and comply
therefore with the applicable harmonized European standards listed under the Low Voltage Directive
2006/95/EC, the EMC Directive 2004/108/EC.
2002/96/EC (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper recycling, return this product to your local
supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection
points. For more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted
municipal waste in the European Union. See the product documentation for specific battery
information. The battery is marked with this symbol, which may include lettering to indicate
cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier
or to a designated collection point. For more information see: www.recyclethis.info.
Desc ription on Lase r Spec ific ation
The optical disc drive such as DVD Super Multi (Double Layer) Drive 22X that is used in this computer is equipped
with laser. The classification label with the following sentence is affixed to the surface of the drive.
CLASS 1 LASER
PRODUCT TO IEC60825-1
LASER KLASSE 1
The drive with the above label is certified by the manufacturer that the drive complies with the requirement for laser
product on the date of manufacturing pursuant to article 21 of Code of Federal Regulations by the United States of
America, Department of Health & Human Services, Food and Drug Administration.
In other countries, the drive is certified to comply with the requirement pursuant to IEC 60825-1 and EN 60825-1 on
class 1 laser product.
This computer is equipped with the optical disc drive in the following list according to the model.
User Manual of DS-7200HVI/HFI-SH Series DVR
3
Safe ty Warnings and C autions
Please pay atte ntion to the following warnings and cautions :
Haza r dous Voltage may be p rese nt: Special measures and precautions must be
taken when using this device. Some potentials (voltages) on the device may present a
hazard to the user. This device should only be used by the Employees from our company
with knowledge and training in working with these types of devices that contain live circuits.
Powe r Supply H aza r dous Voltage : AC mains voltages are present within the power supply assembly.
This device must be connected to a UL approved, completely enclosed power supply, of the proper rated voltage
and current. N o us er se rvice able pa r ts ins ide the pow e r s upp ly.
Sys te m G rounding (Earthing): To avoid shock, ensure that all AC wiring is not exposed and that the
earth grounding is maintained. Ensure that any equipment to which this device will be attached is also connected
to properly wired grounded receptacles and are approved medical devices.
Powe r Connec t and Disconnec t: The AC power supply cord is the main
disconnect device to mains (AC power).The socket outlet shall be installed near the
equipment and shall be readily accessible.
Installation and M aintenance: Do not connect/disconnect any cables to or perform
installation/maintenance on this device during an electrical storm.
User Manual of DS-7200HVI/HFI-SH Series DVR
4
Powe r Cord Requi re me nts: The connector that plugs into the wall outlet must be a grounding-type male
plug designed for use in your region. It must have certification marks showing certification by an agency in your
region. The connector that plugs into the AC receptacle on the power supply must be an IEC 320, sheet C13,
female connector. See the following website for more information http://kropla.com/electric2.htm.
Lithium Batte ry: This device contains a Lithium Battery. There is a risk of
explosion if the battery is replaced by an incorrect type. Dispose of used batteries
DFFRUGLQJWRWKHYHQGRU¶VLQVWUXFWLRQVDQGLQDFFRUGDQFHZLWKORFDOHQYLURQPHQWDO
regulations.
Pe rchlorate M ate r ial: Special handling may apply. See
www.dtsc.ca.gov/hazardouswaste/perchlorate. This notice is required by California Code of Regulations, Title
22, Division 4.5, Chapter 33: Best Management Practices for Perchlorate Materials. This device includes a
battery which contains perchlorate material.
Taiwan batter y re cycling:
Please recycle batteries.
The rmal and Me chanical Injury: Some components such as heat sinks,
power regulators, and processors may be hot; care should be taken to avoid contact
with these components.
Elec tro M agne tic Inte rfe re nc e : This equipment has not been tested for compliance with emissions limits
of FCC and similar international regulations. This device is not, and may not be, offered for sale or lease, or sold,
or leased until authorization from the United States FCC or its equivalent in other countries has been obtained.
Use of this equipment in a residential location is prohibited. This equipment generates, uses and can radiate
radio frequency energy which may result in harmful interference to radio communications. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment on and off, the user is required to take measures to eliminate the interference or discontinue the use
of this equipment.
Le ad C ontent:
Please recycle this device in a responsible manner. Refer to local environmental
regulations for proper recycling; do not dispose of device in unsorted municipal
waste.
User Manual of DS-7200HVI/HFI-SH Series DVR
5
Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact
dealer.
This manual is applicable to DS-7204HVI-SH, DS-7208HVI-SH, DS-7216HVI-SH; DS-7204HFI-SH,
DS-7208HFI-SH and DS-7216HFI-SH series DVR.
This manual may contain several technically incorrect places or printing errors, and the content is subject to
change without notice. The updates will be added into the new version of this manual. We will readily improve
or update the products or procedures described in the manual.
User Manual of DS-7200HVI/HFI-SH Series DVR
6
Preventive and Cautionary T ips
Before connecting and operating your device, please be advised of the following tips:
Ensure unit is installed in a well-ventilated, dust-free environment.
Unit is designed for indoor use only.
Keep all liquids away from the device.
Ensure environmental conditions meet factory specifications.
Ensure unit is properly secured to a rack or shelf. Major shocks or jolts to the unit as a result of dropping it
may cause damage to the sensitive electronics within the unit.
Use the device in conjunction with an UPS if possible.
Power down the unit before connecting and disconnecting accessories and peripherals.
A factory recommended HDD should be used for this device.
Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or
equivalent type only. Dispose of used batteries according to the instructions provided by the battery
manufacturer.
User Manual of DS-7200HVI/HFI-SH Series DVR
7
Product Key Features
Gener al
z PAL/NTSC adaptive video inputs.
z H.264 video compression with high reliability and superior definition.
z Each channel supports dual-stream.
z Independent configuration for each channel, including resolution, frame rate, bit rate, image
quality, etc.
z Input and output video quality is configurable.
z Normal and event recording parameters configurable per individual camera.
z Encoding for both audio/video composite stream and video stream; audio and video
synchronization during composite stream encoding.
z Watermark technology.
Local Monito ring
z Simultaneous HDMI, VGA and CVBS outputs.
z HDMI/VGA output at up to 1920×1080P resolution.
z 1/4/6/8/9/16-division live view is supported, and the display sequence of screens is adjustable.
z Live view screen can be switched in group, and manual switch and automatic cycle view is also
provided, the interval of automatic cycle can be adjusted.
z Quick setting menu is provided for live view.
z The selected live view channel can be shielded.
z Motion detection, tamper-proof, video exception and video loss alarm functions.
z Privacy mask.
z Multiple PTZ protocols supported; setting and calling of PTZ preset, patrol and pattern.
z Zooming in by clicking the mouse and PTZ tracing by dragging mouse.
H D D Manage me nt
z 1 SATA hard disk can be connected to DS-7200HVI-SH and DS-7204HFI-SH, and 2 SATA hard
disks to DS-7208/7216HFI-SH, with a maximum of 4TB storage capacity for each disk.
z 8 network disks (8 NAS disks, or 7 NAS disks+1 IP SAN disk) can be connected.
z HDD group management.
z Support HDD standby function.
z HDD property: redundancy, read-only, read/write (R/W).
z HDD quota management; different capacity can be assigned to different channel.
Re cord ing and Pl aybac k
z Holiday recording schedule configuration.
z Normal and event video encoding parameters.
z Multiple recording types: manual, normal, and motion.
z 8 recording time periods with separated recording types.
z Pre-record and post-record for motion detection for recording, and pre-record time for schedule
and manual recording.
z Searching record files by event.
z Customization of tags, searching and playing back by tags.
z Locking and unlocking record files.
z Local redundant recording.
User Manual of DS-7200HVI/HFI-SH Series DVR
8
z Searching and playing back record files by channel number, recording type, start time, end time,
etc.
z Smart search for the selected area in the video.
z Zooming in when playback.
z Playing reversely.
z Support pause, speed up, speed down, skip forward, and skip backward when playback, locating
by dragging the mouse.
z Up to 4/8/16-ch synchronous playback at 4CIF resolution.
Bac kup
z Export video data by USB or SATA .storage device.
z Export video clips when playback.
z Management and maintenance of backup devices.
Ala r m and Exce ption
z Configurable arming time of alarm input/output.
z Alarm for video loss, motion detection, tampering, abnormal signal, video input/output standard
mismatch, illegal login, network disconnected, IP confliction, abnormal record, HDD error, and
HDD full, etc.
z Alarm event triggers full screen monitoring, audio alarm, notifying surveillance center and
sending email.
z Automatic restore when system is abnormal.
Othe r Local F unc tions
z Operable by mouse, or IR remote control.
z Three-level user management; admin user is allowed to create many operating accounts and define
their operating permission, which includes the limit to access any channel.
z Operation, exceptions and log recording and searching.
z Import and export of device configuration information.
Ne tw ork F unct ions
z 1 self-adaptive 10M/100M network interface.
z IPv6 is supported.
z TCP/IP protocol, PPPoE, DHCP, DNS, DDNS, NTP, SADP, SMTP, SNMP, UPnP, NFS, and
iSCSI are supported.
z TCP, UDP and RTP for unicast.
z Remote search, playback, download, locking and unlocking of the record files, and downloading
files broken transfer resume.
z Remote parameters setup; remote import/export of device parameters.
z Remote viewing of the device status, system logs and alarm status.
z Remote locking and unlocking of control panel and mouse.
z Remote HDD formatting and program upgrading.
z Remote system restart.
z RS-485 transparent channel transmission.
z Alarm event and exception information can be sent to the remote host.
z Remotely start/stop recording.
z Upgrade by remote FTP server.
z Remote PTZ control.
z Two -way audio and voice broadcasting.
User Manual of DS-7200HVI/HFI-SH Series DVR
9
z Embedded WEB server.
De ve lop ment Sc alabil ity:
z SDK for Windows and Linux system.
z Source code of application software for demo.
z Development support and training for application system.
User Manual of DS-7200HVI/HFI-SH Series DVR
10
TABLE&OF&CONTENTS&
Product Key Features ............................................................................................................ 7!
C H A P T E R 1 .. .. .. .. . .. .. .. .. .. .. ... .. .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. . 14!
Introduction .. .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. 14!
1.1 Front Panel .................................................................................................................... 15!
1.2 IR Remote Control Operations ...................................................................................... 16!
1.3 USB Mouse Operation .................................................................................................. 18!
1.4 Input Method Description ............................................................................................. 18!
1.5 Rear Panel ..................................................................................................................... 20!
1.6 Starting Up and Shutting Down the Device .................................................................. 21!
C H A P T E R 2 .. .. .. .. . .. .. .. .. .. .. ... .. .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. . 23!
Getting Started .. .. .. . .. .. .. .. .. .. ... .. .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. 23!
C H A P T E R 3 .. .. .. .. . .. .. .. .. .. .. ... .. .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. . 28!
Live View.. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. .. ... . 28!
3.1 Introduction of Live View ............................................................................................. 29!
3.2 Operations in Live View Mode ..................................................................................... 30!
3.2.1 Using the Mouse in Live View .......................................................................... 30!
3.2.2 Using an Auxiliary Monitor ............................................................................... 31!
3.2.3 Quick Setting Toolbar in Live View Mode ........................................................ 31!
3.3 Adjusting Live View Settings ........................................................................................ 34!
3.4 Channel-zero Encoding ................................................................................................. 36!
3.5 User Logout................................................................................................................... 37!
C H A P T E R 4 .. .. .. .. . .. .. .. .. .. .. ... .. .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. . 38!
PT Z Controls . .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. .. 38!
4.1 Configuring PTZ Settings ............................................................................................. 39!
4.2 Setting PTZ Presets, Patrols & Patterns ........................................................................ 39!
4.2.1 Customizing Presets ........................................................................................... 39!
4.2.2 Calling Presets .................................................................................................... 40!
4.2.3 Customizing Patrols ........................................................................................... 41!
4.2.4 Calling Patrols .................................................................................................... 43!
4.2.5 Customizing Patterns ......................................................................................... 44!
4.2.6 Calling Patterns .................................................................................................. 45!
4.3 PTZ Control Toolbar ..................................................................................................... 46!
C H A P T E R 5 .. .. .. .. . .. .. .. .. .. .. ... .. .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. . 47!
Record Settings . .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. .. . .. .. .. .. .. .. ... .. . 47!
5.1 Configuring Encoding Parameters ................................................................................ 48!
5.2 Configuring Record Schedule ....................................................................................... 50!
5.3 Configuring Motion Detection Record ......................................................................... 54!
5.4 Manual Record .............................................................................................................. 57!
5.5 Configuring Holiday Record ......................................................................................... 58!
5.6 Configuring Redundant Record .................................................................................... 61!
5.7 Configuring HDD Group for Record ............................................................................ 62!
User Manual of DS-7200HVI/HFI-SH Series DVR
11
5.8 Files Protection ............................................................................................................. 64!
C H A P T E R 6 .. .. .. .. . .. .. .. .. .. .. ... .. .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. . 67!
Playback .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. .. . .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. 67!
6.1 Playing Back Record Files ............................................................................................ 68!
6.1.1 Playing Back by Channel ................................................................................... 68!
6.1.2 Playing Back by Time ........................................................................................ 71!
6.1.3 Playing Back by Normal Video Search .............................................................. 72!
6.1.4 Playing Back by Event Search ........................................................................... 75!
6.1.5 Playing Back by Tag .......................................................................................... 78!
6.1.6 Playing Back by System Log ............................................................................. 82!
6.2 Auxiliary Functions of Playback ................................................................................... 84!
6.2.1 Playing Back Frame by Frame ........................................................................... 84!
6.2.2 Smart Search ...................................................................................................... 84!
6.2.3 Digital Zoom ...................................................................................................... 86!
C H A P T E R 7 .. .. .. .. . .. .. .. .. .. .. ... .. .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. . 88!
Bac kup .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. .. . .. .. .. .. .. .. ... .. .. .. .. .. .. .. ... 88!
7.1 Backing up Record Files ............................................................................................... 89!
7.1.1 Quick Export ...................................................................................................... 89!
7.1.2 Backing up by Normal Video Search ................................................................. 91!
7.1.3 Backing up by Event Search .............................................................................. 94!
7.1.4 Backing up Video Clips ..................................................................................... 97!
7.2 Managing Backup Devices ........................................................................................... 99!
C H A P T E R 8 .. .. .. .. . .. .. .. .. .. .. ... .. .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. . 103!
Alarm Se ttings .. .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. .. 103!
8.1 Setting Motion Detection ............................................................................................ 104!
8.2 Detecting Video Loss .................................................................................................. 107!
8.3 Detecting Video Tampering......................................................................................... 108!
8.4 Handling Exceptions ................................................................................................... 109!
8.5 Setting Alarm Response Actions ................................................................................. 110!
C H A P T E R 9 .. .. .. .. . .. .. .. .. .. .. ... .. .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. . 111!
Network Settings .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. . .. .. .. .. .. .. ... .. .. .. . 111!
9.1 Configuring General Settings ...................................................................................... 112!
9.2 Configuring Advanced Settings .................................................................................. 112!
9.2.1 Configuring PPPoE Settings ............................................................................ 112!
9.2.2 Configuring DDNS .......................................................................................... 113!
9.2.3 Configuring NTP Server .................................................................................. 116!
9.2.4 Configuring SNMP .......................................................................................... 116!
9.2.5 Configuring UPnP ........................................................................................ 117!
9.2.6 Configuring Remote Alarm Host ..................................................................... 118!
9.2.7 Configuring Multicast ...................................................................................... 119!
9.2.8 Configuring RTSP ............................................................................................ 120!
9.2.9 Configuring Server and HTTP Ports ................................................................ 120!
9.2.10 Configuring Email .......................................................................................... 121!
9.3 Checking Network Traffic ........................................................................................... 124!
User Manual of DS-7200HVI/HFI-SH Series DVR
12
9.4 Network Detection ...................................................................................................... 125!
9.4.1 Testing Network Delay and Packet Loss ......................................................... 125!
9.4.2 Exporting Network Packet ............................................................................... 125!
9.4.3 Checking Network Status ................................................................................. 127!
9.4.4 Checking Network Statistics ............................................................................ 128!
C H A P T E R 1 0 .. .. .. .. . .. .. .. .. .. .. ... .. .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... 129!
H D D Management .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. .. . .. .. .. .. .. .. ... .. .. .. .. .. .. .. . .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. . 129!
10.1 Initializing HDDs ...................................................................................................... 130!
10.2 Managing Network HDD .......................................................................................... 132!
10.3 Managing HDD Group .............................................................................................. 135!
10.3.1 Setting HDD Groups ...................................................................................... 135!
10.3.2 Setting HDD Property .................................................................................... 136!
10.4 Configuring Quota Mode .......................................................................................... 138!
10.5 Checking HDD Status ............................................................................................... 140!
10.6 Checking S.M.A.R.T. Information ............................................................................ 141!
10.7 Configuring HDD Error Alarms ................................................................................ 142!
C H A P T E R 11 .. .. .. .. . .. .. .. .. .. .. ... .. .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... . 143!
Came ra Settings .. .. .. ... .. .. .. .. .. .. . .. .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. 143!
11.1 Configuring OSD Settings ........................................................................................ 144!
11.2 Configuring Privacy Mask ........................................................................................ 145!
11.3 Configuring Video Parameters .................................................................................. 146!
C H A P T E R 1 2 .. .. .. .. . .. .. .. .. .. .. ... .. .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... 147!
Devic e M anage me nt and Mainte nance . .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. . 147!
12.1 Viewing System Information .................................................................................... 148!
12.1.1 Viewing Device Information .......................................................................... 148!
12.1.2 Viewing Camera Information......................................................................... 148!
12.1.3 Viewing Record Information ......................................................................... 148!
12.1.4 Viewing Network Information ....................................................................... 149!
12.1.5 Viewing HDD Information ............................................................................ 149!
12.2 Searching & Exporting Log Files ............................................................................. 151!
12.3 Importing/Exporting Configuration Files .................................................................. 153!
12.4 Upgrading System ..................................................................................................... 155!
12.4.1 Upgrading by Local Backup Device .............................................................. 155!
12.4.2 Upgrading by FTP .......................................................................................... 155!
12.5 Restoring Default Settings ........................................................................................ 157!
C H A P T E R 1 3 .. .. .. .. . .. .. .. .. .. .. ... .. .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... 158!
Othe rs . .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. .. . .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. . 158!
13.1 Configuring General Settings .................................................................................... 159!
13.2 Configuring DST Settings ......................................................................................... 160!
13.3 Configuring More Settings ........................................................................................ 161!
13.4 Managing User Accounts .......................................................................................... 162!
13.4.1 Adding a User ................................................................................................ 162!
13.4.2 Deleting a User ............................................................................................... 164!
13.4.3 Editing a User ................................................................................................. 165!
User Manual of DS-7200HVI/HFI-SH Series DVR
13
13.4.4 Changing Password of Admin........................................................................ 166!
13.5 Logging out/Shutting down/Rebooting Device ......................................................... 167!
C H A P T E R 1 4 .. .. .. .. . .. .. .. .. .. .. ... .. .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... 168!
Appe ndix .. .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. .. .. .. .. .. .. ... .. .. .. .. .. .. . .. .. .. .. 168!
Glossary ............................................................................................................................ 169!
FA Q ................................................................................................................................... 170!
User Manual of DS-7200HVI/HFI-SH Series DVR
14
C H A P T E R 1
Introduction&
User Manual of DS-7200HVI/HFI-SH Series DVR
15
1. 1 F ront Pane l
The front panel of DS-7200HVI-SH/DS-7200HFI-ST series is shown in Figure 1.1.
!"#$%&'()('!%*+,'-.+&/'
0.1/&'()('2&34%"5,"*+'*6'7*+,%*/'-.+&/'8$,,*+3' '
No.
Name
Function D esc r iption
1
PO WER
POWER indicator turns green when DVR is powered up.
2
STAT US
STATUS indicator lights in red when HDD is reading/writing.
3
Tx/ Rx
Tx/Rx indictor blinks green when network connection is functioning
properly.
4
USB I nte rf ac e
Connects USB mouse or USB flash memory devices.
5
IR Rec eive r
Receiver for IR remote.
User Manual of DS-7200HVI/HFI-SH Series DVR
16
1. 2 IR Remote Control Ope rations
The device may also be controlled with the included IR remote control, shown in Figure 1.2.
Note :
Batteries (2×AAA) must be installed before operation.
!"#$%&'()9':&;*,&'7*+,%*/'
0.1/&'()9'2&34%"5,"*+'*6',<&'=:':&;*,&'7*+,%*/'8$,,*+3'
No.
Name
De sc ri ption
1
PO WER
Power on/off the device.
2
D E V
Enables/Disables Remote Control.
3
Alpha numer ic Buttons :
Switching to the corresponding channel in Live view or PTZ Control
mode.
Inputting numbers and characters in Edit mode.
Switching between different channels in All-day Playback mode.
4
E D I T Bu tton
Editing text fields. When editing text fields, it will also function as a
Backspace button to delete the character in front of the cursor.
On checkbox fields, pressing the EDIT button will
tick
the checkbox.
In Playback mode, it can be used to generate video clips for backup.
5
A B utton
Switching between input methods (upper and lowercase alphabet,
symbols and numeric input).
6
R E C Button
Entering the Manual Record settings menu.
User Manual of DS-7200HVI/HFI-SH Series DVR
17
No.
Name
De sc ri ption
In PTZ control settings, press the REC button and then you can call a
PTZ preset by pressing Numeric button.
7
PL AY B utton
Entering the All-day Playback menu.
8
IN F O Button
Reserved.
9
V O IP Button
Selecting all items on the list;
In live view or playback mode, it can be used to switch between main
and spot video output.
10
M EN U B ut ton
Back to the Main menu (after successful login).
Pressing and holding the button for 5 seconds will turn off audible key
beep.
11
PR E V B utton
Switching between single screen and multi-screen mode.
12
DIR E C T IO N/ E N TE R
Buttons
Navigating between different fields and items in menus.
In Playback mode, the Up and Down button are used to speed up and
slow down recorded video.
The Left and Right button will select the next and previous day of
recordings.
In live view mode, these buttons can be used to cycle through channels.
13
PT Z B utton
Enter the PTZ Control mode.
14
ESC Button
Back to the previous menu
Pressing for arming/disarming the DVR in Live View mode.
15
R E SE R VE D
Reserved.
16
F1 B utton
Selecting all items on the list when used in a list field.
In PTZ Control mode, it will turn on/off PTZ light.
17
PT Z Cont rol Buttons
Adjusting the iris, focus and zoom of a PTZ camera.
18
F2 B utton
Cycle through tab pages.
T rouble shooting Re mote Contr ol :
Note :
Make sure you have installed batteries properly in the remote control. And you have to aim the remote
control at the IR receiver on the front panel.
If there is no response after you press any button on the remote, follow the procedure below to troubleshoot.
Ste ps:
1. Go to Menu > Settings > General > More Settings by operating the mouse.
2. Check and remember device ID#. The default ID# is 255. This ID# is valid for all the IR remote controls.
3. Press the DEV button on the remote control.
4. Enter the device ID# from step 2.
5. Press the ENTER button on the remote.
If the remote control is operating properly, but there is still no response from the remote, please check the
following:
1. Batteries are installed correctly and the polarities of the batteries are not reversed.
2. Batteries are fresh and not out of charge.
3. IR receiver is not obstructed.
,IWKHUHPRWHVWLOOFDQ¶WIXQFWLRQSURSHUO\SOHDVHFKDQJHDUHPRWHDQGWU\DJDin, or contact the device provider.
User Manual of DS-7200HVI/HFI-SH Series DVR
18
1. 3 USB Mouse Ope ration
A regular 3-button (Left/Right/Scroll-wheel) USB mouse can also be used with this device. To use a USB
mouse:
1. Plug USB mouse into one of the USB interfaces on the front panel of the device.
2. The mouse should automatically be detected. If in a rare case that the mouse is not detected, the possible
reason may be that the two devices are not compatible, please refer to the recommended device list from
your provider.
The operation of the mouse:
0.1/&' ( )>'2&34%"5,"*+'*6',<&'?*$3&'7*+,%*/'
Name
Action
De sc ri ption
Left-Click
Single-Click
Live view: Select channel and show the quick set menu.
Menu: Select and enter.
Double-Click
Live view: Switch single-screen and multi-screen.
Click and Drag
PTZ control: pan, tilt and zoom.
Tamp er-proof, privacy mask and motion detection: Select target area.
Digital zoom-in: Drag and select target area.
Live view: Drag channel/time bar.
Right-Click
Single-Click
Live view: Show menu.
Menu: Exit current menu to upper level menu.
Scroll-Wheel
Scrolling up
Live view: Previous screen.
Right-click Menu: Previous item.
Scrolling down
Live view: Next screen.
Right-click Menu: Next item.
1. 4 Input Method Desc ription
!"#$%&'()>'@*6,'A&B1*.%C'
Description of the buttons on the soft keyboard:
0.1/&'()D'2&34%"5,"*+'*6',<&'@*6,'A&B1*.%C'=4*+3'
Icons
Description
Icons
Description
English
Capital English
Numbers
Symbols
User Manual of DS-7200HVI/HFI-SH Series DVR
19
Lowercase/Uppercase
Backspace
Space
Enter Exit
User Manual of DS-7200HVI/HFI-SH Series DVR
20
1. 5 Rear Panel
The rear panels of DS-7200HVI-SH/DS-7200HFI-SH series are shown in Figure 1.4, Figure 1.5 and Figure 1.6.
!"#$%&'()D':&.%'-.+&/'*6'2@EF9GDHI=JH!=E@H'
!"#$%&'()K':&.%'-.+&/'*6'2@EF9(L'HI=E@H'
Note:
The rear panel of DS-7208HVI-SH provides 8 video input interfaces.
!"#$%&'()L':&.%'-.+&/'*6'2@EF9(LH!=E@H'
Note:
The rear panel of DS-7208HFI-SH provides 8 video input interfaces.
0.1/&'()K'2&34%"5,"*+'*6':&.%'-.+&/'
No.
Ite m
De sc ri ption
1
V I D EO I N
BNC connector for analog video input.
2
V I D EO O UT
BNC connector for video output.
3
USB I nte rf ac e
Connects USB mouse or USB flash memory devices.
4
H D MI
HDMI video output.
5
V G A
DB15 connector for VGA output. Display local video output and menu.
6
A U D I O IN
RCA connector for audio input.
7
A U D I O O U T
RCA connector for audio output.
8
L A N I nte rface
Connector for LAN (Local Area Network).
9
RS-485 Inter fac e
Connector for RS-485 devices. Connect the D+ and D- terminals to T+
and T- of PTZ receiver respectively.
10
12V
12VDC power supply.
11
PO WER
Switch for turning on/off the device.
12
G N D
Ground(needs to be connected when DVR starts up)
User Manual of DS-7200HVI/HFI-SH Series DVR
21
1. 6 Starting Up and Shutting Down the Device
Purpose:
Proper startup and shutdown procedures are crucial to expanding the life of the device.
Before you start :
Check that the voltage of the extra power supply is the same with the GHYLFH¶V requirement, and the ground
connection is working properly.
Starting u p t he devic e:
Steps:
1. Check the power supply is plugged into an electrical outlet. It is HIGHLY recommended that an
Uninterruptible Power Supply (UPS) be used in conjunction with the device.
2. Press the P O W E R button on the rear panel. The Power indicator LED should turn green indicating that
the unit begins to start up.
Shu tting down the de vice :
Steps :
1. Enter the Shutdown menu.
Menu > Shutdown
!"#$%&'()F'@<$,C*M+'?&+$'
2. Click the Shutdown button to enter the following dialog box:
!"#$%&'()N'2"./*#'8*O'6*%'@<$,C*M+' ' '
3. Click the Y es button. The following message box pops up:
User Manual of DS-7200HVI/HFI-SH Series DVR
22
!"#$%&'()P'?&33.#&'8*O'6*%'-*M&%'Q66' ' '
4. Turn off the power switch on the rear panel of DVR.
Re boot ing the de vice
In the Shutdown menu (Figure 1.7), you can also click Re boot to reboot the device.
User Manual of DS-7200HVI/HFI-SH Series DVR
23
C H A P T E R 2
Getting&Started
User Manual of DS-7200HVI/HFI-SH Series DVR
24
The Setup Wizard can walk you through some important settings of the device. By default, the Setup Wizard
starts once the device has loaded.
Operating the Setup Wizard:
1. Select the system resolution from the drop-down menu. The default resolution is 1280×1024/60Hz.
Click Apply to save the resolution settings.
!"#$%&'9)('@,.%,'R"S.%C'=+,&%6.4&'
2. Check the checkbox to enable Setup Wizard when device starts. Click Ne xt to continue the setup wizard.
You can also click Cance l to exit the Setup Wizard, or use the Setup Wizard next time by leaving the
³6WDUWwL]DUGZKHQ'95VWDUWV"´FKHFNER[FKHFNHG and exit.
!"#$%&'9)9'@,.%,'R"S.%C'=+,&%6.4&'
3. Click N ex t button on the Wizard window to enter the L ogi n window, as shown in Figure 2.3.
1) Enter the admin password. By default, the password is 12345.
2) To change the admin password, check the New Admin Passwor d checkbox. Enter the new password
and confirm the password in the given fields.
User Manual of DS-7200HVI/HFI-SH Series DVR
25
!"#$%&'9)>'T*#"+'R"+C*M'
4. Click the N e x t button to enter the Date and T ime settings window, as shown in Figure 2.4.
Set the time zone, date format, system date and system time.
!"#$%&'9)D'2.,&'.+C'0";&'@&,,"+#3'
5. Click N ex t button which takes you back to the Network Setup Wizard window, as shown in Figure 2.5.
Set the network parameters, including the NIC type, IPv4 address, IPv4 subnet mask, default gateway, etc.
You can enable the DHCP to automatically obtain an IP address and other network settings from that
server.
User Manual of DS-7200HVI/HFI-SH Series DVR
26
!"#$%&'9)K'U&,M*%V'7*+6"#$%.,"*+' '''''
6. Click N ex t button to enter the H D D Manage me nt window, shown in Figure 2.6.
To initialize the HDD, click the Init button. Initialization removes all the data saved in the HDD.
!"#$%&'9)L'H22'?.+.#&;&+,'
7. Click N ex t button to enter the Record Se ttings window, as shown in Figure 2.7.
1) Select the camera to configure.
2) Check the checkbox to enable Sta r t Recording.
3) Select the recording mode to Normal or Motion Detection.
User Manual of DS-7200HVI/HFI-SH Series DVR
27
!"#$%&'9)F':&4*%C'@&,,"+#3'
4) Click C opy to copy the record settings of the current camera to other camera (s) if needed, as shown
in Figure 2.8.
!"#$%&'9)N'7*5B':&4*%C'@&,,"+#3' '
5) Click O K to return to the R e cor d Settings window.
8. Click O K to complete the startup Setup Wizard.
User Manual of DS-7200HVI/HFI-SH Series DVR
28
C H A P T E R 3
Live&View&
User Manual of DS-7200HVI/HFI-SH Series DVR
29
3. 1 Introduction of L ive Vie w
Live view shows you the video image getting from each camera in real time. The device automatically enters
Live View mode when powered on. It is also at the very top of the menu hierarchy, thus pressing the ESC many
WLPHVGHSHQGLQJRQZKLFKPHQX\RX¶UHRQEULQJs you to the Live View mode.
Live Vi ew I cons
In the live view mode, there are icons at the right top of the screen for each channel, showing the status of the
record and alarm in the channel, so that you can know whether the channel is recorded, or whether there are
alarms occur as soon as possible.
0.1/&'>)('2&34%"5,"*+'*6'T"W&'I"&M'=4*+3'
Ic ons
De sc ri ption
Alarm (video loss, tampering, motion detection or sensor alarm)
Record (manual record, schedule record, motion detection or alarm triggered record)
Alarm & Record
User Manual of DS-7200HVI/HFI-SH Series DVR
30
3. 2 O pe rations in Live Vie w Mode
In live view mode, the following functions can be realized:
Single Sc ree n: showing only one screen on the monitor.
M ul ti-sc ree n: showing multiple screens on the monitor simultaneously.
Auto-switch: the screen is auto switched to the next one. And you must set the dwell time for each screen
on the configuration menu before enabling the auto-switch.
Menu>Configuration>Live View>Dwell Time.
All-da y Playbac k: play back the recorded videos for current day.
Star t Reco rdi ng: start all-day normal recording or motion detection recording for all channels.
Aux/ M ain output sw itc h: the DVR will check the connection of the output interfaces to define the main
and auxiliary output interfaces. When both HDMI and VGA are connected, or either one is connected, it is
used as the auxiliary video output for live view, playback, recording and PTZ controls; When both HDMI
and VGA are not connected, it is used as the main video output for live view playback, recording, PTZ
control and menu operations.
When the aux output is enabled, you can do some basic operation on the live view mode for the Aux output,
while no operation is allowed for the main output.
3.2.1&Using&the&Mouse&in&Live&View&
In the live view mode, use the mouse to right-click on the window to access the following menu:
!"#$%&'>)(':"#<,E4/"4V'?&+$'
0.1/&'>)9'?*$3&'Q5&%.,"*+'"+'T"W&'I"&M'
Name
Description
Menu
Enter the main menu of the system by right clicking the mouse.
Single Screen
Switch to the single full screen by choosing channel number from the dropdown list.
Multi-screen
Adjust the screen layout by choosing from the dropdown list.
Previous Screen
Switch to the previous screen.
User Manual of DS-7200HVI/HFI-SH Series DVR
31
Next Screen
Switch to the next screen.
Start/Stop Auto-switch
Enable/disable the auto-switch of the screens.
Start Recording
Start all-day normal recording or motion detection recording for all channels.
Quick Set
Set the video output mode to Standard, Bright, Gentle or Vivid.
All-day Playback
Play back the video of the selected channel.
Aux Monitor
Switch to the auxiliary output mode and the operation for the main output is
disabled.
Note :
The
dwel l time
of the live view configuration must be set before using Start A uto-switch.
Note :
If you enter Aux monitor mode and the Aux monitor is not connected, the mouse operation is disabled;
you need to switch back to the Main output with the V O IP button and Ente r button on IR remote control.
Note :
If the corresponding camera supports intelligent function, the Reboot Intelligence option is included when
right-clicking mouse on this camera.
3.2.2&Using&an&Auxiliary&Monitor&
Certain features of the Live View are also available while in an Aux monitor. These features include:
Single Sc ree n: Switch to a full screen display of the selected camera. Camera can be selected from a
dropdown list.
M ul ti-sc ree n: Switch different display layout options. Layout options can be selected from a
dropdown list.
N e xt Sc re en: When displaying less than the maximum number of cameras in Live View, clicking this
feature will switch to the next set of displays.
P T Z: Enter PTZ Control mode.
M ai n M onitor : Enter Main operation mode.
Note :
In the live view mode of the main output monitor, the menu operation is not available while Aux output
mode is enabled.
3.2.3&Quick&Setting&Toolbar&in&Live&View&Mode&
On the screen of each channel, there is a quick setting toolbar which shows when you right-click mouse on the
camera.
!"#$%&'>)9'X$"4V'@&,,"+#3'0**/1.%
!
0.1/&'>)>'2&34%"5,"*+'*6'X$"4V'@&,,"+#'0**/1.%'=4*+3'
Ic ons
De sc ri ption
Ic ons
De sc ri ption
Ic ons
De sc ri ption
Enable Manual
Record
Instant Playback
/
Mute/Audio on
PTZ Control
Digital Zoom
Image Settings
Close
User Manual of DS-7200HVI/HFI-SH Series DVR
32
Instant Playback only shows the record in last five minutes. If no record is found, it means there is no
record during the last five minutes.
Digital Zoom can zoom in the selected area to the full screen. You can left-click and draw to select the area
for zooming in, as shown in Figure 3.3.
!"#$%&'>)>'2"#",./'Y**;
'
Image Settings icon can be selected to enter the Image Settings menu.
Steps :
1. Set the period of a day for configuring independent image parameters so as to satisfy different light
conditions, e.g., daylight and night time. Two periods can be configured. When you have configured
Period 1, the Period 2 is remained as the
Other Time
.
2. Select the mode from the drop-down menu according to different light conditions.
Four modes are selectable:
z Standard: in general lighting conditions (default).
z I ndoor : the image is relatively smoother.
z D im Light: the image is smoother than the other three modes.
z Out door: the image is relatively clearer and sharper. The degree of contrast and saturation is high.
!"#$%&'>)D'=;.#&'@&,,"+#3''
User Manual of DS-7200HVI/HFI-SH Series DVR
33
3. Adjust the image parameters including the brightness, contrast, saturation, hue and sharpness by moving
the sliding bar or increasing/decreasing the value.
Note :
The adjustable value range for the brightness, contrast, saturation and hue is 0~ 255 and for the
sharpness is 0~ 15.
4. Copy image parameters.
1) If you want to copy the image parameters of the current camera to other camera (s), click the C opy
button to enter the Copy to interface:
!"#$%&'>)K'7*5B'=;.#&'@&,,"+#3',*'Q,<&%'7.;&%.'Z3[''
2) Select the camera (s) to be configured with the image settings. You can also click the checkbox of
Analog to select all cameras.
3) Click the O K button to finish the Copy settings.
Note :
You can click the Res tore button to restore the current image settings to default parameters.
'
User Manual of DS-7200HVI/HFI-SH Series DVR
34
3. 3 A djusting Live View Settings
Purpose:
Live View settings can be customized according to different needs. You can configure the output interface,
dwell time for screen to be shown, mute or turning on the audio, the screen number for each channel, etc.
Ste ps:
1. Enter the Live View Settings interface.
Menu> Configuration> Live View
!"#$%&'>)L'T"W&'I"&ME\&+&%./
The settings available in this menu include:
Video Out put Int e rface : Select the output to configure the settings for. Two output interfaces
are selectable: VGA/HDMI and Main CVBS.
Live V ie w M ode: Select the display mode of live video to 1×1 or 2×2.
Dwell T ime : The time in seconds to
dwel l
between switching of channels when enabling
auto-switch in Live View.
Enable A udio O utput: Enable/disable audio output for the selected video output.
Notes:
1. When the VGA/HDMI output interface is used as the main video output and the Audio
Out put for the VGA/HDMI output interface is enabled, the VGA/HDMI audio and AUDIO
OUT can be used for live view, playback and two-way audio.
2. When the VGA/HDMI output is used as the main video output and the Audio Outp ut for
the VGA/HDMI output interface is disabled, the VGA/HDMI output provides no audio and
the AUDIO OUT is used for two-way audio.
3. When the CVBS output is used as the main video output, the VGA/HDMI audio is provided
for Aux video output in live view, and the AUDIO OUT is used as the main video output(for
live view, playback or two-way audio).
Eve nt O utput: Select the output to show event video.
Full Sc ree n M onitoring D well T ime : The time in seconds to show alarm event screen.
2. Setting Camera Order
User Manual of DS-7200HVI/HFI-SH Series DVR
35
!"#$%&'>)F'T"W&'I"&ME'7.;&%.'Q%C&%'
To set the camera order:
1) Click the V iew tab to enter the camera order settings interface.
2) Select the video output
3) Click the up and down button at each screen to select the channel you would like to display. Setting
DQµ;¶means the channel will not be displayed.
4) Click the A pply button to save the setting.
User Manual of DS-7200HVI/HFI-SH Series DVR
36
3. 4 C hanne l-ze ro Encoding
Purpose:
Sometimes you need to get a remote view of many channels in real time from web browser or CMS (Client
Management System) software, in order to decrease the bandwidth requirement without affecting the image
quality, channel-zero encoding is supported as an option for you.
Ste ps:
1. Enter the L i ve V iew Settings interface.
Menu> Configuration> Live View
2. Select the C hannel- Z e ro E ncodi ng tab.
!"#$%&'>)N'T"W&'I"&ME'7<.++&/EY&%*']+4*C"+#
3. Check the checkbox after E nab le Channel-Zer o E ncoding.
4. Configure the Frame Rate, Max. Bitrate Mode and Max. Bitrate.
After you set the Channel-Zero encoding, you can get a view in the remote client or IE browser of all the
channels in one screen.
User Manual of DS-7200HVI/HFI-SH Series DVR
37
3. 5 Use r Logout
Purpose:
After logging out, the monitor turns to the live view mode and if you want to do some operation, you need to
enter user name and password to log in again.
Ste ps:
1. Enter the Shutdown menu.
Menu>Shutdown
!"#$%&'>)P'@<$,C*M+'
2. Click L ogout.
Note :
After you have logged out the system, menu operation on the screen is invalid. It is required a user
name and password to login the system.
User Manual of DS-7200HVI/HFI-SH Series DVR
38
C H A P T E R 4
PTZ&Controls&
User Manual of DS-7200HVI/HFI-SH Series DVR
39
4. 1 Configuring P T Z Settings
Purpose:
Follow the procedure to set the parameters for PTZ. The configuring of the PTZ parameters should be done
before you control the PTZ camera.
Before you st art:
Check that the PTZ and the device are connected properly through RS-485 interface.
Ste ps:
1. Enter the PTZ Settings interface.
Menu>Camera>PTZ>General
!"#$%&'D)('-0YE'\&+&%. /' ' '
2. Choose the camera for PTZ setting in the C amer a dropdown list.
3. Enter the parameters of the PTZ camera.
Note :
All the parameters should be exactly the same as the PTZ camera parameters. Only PTZ Protocol
can be set for network cameras.
Example:
If the PTZ camera has a Baud rate as 115200, you should input 115200 in the Baud rate field.
4. Click C opy if you want to configure same settings to other PTZ cameras.
5. Click A ppl y button to save the settings.
4. 2 Setting PT Z Presets, Patrols & Patte rns
Before you st art:
Please make sure that the presets, patrols and patterns should be supported by PTZ protocols.
4.2.1&Customizing&Presets&
Purpose:
Follow the steps to set the Preset location which you want the PTZ camera to point to when an event takes
place.
Ste ps:
1. Enter the PTZ Control interface.
Menu>Camera>PTZ>More Settings
User Manual of DS-7200HVI/HFI-SH Series DVR
40
!"#$%&'D)9'-0YE'?*%&'@&,,"+#3
'
2. Use the directional button to wheel the camera to the location where you want to set preset.
3. Click the round icon before Save P rese t.
4. Click the preset number to save the preset.
Repeat the steps2-4 to save more presets. If the number of the presets you want to save is more than 17, you can
FOLFN>«@DQGFKRRVHWKHDYDLODEOHQXPEHUV
!"#$%&'D)>'?*%&'-%&3&,3'
4.2.2&Calling&Presets&
Purpose:
This feature enables the camera to point to a specified position such as a window when an event takes place.!
Call pr es et in the P T Z s etting inte rf ace :
Steps :
1. Enter the PTZ Control interface.
Menu>Camera>PTZ>More Settings
2. Check the round icon before C all Pre set.
User Manual of DS-7200HVI/HFI-SH Series DVR
41
!"#$%&'D)D'-0YE'7.//'-%&3&,'
3. Choose the preset number.
Call pr es et in live view mode :
Steps :
1. Click the PTZ Control icon in the quick setting bar to enter the PTZ setting menu in live view mode.
!"#$%&'D)K'-0Y'0**/1.%'
2. Choose Camer a in the list on the menu.
3. Choose preset in the Pre set list.
4.2.3&Customizing&Patrols&
Purpose:
Patrols can be set to move the PTZ to different key points and have it stay there for a set duration before moving
on to the next key point. The key points are corresponding to the presets. The presets can be set following the
steps above in
C ustomizing Prese ts
.
Ste ps:
1. Enter the PTZ Control interface.
User Manual of DS-7200HVI/HFI-SH Series DVR
42
Menu>Camera>PTZ>More Settings
2. Select patrol number.
3. Select the under Patrol option box to add key points for the patrol.
!"#$%&'D)L'-0YE'^CC'A&B'-*"+,'
4. Configure key point parameters, such as the key point No., duration of staying for one key point and speed
of patrol. The key point is corresponding to the preset. The Ke y Point No. determines the order at which
the PTZ will follow while cycling through the patrol. The D u ration refers to the time span to stay at the
corresponding key point. The Speed defines the speed at which the PTZ will move from one key point to
the next.
!"#$%&'D)F'A&B'5*"+,'7*+6"#$%.,"*+'
5. Click O K to save the key point to the patrol.
Repeat the above steps to add more key points.
You can also delete all the key points by clicking the trash icon
User Manual of DS-7200HVI/HFI-SH Series DVR
43
!"#$%&'D)N'A&B-*"+,3'2&/&,"*+'
4.2.4&Calling&Patrols&
Purpose:
Calling a patrol makes the PTZ to move according the predefined patrol path.
Calli ng patrol in the PT Z set ting in te r face :
Ste ps:
1. In the PTZ setting interface.
Menu> Camera> PTZ> More Settings
2. Select the patrol number, and then click to call the patrol.
3. Click to stop it.
!"#$%&'D)P'7.//"+#'-.,%*/'
Calli ng pr es et in li ve vie w mode :
Ste ps:
User Manual of DS-7200HVI/HFI-SH Series DVR
44
1. Press PTZ control on the IR remote, or click PTZ Control icon on the quick setting toolbar, to show
the PTZ control toolbar.
2. Choose Patrol on the control bar.
3. Click the patrol you want to call.
!"#$%&'D)(G'-0Y'0**/1.%E'-.,%*/'
4.2.5&Customizing&Patterns&
Purpose:
Patterns can be set by recording the movement of the PTZ. You can call the pattern to make the PTZ movement
according to the predefined path.
Ste ps:
1. Enter the PTZ Control interface.
Menu>Camera>PTZ>More Settings
2. Choose pattern number in the option box.
!"#$%&'D)(('-0YE'-.,,&%+'
3. Click , and use your mouse to drag the image or click the eight directional buttons in the control box
User Manual of DS-7200HVI/HFI-SH Series DVR
45
under the image to move the PTZ camera.
The movement of the PTZ is recorded as the pattern.
4. Click to save the pattern.
Repeat the above steps to save more patterns.
4.2.6&Calling&Patterns&
Purpose:
Follow the procedure to move the PTZ camera according to the predefined patterns.
Calli ng patte rn in the PT Z se tting inte rface
Ste ps:
1. Enter the PTZ Control interface.
2. Select the pattern number.
3. Click , then the PTZ moves according to the pattern. Click to stop it.
!"#$%&'D)(9'-0YE'7.//"+#'-.,,&%+'
Call pat ter n in live vie w mode .
Ste ps:
1. In the live view mode, press PTZ control on the IR remote control, or click PTZ Control icon on the
quick setting toolbar.
2. And then choose Patte rn on the control bar.
3. Double click the pattern number you want to call, or you can select the pattern number and click to
call the pattern.
!"#$%&'D)(>'-0Y'0**/1.%E'-.,,&%+!
User Manual of DS-7200HVI/HFI-SH Series DVR
46
4. 3 P T Z Control Toolbar
In the Live View mode, you can press the PTZ Control button on the IR remote control, or choose the PTZ
Control icon to enter the PTZ toolbar.
!"#$%&'D)(D'-0Y'0**/1.%'
0.1/&'D)('2&34%"5,"*+'*6',<&'-0Y',**/1.%'"4*+3'
Ic on
De sc ri ption
Ic on
De sc ri ption
Ic on
De sc ri ption
Direction button and the
auto-cycle button
Zoom+, Focus+,
Iris+
Zoom-, Focus-,
Iris-
The speed of the PTZ
movement
Light on/off
Wiper on/off
3D-Zoom
Image
Centralization
Preset
Patrol
Pattern
Menu
Previous item
Next item
Start
pattern/patrol
Stop the patrol or pattern
movement
Minimize
windows
Exit
User Manual of DS-7200HVI/HFI-SH Series DVR
47
C H A P T E R 5
Record&Settings&
User Manual of DS-7200HVI/HFI-SH Series DVR
48
5. 1 Configuring Encoding Parame ters
Purpose:
By configuring the encoding parameters you can define the transmission stream type, the resolution and so on.
Before you start :
1. Make sure that the HDD has already been installed. If not, please install a HDD and initialize it.
(Menu>HDD>General)
!"#$%&'K)('H22E'\&+&%. /'
2. Check the storage mode of the HDD
1) Click A dvanc e to check the storage mode of the HDD.
2) If the HDD mode is
Quota
, please set the maximum record capacity and maximum picture capacity.
For detailed information, see
Chapte r 10. 5 Configuring Quot a Mode
.
3) If the HDD mode is
Group
, you should set the HDD group. For detailed information, see
Chapter
5.9 Conf iguring H D D Group for Re cording
.
!"#$%&'K)9'H22E'^CW.+4&C' '
Steps:
1. Enter the Record settings interface to configure the encoding parameters:
Menu>Record>Encoding
User Manual of DS-7200HVI/HFI-SH Series DVR
49
!"#$%&'K)>']+4*C"+#'-.%.;&,&%3E?."+'@,%&.;'
2. Set encoding parameters for main stream
1) Select Re cord to enter the main stream settings interface.
2) Select the camera for configuration.
3) Configure the following parameters for the Main Stream (Normal) and the Main Stream (Event):
Stream Type : Set the stream type to be Video or Video & Audio.
Resol ut ion: Set recording at resolution of 4CIF, 2CIF, CIF or QCIF selectable.
B itrate Type: Set the bitrate type to be Variable or Constant.
V ideo Q uali ty: Set the video quality of recording, with 6 levels configurable.
F rame Rate: Set the frame rate of recording.
M ax. Bit r at e M ode: Set the mode to General or Customize (32-3072).
M ax B itrate (K bps): Select or customize the maximum bit rate for recording.
M ax. Bit r ate Range Re com me nded : A recommended Max. bitrate range is provided for
reference.
4) Configure the pre-record, post-record time, expired time, redundant record (this option is only
available when the HDD mode is
Group
) and whether you want to record audio.
Pre -record: The time you set to record before the scheduled time or event. For example, when
an alarm triggered the recording at 10:00, if you set the pre-record time as 5 seconds, the camera
records it at 9:59:55.
Post-reco rd: The time you set to record after the event or the scheduled time. For example,
when an alarm triggered the recording ends at 11:00, if you set the post-record time as 5 seconds,
it records till 11:00:05.
E xpi red Ti me : The expired time is the longest time for a record file to be kept in the HDD, if
the deadline is reached, the file will be deleted. You can set the expired time to 0, and then the
file will not be deleted. The actual keeping time for the file should be determined by the capacity
of the HDD.
Red undant Rec or d: Enabling redundant record means you save the record files in the
redundant HDD. See
Chapter 5.8 Configuring Redundant Record
.
Reco rd A udio: Check the checkbox to record the sound, or uncheck to record the image without
sound.
Not e :
The Re dundant R e cor d option is only available when the HDD mode is
Group.
The
User Manual of DS-7200HVI/HFI-SH Series DVR
50
redundant record is to decide whether you want the camera to save the record files in the redundant
HDD. You must configure the redundant HDD in HDD settings. For detailed information, see
Chapter 10.4.2 Sett ing H D D Property
.
5) If you want to copy the current main stream settings to other camera (s), click Copy to enter the
Copy Camera interface. Select the camera (s) and click O K to finish the copy settings.
!"#$%&'K)D'7*5B'7.;&%.'@&,,"+#3'
6) On the Record settings interface, click A pply to save the settings.
Note :
You can click the Restore button to restore the current main stream settings to the default
parameters.
3. Set encoding parameters for sub-stream
1) Click the Subst ream tab to enter the Substream settings interface.
!"#$%&'K)K']+4*C"+#'-.%.;&,&%3E@$1E3,%&.;'
2) Configure the parameters for the sub-stream. Refer to the step of main stream settings.
3) Click A pply to save the settings.
Note :
You can click the Restore button to restore the current sub-stream settings to the default parameters.
4) If you want to copy the current sub-stream settings to other camera (s), click Copy to enter the Copy
Camera interface. Select the camera (s) and click O K to finish the copy settings.
5. 2 Configuring Record Sc hedule
Purpose:
Set the record schedule, and then the camera automatically starts/stops recording according to the configured
User Manual of DS-7200HVI/HFI-SH Series DVR
51
schedule.
Ste ps:
1. Enter the Record Schedule interface.
Menu>Record>Schedule
2. Configure Record Schedule
1) Click Sche dule to enter the record schedule settings interface.
!"#$%&'K)L':&4*%C'@4<&C$/&'
2) Choose the camera you want to configure.
3) Check the check box after the Ena bl e Sc he dule item.
There are two ways to configure the record schedule.
Tas k 1: E dit the Sc he dule
Steps :
1) Click E di t.
2) In the message box, you can choose the day which you want to set schedule.
3) To schedule an all-day recording, check checkbox to enable all-day recording.
4) Set the Type in the dropdown list, including Normal and Motion.
Note :
To enable Motion triggered recording, you must configure the motion detection settings as
well. For detailed information, refer to
Chapte r 8.1
and
Chapter 8.2
.
!"#$%&'K)F']C",'@4<&C$/& '
5) To arrange other schedule, leave the A ll Day checkbox blank and set the Start/End time and Type.
Note :
Up to 8 periods can be configured for each day. And the time periods FDQ¶WEHRYHUODSSHG each other.
Repeat the above steps2)-5) to schedule recording for other days in the week. If the schedule can also be set to
User Manual of DS-7200HVI/HFI-SH Series DVR
52
other days, click C opy.
!"#$%&'K)N'7*5B'@4<&C$/&',*'Q,<&%'2.B3!
Note :
The Holi day option is available in the Schedule dropdown list when you have enabled holiday schedule
in Holiday se tt ings. Refer to C
hapte r 5.6 Configuring Holiday Record and Capture.
!"#$%&'K)'P'H*/"C.B'@&,,"+#3'
6) Click O K to save setting and back to upper level menu.
Tas k 2: Draw the Sc he du le
Steps :
1) Click the icon on the right to select a record type, including Normal, Motion and None.
Note :
To enable Motion triggered recording, you must configure the motion detection settings. For
detailed information, refer to
Chapte r 8.1
and
Chapter 8.2
.
2) Use the mouse to drag and draw time periods.
Note :
Up to 8 periods can be configured for each day.
!"#$%&'K)'(G'2%.M',<&'@4<&C$/&' '
User Manual of DS-7200HVI/HFI-SH Series DVR
53
3) You can repeat the above steps to set schedule for other channels. If the settings can also be used to
other channels, click Copy to enter the Copy Camera interface and then choose the channel to which
you want to copy.
!"#$%&'K)(('7*5B'@4<&C$/&',*'Q,<&%'7<.++&/3' '
4) Click Apply in the Record Schedule interface to save the settings.
User Manual of DS-7200HVI/HFI-SH Series DVR
54
5. 3 Configuring Motion Detec tion Record
Purpose:
Follow the steps to set the motion detection parameters. In the live view mode, once a motion detection event
takes place, the device can analyze it and do many actions to handle it. Enabling motion detection function can
trigger certain channels to start recording, or trigger full screen monitoring, audio warning, notify the
surveillance center and so on. In this chapter, you can follow the steps to schedule a record which triggered by
the detected motion.
Steps :
1. Enter the Motion Detection interface.
Menu>Camera>Motion
!"#$%&'K)(9'?*,"*+'2&,&4,"*+'
2. Configure Motion Detection:
1) Choose camera you want to configure.
2) Check the checkbox after E nable M ot ion D e tec tion.
3) Drag and draw the area for motion detection by mouse. If you want to set the motion detection for
all the area shot by the camera, click Full Sc ree n. To clear the motion detection area, click C lear.
!"#$%&'K)(>'?*,"*+'2&,&4,"*+E'?.3V'
4) Click H a ndling, and the message box for channel information will pop up.
User Manual of DS-7200HVI/HFI-SH Series DVR
55
!"#$%&'K)(D'?*,"*+'2&,&4,"*+'H.+C/"+#' '
5) Select the channels which you want the motion detection event to trigger recording.
6) Click A pply to save the settings.
7) Click OK to back to the upper level menu.
8) Exit the Motion Detection menu.
3. Enter Schedule settings interface.
Menu> Record> Schedule>Record Schedule
!"#$%&'K)(K':&4*%C'@4<&C$/&'
1) Check the checkbox after the E nable Schedule item.
2) Click E dit.
User Manual of DS-7200HVI/HFI-SH Series DVR
56
!"#$%&'K)(L']C",'@4<&C$/&E'?*,"*+'2&,&4,"*+'
3) In the message box, you can choose the day to which you want to set schedule.
4) Set the Type as Motion.
5) To schedule an all-day recording, check the checkbox after the All Day item.
!"#$%&'K)(F']C",'@4<&C$/&E'^//'2.B'
6) To arrange other schedule, leave the All D ay checkbox blank and set the Start/End time.
Note :
Up to 8 periods can be configured for each day. And the time periods FDQ¶WEHRYHUODSSHG
each other.
Repeat the above steps3)-6) to schedule motion detection triggered recording for all the week. If
the schedule can also be set to other days, click Copy.
User Manual of DS-7200HVI/HFI-SH Series DVR
57
!"#$%&'K)(N'7*5B'@4<&C$/&',*'Q,<&%'2.B3!
7) Click O K to back to upper level menu.
If you can to copy the same schedule settings to other camera (s), click Copy to enter the Copy Camera
interface, and then select the camera (s) you want to copy.
!"#$%&'K)(P'7*5B'@4<&C$/&',*'Q,<&%'7<.++&/3' '
5. 4 M anual Record
Purpose:
Follow the steps to set parameters for the manual record. When using manual record, you need to manually
cancel the record. The manual recording is prior to the scheduled recording.
Steps :
1. Enter the Manual settings interface.
Menu> Manual
User Manual of DS-7200HVI/HFI-SH Series DVR
58
!"#$%&'K)9G'?.+$./':&4*%C' '
2. Enable recording for camera (s).
Click the status button beside each camera number to change to , or you can enable recording
for all cameras by clicking the status bar before Analog to change it to .
3. Set recording mode to manual.
By default, the camera is enabled with recording by schedule ( ). Click the status bar to
change it to and click again to enable the recording to manual ( ).
: recording by schedule.
: recording by manual operation.
Note :
After rebooting, all the manual records enabled are canceled.
5. 5 Configuring Holiday Record
Purpose:
You may want to have different plan for recording on holiday. Follow the steps to configure the record schedule
on holiday for that year.
Steps :
1. Enter the Record setting interface.
Menu>Record
2. Choose H ol iday on the left bar.
!"#$%&'K)9('H*/"C.B'@&,,"+#3'
3. Enable Edit Holiday schedule.
1) Click to enter the Edit interface.
User Manual of DS-7200HVI/HFI-SH Series DVR
59
!"#$%&'K)99']C",'H*/"C.B'@&,,"+#3'
2) Check the checkbox after E nable .
3) Select Mode from the dropdown list.
There are three different modes for the date format to configure holiday schedule.
4) Set the start and end date.
5) Click A p pl y to save settings.
6) Click O K to exit the Edit interface.
4. Enter Record Schedule settings interface.
Menu> Record> Schedule
1) Select Record.
2) Check the checkbox after E nable Schedule.
3) Click E dit.
4) Select Holiday from the Sc he dul e dropdown list.
!"#$%&'K)9>']C",'@4<&C$/&E'H*/"C.B!
5) Select M otion from the Type dropdown list.
6) If you need all day recording, check the A ll Day checkbox. Otherwise leave it blank.
User Manual of DS-7200HVI/HFI-SH Series DVR
60
7) Set start/end time for holiday schedule.
Note :
Up to 8 periods can be configured for each day. And the time periods FDQ¶WEHRYHUODSSHG each other.
In the time table of the channel, both holiday schedule and normal day schedule are displayed.
Repeat the above steps4)-7) to set Holiday schedule for other channel. If the holiday schedule can also be used
to other channels, click Copy and choose the channel you want to apply the settings.
User Manual of DS-7200HVI/HFI-SH Series DVR
61
5. 6 Configuring Redundant Record
Purpose:
Enabling redundant recording, which means saving the record files not only in the R/W (read/write) HDD but
also in the redundant HDD, will effectively enhance the data safety and reliability.
Note :
You must set the Storage mode in the HDD advanced settings to Group before you set the HDD property
to Redundant. For detailed information, please refer to
Chapter 10.4 Managing H DD Group
. There should be at
least another HDD (NetHDD) which is in R/W mode.
Steps :
1. Enter HDD Information interface.
Menu> HDD
!"#$%&'K)9D'H22'\&+&%./'
2. Select the H DD and click to enter the Local HDD Settings interface.
1) Set the HDD property to Redundant.
!"#$%&'K)9K'H22'\&+&%./E]C","+#'
2) Click A pply to save the settings.
3) Click O K to back to the upper level menu.
3. Enter the Record setting interface.
Menu> Record> Encoding
1) Select Record.
User Manual of DS-7200HVI/HFI-SH Series DVR
62
!"#$%&'K)9L']+4*C"+#':&4*%C'
2) Select Camera you want to configure.
3) Check the checkbox of the Redunda nt R ec or d.
4) Click A pply to save settings and back to the upper level menu.
Repeat the above steps2)-4) for configuring other channels.
5. 7 Configuring HDD G roup for Record
Purpose:
You can group the HDDs and save the record files in certain HDD group.
Steps :
1. Enter HDD setting interface.
Menu>HDD
!"#$%&'K)9F'H22E\&+&%./'
2. Select A dvance d on the left bar.
Check whether the storage mode of the HDD is Group. If not, set it to Group. For detailed information,
please refer to
Chapter 10.4 Managing H D D G roup
.
3. Select G e ne ral in the left bar.
Click to enter editing interface.
4. Configuring HDD group.
1) Choose a group number for the HDD group.
2) Click A pply and then in the pop-up message box, click Yes to save your settings.
3) Click O K to back to the upper level menu.
Repeat the above steps3-4 to configure more HDD groups.
User Manual of DS-7200HVI/HFI-SH Series DVR
63
5. Choose the Channels which you want to save the record files in the HDD group.
1) Select A dva nc ed on the left bar.
!"#$%&'K)9N'H22E^CW.+4&C'
2) Choose Group number in the dropdown list of Record on H DD G roup .
3) Check the channels you want to save in this group.
4) Click A pply to save settings.
Note :
After having configured the HDD groups, you can configure the Recording settings
following the procedure provided in
Chapter 5.2-5. 6.
User Manual of DS-7200HVI/HFI-SH Series DVR
64
5. 8 Files Protec tion
Purpose:
You can lock the recorded files or set the HDD property to Read-only to protect the record files from being
overwritten.
Protec t file by loc ki ng the r e cor d file s:
Steps :
1. Enter Playback setting interface.
Menu> Playback
!"#$%&'K)9P'-/.B1.4V' '
2. Select the channels you want to investigate by checking the checkbox to .
3. Configure the record type, file type and start/end time.
4. Click Search to show the results.
!"#$%&'K)>G'-/.B1.4VE'@&.%4<':&3$/,'
5. Protect the record files.
User Manual of DS-7200HVI/HFI-SH Series DVR
65
1) Find the record files you want to protect, and then click the icon which will turn to ,
indicating that the file is locked.
Note :
The record files of which the recording is still not comSOHWHGFDQ¶WEHORFNHG
2) Click to change it to to unlock the file and the file is not protected.
!"#$%&'K)>('_+/*4V"+#'^,,&+,"*+'
Protec t file by se tting H D D prope rty to Re ad-only
Note :
To edit HDD property, you need to set the storage mode of the HDD to Group. See
Chapte r 10.4
Managing H DD G roup.
Steps :
1. Enter HDD setting interface.
Menu> HDD
!"#$%&'K)>9'H22'\&+&%./'
2. Click to edit the HDD you want to protect.
!"#$%&'K)>>'H22'\&+&%./E']C","+#'
3. Set the HDD to Read-only.
4. Click O K to save settings and back to the upper level menu.
User Manual of DS-7200HVI/HFI-SH Series DVR
66
Note :
<RX FDQ¶W VDYH DQ\ ILOHV LQ D 5HDG-only HDD. If you want to save files in the HDD, change the
property to R/W.
Note :
If there is only one HDD and is set to Read-only, the device FDQ¶W UHFRUG DQ\ ILOHV 2QO\ OLYHYLHZ
mode is available.
If you set the HDD to Read-only when the device is saving files in it, then the file will be saved in next R/W
HDD. If there is only one HDD, the recording will be stopped.
User Manual of DS-7200HVI/HFI-SH Series DVR
67
C H A P T E R 6
Playback&
User Manual of DS-7200HVI/HFI-SH Series DVR
68
6. 1 Playing Back Record Files
6.1.1&Playing&Back&by&Channel& &
Purpose:
Play back the recorded video files of a specific channel in the live view mode. Channel switch is supported.
Instant playback by c ha nne l:
Ste ps:
Choose a channel in live view mode using the mouse and click the button in the quick setting toolbar.
Note :
Only record files recorded during the last five minutes on this channel will be played back.
!"#$%&'L)'('=+3,.+,'-/.B1.4V'=+,&%6.4&'
All-da y Play bac k by channe l
1. Enter the All-day Playback interface.
Mouse: right click a channel in live view mode and select All-day Playback from the menu, as shown in
Figure 6.2.
User Manual of DS-7200HVI/HFI-SH Series DVR
69
!"#$%&'L)'9':"#<,E4/"4V'?&+$'$+C&%'T"W&'I"&M'
'
Press P L AY button on the IR remote control to play back record files of the channel under single-screen
live view.
Under multi-screen live view, record files of the top left channel (not masked) will be played back.
Note :
Pressing numerical buttons will switch playback to the corresponding channels during playback
process.
2. Playback management.
The toolbar in the bottom part of Playback interface can be used to control playing progress, as shown in
Figure 6.3.
!"#$%&'L)'>'^//EC.B'-/.B1.4V'=+,&%6.4&'
The channel and time selection menu displays by moving the mouse to the right of the playback interface.
Click the channel(s) if you want to switch playback to another channel or execute simultaneous playback of
multiple channels, as shown in Figure 6.4.
User Manual of DS-7200HVI/HFI-SH Series DVR
70
!"#$%&'L)'D'^//EC.B'-/.B1.4V'=+,&%6.4&'M",<'7<.++&/'T"3,' '
Dates marked in colors:
: No record files in this day.
: There is record file(s) in this day (not current day).
: There is only event recording file(s) in this day (not current day).
: Mouse cursor is located.
Figure 6. 5 Toolbar of All-day Playback
0.1/&'L)('2&,."/&C']O5/.+.,"*+'*6'^//EC.BE5/.B1.4V'0**/1.%'
Button
Ope ration
Button
Ope ration
Button
Ope ration
Button
Ope ration
/
Audio on /Mute
/
Start/Stop
clipping
30s forward
30s
reverse
Add default tag
Add customized
tag
Tag
management
Speed
down
/
Pause reverse
play/
Reverse play/
Single-frame
reverse play
/
Pause play/ Play/
Single-frame
play
Stop
Speed up
Previous day
Next day
Hide
Exit
Process bar
Video type bar
Notes:
1. Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to locate
special frames.
2. About video type bar: represents normal recording (manual or schedule); represents event recording
(motion, alarm, motion | alarm, motion & alarm).
User Manual of DS-7200HVI/HFI-SH Series DVR
71
6.1.2&Playing&Back&by&Time&
Purpose:
Play back video files recorded in specified time duration. Multi-channel simultaneous playback and channel
switch are supported.
Ste ps:
1. Enter playback interface.
Menu>Playback
2. Set search conditions and click the Playbac k button to enter Playback interface.
!"#$%&'L)L'I"C&*'@&.%4<'1B'0";&' ' '
In the Playback interface:
The toolbar in the bottom part of Playback interface can be used to control playing process, as shown in
Figure 6.7.
!"#$%&'L)F'=+,&%6.4&'*6'-/.B1.4V'1B'0";&'
User Manual of DS-7200HVI/HFI-SH Series DVR
72
!"#$%&'L)N'0**/1.%'*6'-/.B1.4V'1B'0";&'
0.1/&'L)9'2&,."/&C']O5/ .+.,"*+'*6'-/.B1.4VE1BE,";&'0**/1.%'
Button
Ope ration
Button
Ope ration
Button
Ope ration
Button
Ope rat ion
/
Audio
on/Mute
/
Start/Stop clipping
30s forward
30s
reverse
Add default
tag
Add customized tag
Tag
management
Speed
down
/
Pause reverse
play/Reverse
play/
Single-frame
reverse play
/
Pause
play/Play/Single-frame
play
Stop
Speed up
Video search Exit
Hide
Progress
bar
Video type
bar
Note :
1. Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to locate
special frames.
2. About video type bar: represents normal recording (manual or schedule); represents event recording
(motion, alarm, motion | alarm, motion & alarm).
6.1.3&Playing&Back&by&Normal&Video&Search&
Purpose:
Play back video files searched out by restricting recording type and recording time. The video files in the result
list are played back sequentially and channel switch is supported. Recording types contain Normal, Motion and
Manual.
Ste ps:
1. Enter Record File Search interface.
Menu>Playback
Set search condition and click Search button to enter the Search Result interface.
User Manual of DS-7200HVI/HFI-SH Series DVR
73
!"#$%&'L)P'U*%;./'I"C&*'@&.%4<' '
2. Choose a record file you want to play back.
If there is only one channel in the search result, clicking button takes you to Full-screen Playback
interface of this channel.
If more than one channel is optional, clicking button takes you to step 3 and step 4.
!"#$%&'L)'(G':&3$/,'*6'U*%;./'I"C&*'@&.%4<'
3. Choose channels for simultaneous playback.
Note :
Optional channels for simultaneous playback are the same as the channels chosen to search record
files in step 1. And the channel with the recorded file selected in step 2 is the main channel during
multi-channel playback and it is displayed at the upper left corner.
User Manual of DS-7200HVI/HFI-SH Series DVR
74
!"#$%&'L)'(('@&/&4,'7<.++&/3'6*%'@B+4<%*+*$3'-/.B1.4V' '
4. Synchronous Playback interface.
The toolbar in the bottom part of Playback interface can be used to control playing process.
!"#$%&'L)'(9'DE4<'@B+4<%*+*$3'-/.B1.4V'=+,&%6.4&'
The hidden list of recorded files displays by moving the mouse to the right of the playback interface.
User Manual of DS-7200HVI/HFI-SH Series DVR
75
!"#$%&'L)'(>'DE4<'@B+4<%*+*$3'-/.B1.4V'=+,&%6.4&'M",<'I"C&*'T"3,' '
!"#$%&'L)'(D'0**/1.%'*6'U*%;./'-/.B1.4V
'
0.1/&'L)>'2&,."/&C']O5/ .+.,"*+'*6'U*%;./'-/.B1.4V'0**/1.%'
Button
Ope ration
Button
Ope ration
Button
Ope ration
Button
Ope ration
/
Audio on/Mute
/
Start/Stop clipping
30s forward
30s reverse
Add default tag
Add customized tag
Tag
management
Speed down
/
Pause reverse
play/Reverse play/
Single-frame reverse
play
/
Pause
play/Play/Single-frame
play
Stop
Speed up
Previous file
Next file
Video search
Exit
Hide toolbar
Progress bar
Video type
bar
Note :
1. Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to locate
special frames.
2. About video type bar: represents normal recording (manual or schedule); represents event recording
(motion, alarm, motion | alarm, motion & alarm).
6.1.4&Playing&Back&by&Event&Search&
Purpose:
Play back record files on one or several channels searched out by restricting event type (motion detection).
Channel switch is supported.
Ste ps:
User Manual of DS-7200HVI/HFI-SH Series DVR
76
1. Enter the playback interface.
Menu>Playback
2. Select E vent tab to enter the Event Playback interface.
3. Select M ot ion as the event type.
4. Set the start time and end time of the record files.
5. Select the camera (s) for searching.
!"#$%&'L)'(K'I"C&*'@&.%4<'1B'?*,"*+
6. Click Search button to enter the Search Result interface.
The Pre-play and post-play can be configured. The Pr e-play refers to the time configured before the
defined start time of event search, and the Pos t-play refers to the time configured after the defined end
time of event search. For example, when the start time and end time of event search are set to
12:00 :00 -
13:00:00
, and the pre-play and post-play time is set to
30s
and
20s
respectively, then the actual playback
of event video file is
11:59:30 ~ 13:00:20
.
!"#$%&'L)'(L'I"C&*'@&.%4<':&3$/,'1B'?*,"*+
7. You can select an item from the list and click D e tails to view detailed information of the record file, e.g.
start time, end time, file size, etc.
User Manual of DS-7200HVI/HFI-SH Series DVR
77
!"#$%&'L)'(F']W&+,'2&,."/3'
'
8. Or you can directly click the button of each file item to enter its playback interface. The toolbar in the
bottom part of Playback interface can be used to control playing process.
!"#$%&'L)(N'=+,&%6.4& *6'-/.B1.4V'1B']W&+,'Z([
'
The hidden list of events will be displayed by moving the mouse to the right of the playback interface.
User Manual of DS-7200HVI/HFI-SH Series DVR
78
!"#$%&'L)'(P'=+,&%6.4& *6'-/.B1.4V'1B']W&+,'Z9[' '
'
!"#$%&'L)'9G'0**/1.%'*6'-/.B1.4V'1B']W&+,
'
0.1/&'L)D'2&,."/&C']O5/ .+.,"*+'*6'-/.B1.4VE1BE&W&+,'0**/1.%'
Button
Ope ration
Button
Ope ration
Button
Ope ration
Button
Ope ration
/
Audio on/Mute
/
Start/Stop clipping
30s forward
30s reverse
Add default tag
Add customized tag
Tag
management
Speed down
/
Pause reverse
play/Reverse play/
Single-frame reverse
play
/
Pause
play/Play/Single-frame
play
Stop
Speed up
Previous event
Next event
Event search
Exit
Hide
Progress bar
Video type
bar
Note :
1. Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to locate
special frames.
2. About video type bar: represents normal recording (manual or schedule); represents event recording
(motion, alarm, motion | alarm, motion & alarm).
6.1.5&Playing&Back&by&Tag&
Purpose:
User Manual of DS-7200HVI/HFI-SH Series DVR
79
Video tag allows you to record related information like people and location of a certain time point during
playback. You are also allowed to use video tag(s) to search for record files and position time point.
Before playing back by tag :
1. Enter Playback interface.
!"#$%&'L)'9('=+,&%6.4&'*6'-/.B1.4V'1B'0";&
'
Click button to add default tag.
Click button to add customized tag and input tag name.
Note :
Max. 64 tags can be added to a single video file.
2. Tag management.
Click button to check, edit and delete tag(s).
!"#$%&'L)'99'0.#'?.+.#&;&+,'=+,&%6.4&
'
Ste ps:
1. Enter Playback interface.
Menu>Playback
Click Tag tab to enter Playback by Tag interface.
Choose channels, tag type and time, and click Se ar c h to enter Search Result interface.
User Manual of DS-7200HVI/HFI-SH Series DVR
80
Note :
Two tag types are selectable:
All
and
Tag K eyword
. Input keyword if you choose
Tag K eyword
.
!"#$%&'L)'9>'I"C&*'@&.%4<'1B'0.#' '
2. Set playback conditions and tag management.
Choose the tag name of the recorded file you want to play back; it can be edited or deleted.
Pre-play and post-play time can be set according to actual needs.
Note :
Pre-play time and post-play time is added to the time point of the tag.
!"#$%&'L)'9D':&3$/,'*6'I"C&*'@&.%4<'1B'0.#
'
3. Playback by tag.
Choose a tag and click button to play back the related record file.
User Manual of DS-7200HVI/HFI-SH Series DVR
81
!"#$%&'L)'9K'=+,&%6.4&'*6'-/.B1.4V'1B'0.#
'
The hidden list of tags will be displayed by moving the mouse to the right of the playback interface.
!"#$%&'L)'9L'=+,&%6.4&'*6'-/.B1.4V'1B'0.#'M",<'I"C&*'T"3,
'
!"#$%&'L)'9F'0**/1.%'*6'-/.B1.4V'1B'0.#
'
0.1/&'L)K'2&,."/&C']O5/ .+.,"*+'*6'-/.B1.4VE1BE,.#'0**/1.%'
Button
Ope ration
Button
Ope ration
Button
Ope ration
Button
Ope ration
/
Audio on/Mute
/
Start/Stop clipping
30s forward
30s reverse
Add default tag
Add customized tag
Tag
management
Slow down
/
Pause reverse
play/Reverse play/
Single-frame reverse
play
/
Pause
play/Play/Single-frame
play
Stop
Speed up
User Manual of DS-7200HVI/HFI-SH Series DVR
82
Previous tag
Next tag
Tag search
Exit
Hide
Progress bar
Video type
bar
Note :
1. Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to
locate special frames.
2. About video type bar: represents normal recording (manual or schedule); represents event
recording (motion, alarm, motion | alarm, motion & alarm).
6.1.6&Playing&Back&by&System&Log&
Purpose:
Play back record file(s) associated with channels after searching system logs.
Ste ps:
1. Enter Log Search interface.
Menu>Maintenance>Log Search
!"#$%&'L)'9N'@B3,&;'T*#'@&.%4<'=+,&%6.4&'
'
2. Set search time and type and click Se a r c h button.
User Manual of DS-7200HVI/HFI-SH Series DVR
83
!"#$%&'L)'9P':&3$/,'*6'@B3,&;'T*#'@&.%4<
'
3. Choose a log with record file and click button to enter Playback interface.
Note :
If there is no record file at the time point of the log, the message box ³No result found´ZLOOSRSXS
The toolbar in the bottom part of Playback interface can be used to control playing process.
!"#$%&'L)'>G'=+,&%6.4&'*6'-/.B1.4V'1B'T*#
'
User Manual of DS-7200HVI/HFI-SH Series DVR
84
6. 2 A uxiliary Func tions of Playbac k
6.2.1&Playing&Back&Frame&by&Frame&
Purpose:
Play video files frame by frame, in order to check image details of the video when abnormal events happen.
Ste ps:
Go to Playback interface. If you choose playback of the record file: click button and until the speed
changes to
S
ingle
frame and one click on the playback screen represents playback of one frame. If you choose
adverse playback of the record file: click button and until the speed changes to
S
ingle
frame and
one click on the playback screen represents adverse playback of one frame. It is also feasible to use button
in toolbar.
6.2.2&Smart&Search&
Purpose:
In order to locate motion detection event easily and accurately in the playback progress bar, you are allowed to
analyze a certain area (scene) dynamically, and to get all of the related motion detection events that occurred in
this area.
Ste ps:
1. Go to All-day Playback interface and play the video.
!"#$%&'L)'>('=+,&%6.4&'*6'^//EC.B'-/.B1.4V
'
2. Right-click mouse and select Smart Sea r ch to go to analysis area selection interface.
User Manual of DS-7200HVI/HFI-SH Series DVR
85
!"#$%&'L)'>9':"#<,E4/"4V'?&+$'"+'^//EC.B'-/.B 1 . 4 V ' =+,&%6.4&'
3. You can click button to set the full screen as target searching area. After drawing area(s), click
button to execute smart search in this area.
Note :
Multi-area and full-screen searching modes are supported.
!"#$%&'L)>>'2%.M'^%&.'*6'@;.%,'@&.%4<
'
Results of intelligent analysis:
Video type bar:
: Normal record file;
: Event record file;
: Dynamic record file.
The hidden list of record files display when moving the mouse to the right of the playback interface.
User Manual of DS-7200HVI/HFI-SH Series DVR
86
!"#$%&'L)>D'@;.%,'@&.%4<':&3$/,'M",<'I"C&*'T"3,' '
!"#$%&'L)>K'0**/1.%'*6'@;.%,'@&.%4<'-/.B1.4V
'
0.1/&'L)L'2&,."/&C']O5/.+.,"*+'*6'@;.%,E3&.%4<E5/.B1.4V'0**/1.%'
Button
Ope ration
Button
Ope ration
Button
Ope ration
Button
Ope ration
/
Audio on/Mute
/
Start/Stop clipping
30s forward
30s reverse
Add default tag
Add customized tag
Tag
management
Slow down
/
Pause reverse
play/Reverse play/
Single-frame reverse
play
/
Pause
play/Play/Single-frame
play
Stop
Speed up
Previous smart search
result
Next smart search
result
Video search
Exit Hide
Progress bar
Video type
bar
Smart search
bar
Note :
1. Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to
locate special frames.
2. About video type bar: represents normal recording (manual or schedule); represents event
recording (motion, alarm, motion | alarm, motion & alarm).
6.2.3&Digital&Zoom&
Ste ps:
1. Right click the mouse on a channel under playback and choose Digital Zoom to enter Digital Zoom
User Manual of DS-7200HVI/HFI-SH Series DVR
87
interface.
2. Use the mouse to draw a red rectangle and the image within it will be enlarged up to 16 times.
!"#$%&'L)>L'2%.M'^%&.'6*%'2"#",./'Y**;
'
!"#$%&'L)>F':"#<,E4/"4V'?&+$'"+'-/.B1.4V'?*C&' '
Right-c lic k menu:
Note :
This menu differs slightly from one playback interface to another.
0.1/&'L)F'2&,."/&C']O5/.+.,"*+'*6':"#<,E4/"4V'?&+$'$+C&%'-/.B1.4V'
Button
Function
Switch camera for playback
Return to Search interface
Enter Digital Zoom interface
Smart Search against a specified area
Show & hide control interface
Return to Live View interface
User Manual of DS-7200HVI/HFI-SH Series DVR
88
C H A P T E R 7
Backup&
User Manual of DS-7200HVI/HFI-SH Series DVR
89
7. 1 Bac king up Record Files
Before you sta rt :
Please insert the backup device(s) into the device.
7.1.1&Quick&Export&
Purpose:
Export record files to backup device(s) quickly.
Ste ps:
1. Enter Video Export interface.
Menu>Export>Normal
!"#$%&'F)('X$"4V']O5*%,'=+,&%6.4&' ' '
2. Choose the channel(s) you want to back up and click Quic k E xport button.
Notes:
1. The time duration of record files on a specified channel cannot exceed 24 hours. Otherwise, the
message bo[³0D[KRXUVDUHDOORZHGIRUTXLFNH[SRUW´ZLOOSRSXS
2. 7KHQXPEHURIFKDQQHOVIRUV\QFKURQRXVH[SRUWFDQQRWH[FHHG2WKHUZLVHWKHPHVVDJHER[³Max.
4 channels are allowed for synchronous quick export´ZLOOSRSXS
User Manual of DS-7200HVI/HFI-SH Series DVR
90
!"#$%&'F)9'X$"4V']O5*%,'$3"+#'_@8(E(
3. In the Export interface, choose backup device and click Expor t button to start exporting.
Note :
Here we use USB Flash Drive and please refer to the next section Normal Backup for more backup
devices supported by the device.
4. Stay in the Exporting interface until all record files are exported to the USB flash drive.
!"#$%&'F)>']O5*%,'!"+"3<&C
'
5. Check backup result.
Choose the record file in Export interface and click button to check it.
Note :
The Player player.exe will be exported automatically during record file export.
!"#$%&'F)D'7<&4V$5'*6'X$"4V']O5*%,':&3$/,'_3"+#'_@8(E(
'
User Manual of DS-7200HVI/HFI-SH Series DVR
91
7.1.2&Backing&up&by&Normal&Video&Search&
Purpose:
The record files can be backup to various devices, such as USB devices (USB flash drives, USB HDDs, USB
writer) and SATA writer.
Bac kup using USB fl as h drives, USB H D Ds, US B writer and S A T A w r ite r
Ste ps:
1. Enter Export interface.
Menu>Export>Normal
!"#$%&'F)K'U*%;./'I"C&*'@&.%4<'6*%'8.4V$5' '
2. Set search conditions and click Se ar c h button to enter the search result interface.
3. Select record files you want to back up.
Click button to play the record file if you want to check it.
Check the checkbox before the record files you want to back up.
Note :
The size of the currently selected files is displayed in the lower-left corner of the window.
User Manual of DS-7200HVI/HFI-SH Series DVR
92
!"#$%&'F)L':&3$/,'*6'U*%;./'I"C&*'@&.%4<'6*%'8.4V$5
'
4. Export the record files.
Click Export button and start backup.
Note :
If the inserted device is not recognized:
Click the R e fres h button.
Reconnect device.
Check for compatibility from vendor.
You can also format USB flash drives or USB HDDs via the device. USB writer and SATA writer
cannot be formatted.
!"#$%&'F)F']O5*%,'1B'U*%;./'I" C&*'@&.%4<'$3"+#'_@8'!/.3<'2%"W&'
User Manual of DS-7200HVI/HFI-SH Series DVR
93
!"#$%&'F)'N']O5*%,'1B'U*%;./'I"C&*'@&.%4<'$3"+#'_@8'R%",&%'
'
Stay in the Exporting interface until all record files are exported with pop-XSPHVVDJHER[³([SRUW
finished´
!"#$%&'F)P']O5*%,'!"+"3<&C
'
5. Check backup result.
Choose the record file in Export interface and click button to check it.
Note :
The Player player.exe will be exported automatically during record file export.
!"#$%&'F)(G'7<&4V$5'*6']O5*%,':&3$/,'$3"+#'_@8'!/.3<'2%"W&'
User Manual of DS-7200HVI/HFI-SH Series DVR
94
!"#$%&'F)'(('7<&4V$5'*6']O5*%,':&3$/,'$3"+#'_@8'R%",&%'
' '
7.1.3&Backing&up&by&Event&Search&
Purpose:
Back up event-related record files using USB devices (USB flash drives, USB HDDs, USB writer), or SATA
writer. Quick Backup and Normal Backup are supported.
Steps :
1. Enter Export interface.
Menu>Export>Event
2. Select M ot ion as the event type.
3. Set the start time and end time of the record files.
4. Select the camera (s) for searching.
!"#$%&'F)(9']W&+,'@&.%4<'6*%'8.4V$5
5. Click Search button to enter the Search Result interface.
User Manual of DS-7200HVI/HFI-SH Series DVR
95
!"#$%&'F)(>':&3$/,'*6']W&+,'@&.%4<'
6. Select record files to export.
z Select motion detection event (s) from the list and click Quic k E xpor t button to enter the Export
interface, as shown in Figure 7.15.
z (1) Click the D e tails button to enter the interface with detailed information of the record file, e.g.,
start time, end time, file size, etc.
Note :
The size of the currently selected files is displayed in the lower-left corner of the window.
(2) Select record file (s) from the list and click Expor t button to enter the Export interface, as shown
in Figure 7.15.
!"#$%&'F)(D']W&+,'2&,."/3'=+,&%6.4&
'
7. Export the selected record files.
Click the Export button and start backing up.
Note :
If the inserted USB device is not recognized:
Click the Refresh button.
Reconnect device.
Check for compatibility from vendor.
User Manual of DS-7200HVI/HFI-SH Series DVR
96
You can also format USB flash drive or USB HDDs via the device.
!"#$%&'F)(K']O5*%,'1B']W&+,'_3"+#'_@8'!/.3<'2%"W&
'
Stay in the Exporting interface until all record files are exported with pop-XSPHVVDJH³([SRUWfinished´
!"#$%&'F)(L']O5*%,'!"+"3<&C
'
8. Check backup result.
Choose the record file in Export interface and click button to check it.
Note :
The Player player.exe will be exported automatically during record file export.
!"#$%&'F)(F'7<&4V$5'*6']W&+,']O5*%,':&3$/,'_3"+# '_@8'! /.3<'2%"W&
'
User Manual of DS-7200HVI/HFI-SH Series DVR
97
7.1.4&Backing&up&Video&Clips&
Purpose:
You may also select video clips to export directly during Playback, using USB devices (USB flash drives, USB
HDDs, USB writer), or SATA writer.
Ste ps:
1. Enter Playback interface.
Please refer to
Chapter 6
.
2. During playback, use buttons and in the playback toolbar to start or stop clipping record file(s).
3. Exit Playback interface after finishing clipping and you will then be prompted to save the clips.
Note :
A maximum of 30 clips can be selected for each channel.
!"#$%&'F)(N'=+,&%6.4&'*6'-/.B1.4V'1B'0";&
'
4. Click Y es to save video clips and enter Export interface, or click No to quit and do not save video clips.
!"#$%&'F)(P'^,,&+,"*+',*'I"C&*'7/"5'@.W"+#
'
5. Export the video clips.
Click Export button and start backing up.
Note :
If the inserted USB device is not recognized:
Click the Ref resh button.
Reconnect device.
Check for compatibility from vendor.
You can also format USB flash drive or USB HDDs via the device.
User Manual of DS-7200HVI/HFI-SH Series DVR
98
!"#$%&'F)9G']O5*%,'I"C&*'7/"53'_3"+#'_@8'!/.3<'2%"W&
Stay in the Exporting interface until all record files are exported with pop-XS PHVVDJH ³([SRUW
finished´
!"#$%&'F)9(']O5*%,'!"+"3<&C
'
6. Check backup result.
Note :
The Player player.exe will be exported automatically during record file export.
!"#$%&'F)99'7<&4V$5'*6'I"C&*'7/"53']O5*%,':&3$/,'_3"+#'_@8'!/.3<'2%"W&
'
User Manual of DS-7200HVI/HFI-SH Series DVR
99
7. 2 M anaging Bac kup Devices
M an age me nt of USB flas h drives, and US B H D Ds.
1. Enter Search Result interface of record files.
Menu>Export>Normal
Set search condition and click Se ar c h button to enter Search Result interface.
Note :
At least one channel shall be selected.
!"#$%&'F)9>'U*%;./'I"C&*'@&.%4<' '
2. Select record files you want to back up.
Click Export button to enter Export interface.
Note :
At least one record file shall be selected.
!"#$%&'F)9D':&3$/,'*6'U*%;./'I"C&* '@&.%4<'6*%'8.4V$5
Loading...