DS-3WF01C-2N/O User Guide
Wireless Bridge DS-3WF01C-2N/O
User Guide
i
DS-3WF01C-2N/O User Guide
User Guide
COPYRIGHT © 2019 Hangzhou Hikvision Digital Technology Co., Ltd.
ALL RIGHTS RESERVED.
Any and all information, including, among others, wordings, pictures, graphs are the properties of
Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be
“Hikvision”). This user manual (hereinafter referred to be “the Manual”) cannot be reproduced,
changed, translated, or distributed, partially or wholly, by any means, without the prior written
permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties,
guarantees or representations, express or implied, regarding to the Manual.
About this Manual
The Guide includes instructions for using and managing the product. Pictures, charts, images and
all other information hereinafter are for description and explanation only. The information
contained in the Guide is subject to change, without notice, due to firmware updates or other
reasons. Please find the latest version in the company website
(http://overseas.hikvision.com/en/).
Please use this user guide under the guidance of professionals.
Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are the properties of Hikvision in various
jurisdictions. Other trademarks and logos mentioned below are the properties of their respective
owners.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS
HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS,
AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,
MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND
NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS,
EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR
INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS,
BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE
USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY
AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL
OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER
ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL
PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR
JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS
THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS
USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER
PREVAILS.
i
DS-3WF01C-2N/O User Guide
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at
his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE" and
comply therefore with the applicable harmonized European standards listed under the
EMC Directive 2014/30/EU, the LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of
as unsorted municipal waste in the European Union. For proper recycling, return this
product to your local supplier upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more information see: www.recyclethis.info
2006/66/EC (battery directive): This product contains a battery that cannot be disposed
of as unsorted municipal waste in the European Union. See the product documentation
for specific battery information. The battery is marked with this symbol, which may
include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return
the battery to your supplier or to a designated collection point. For more information see:
www.recyclethis.info
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.
ii
DS-3WF01C-2N/O User Guide
Symbol
Description
Provides additional information to emphasize or supplement
important points of the main text.
Indicates a potentially hazardous situation, which if not avoided,
could result in equipment damage, data loss, performance
degradation, or unexpected results.
Indicates a hazard with a high level of risk, which if not avoided, will
result in death or serious injury.
Applicable Models
This guide is applicable to DS-3WF01C-2N/O.
Symbol Conventions
The symbols that may be found in this document are defined as follows.
During the installation and utilization of the device, please strictly conform to electrical safety
rules in different nations and regions.
You shall acknowledge that the use of the device with Internet access might be under network
security risks, please strengthen protection for your personal information and data security. If
you find the device might be under network security risks, please contact with us.
iii
DS-3WF01C-2N/O User Guide
Contents
Chapter 1 Application Scenario .................................................................................................. 1
1.1 Networking requirement ......................................................................................................... 1
1.2 Solution .................................................................................................................................... 1
1.3 Connecting the wireless bridges .............................................................................................. 1
1.3.1 Hardware connection of AP device .................................................................................. 1
1.3.2 Hardware connection of CPE device ................................................................................ 2
1.4 Networking topology ............................................................................................................... 3
Chapter 2 Login ......................................................................................................................... 4
2.1 Logging in to the web UI of the wireless bridge ...................................................................... 4
2.2 Logging out of the web UI of the wireless bridge .................................................................... 8
Chapter 3 System Status ............................................................................................................ 9
3.1 Device info ............................................................................................................................... 9
3.2 Information of peer device .................................................................................................... 10
Chapter 4 Network .................................................................................................................. 12
4.1 Overview ................................................................................................................................ 12
4.2 Changing the IP address ......................................................................................................... 13
Chapter 5 Wireless .................................................................................................................. 15
5.1 Overview ................................................................................................................................ 15
5.2 Changing wireless parameters ............................................................................................... 17
5.3 Scanning SSID nearby ............................................................................................................. 18
Chapter 6 System .................................................................................................................... 20
6.1 Maintenance .......................................................................................................................... 20
6.1.1 Device info ..................................................................................................................... 20
6.1.2 Maintenance .................................................................................................................. 20
6.1.3 Import/Export ................................................................................................................ 23
6.1.4 Upgrade .......................................................................................................................... 24
6.2 Time settings .......................................................................................................................... 26
6.2.1 Manual ........................................................................................................................... 26
6.2.2 Synchronize with the internet ....................................................................................... 26
6.3 Basic Service ........................................................................................................................... 27
6.3.1 SSH server ...................................................................................................................... 27
6.3.2 Export ............................................................................................................................. 29
6.4 Account .................................................................................................................................. 30
Appendix .................................................................................................................................... 31
A Default parameters ..................................................................................................................... 31
B Acronyms and Abbreviations ...................................................................................................... 32
iv
DS-3WF01C-2N/O User Guide
AP device
PoE injector
Switch
NVR
Monitor
Chapter 1 Application Scenario
1.1 Networking requirement
To ensure the safety of employees and property, a video surveillance system needs to be installed
in a building site.
1.2 Solution
The wireless bridges are used to address this requirement.
1.3 Connecting the wireless bridges
1.3.1 Hardware connection of AP device
Connect the AP device to a switch in monitor center. See the following figure:
1
DS-3WF01C-2N/O User Guide
CPE device
PoE injector
IP camera
1.3.2 Hardware connection of CPE device
Connect the CPE device to an IP camera in the monitoring site.
2
DS-3WF01C-2N/O User Guide
Switch
NVR
Monitor
Monitoring point
1.4 Networking topology
Select one scenario to install the wireless bridge to the corresponding site.
3
DS-3WF01C-2N/O User Guide
1
2
Chapter 2 Login
2.1 Logging in to the web UI of the wireless bridge
For initial use of the router, refer to the quick start guide of the wireless bridge to activate the
wireless bridge. After activating the wireless bridge, you can refer to the following procedure for
login.
Step 1 Connect a computer to the wireless bridge, or the switch connected to the wireless bridge.
Step 2 Configure the IP address of the computer used to configure the wireless bridge. OS
example: Windows 7
(1) Right-click the icon on the lower right corner of the desktop.
(2) Click Open Network and Sharing Center.
(3) Click Local Area Connection, then click Properties.
4
DS-3WF01C-2N/O User Guide
(4) Double-click Internet Protocol Version 4 (TCP/IPv4).
(5) Select Use the following IP address, set the IP address to 192.168.1.X (X ranges from 2 to
253, excluding 36), the Subnet mask to 255.255.255.0, and click OK.
(6) Click OK on the Local Area Connection Properties window, and close the other
windows.
5
DS-3WF01C-2N/O User Guide
Step 3 Log in to the web UI of the wireless bridge.
(1) Start a web browser, and visit 192.168.1.36.
If the following page appears, click Advanced.
Then click Proceed to 192.168.1.36 (unsafe).
6
DS-3WF01C-2N/O User Guide
----End
(2) Enter the login password you set before, and click Login.
7
DS-3WF01C-2N/O User Guide
Log in to the web UI successfully. Now you can configure the wireless bridge.
If the login page does not appear, try the following solution:
Check whether the wireless bridge is powered on properly, and the computer is connected to
the wireless bridge properly.
Check whether the IP address of the computer is set to 192.168.1.X (X ranges from 2 to 254,
excluding 36).
Reset the device and refer to the quick start guide to configure it again.
Reset method: After the device is powered on for about 1 minute, hold down the RST button
for about 8 seconds, then release it. When all the LED indicators light up, the device is restored
to factory settings.
2.2 Logging out of the web UI of the wireless bridge
Click the Logout on the upper-right corner of the web UI to logout. When you close the web
browser, the system logs you out as well.
8
DS-3WF01C-2N/O User Guide
Items
Description
Device Info
Device Name
It specifies the name of this device. If this device is not the only
one of its kind in the network, this name helps you identify the
device. You can change the name of this device on the
System > Maintenance page.
Model
It specifies the model number of this device.
Device SN
It specifies the serial number of this device. The devices in the
same package have the same serial number.
Firmware
It specifies the system software version number of this device.
Uptime
It specifies time during which this device is operating.
MAC Address
It specifies the MAC address of LAN port of this device. When
connecting to another device using an Ethernet cable, the
wireless bridge uses this MAC address to communicate with
the device.
Wireless
Operating Mode
It specifies the working mode the device operates. The wireless
Chapter 3 System Status
This module allows you to view the information of this wireless bridge and peer.
3.1 Device info
Log in to the web UI, and choose Status.
You can view the device info, wireless parameters and network parameters here.
Parameters Description
9
DS-3WF01C-2N/O User Guide
Items
Description
Parameters
bridge works in AP mode or CPE mode, and cannot be changed.
SSID
It specifies the wireless network name of this device.
Security Mode
It specifies the security mode of the wireless network of this
device.
Network Mode
It specifies the network mode of this device.
Channel Width
It specifies the bandwidth of the operating channel of a
wireless network.
Channel
It specifies channel in which this device operates, and its center
frequency.
Transmission Power
It specifies the transmit power of this device.
Higher number indicates wider WiFi coverage. Setting a proper
transmit power helps improve the performance and security of
the wireless network.
Network
Parameters
IP Address
It specifies the IP address (also named management IP address)
of this device. You can change this IP address on the Network
page.
Subnet Mask
It specifies the subnet mask of the wireless bridge.
Gateway
It specifies the default gateway of the wireless bridge. When
the device accessing the internet, packets should be forwarded
through the gateway.
DNS1
It specifies the primary DNS server IP address of the wireless
bridge.
DNS2
It specifies the secondary DNS server IP address of the wireless
bridge.
3.2 Information of peer device
Log in to the web UI, and choose Status > Peer Device.
You can view the transmitted and received rate of this wireless bridge, and view the related
information of peer device, such as signal strength, noise, IP address and MAC address.
10
Parameters Description
Items
Description
SN
It specifies the serial number of peer wireless bridge.
IPv4
It specifies the IP address of peer wireless bridge.
MAC Address
It specifies the MAC address of peer wireless bridge.
Signal Strength
It specifies the signal strength of peer wireless bridge.
Received Rate (Mbps)
It specifies the receiving rate of this wireless bridge.
Transmitted Rate
(Mbps)
It specifies the transmitting rate of this wireless bridge.
Noise (dBm)
It specifies the interference signal and electromagnet noise strength of peer
wireless device in the current environment. Larger absolute value indicates less
interference.
DS-3WF01C-2N/O User Guide
11
DS-3WF01C-2N/O User Guide
Items
Description
IP Address
It specifies the IP address (also named management IP address) of this device.
Devices in LAN can use it to log in to the web UI of this wireless bridge. If you want
to enable this wireless bridge to access the internet, this IP address should be set to
an unused IP address which is in the same segment as that of the egress router.
Subnet Mask
It specifies the subnet mask of the wireless bridge. The default is 255.255.255.0.
Gateway
It specifies the default gateway of this wireless bridge. It is optional.
If you want to enable this wireless bridge to access the internet, the gateway should
be set to the LAN IP address of the egress router.
Chapter 4 Network
4.1 Overview
Log in to the web UI, and choose Network.
You can change the network parameters of this wireless bridge here, including IP address, subnet
mask, gateway and DNS server addresses here.
Parameters Description
12
DS-3WF01C-2N/O User Guide
Items
Description
DNS1
It specifies the primary DNS server IP address of this wireless bridge. It is optional.
If you want to enable this wireless bridge to access the internet, and the egress
router supports DNS agent, you can enter the LAN IP address of the router here. If
the router does not support DNS agent, you need to enter a correct DNS IP address
here.
DNS2
It specifies the secondary DNS server IP address of this wireless bridge. It is
optional.
If you have two DNS server IP addresses, you can enter the other one here.
*
4.2 Changing the IP address
Assume that you need to change the IP address to 192.168.1.25.
Configuration procedure
Step 1 Choose Network.
Step 2 Change the IP Address to 192.168.1.25.
Step 3 Click Save.
----End
If you still want to configure the wireless bridge after changing the IP address, refer to the
following procedure:
13
DS-3WF01C-2N/O User Guide
If the new IP address is in the same network segment as that of the old one, refresh the page
and use the new IP address to log in to the web UI for configuration.
If the new IP address is in different network segment from that of the old one, set the IP
address of your management computer to an unused one which should be in the same
network segment as that of the new IP address of the wireless bridge. Then use the new IP
address of the wireless bridge to log in to the web UI for configuration.
14
DS-3WF01C-2N/O User Guide
Items
Description
Operating Mode
It specifies the working mode the device operates. The wireless bridge works in AP
mode or CPE mode, and cannot be changed.
SSID
It specifies the wireless network name of this device. You can change it here.
Chapter 5 Wireless
5.1 Overview
L
og in to the web UI, and choose Wireless.
You can change the wireless parameters of this wireless bridge here, including SSID, channel,
transmission power, and so on.
Parameters description
After changing the SSID of this wireless bridge, you need to change the SSID of peer
wireless bridge as well. Otherwise, the wireless bridge fails to connect to peer one.
15
DS-3WF01C-2N/O User Guide
Items
Description
Hide
It specifies whether to hide the SSID.
Check the Hide box: The wireless bridge does not broadcast this SSID. When
connecting to the wireless network, you need to enter the SSID manually.
Uncheck the Hide box: The wireless bridge broadcasts this SSID. Wireless
devices nearby can scan find the SSID.
Country Code
It specifies the country/region this wireless bridge locates. When you configure the
device for the first time, you need to select your country/region to activate the
device. It cannot be changed here.
Network Mode
It specifies the network mode of this device. Currently, it supports 11b/g/n, which
allows wireless devices supporting 802.11b, 802.11g, and 802.11n at 2.4 GHz band
to access the wireless network.
Channel Width
It specifies the bandwidth of the operating channel of a wireless network.
20MHz: The wireless bridge can only use 20 MHz channel bandwidth.
40MHz: The wireless bridge can only use 40 MHz channel bandwidth.
Channel
It specifies channel in which this device operates, and its center frequency. Auto
indicates the wireless bridge select the channel automatically according to the
current environment.
Antenna Gain
It specifies the built-in antenna gain value. It cannot be changed.
Transmission Power
It specifies the transmit power of this device. Larger transmission power indicates
wider WiFi coverage. Set a proper transmission power can improve the security and
performance of the wireless bridge.
Allowing adjusting
transmission power
If you want to change the transmission power of the wireless bridge, check this
option, and enter a value in the Transmission power input box.
Security Mode
It specifies the security mode of the wireless network of this device.
None: It indicates that any device can connect to the wireless network of the
device. For security, this option is not recommended.
WPA-PSK: It indicates that the wireless network uses WPA-PSK security mode.
WPA2-PSK: It indicates that the wireless network uses WPA2-PSK security
mode.
Security Key
It specifies the WPA pre-shared key.
Scan
It used to scan the wireless networks nearby, and displays their SSID, MAC address,
channel, signal strength, and so on for analysis.
16
DS-3WF01C-2N/O User Guide
5.2 Changing wireless parameters
Step 1 Choose Wireless.
Step 2 Change the parameters as required.
Step 3 Click Save.
----End
17
DS-3WF01C-2N/O User Guide
5.3 Scanning SSID nearby
Assume that you need to detect the wireless networks nearby.
Step 1 Choose Wireless.
Step 2 Click Scan.
----End
Wait until the scanning completes. You can set a channel with less interference which is less used
by the devices nearby to improve the wireless transmission performance.
18
DS-3WF01C-2N/O User Guide
19
DS-3WF01C-2N/O User Guide
Chapter 6 System
6.1 Maintenance
6.1.1 Device info
Log in to the web UI and choose System > Maintenance.
In this module, you can change the device name. If this device is not the only one of its kind in the
network, this name helps you identify the device.
Customize a device name in the Device Name input box, and click Save.
6.1.2 Maintenance
Log in to the web UI and choose System > Maintenance.
In this module, you can reboot, reset or partially reset the wireless bridge.
Partial Reset: After being reset partially, the wireless bridge is restored to the activated status,
and only network configurations and the login password are kept unchanged.
Reset: After being reset, the wireless bridge is restored to factory settings, and you need to
activate it again before configuration.
Reboot
If a setting does not take effect or the wireless bridge works improperly, you can try rebooting it to
resolve the problem.
Rebooting the device will disconnect all connections. So you’d better reboot it at idle time.
20
DS-3WF01C-2N/O User Guide
Configuration procedure
Step 1 Choose System > Maintenance.
Step 2 Click Reboot.
Step 3 Confirm the message on the pop-up window, and click OK.
----End
A progress bar is displayed on the page. Wait for it to elapse.
Partial reset
If you want to reset the wireless bridge to activated status, and keep network parameters and
login password unchanged, you can partial reset the device.
Configuration procedure
Step 1 Choose System > Maintenance.
Step 2 Click Partial Reset.
Step 3 Confirm the message on the pop-up window, and click OK.
21
DS-3WF01C-2N/O User Guide
----End
A progress bar is displayed on the page. Wait for it to elapse.
Reset
If you cannot locate a fault of the wireless bridge or forget the login password, you can restore the
wireless bridge to factory settings and then configure it again.
When the factory settings are restored, the configuration of the wireless bridge is lost. Therefore, you need
to reconfigure it. Restore the factory settings of the wireless bridge only when necessary.
To prevent damaging the wireless bridge, ensure that the power supply of the wireless bridge is normal
during reset.
Configuration procedure
Step 1 Choose System > Maintenance.
Step 2 Click Reset.
Step 3 Confirm the message on the pop-up window, and click OK.
22
DS-3WF01C-2N/O User Guide
----End
A progress bar is displayed on the page. Wait for it to elapse.
6.1.3 Import/Export
Log in to the web UI and choose System > Maintenance.
The Export function enables you to export the current configuration of the wireless bridge to a
local computer. The Import function enables you to import the wireless bridge to a previous
configuration.
If the wireless bridge enters the optimum condition after you greatly change the configuration of
the wireless bridge, you are recommended to export the configuration, so that you can import it
after upgrading or resetting the wireless bridge.
If you need to apply same or similar configurations to many wireless bridges, you can configure
one of the wireless bridges, export its configuration, and use the Import function to import the
configuration on the other wireless bridges. This improves configuration efficiency.
Export
Step 1 Choose System > Maintenance.
Step 2 Click Export.
----End
A file with a name of “APCfm,cfg” will be saved to your local computer.
23
DS-3WF01C-2N/O User Guide
If the following warning message appears, click Keep.
Import
Step 1 Choose System > Maintenance.
Step 2 Click Browser.
Step 3 Select a configuration file you export before, and click Import.
Step 4 Confirm the message on the pop-up window, and click OK.
----End
A progress bar is displayed on the page. Wait for it to elapse.
6.1.4 Upgrade
Log in to the web UI and choose System > Maintenance.
This function upgrades the firmware of the wireless bridge for more functions and higher stability.
To prevent damaging the wireless bridge, verify that the new firmware version is applicable to the
wireless bridge before upgrade and keep the power supply of the wireless bridge connected during
an upgrade.
24
DS-3WF01C-2N/O User Guide
Configuration procedure
Step 1 Choose System > Maintenance.
Step 2 Click Browser.
Step 3 Select an upgrade file and click Upload.
Step 4 Confirm the message on the pop-up window, and click OK.
----End
A progress bar is displayed on the page. Wait for it to elapse.
Then Log in to the web UI of the wireless bridge, and check the Firmware on the Status page, and
ensure that the version displayed here is the same as the firmware you upgrade.
After the firmware is upgraded, you are recommended to restore the factory settings of the
wireless bridge and configure it again, so as to ensure stability of the wireless bridge and proper
operation of new functions.
25
DS-3WF01C-2N/O User Guide
6.2 Time settings
Log in to the web UI and choose System > Time Settings.
In this module, you can set the system time of the wireless bridge. The wireless bridge supports to
manually set up the system time and to let the system time synchronize with the Internet.
6.2.1 Manual
Log in to the web UI and choose System > Time Settings.
You can manually set the system time of the wireless bridge. If you choose this option, you need
to set the system time each time after the wireless bridge reboots.
Configuration procedure
Step 1 Choose System > Time Settings.
Step 2 Click the Date & Time input box.
Step 3 Set the date and time for the wireless bridge, or click Synchronize with PC Time button to
synchronize the time to that of the management computer.
Step 4 Click OK.
----End
6.2.2 Synchronize with the internet
Log in to the web UI and choose System > Time Settings.
The wireless bridge automatically synchronizes its system time with a time server of the internet.
This enables the wireless bridge to automatically correct its system time after being connected to
the internet.
For details about how to connect the wireless bridge to the internet, refer to Network.
Configuration procedure
Step 1 Choose System > Time Settings, and move to the Synchronize with the Internet part.
26
DS-3WF01C-2N/O User Guide
Step 2 Check the Enable box.
Step 3 Enter the IP address of the NTP server, which is 185.134.197.4 in this example.
Step 4 Enter the NTP port. The default is 123.
Step 5 Set a synchronization Interval at which the wireless bridge synchronize its time with the
internet.
Step 6 Click Save.
----End
6.3 Basic Service
Log in to the web UI and choose System > Basic Service.
In this module, you can set the SSH function, and export system logs.
6.3.1 SSH server
Log in to the web UI, choose System > Basic Service.
Secure Shell (SSH) uses encryption and authentication mechanisms to achieve remote access and
file transmission services.
This wireless bridge supports SSH server, and allows SSH client to connect to it.
SSH server is disabled by default.
Assume that you want to log in to the wireless bridge (192.168.1.35) and configure it form the
computer installed with the SSH client software.
27
DS-3WF01C-2N/O User Guide
Configuration procedure
Step 1 Choose System > Basic Service, and move to the SSH Server part.
Step 2 Check the Enable box.
Step 3 Run the SSH client software on the management computer. PuTTY is used for illustration.
(1) Run the Putty.
(2) Set Connection type to SSH.
(3) Set Host Name (or IP address) to 192.168.1.35.
(4) Click Open.
Step 4 Enter the user name (hikvision) and login password of the wireless bridge according to the
instructions to log in to the configuration page.
28
DS-3WF01C-2N/O User Guide
----End
6.3.2 Export
Log in to the web UI, choose System > Basic Service, and move to Export part.
The logs of the wireless bridge record various events that occur and the operations that users
perform after the wireless bridge starts. In case of a network fault, you can refer to the logs during
troubleshooting.
To ensure that the logs are recorded correctly, verify the system time of the wireless bridge. You
can correct the system time of the wireless bridge by choosing System > Time Settings.
When the wireless bridge reboots, the previous logs are lost.
The wireless bridge reboots when it is powered on again, the firmware is upgraded, a wireless
bridge configuration is imported or the partial reset or reset is performed.
29
DS-3WF01C-2N/O User Guide
6.4 Account
Log in to the web UI and choose System > Account.
On this module, you can change the login account information of the wireless bridge to prevent
unauthorized login.
Changing the login password
Step 1 Choose System > Account.
Step 2 Click Change.
Step 3 Enter the current login password in the Old Password input box.
Step 4 Customize a new login password in the New Password input box.
Step 5 Enter the new password you set again in the Confirm New Password input box.
Step 6 Click Save.
----End
30
DS-3WF01C-2N/O User Guide
Parameters
Default
Login
Login IP address
192.168.1.36
User name
admin
Password
/
Network
IP Address
192.168.1.36
Subnet Mask
255.255.255.0
Gateway
0.0.0.0
DNS1
0.0.0.0
DNS2
0.0.0.0
Wireless
Operating Mode
CPE
SSID
HIKVISION_XXXXXXXXXXX, XXXXXXXXXXX is the serial number
of the wireless bridge.
Network Mode
11b/g/n
Channel
auto
Security Mode
WPA2-PSK
Security Key
123456789abc
System
Device Name
Wireless Bridge
Time Settings
Manual
SSH
Disable
Appendix
A Default parameters
By default, the parameters are shown in the following table:
31
DS-3WF01C-2N/O User Guide
Acronym or Abbreviation
Full Spelling
DNS
Domain Name System
IPv4
Internet Protocol version 4
MAC
Media Access Control
NTP
Network Time Protocol
PoE
Power Over Ethernet
PSK
pre-shared key
SSH
Secure Shell
SSID
Service Set Identifier
B Acronyms and Abbreviations
32
DS-3WF01C-2N/O User Guide
33
Loading...