HIKVISION DS-2CE16D7T-AIT3Z, DS-2CE16D7T-IT3Z, DS-2CE56D7T-IT3Z, DS-2CE16F7T-AIT3Z, DS-2CE16F7T-IT3Z User Manual

Type

Model

Type I Camera

DS-2CE16D(F)7T-AIT3Z

DS-2CE16D(F)7T-IT3Z

Type II Camera

DS-2CE56D(F)7T-IT3Z

TURBO HD
D(F)7T Series

Bullet & Turret Camera

User Manual

UD00380B

User Manual

Thank you for purchasing our product. If there are any
questions, or requests, please do not hesitate to
contact the dealer.

This manual applies to the models below:

This manual may contain several technical incorrect
places or printing errors, and the content is subject to
change without notice. The updates will be added to
the new version of this manual. We will readily improve
or update the products or procedures described in the
manual.

0100001060119

Privacy Notice

Surveillance laws vary by jurisdiction. Check all relevant
laws in your jurisdiction before using all this product for
surveillance purpose to ensure that your use of this
product conforms.

Regulatory Information

FCC Information

FCC compliance: This equipment has been tested and

found to comply with the limits for a digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference when the equipment is operated
in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in
which case the user will be required to correct the
interference at his own expense.

FCC Conditions

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received,
including interference that may cause undesired
operation

EU Conformity Statement

This product and - if applicable - the
supplied accessories too are marked with
"CE" and comply therefore with the

standards listed under the Low Voltage Directive
2006/95/EC, the EMC Directive 2004/108/EC.

upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more
information see: www.recyclethis.info.

this symbol, which may include lettering to indicate
cadmium (Cd), lead (Pb), or mercury (Hg). For proper
recycling, return the battery to your supplier or to a
designated collection point. For more information see:
www.recyclethis.info.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (A)/NMB-3(A)
standards requirements.

applicable harmonized European

2002/96/EC (WEEE directive): Products
marked with this symbol cannot be
disposed of as unsorted municipal waste in
the European Union. For proper recycling,
return this product to your local supplier

2006/66/EC (battery directive): This
product contains a battery that cannot be
disposed of as unsorted municipal waste in
the European Union. See the product
documentation for specific battery
information. The battery is marked with

Photoconductive
Resistance

Model I Cables

Video Cable

24VAC/12VDC
Power Cord

Video Cable

DC 12V
Power Cord

Model II Cables

Main Body

Lens

Bracket

Cables

Auxiliary Video
Output

Menu Button

Camera

Lock Screw

Enclosure

Video Cable

DC 12V
Power Cord

Base Plate

1 Introduction

1.1 Product Features

This series of camera adopts high performance sensor
and advanced circuit board design technology. It
features high resolution, low distortion, and low noise,
etc. It is suitable for surveillance system and image
process system.

The main features are as follows:

 High performance CMOS sensor and high resolution

bring high-quality image;

 Low illumination, 0.01 Lux @ (F1.2, AGC ON), 0 Lux

with IR;

 IR cut filter with auto switch;
 OSD menu, parameters are configurable;
 Auto white balance and internal synchronization;
 SMART IR mode;
 True WDR;
 Advanced 3-axis design meets different installation

requirements

1.2 Overview

 The cables of device vary according to different models. The

cables of each type are shown in the figures below, please
refer to the actual sample.

 You can debug the camera by connecting an auxiliary HD

TVI cable to the auxiliary video output.

1.2.1 Overview of Type I Camera

Figure 1-1 Overview of Type I Camera

1.2.2 Overview of Type II Camera

Figure 1-2 Overview of Type II Camera