Hikvision DS-2CE16C2T-IR-2-8MM, DS-2CE16C2T-IR-3-6MM, DS-2CE16C2T-IR-6MM, DS-2CE16D5T-IT3 3.6MM, DS-2CE16D5T-IT3-12MM User Manual
...
TURBO HD
Bullet Camera
User Manual
UD.6L0201D1813A01
Thank you for purchasing our product. If there
are a ny qu est ions, or requests, p lease do not
hesitate to c ontact t he dealer.
This manual applies to
Type
DS-2CE16C2T-IRP
I
720P
1080P
This manua l may contain s everal technical
incorrect places or printing errors, and the
content is subject to change without notice.
The updates wil l be ad ded to the new version of
this manual. We will readily improve or update
the products or procedures described in the
manual.
Please refer to the product specification for
camera parameters and functions.
0100001050303
DS-2CE16C2T-IR
DS-2CE16C2T-IT1
II
DS-2CE16C2T-IT3
III
DS-2CE16C2T-IT5
I
DS-2CE16D5T-IR
DS-2CE16D5T-IT1
II
DS-2CE16D5T-IT3
III
DS-2CE16D5T-IT5
www.hikvision.com
Model
Regulatory Information
FCC Information
FCC compliance: This equipment has been
tested and found to comply with the limits for a
digital devic e, pu rsu ant t o part 15 of the FCC
Rules. The se limits are des ign ed to prov ide
reasonable protection against harmful
interference when the equipment is operated in
a commercial environment. This equipment
gen erates , use s, and can radiate radi o
frequency energy and, if not installed and used
in accordance with the instruction manual, may
cau se harmful i nterference to ra dio
communications. Operation of this equipment in
a residential area is likely to cause harmful
interference in which case the user will be
req uired to c orrect the interfer enc e at his own
expense.
FCC Conditions
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
1. This devi ce may not c aus e harmful
interference.
2. This device must accept any interference
received, including interference that may
cause undesired operation.
EU Conformity Statement
This product an d - if applicable - t he
supplied accessories too are marked
with "CE" an d com ply therefo re wi th
the applicable harmonized European
standa rds l ist ed un der the Low Vol tage Direct ive
2006/95/EC, the EMC Directive 2004/108/EC,
the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive):
Products marked with this symbol
cannot be disposed of as unsorted
municipal waste in the European
Union. For proper recycling, return
upon the purchase of equivalent new equipment,
or dispose of it at designated collection points.
For more information see:
See the product documentation for specific
bat ter y inform ati on. The battery is mar ked with
this symbol, wh ich m ay in clude lettering to
indicate ca dmium (Cd) , lead (Pb), o r mercury (Hg).
For p rop er re cyc ling, return th e batter y to your
supplier or to a designated collection point. For
more information see: www.recyclethis.info.
this product to your local supplier
www.recyclethis.info.
2006/66/EC (battery directive):
This product contains a battery that
cannot be disposed of as unsorted
municipal waste in the European
Union.
1 Introduction
1.1 Product Features
This serie s of ca mera adopts new generation
sensor with high sensitivity and advanced circuit
design technology It features high resolution,.
low image distortion an d low noise, e tc , which.
makes it suitable for surveillance system and
image processing system.
l High performance CMOS sensor and high
resolution bring high-quality image;
l Low illumination;
l OSD menu, pa rameters are configurable;
l Support auto white balance, auto gain control,
electronic shutter control;
l
SMART IR mode;
l
Unit transmission control;
l Advanced 3-axis design meets different
installation requirements.
1.2 Overview
1.2.1 O verview of Type I Camera
Switch Cable
Mounting Base
CVBS Cable
Sun Shield
Lens
IR LED
1.2.2 O verview of Type Camera
Adjustable Screw
Sun Shield
IR LED
Switch Cable
Mounting Base
1.2.3 Overview of Type CameraIII
Sun Shield
Lens
IR LED
Adjustable Screw
Power Ca ble
HD Video Cable
II
Power Ca ble
CVBS Cable
HD Video Cable
Switch Cable
CVBS Cable
Power Ca ble
HD Video Cable
l All the diag rams onl y apply to cameras with
a 1080p resolution. The cameras with a 720p
res olution of t hese three type s do not hav e
CVBS cables and switch cables.
l
The switch cables are designed for toggling
status o f the WDR func tions fo r 1080p cameras.
The WDR func tion is disa bled by defau lt, and
you c an short the w hit e and black line- ends of
the switch cable to enabl e the functi on.
2 Installation
Before you start:
l Pleas e make sure that the d evice in the package
is in good condition and all the assembly parts
are i ncluded.
l Make sure that all the related equi pment is
power-off during the installation.
l Check t he specifi cat ion o f the products for the
installation environment.
l Check whether the power supply is matched
with your power outp ut to avoi d damage.
l Pleas e make sure the wall i s strong e nough to
withstand three times the weight of the camera
and the mounting.
l If the wall is t he cement wall, you ne ed to i nsert
exp ansion screws before you i nst all t he camera.
If the wall is the wooden wall, you can use
self-tappin g screw to s ecure the camera.
l If the product does not function properly,
please contact your dealer or the nearest
servi ce ce nte r. Do not d isassemb le the camera
for repair or maintenance by yourself.
2.1 Ceiling Mounting for Type I
Camera
Steps:
1.Drill the s crew hol es and the cab le ho le in the
ceiling according to the supplied drill template.
2.Hammer the supplied plastic expansion bolt into
the screw holes .
All Screw Holes: for
mounting base
Figure 2-1 Drill Template
3.Route the cables to the cable hole and connect
the corresponding power cable and video cable.
4.Fix the camera to the ceiling with the supplied
screws.
Figure 2-2 Fix the Camera to the Ceiling
5.Adjust the surveillance angle.
1).Loosen No.3 adjusting screw to adjust the
panning position 0 ~ 360 .(° °)
.2).Tighten No.3 adjusting screw
3).Loosen the No.2 adjusting screw to adjust the
tilting position 0 ~ 90(° °).
4).Tighten No.2 adjusting screw.
5).Loosen No.1 adjusting screw to adjust the
azimuth an gle of the ima ge 0 ~ 360(° °).
.6).Tighten No.1 adjusting screw
Figure 2-3 3-axis Adjustment
2.2 Wall Mounting for Type /IIIII
Camera
Steps:
1.Drill the s crew hol es and the cab le ho le in the
ceiling according to the supplied drill template.
2.Hammer the supplied plastic expansion bolt into
the screw holes .
2
Ceiling Mounting
1
2
No.1 Screw Hole
for Bracket
1
Figure 2-4 Drill Template
2
1
2
No.2 Screw Hole
for Mounting
Base
1
3.Route the cables to the cable hole and connect
the corresponding power cable and video cable.
4.Fix the camera to the ceiling with the supplied
screws.
Adjusting Screw
Figure 2-5 Fix th e Camera t o the Wall
5. Adjust the surveillance angle.
1). Loosen No.3 adjusting screw to adjust the pan
position (0 ~ 360 ).°°
2).Tighten No.3 adjusting screw.
3). Loosen No.2 adjusting screw to adjust the
tilting position(0 ~ 90 ).°°
4).Tighten No.2 adjusting screw.
5). Loosen No.1 adjusting screw to adjust the
rotation position 0 ~ 360 .(° °)
6).Tighten No.1 adjusting screw.
360°
3
90°
2
360°
1
Figure 2-6 3-axis Adjustment
3 Menu Operation
Menu
VIDEO.
OUT
BACKLIGHT
EXPOSURE
SCENE
INDOOR
OUTDOOR
INDOOR1
LOWLIGHT
LENS
MANUAL
SHUTTER
AGC
SENS-UP
BRIGHTNESS
D-WDR
DEFOG
HSBLC
WB
BLC
ATW
AWC-SET
INDOOR
OUTDOOR
MANUAL
Figure 3-1 Main Menu
l A coaxial camera controller (purchase separately)
is required to select the menu and adjust the
camera parameters.
l
Camera s with a 720p resol ution of the se three
types do not support menu operation.
SETUP
DAY&NIGHT
COLOR
B/W
EXT
LAUGUAGE
2D NR
3D NR
ADJUST
SPECIAL
NR
CAM
TITLE
D-EFFECT
MOTION
PRIVACY
DEFECT
VERSION
SHARPNESS
MONITOR
LSC
RESET
EXIT
3.1 VIDEO.OUT
PAL or NTSC is selectable .
3.2 LANGUAGE
English, J apanese, C HN1 , CHN2, Korean, Germ an,
French, Italian, Spanish, Polish, etc., are selectable.
3.3SETUP
3.3.1 SCENE
You can select indoor, outdoor, indoor 1 and low
-light as the wor kin g env iro nments.
3.3.2 LENS
The camera is equipp ed with a fixed lens.
3.3.3 EXPOSURE
SHUTTER: AUTO,1/25, 1/5 0, FLK, 1/20 0, 1/400,
1/1k, 1/2k , 1/5k, 1/10 k, 1/ 50k, x2, x4, x 6, x8, x10,
and x15 are selectable.
: You can set the AG C value from 0 to 1 5.AGC
: You can set the SE NS-UP to OFF or AUTO.SENS-UP
: You can set the br ightness valueBRIGHTNESS
fro m 1 to 10 0.
: You can set the D- WDR to ON to improveD-WDR
the image quali ty or OFF to disabl e the functi on.
: You can set the defog func tion as ON toDEFOG
enable the function. Position, size, and the defog
gradation are configurable.
EXPOSURE
1. SHUTTER AUTO
2. AGC OFF
3. SENS-UP ---
4. BRIGHTNESS ---|------ 40
5. DEFOG OFF
6. BACKLIGHT OFF
7. RETURN RET
Figure 3-2 Exposure
HSBLC
1. SELECT AREA 1
2. DISPLAY ON 8
3. LEVEL ---|------ 40
4. MODE ALL DAY
5. BLACK MASK ON
6. DEFAULT 8
7. RETURN RET
Figure 3-3 HSBLC
3.3.4 Backlight
Backlight Compensation (BLC):
Set the ga in of BLC as High, Mi ddle, or Low.-GAIN:
Press the up/down/left/right button to-AREA:
define the BLC position and size. Select RET or
AGA IN to go back the BLC menu o r re- define the
BLC a rea .
Restore the BLC settings t o the d efa ult .-Default:
HSBLC: Select an HSBLC area. Set the DISPLAY
status as ON. Press the up/down/left/right button
to de fine the area pos iti on and size. Set the HSB LC
LEVEL from 0 to 100. Select ALL DAY or Night for the
HSBLC mode. Set t he BLACK MASK status as ON or
OFF.
3.3.5 White Balance (WB)
INDOOR, OUTDOOR, MANUAL, ATW (Auto-tracking
White Balance), AWC→SET are selectable.
3.3.6 Day & Night
Color, B/W, and EXT are selectable for DAY and
NIGHT switches.
3.3.7 NR
: You can set 2D NR status as ON o r OFF.2D NR
: Set the Smart NR status as ON and adjust3D NR
the 3D smart N R sensitiv ity ranges from 0 to 1 00.
Set the 3D NR LE VEL ranges from 0 to 1 00. S et the
START. AGC l eve l as the threshol d to en able AGC,
and set the EN D. AGC level as the th res hold to
disable AGC.
2D&3D NR
1. 2DNR OFF
2. 3DNR ON
3. RETURN RET
Figure 3-5 NR
8
3D NR
1. SMART NR ON
2. LEVEL ------|--8 0
3. START. AGC -|--------10
4. END. AGC -|--------10
5. RETURN RET
8
Figure 3-6 3D NR
3.3.8 SPECIAL
Edi t the camera title on th is section.Camera Title:
D-effect:
Set the freeze fun ction as ON or O FF.-FREEZE:
OFF, MIRROR, V- FLI P, and ROTATE are-MIRROR:
selectable for mirror.
Define the zoom area by configuring-D-ZOOM:
the positi on from PAN & TILT.
The D-Zoom area, sensitivity-SMART D-ZOOM:
and time are configurable.
Set the NEG IMAGE as ON or O FF.-NEG.IMAGE:
SPECIAL
1. CAM TITLE ON
2. D-DFFECT 8
3. MOTION OFF
4. PRIVACY O FF
5. LANGUAGE ENG
6. DEFECT 8
7. VERSION 130722
8. RETURN RET
8
8
Figure 3-7 Special
Figure 3-8 Moti on Detection
MOTION
1. SELECT AREA 1
2. DISPLAY ON8
3. SENSITIVITY ----|---- 30
4. MOTION VIEW ON
5. DEFAULT 8
6. RETURN RET
Motion: Select a MOTION area. Set the DISPLAY
status as ON or OFF. Press the up/down/left/right
button t o def ine the posi tion and size of the area.
Set the SENSITI VITY from 0 to 60. Set the M OTION
VIEW sta tus as ON or OFF.
Privacy: Select a PRIVACY area. Set the DISPLAY
status a s INV, MOSAIC, COLOR or OFF. Press the
up/down/left/right button to define the position
and size o f the area.
Defect: LIVE DPC , STATIC DPC an d Black DPC are
adjustable in this section.
: You can che ck th e software version of theVersion
device.
Figure 3-9 Privacy Mask
PRIVACY
1. SELECT AREA1
2. DISPLAY MOSAIC
3. COLOR 10
4. TRANS. 1
5. DEFAULT
6. RETURN RET
8
ADJUST
8
1. SHARPNESS
2. MONITOR LCD8
3. LSC OFF
4. VIDEO. OUT PA L
5. RETURN RET
--------|15
Figure 3-10 Adjust
3.3.9 ADJUST
: Adjust the sharpness from 0 to 15.Sharpness
: Monitor CRT, and Monitor LCD areMonitor
selectable.
: Set the LSC status as ON or OFF.LSC
3.3.10 RESET
Res et al l the settings to the default.
3.3.11 EXIT
Pre ss OK to exi t the menu.
Loading...