Hikvision DS-2CE15C2N-VFIR3 User Manual
Bullet Camera
User Manual
UD.6L 02 01 D1 10 4A 01
www.hi kv is io n. co m
Thank you for purchasing our pro duct. If there
are a ny questions, or requests , pl ea se d o no t
hesitate to cont ac t th e de al er.
This manual applies to
Type
DS- 2CE15 12P(N )-IR, D S-2CE 1582P (N)-I R
DS- 2CE15 A2P(N )-IR, DS-2C E15C2 P(N)- IR
Ⅰ
DS- 2CE15 82P(N )-IRP,DS-2 CE15A 2P(N) -IRP
DS- 2CE16 82P(N )-IT1 ,
DS- 2CE16 C2P(N )-IT1 ,
Ⅱ
DS- 2CE16 A2P(N )-IT3 ,DS-2 CE16C 2P(N) -IT3
DS- 2CE16 82P(N )-IT5 ,
Ⅲ
DS- 2CE16 C2P(N )-IT5
DS- 2CE15 82P(N )-VFI R3,DS -2CE1 5A2P( N)-VF IR3
Ⅳ
DS- 2CE15 C2P(N )-VFI R3
This manual may c ontain seve ral technical
incor re ct p la ce s or p ri nting errors, a nd t he
con tent is subject to change without notice.
The updates w il l be a dd ed t o th e new version of
this manual. We will readily impro ve or update
the pro du ct s or p rocedures described in the
manual.
0200001030603
Model
DS- 2CE16 A2P(N )-IT1
DS- 2CE16 82P(N )-IT3
DS- 2CE16 A2P(N )-IT5
Regulatory Information
FCC Information
FCC com pl ia nc e: T hi s eq uipment ha s be en t ested
and fou nd to comply with the limits for a digita l
device, pursu ant to part 15 of the FCC Rules.
These limits are de si gn ed t o provide reasonable
pro tection against harmf ul i nterferen ce w he n th e
equipment is operated in a commerc ia l
env ironment. This equipment generates, uses,
and can radiate ra di o frequency energy and, if
not insta ll ed a nd u se d in a cc ordance with the
instr uc ti on m anual, may cause harmful
int er feren ce t o radio communicati on s. O pe ration
of this equipment in a re si de ntia l area is likel y to
cau se harmf ul i nterfer en ce i n wh ic h case the user
will be req ui red to correc t th e in terfere nc e at his
own exp en se .
FCC Conditions
This device com pl ie s wi th p art 15 of the FC C
Rules. Operation is sub je ct to the followi ng two
con ditions:
1. This device may no t cause harmful
int er feren ce .
2. This device must a cc ep t any interference
rec ei ved, i nc lu di ng i nterference that may
cau se undesired o pe ration.
EU Conformity Statement
This prod uc t an d - if a pp li ca bl e -
the supplied accessories too are
marked with "CE" and comply
there fore wi th t he a pplica bl e ha rm on ized
Europ ea n standards liste d un de r th e Lo w Vol tage
Direc ti ve 2 00 6/ 95 /EC, the EMC Directive 20 04 /
108/EC, t he RoHS Directive 2 01 1/ 65 /EU.
2012/19/EC (W EEE dire ct ive):
Pro du ct s ma rked with this sy mb ol
can not be disposed of as unsorted
municipal was te in the European
Union. Fo r proper recycling, ret ur n
upon the purc ha se o f eq uiva le nt new equipment,
or dispose of it at designate d collection points.
For m ore informati on s ee :w ww.recycleth is.info.
this prod uc t to your local supplier
2006/66/EC (b attery directive) :
This prod uc t co ntains a batter y
that ca nn ot b e di sp os ed o f as
unsorte d mu nicipal wa ste in the
Europ ea n Un io n.
See the pro du ct d oc um en tation fo r sp ec if ic
bat tery info rm at io n. T he b attery is marked with
this sy mb ol , wh ic h may include lette ri ng t o
indicate cadmium (Cd), lead (Pb), or mercury (Hg).
For p roper recyc li ng , re tu rn t he b attery to you r
supplier or to a designated collection point. For
more in formation see: www.rec yclethis.info .
1 Introduction
1.1 Product Features
This series of camera ado pts new generat io n
sensor with high sensitivity and advanced
circu it d es ig n te ch no lo gy. It features high
res ol ut io n, l ow i ma ge d istortion and low noise
features, etc. , wh ic h ma kes it suitab le for
surveillance system and image proc es si ng
system.
●High-perfor ma nc e se ns or a nd h ig h re so lu ti on
bring high-quality image
●IR LED enables the day/ ni gh t su rv ei ll an ce
●IR cut filter a ut o sw itch
●ATW brings high color rendition
●Ingre ss p rotection:IP66
1.2 Overview
Vi d eo C a bl e
Moun ti ng B as e
Su n S hi e ld
Le n s
IR L E D
Figure 1- 1 Ov er vi ew o f Typ e Ⅰ Ca me ra
Po we r C ab l e
Sun Shi el d
Lens
IR LED
Adjus table Screw
Power Cable
Video C ab le
Figure 1- 2 Ov er vi ew o f Typ e Ⅱ Ca me ra
Sun Shi el d
Lens
IR LED
Adjus table Screw
Power Cable
Video C ab le
Figure 1- 3 Ov er vi ew o f Typ e Ⅲ Ca me ra
Mou nting B as e
Len s
IR LE D
Vid eo Cabl e
Power Ca ble
Sun S hield
Figure 1- 4 Ov er vi ew o f Typ e Ⅳ Ca me ra
2 Installation
Before you start :
●Make sure that a ll the rel ated equipment is
power -o ff d ur in g th e in stallation.
●Check the specificati on o f th e prod uc ts for the
insta ll ation environ me nt .
●Check whether the power s up pl y is m atched
with yo ur A C ou tl et to avo id d am age.
●If the prod uc t do es n ot f unction prop er ly, please
con tact your dealer or the nearest s er vice
cente r. Do not disassemble th e camera for
rep ai r or m ai ntenance by yours el f.
●Please make sure that the ceiling or the wal l
is st rong enoug h to withstand 3 times the
wei gh t of t he camera.
2.1 Ceiling Mounting for Type I
Camera
Ste ps :
1.Drill the scre w ho le s an d th e ca bl e ho le i n th e
ceiling accordi ng to the supplied d ri ll template.
2.Hammer the supplied plastic ex pa ns io n bo lt i nto
the screw h ol es .
2.2 W Mounting for Type IIall / III
Camera
Ste ps :
1.Drill the scre w ho le s an d th e ca bl e ho le i n th e
ceiling accordi ng to the drill template.
2.Hammer the supplied plastic ex pa ns io n bo lt i nto
the screw h ol es .
2.3 Ceiling Mounting for Type IV
Camera
Ste ps :
1.Drill the scre ws holes a nd t he cable hole on the
ceiling accordi ng to the supplied d ri ll template.
2.Hammer the supplied plastic ex pa ns io n bo lt
int o th e sc rew holes.
1
90°
2
3
360°
Figure 2- 1 Dr il l Temp la te
3.Ro ute the cables to the cable hole and co nn ec t
the cor re sp on di ng p ower cable and video cable.
4.Fix the ca me ra to the ceiling with the supplied
screws.
Figure 2- 2 Fi x th e Ca me ra to the Ceiling
5.Adjust t he s urveillance angle.
1).Loosen No.3 adjusting screw to adjust the
panning position (0 ~ 360 .
° °)
2).Tight en N o. 3 ad ju stin g sc rew.
3).Loosen the No.2 adjusting screw to adjust the
tilting position (0° ~ 90°).
4).Tight en N o. 2 ad ju stin g sc rew.
5).Loosen No.1 adjusting screw to adjust the
azimuth angle of the image (0° ~ 360°).
6).Tight en N o. 1 ad ju stin g sc rew.
Figure 2- 3 3- ax is A dj ustment
2
1
2
No.1 Screw Hole
for Bracket
1
Ceiling Mounting
2
1
2
No.2 Screw Hole
for Mounting
Base
1
Figure 2- 4 Dr il l Temp la te
3.Ro ute the cables to the cable hole and co nn ec t
the cor re sp on di ng p ower cable and video cable
4.Fix the cam era to the wall with the supplied
screws.
Adjusting Screw
Figure 2- 5 Fi x th e Ca me ra to the Wall
5. Adjust t he s urveillance angle.
1). Loosen No.3 adjusting screw to adjust the pan
position ( .
2).Tight en N o. 3 ad ju stin g sc rew.
3). Loosen No.2 adjusting screw to adjust the
tilting position( ).
4).Tight en N o. 2 ad ju stin g sc rew.
5). Loosen No.1 adjusting screw to adjust the
rotation position .
6).Tight en N o. 1 ad ju stin g sc rew.
0° ~ 360°)
0° ~ 90°
(0° ~ 360°)
360°
Figure 2- 6 3- ax is A dj ustment
360°
3
90°
2
1
Figure 2- 7 Dr il l Temp la te
3.Ro ute the cables to the cable hole and co nn ec t
the cor re sp on di ng cab le s.
4.Fix the ca me ra to the ceiling with the supplied
screws.
Figure 2- 8 Fi x th e Ca me ra to the Ceiling
5.Adjust t he s urveillance angle.
1).Loosen No.3 adjusting screw to adjust the
panning position (0° ).
~ 360°
2).Tight en N o. 3 ad ju stin g sc rew.
3).Loosen No.2 adjusting screw to adjust the
tilting position (0° ~ 90°).
4).Tight en N o. 2 ad ju stin g sc rew.
5).Loosen No.1 adjusting screw to adjust the
azimuth angle of the image (0° ~ 360°).
6).Tight en N o. 1 ad ju stin g sc rew.
360°
Figure 2- 9 3- ax is A dj ustment
6.Adjust t he zoom and the focus.
1).Output the image to t he m on it or .
2).Push fo rward to re mo ve the adjusting sheet
located on the bottom of the camera. See
figure be lo w.
3).Insert the re mo ved ad ju sting sheet to zo om
slot and fo cu s sl ot to ad ju st the zoom and the
foc us .
4).Put the adjusting sheet ba ck aft er t he
adjustm en t is d on e.
Focus
Zoom
Adjus ti ng S heet
Figure 2- 10 Focus and Zoom Adjustment
2.4 Power Supply
Figure 2- 11 T he Powe Cable & the Video Cable
Note:
Please make sure that the powe r ad ap ter is
com pati bl e wi th t he c am era, and the stan da rd
power s up pl y is 1 2V D C. Please refer t o th e
tec hn ic al s pe ci fi cation for more i nformation.
Loading...