HIKVISION DS-2XE6222F-IS, DS-2XE6252F-IS, DS-2XE6212F-IS, DS-2XE6242F-IS, DS-2XE6232F-IS Quick Start Manual

...

Download

Explosion-Proof Network Bullet Camera

Quick Start Guide

UD04283B

0504051070109

Network Bullet Camera·Quick Start Guide

Quick Start Guide

Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).

This user manual (hereinafter referred to be “the Manual”) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of

Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties, guarantees or representations, express or implied, regarding to the Manual.

About this Manual

This manual is applicable to XE62 Series Explosion-Proof Network

Bullet Camera.

The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The

information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version in the company website

(http://overseas.hikvision.com/en/).

Please use this user manual under the guidance of professionals.

Trademarks Acknowledgement

and other Hikvision’s trademarks and logos are the

properties of Hikvision in various jurisdictions. Other trademarks and

Network Bullet Camera·Quick Start Guide

logos mentioned below are the properties of their respective owners.

Legal Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND

FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY,

SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE

LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF

DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF

PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER

ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.

SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL

RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE

Network Bullet Camera·Quick Start Guide

APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.

IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.

Regulatory Information

FCC Information

Please take attention that changes or modification not expressly

approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment

in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

Network Bullet Camera·Quick Start Guide

EU Conformity Statement

This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized

European standards listed under the EMC Directive 2014/30/EU, the LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU, the ATEX

Directive 2014/34/EU.

2012/19/EU (WEEE directive): Products marked

with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier

upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see:

www.recyclethis.info

2006/66/EC (battery directive): This product

contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery

information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your

supplier or to a designated collection point. For more information see:www.recyclethis.info

Intended use of the camera

ATEX: II 2 G D Ex db IIC T6 Gb/Ex tb IIIC T80℃ Db IP68

IECEx: Ex db IIC T6 Gb/Ex tb IIIC T80℃ Db IP68

Hazardous Area Classification: Zone 1, Zone 2, Zone 21, Zone 22.

Network Bullet Camera·Quick Start Guide

IP Degree: IP68 (2m, 2h)

Ex Standards:

IEC 60079-0: 2011

EN 60079-0: 2012

IEC 60079-1: 2014

EN 60079-1: 2014

IEC 60079-31: 2013

EN 60079-31: 2014

Nameplate:

Special Conditions for Safe Use:

1. Ambient Temperature: -30°C to +60°C.

2. DO NOT OPEN WHEN ENERGIZED.

3. POTENTIAL ELECTROSTATIC CHARGING HAZARD – SEE

INSTRUCTIONS.

4. When assembly, operation and maintenance, the operator must

follow the requirements of the IEC 60079-14: latest version Explosive atmosphere- Part 14: Electrical installation design, selection and erection, beside of the manufacturer’s operation

instruction or its National equivalent.

Network Bullet Camera·Quick Start Guide

5. Repair and overhaul shall comply with IEC 60079-19: latest version

or its National equivalent.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

Warning:

This is a class A product. In a domestic environment this product may

cause radio interference in which case the user may be required to take adequate measures.

Safety Instruction

These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss.

The precaution measure is divided into “Warnings” and “Cautions”

Warnings: Serious injury or death may occur if any of the warnings

are neglected.

Cautions: Injury or equipment damage may occur if any of the

cautions are neglected.

Warnings Follow these safeguards to prevent serious injury or death.

Cautions Follow these precautions to prevent potential injury or material damage.

Network Bullet Camera·Quick Start Guide

Warnings

● Grounding:

The both internal and external earthing shall be connected

reliably.

Ground wire cross-sectional area of not less than the phase connector cross-sectional area level, at least 4 mm2.

● All the electrical operation should be strictly compliance with

the electrical safety regulations, fire prevention regulations and

other related regulations of the nation and region.

● Make sure that the power has been disconnected before you

wire, install or disassemble the camera. Never wire, install or

disassemble the camera in explosive environment.

● Do not connect several devices to one power adapter as

adapter overload may cause over-heating or a fire hazard.

● To avoid fire danger caused by electrostatic charge, never touch

or wipe the camera in explosive environment. Perform the wiping and replacing accessories only under non-explosive

environment with the provided glove.

● When the camera is installed on wall or ceiling, the device shall

be firmly fixed.

● If smoke, odors or noise rise from the camera, turn off the

power at once and unplug the power cable, and then contact

the service center.

Network Bullet Camera·Quick Start Guide

● If the camera does not work properly, contact your dealer or

the nearest service center. Never attempt to disassemble the speed dome yourself. (We shall not assume any responsibility

for problems caused by unauthorized repair or maintenance.)

Cautions

● Make sure the power supply voltage is correct before using the

camera.

● Do not drop the camera or subject it to physical shock.

● To ensure explosion-proof performance, do not damage

explosion-proof surface.

● Do not touch sensor modules with fingers. If cleaning is

necessary, use clean cloth with a bit of ethanol and wipe it

gently. If the camera will not be used for an extended period, please replace the lens cap to protect the sensor from dirt.

● Do not aim the camera at the sun or extra bright places.

Blooming or smearing may occur otherwise (which is not a

malfunction), and affect the endurance of sensor at the same time.

● The sensor may be burned out by a laser beam, so when any

laser equipment is in using, make sure that the surface of

sensor will not be exposed to the laser beam.

● Do not place the camera in extremely hot, cold (the operating

temperature shall be-30°C to +60°C), dusty or damp locations, and do not expose it to high electromagnetic radiation.

Network Bullet Camera·Quick Start Guide

● To avoid heat accumulation, good ventilation is required for

operating environment.

● To prevent accumulation of electrostatic charge, only damp

cloth can be used during the cleaning.

● Keep the camera away from liquid while in use.

● While in delivery, the camera shall be packed in its original

packing, or packing of the same texture.

● Regular part replacement: a few parts (e.g. electrolytic

capacitor) of the equipment shall be replaced regularly according to their average enduring time. The average time

varies because of differences between operating environment and using history, so regular checking is recommended for all the users. Please contact with your dealer for more details.

● Improper use or replacement of the battery may result in

hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer.

● If the product does not work properly, please contact your

dealer or the nearest service center. Never attempt to disassemble the camera yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or

maintenance.)

Network Bullet Camera·Quick Start Guide

Table of Contents

1 Introduction .................................................................................. 11

Overview ....................................................................... 11 1.1

Model Description......................................................... 11 1.2

2 Appearance Description ............................................................... 13

Overview ....................................................................... 13 2.1

Cable Description .......................................................... 14 2.2

3 Installation .................................................................................... 16

4 Setting the Network Camera over the LAN .................................. 20

Wiring ........................................................................... 20 4.1

Activating the Camera ................................................... 21 4.2

Activation via Web Browser ................................ 21 4.2.1

Activation via SADP Software ............................. 22 4.2.2

Modifying the IP Address .............................................. 24 4.3

5 Accessing via Web Browser .......................................................... 27

6 Operating via Hik-Connect App .................................................... 29

6.1 Enable Hik-Connect Service on Camera ......................... 29

Enable Hik-Connect Service via SADP Software .. 29 6.1.1

Enable Hik-Connect Service via Web Browser .... 30 6.1.2

6.2 Hik-Connect Setup ........................................................ 32

6.3 Adding Camera to Hik-Connect ..................................... 32

6.4 Initializing the Memory Card ......................................... 34

Network Bullet Camera·Quick Start Guide

1 Introduction

Overview 1.1

Explosion-proof network camera is a surveillance product capable of video/audio collecting, smart encoding and network transmitting. It

adopts an embedded system and a high-performed hardware process platform to achieve good stability and reliability.

You can visit and configure your camera via web browser and client software.

Explosion-proof network camera adopts a stainless steel enclosure,

receiving an IP68 rating for ingress protection.

Application Scenarios: oil industry, mine fields, chemical industry, port, grain processing industry, etc..

Model Description 1.2

This manual is applicable to the following models:

Applicable Model List Table 1-1

Model List

DS-2XE6212F-IS

DS-2XE6222F-IS

DS-2XE6232F-IS

DS-2XE6242F-IS

DS-2XE6252F-IS

DS-2XE6262F-IS

DS-2XE6282F-IS

Network Bullet Camera·Quick Start Guide

Explanation of model naming:

Supports on-board storage

DS-2

X E 6 2 1 2 F - I S

Hikvision front-end product

For specialized application

Application type: E: Stainless Steel Explosion Proof

Professional

Shape: 2: Bullet camera

Max. Resolution (MP): 1: 1.3 MP 5: 5.0 MP 2: 2.0 MP 6: 6.0 MP 3: 3.0 MP 8: 8.0 MP 4: 4.0 MP

Stands for hardware performance, including platform, sensor, etc.. Larger number means better performance

Extended function: I: IR S: Audio I/O, Alarm I/O, RS-485

Model Explanation Figure 1-1

Network Bullet Camera·Quick Start Guide

2 Appearance Description

Overview 2.1

Explosion-Proof Network Bullet Camera Overview (1) Figure 2-1

Explosion-Proof Network Bullet Camera Overview (2) Figure 2-2

Network Bullet Camera·Quick Start Guide

Cable Description 2.2

Power Supply

Network

Alarm In/Out

Overview of Cables Figure 2-3

Description of Cables Table 2-1

Cables

Description

Power Supply Voltage: 100 VAC to 240 VAC

YELLOW/GREEN: for grounding

Alarm In/Out

YELLOW/BLUE: ALARM_IN1

WHITE/RED: ALARM_OUT1

YELLOW/ORANGE: ALARM_IN2

WHITE/PURPLE: ALARM_OUT2

YELLOW/BLACK: ALARM_GND

Network Bullet Camera·Quick Start Guide

Cables

Description

Network

For network communication

Note:

ALARM_IN1 and ALARM_OUT1 (ALARM_IN2 and ALARM_OUT2) should be used in pairs for alarm input and output.

Network Bullet Camera·Quick Start Guide

3 Installation

Before you start:

● Make sure the device in the package is in good condition and all

the assembly parts are included.

● The standard power supply is 100 VAC to 240 VAC, please make

sure your power supply matches with your camera.

● Make sure all the related equipment is power-off during the

installation.

● Check the specification of the products for the installation

environment.

● Make sure that the wall is strong enough to withstand four

times the weight of the camera and the bracket.

For the camera that supports IR, you are required to pay attention to the following precautions to prevent IR reflection:

● Make sure that there is no reflective surface too close to the

camera lens. The IR light from the camera may reflect back into

the lens causing reflection.

Wall Mounting

Before you start:

There is no wall mounting bracket included in the package. You have to prepare a wall mounting bracket if you choose this mounting type. The shown bracket below is only for demonstration.

Steps:

1. Fix the wall mounting bracket to the desired place on wall with

four expansion screws.

Network Bullet Camera·Quick Start Guide

Expansion Screws

Figure 3-1 Install the Wall Mounting Bracket

2. Unscrew and remove the pedestal from the bracket.

Pedestal

Screws

Figure 3-2 Remove the Pedestal

3. Align the screw holes on the camera mounting base with those on

the pedestal, and fix the camera to the pedestal with the supplied screws.

Network Bullet Camera·Quick Start Guide

Pedestal

Mounting

Base

Screws

Safety

Rope

Figure 3-3 Fix the Camera to the Pedestal

4. Loosen the fixing screw, and adjust the panning position. Tighten

the fixing screw after adjustment.

Fixing Screw

Pan:

-45° to 45°

Figure 3-4 Adjust Panning Position

5. Use safety rope to hook the camera and the bracket. Adjust the

tilting position when screwing the camera to the wall mounting bracket.

Network Bullet Camera·Quick Start Guide

Tilt: -45° to 45°

Figure 3-5 Secure the Camera to Wall Mounting Bracket

6. Secure the screws to finish installation.

Network Bullet Camera·Quick Start Guide

4 Setting the Network Camera over the

LAN

Note:

You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your

own protection.

If the product does not work properly, contact your dealer or the nearest service center for help.

Wiring 4.1

Connect the camera to network according to the following figures.

Network Cable

Network Camera

Computer

Connecting Directly Figure 4-1

Network Cable

Network Camera Computer

Connecting via a Switch or a Router Figure 4-2

Network Bullet Camera·Quick Start Guide

Activating the Camera 4.2

You are required to activate the camera first by setting a strong password for it before you can use the camera.

Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We will take activation via SADP

software and Activation via Web Browser as examples to introduce the camera activation.

Note:

Refer to the User Manual of Network Camera for Activation via Client Software.

Activation via Web Browser 4.2.1

Steps:

1. Power on the camera. Connect the camera to your computer or

the switch/router which your computer connects to.

2. Input the IP address into the address bar of the web browser, and

press Enter to enter the activation interface.

Notes:

 The default IP address of the camera is 192.168.1.64.  The computer and the camera should belong to the same

subnet.

 For the camera enables the DHCP by default, you need to use

the SADP software to search the IP address.

Network Bullet Camera·Quick Start Guide

Activation Interface(Web) Figure 4-3

3. Create a password and input the password into the password

field.

STRONG PASSWORD RECOMMENDED– We highly

recommend you create a strong password of your own

choosing (using a minimum of 8 characters, including

upper case letters, lower case letters, numbers, and

special characters) in order to increase the security of

your product. And we recommend you reset your

password regularly, especially in the high security

system, resetting the password monthly or weekly can

better protect your product.

4. Confirm the password.

5. Click OK to save the password and enter the live view interface.

Activation via SADP Software 4.2.2

SADP software is used for detecting the online device, activating the camera, and resetting the password.

Network Bullet Camera·Quick Start Guide

Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts.

Follow the steps to activate the camera.

Steps:

1. Run the SADP software to search the online devices.

2. Check the device status from the device list, and select the

inactive device.

Select inactive device.

Input and confirm password.

SADP Interface Figure 4-4

Note:

The SADP software supports activating the camera in batch. Refer to the user manual of SADP software for details.

3. Create and input the new password in the password field, and

confirm the password.

Network Bullet Camera·Quick Start Guide

STRONG PASSWORD RECOMMENDED– We highly

recommend you create a strong password of your own

choosing (using a minimum of 8 characters, including

upper case letters, lower case letters, numbers, and

special characters) in order to increase the security of

your product. And we recommend you reset your

password regularly, especially in the high security

system, resetting the password monthly or weekly can

better protect your product.

Note:

You can enable the Hik-Connect service for the device during

activation. Refer to Chapter 6.1 for detailed information.

4. Click Activate to start activation.

You can check whether the activation is completed on the popup window. If activation failed, make sure that the password meets the requirement and try again.

Modifying the IP Address 4.3

Purpose:

To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC.

Use the SADP software or client software to search and change the

IP address of the device. We take modifying the IP Address via SADP software as an example to introduce the IP address modification.

For IP address modification via client software, refer to the user manual of client software.

Network Bullet Camera·Quick Start Guide

Steps:

1. Run the SADP software.

2. Select an active device.

3. Change the device IP address to the same subnet with your

computer by either modifying the IP address manually or checking the checkbox of Enable DHCP.

Modify the IP Address Figure 4-5

Network Bullet Camera·Quick Start Guide

Note:

You can enable the Hik-Connect service for the device during activation. Refer to Chapter 6.1 for detailed information.

4. Input the admin password and click Modify to activate your IP

address modification.

The batch IP address modification is supported by the SADP. Refer to

the user manual of SADP for details.

Network Bullet Camera·Quick Start Guide

5 Accessing via Web Browser

System Requirement:

Operating System: Microsoft Windows XP SP1 and above version

CPU: 2.0 GHz or higher

RAM: 1G or higher

Display: 1024×768 resolution or higher

Web Browser: Internet Explorer 8.0 and above version, Apple Safari

5.0.2 and above version, Mozilla Firefox 5.0 and above version and

Google Chrome 18 and above version

Steps:

1. Open the web browser.

2. In the browser address bar, input the IP address of the network

camera, and press the Enter key to enter the login interface.

Note:

 The default IP address is 192.168.1.64. You are recommended

to change the IP address to the same subnet with your

computer.

3. Input the user name and password.

The admin user should configure the device accounts and user/operator permissions properly. Delete the unnecessary accounts and user/operator permissions.

Note:

The device IP address gets locked if the admin user performs 7

failed password attempts (5 attempts for the user/operator).

Network Bullet Camera·Quick Start Guide

4. Click Login.

5. Install the plug-in before viewing the live video and managing the

camera. Follow the installation prompts to install the plug-in.

Note:

You may have to close the web browser to finish the installation of the plug-in.

Download Plug-in Figure 5-2

6. Reopen the web browser after the installation of the plug-in and

repeat steps 2 to 4 to login.

Note:

For detailed instructions of further configuration, please refer to the user manual of network camera.

Network Bullet Camera·Quick Start Guide

6 Operating via Hik-Connect App

Purpose:

Hik-Connect is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so on.

Note:

Hik-Connect service is not supported by certain camera models.

6.1 Enable Hik-Connect Service on Camera

Purpose:

Hik-Connect service should be enabled on your camera before using the service.

You can enable the service through SADP software or web browser.

Enable Hik-Connect Service via SADP Software 6.1.1

Steps:

1. Check the checkbox of Enable Hik-Connect on:

1). "Activate the Device" page during camera activation, refer to

Chapter 4.2.2.

2). Or "Modify Network Parameters" page during modifying IP

address, refer to Chapter 4.3.

2. Create a verification code or change the verification code.

Network Bullet Camera·Quick Start Guide

Verification Code Setting (SADP) Figure 6-1

Note:

The verification code is required when you add the camera to

Hik-Connect app.

3. Click and read "Terms of Service" and "Privacy Policy".

4. Confirm the settings.

Enable Hik-Connect Service via Web Browser 6.1.2

Before you start:

You need to activate the camera before enabling the service. Refer to

Chapter 4.2.

Network Bullet Camera·Quick Start Guide

Steps:

1. Access the camera via web browser. Refer to Chapter 5.

2. Enter platform access configuration interface: Configuration >

Network > Advanced Settings > Platform Access

Platform Access Configuration (Web) Figure 6-2

3. Select Platform Access Mode as Hik-Connect.

4. Check the checkbox of Enable.

5. Click and read "Terms of Service" and "Privacy Policy" in pop-up

window.

6. Create a verification code or change the verification code for the

camera.

Note:

The verification code is required when you add the camera to

Hik-Connect app.

7. Save the settings.

Network Bullet Camera·Quick Start Guide

6.2 Hik-Connect Setup

Steps:

1. Download and install the Hik-Connect app by searching

“Hik-Connect” in App Store or Google PlayTM.

2. Launch the app and register for a Hik-Connect user account.

3. Log in Hik-Connect app after registration.

6.3 Adding Camera to Hik-Connect

Before you start:

You need to enable the Hik-Connect service on camera before

adding it to your Hik-Connect account. Refer to Chapter 6.1.

Steps:

1. Use a network cable to connect the camera with a router if the

camera does not support Wi-Fi.

Figure 6-3 Connect a Router

Note:

After the camera connects to the network, please wait one minute before any operation on the camera using Hik-Connect app.

2. In the Hik-Connect app, tap “+” on the upper-right corner and

then scan the QR code of the camera to add the camera.

Network Bullet Camera·Quick Start Guide

You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package.

Figure 6-4 Scan QR Code

Note:

If the QR code is missing or too blur to be recognized, you can also add the camera by tapping the icon and inputting the camera's serial number.

3. Input the verification code of your camera.

Note:

● The required verification code is the code you create or

change when you enabling Hik-Connect service on camera.

● If you forget the verification code, you can check the current

verification code on Platform Access configuration page via web browser.

4. Follow the prompts to set the network connection and add the

camera to your Hik-Connect account.

Note:

For detailed information, refer to the user manual of the Hik-Connect app.

Network Bullet Camera·Quick Start Guide

6.4 Initializing the Memory Card

Check the memory card status by tapping on the Storage Status in the Device Settings interface.

If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start

recording any event triggered video in the camera such as motion detection.

HIKVISION DS-2XE6222F-IS, DS-2XE6252F-IS, DS-2XE6212F-IS, DS-2XE6242F-IS, DS-2XE6232F-IS Quick Start Manual

Specifications and Main Features

Frequently Asked Questions

User Manual