AMD is a trademark of Advanced Micro
Devices, Inc. Bluetooth is a trademark
owned by its proprietor and used by
Hewlett-Packard Company under license.
Intel and Centrino are trademarks of Intel
Corporation in the U.S. and other countries.
Java is a U.S. trademark of Sun
Microsystems, Inc. Microsoft and Windows
are U.S. registered trademarks of Microsoft
Corporation.
The information contained herein is subject
to change without notice. The only
warranties for HP products and services are
set forth in the express warranty statements
accompanying such products and services.
Nothing herein should be construed as
constituting an additional warranty. HP shall
not be liable for technical or editorial errors
or omissions contained herein.
First Edition: January 2012
Document Part Number: 682530-001
Product notice
This reference guide describes features
that are common to most models. Some
features may not be available on your
computer.
To obtain the latest information in this
guide, contact support. For U.S. support, go
WARNING!To reduce the possibility of heat-related injuries or of overheating the computer, do not
place the computer directly on your lap or obstruct the computer air vents. Use the computer only on
a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft
surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to
contact the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer
and the AC adapter comply with the user-accessible surface temperature limits defined by the
International Standard for Safety of Information Technology Equipment (IEC 60950).
Video .................................................................................................................................................. 16
4 Power management ...................................................................................................................................... 20
Shutting down the computer ............................................................................................................... 20
Setting power options ......................................................................................................................... 21
Using power-saving states ................................................................................................. 21
Initiating and exiting Sleep ................................................................................ 21
Initiating and exiting Hibernation ....................................................................... 21
Using the power meter ....................................................................................................... 22
Using power plans ............................................................................................................. 22
Viewing the current power plan ......................................................................... 22
Selecting a different power plan ........................................................................ 22
Customizing power plans .................................................................................. 22
Setting password protection on wakeup ............................................................................ 23
Using HP Power Assistant (select models only) ................................................................................ 24
Using battery power ........................................................................................................................... 24
Finding additional battery information ................................................................................ 24
Using Battery Check .......................................................................................................... 25
Displaying the remaining battery charge ........................................................................... 25
Maximizing battery discharge time .................................................................................... 25
Appendix A Traveling with the computer ...................................................................................................... 76
Appendix B Troubleshooting resources ....................................................................................................... 78
Appendix C Electrostatic discharge .............................................................................................................. 79
Index ................................................................................................................................................................... 80
ix
x
1Introduction
This guide contains general information about HP notebook computers.
NOTE:Some of the features described in this guide may not be available on your computer.
Finding more information about your new computer
The following user guides and reference material are provided with your computer, either in print, on
the computer hard drive, or on an optical disc:
Setup Instructions poster—Guides you through setting up your computer and turning it on. The
●
poster is included in the box with the computer.
NOTE:See the poster for the location of your user guides and reference material.
Getting Started—Contains information about your computer, including product-specific features,
●
backup and recovery, maintenance, and specifications. To access the Getting Started guide on
your computer, select Start > Help and Support > User Guides.
To access this guide on the Web, go to the HP Business Support Center at
go/bsc.
Help and Support—Contains information about the operating system, drivers, troubleshooting
●
tools, and support. To access Help and Support, select Start > Help and Support. For U.S.
support, go to
Safety & Comfort Guide—Describes proper workstation setup and proper posture, health, and
●
work habits for computer users. It also provides important electrical and mechanical safety
information. To access this guide, select Start > Help and Support > User Guides. This guide
is also available on the Web at
●Regulatory, Safety and Environmental Notices—Contains safety and regulatory information, and
battery disposal information. To access the notices, select Start > Help and Support > UserGuides.
http://www.hp.com/go/contactHP. For worldwide support, go to
http://www.hp.com/ergo.
http://www.hp.com/
Finding more information about your new computer1
2Networking (select models only)
Your computer supports two types of Internet access:
●Wireless—See
Wired—See
●
Creating a wireless connection on page 2.
Connecting to a wired network on page 9.
NOTE:You must set up Internet service before you can connect to the Internet.
Creating a wireless connection
Your computer may be equipped with one or more of the following wireless devices:
Wireless local area network (WLAN) device
●
●HP Mobile Broadband Module (wireless wide area network (WWAN) device)
Bluetooth® device
●
For more information on wireless technology, see the information and website links provided in Help
and Support.
Identifying wireless and network status icons
IconNameDescription
Wireless (connected)Indicates that one or more wireless devices are on.
Wireless (disconnected)Indicates that all wireless devices are off.
HP Connection Manager
(select models only)
Wired network (connected)Indicates that one or more network devices are connected to the network.
Wired network (disabled/
disconnected)
2Chapter 2 Networking (select models only)
Opens HP Connection Manager, which enables you to create and manage
WWAN connections (select models only), and monitor the status of WLAN
and Bluetooth connections.
Indicates that all network devices are disabled in Windows® Control
Panel.
IconNameDescription
Network (connected)Indicates that one or more network devices are connected to a network.
Network (disconnected)Indicates that network devices are not connected to a network.
Network (disabled/
disconnected)
Indicates that no wireless connections are available.
Creating a wireless connection3
Turning wireless devices on or off
You can use the wireless button or HP Connection Manager (select models only) to turn on and turn
off wireless devices.
NOTE:A computer may have a wireless button, a wireless switch, or a wireless key on the
keyboard. The term wireless button is used throughout this guide to refer to all types of wireless
controls. See the Getting Started guide for information on identifying the type and location of the
wireless button on your computer.
To turn off wireless devices using HP Connection Manager:
Right-click the HP Connection Manager icon in the notification area, at the far right of the
▲
taskbar, and then click the power button next to the desired device.
– or –
Select Start>All Programs>Productivity and Tools > HP Connection Manager, and then
click the power button next to the desired device.
Using HP Connection Manager (select models only)
HP Connection Manager provides a central location for managing your wireless devices, an interface
for connecting to the Internet using HP Mobile Broadband, and an interface for sending and receiving
SMS (text) messages. HP Connection Manager allows you to manage the following devices:
●Wireless local area network (WLAN)/Wi-Fi
Wireless wide area network (WWAN)/HP Mobile Broadband
●
Bluetooth®
●
HP Connection Manager provides information and notifications on connection status, power status,
SIM details, and SMS messages. Status information and notifications are provided in the notification
area, at the far right of the taskbar.
To open HP Connection Manager:
Click the HP Connection Manager icon in the taskbar.
▲
– or –
Select Start>All Programs>Productivity and Tools > HP Connection Manager.
For more information, see the HP Connection Manager software Help.
Using operating system controls
The Network and Sharing Center allows you to set up a connection or network, connect to a network,
manage wireless networks, and diagnose and repair network problems.
To use operating system controls:
Select Start>Control Panel>Network and Internet>Network and Sharing Center.
▲
For more information, select Start > Help and Support.
4Chapter 2 Networking (select models only)
Using a WLAN
A wireless connection connects the computer to Wi-Fi networks, or WLANs. A WLAN is composed of
other computers and accessories that are linked by a wireless router or a wireless access point.
Connecting to an existing WLAN
1.Be sure that the WLAN device is on. (See Turning wireless devices on or off on page 4.)
2.Click the network icon in the notification area, at the far right of the taskbar.
3.Select your WLAN from the list.
NOTE:If no WLANs are listed, you may be out of range of a wireless router or access point.
NOTE:If you do not see the WLAN you want to connect to, click Open Network and Sharing
Center, and then click Set up a new connection or network. A list of options is displayed. You
can choose to manually search for and connect to a network, or you can create a new network
connection.
4.Click Connect.
If the network is a security-enabled WLAN, you are prompted to enter a network security code.
Type the code, and then click OK to complete the connection.
After the connection is made, you can place the mouse pointer over the network icon in the
notification area, at the far right of the taskbar, to verify the name and status of the connection.
NOTE:The functional range (how far your wireless signals travel) depends on WLAN
implementation, router manufacturer, and interference from other electronic devices or structural
barriers such as walls and floors.
Using a WLAN5
Setting up a new WLAN
Required equipment:
●A broadband modem (either DSL or cable) (purchased separately) (1) and high-speed Internet
service purchased from an Internet service provider (ISP)
●A wireless router (purchased separately) (2)
NOTE:Some cable modems include a built-in router. Check with your ISP to see if you need a
separate router.
The wireless computer (3)
●
The illustration shows an example of a wireless network installation that is connected to the Internet.
NOTE:When setting up a wireless connection, be sure that your computer and wireless router are
synchronized. To synchronize your computer and wireless router, turn your computer and wireless
router off and then back on.
As your network grows, additional wireless and wired computers can be connected to the network to
access the Internet.
For help in setting up your WLAN, see the information provided by your router manufacturer or your
ISP.
Protecting your WLAN
When you set up a WLAN or access an existing WLAN, always enable security features to protect
your network from unauthorized access. WLANs in public areas (hotspots) like coffee shops and
airports may not provide any security. If you are concerned about the security of your computer in a
hotspot, limit your network activities to e-mail that is not confidential and basic Internet surfing.
Wireless radio signals travel outside the network, so other WLAN devices can pick up unprotected
signals. You can take the following precautions to protect your WLAN:
Firewall—A firewall checks both data and requests for data that are sent to your network, and
●
discards any suspicious items. Firewalls are available in both software and hardware. Some
networks use a combination of both types.
Wireless encryption—Your computer supports three encryption protocols:
●
Wi-Fi Protected Access (WPA)
◦
Wi-Fi Protected Access II (WPA2)
◦
Wired Equivalent Privacy (WEP)
◦
6Chapter 2 Networking (select models only)
NOTE:HP recommends that you select WPA2, which is the most advanced of the three encryption
protocols. The use of WEP encryption is not recommended, because it can be overcome with little
effort.
Wi-Fi Protected Access (WPA) and Wi-Fi Protected Access II (WPA2) use security standards to
●
encrypt and decrypt data transmitted over the network. Both WPA and WPA2 dynamically
generate a new key for every packet, and they also generate a different set of keys for each
computer on the network. To accomplish this:
WPA uses Advanced Encryption Standard (AES) and Temporal Key Integrity Protocol
●Wired Equivalent Privacy (WEP) encrypts data with a WEP key before it is transmitted. Without
the correct key, others will not be able to use the WLAN.
Roaming to another network
When you move your computer within range of another WLAN, Windows attempts to connect to that
network. If the attempt is successful, your computer is automatically connected to the new network. If
Windows does not recognize the new network, follow the same procedure you used initially to
connect to your WLAN.
Using HP Mobile Broadband (select models only)
HP Mobile Broadband enables your computer to use wireless wide area networks (WWANs) to
access the Internet from more places and over larger areas than it can by using WLANs. Using HP
Mobile Broadband requires a network service provider, which in most cases is a mobile phone
network provider.
When used with mobile network provider service, HP Mobile Broadband gives you the freedom to
stay connected to the Internet, send e-mail, or connect to your corporate network whether you are on
the road or outside the range of Wi-Fi hotspots.
NOTE:You may need the HP Mobile Broadband Module serial number to activate mobile
broadband service. See the Getting Started guide for the location of the service label.
Some mobile network service providers require the use of a subscriber identity module (SIM). A SIM
contains basic information about you or your computer, such as a personal identification number
(PIN), as well as network information. Some computers include a preinstalled SIM. If the SIM is not
preinstalled, it may be included with the HP Mobile Broadband information provided with your
computer, or it may be provided separately by the mobile network service provider.
For information on inserting and removing the SIM, see
a SIM on page 8.
For additional information on HP Mobile Broadband and how to activate service with a preferred
mobile network service provider, see the HP Mobile Broadband information if it is included with your
computer. For additional information, see the HP website at
(select regions/countries only).
Inserting a SIM on page 8 and Removing
http://www.hp.com/go/mobilebroadband
Using HP Mobile Broadband (select models only)7
Inserting a SIM
NOTE:To identify the SIM slot location, see the Getting Started guide.
1.Shut down the computer. If you are not sure whether the computer is off or in Hibernation, turn
the computer on by pressing the power button. Then shut down the computer through the
operating system.
2.Close the display.
3.Disconnect all external devices connected to the computer.
4.Unplug the power cord from the AC outlet.
5.Remove the battery if the computer contains a user-replaceable battery.
6.Insert the SIM into the SIM slot, and gently press the SIM into the slot until it is firmly seated.
CAUTION:When inserting a SIM, position the card to match the icon next to the SIM slot on
the computer. If a SIM is inserted incorrectly, it could damage the SIM and the SIM connector.
To reduce the risk of damage to the connector, use minimal force when inserting a SIM.
7.Replace the battery.
NOTE:HP Mobile Broadband is disabled if the battery is not replaced.
8.Reconnect external power and external devices.
9.Turn on the computer.
Removing a SIM
NOTE:To identify the SIM slot location, see the Getting Started guide.
1.Shut down the computer. If you are not sure whether the computer is off or in Hibernation, turn
the computer on by pressing the power button. Then shut down the computer through the
operating system.
2.Close the display.
3.Disconnect all external devices connected to the computer.
4.Unplug the power cord from the AC outlet.
5.Remove the battery if the computer contains a user-replaceable battery.
6.Press in on the SIM, and then remove it from the slot.
7.Replace the battery.
8.Reconnect external power and external devices.
9.Turn on the computer.
8Chapter 2 Networking (select models only)
Using GPS (select models only)
Your computer may be equipped with a Global Positioning System (GPS) device. GPS satellites
deliver location, speed, and direction information to GPS-equipped systems.
For more information, see the HP GPS and Location software Help.
Using Bluetooth wireless devices
A Bluetooth device provides short-range wireless communications that replace the physical cable
connections that traditionally link electronic devices such as the following:
Computers
●
Phones
●
Imaging devices (cameras and printers)
●
Audio devices
●
Bluetooth devices provide peer-to-peer capability that allows you to set up a personal area network
(PAN) of Bluetooth devices. For information on configuring and using Bluetooth devices, see the
Bluetooth software Help.
Bluetooth and Internet Connection Sharing (ICS)
HP does not recommend setting up one computer with Bluetooth as a host and using it as a gateway
through which other computers may connect to the Internet. When two or more computers are
connected using Bluetooth, and Internet Connection Sharing (ICS) is enabled on one of the
computers, the other computers may not be able to connect to the Internet using the Bluetooth
network.
The strength of Bluetooth is in synchronizing information transfers between your computer and
wireless devices including cellular phones, printers, cameras, and PDAs. The inability to consistently
connect two or more computers to share the Internet through Bluetooth is a limitation of Bluetooth
and the Windows operating system.
Connecting to a wired network
Using a modem (select models only)
A modem must be connected to an analog telephone line using a 6-pin, RJ-11 modem cable
(purchased separately). In some countries or regions, a specific modem cable adapter is also
required. Jacks for digital PBX systems may resemble analog telephone jacks, but they are not
compatible with the modem.
WARNING!To reduce the risk of electric shock, fire, or damage to the equipment, do not plug a
modem or telephone cable into the RJ-45 (network) jack.
If the modem cable contains noise suppression circuitry (1), which prevents interference from TV and
radio reception, orient the circuitry end of the cable (2) toward the computer.
Using GPS (select models only)9
Connecting a modem cable
1.Plug the modem cable into the modem jack (1) on the computer.
2.Plug the modem cable into the RJ-11 telephone wall jack (2) or a route (not illustrated).
10Chapter 2 Networking (select models only)
Connecting a country- or region-specific modem cable adapter
Telephone jacks vary by country or region. To use the modem and the modem cable outside the
country or region in which you purchased the computer, you must obtain a country- or region-specific
modem cable adapter.
To connect the modem to an analog telephone line that does not have an RJ-11 telephone jack,
follow these steps:
1.Plug the modem cable into the modem jack (1) on the computer.
2.Plug the modem cable into the modem cable adapter (2).
3.Plug the modem cable adapter (3) into the telephone wall jack.
Selecting a location setting
Viewing the current location selection
1.Select Start > Control Panel.
2.Click Clock, Language, and Region.
3.Click Region and Language.
4.Click the Location tab to display your location.
Connecting to a wired network11
Adding new locations when traveling
On a new computer, the only location setting available to the modem is a location setting for the
country or region in which you purchased the computer. As you travel to different countries or
regions, set the internal modem to a location setting that meets the operating standards of the country
or region in which you are using the modem.
As you add new location settings, they are saved by the computer so that you can switch among
settings at any time. You can add multiple location settings for any country or region.
CAUTION:To reduce the risk of losing your home country or region settings, do not delete your
current modem country or region settings. To enable modem use in other countries or regions while
preserving your home country or region configuration, add a new configuration for each location in
which you will use the modem.
CAUTION:To reduce the risk of configuring the modem in a way that violates the
telecommunications regulations and laws of the country or region you are visiting, select the country
or region in which the computer is located. The modem may not function properly if the correct
country or region selection is not made.
1.Select Start > Devices and Printers.
2.Right-click the device that represents your computer, and click Modem settings.
NOTE:You must set up an initial (current) location area code before you can view the Dialing
Rules tab. If you do not have a location already set up, you are prompted to enter the location
when you click Modem settings.
3.Click the Dialing Rules tab.
4.Click New. The New Location window opens.
5.In the Location name box, type a name (such as home or work) for the new location setting.
6.Select a country or region from the Country/region list. (If you select a country or region that is
not supported by the modem, the country/region selection for USA or UK is displayed.)
7.Enter the area code, a carrier code (if necessary), and the number for an outside line (if
necessary).
8.Next to Dial using, click Tone or Pulse.
9.Click OK to save your new location setting.
10. Do one of the following:
To set your new location setting as the current location, click OK.
●
To select another location setting as the current location setting, select your preference
●
from the settings in the Location list, and then click OK.
NOTE:You can use the preceding procedure to add location settings for places within your
own country or region as well as in other countries or regions. For example, you could add a
setting named Work that includes dialing rules for accessing an outside line.
12Chapter 2 Networking (select models only)
Connecting to a local area network (LAN) (select models only)
Connecting to a LAN requires an 8-pin, RJ-45 network cable (purchased separately). If the network
cable contains noise suppression circuitry (1), which prevents interference from TV and radio
reception, orient the circuitry end of the cable (2) toward the computer.
To connect the network cable:
1.Plug the network cable into the network jack (1) on the computer.
2.Plug the other end of the network cable into a network wall jack (2) or a router (not illustrated).
WARNING!To reduce the risk of electric shock, fire, or damage to the equipment, do not plug a
modem cable or telephone cable into an RJ-45 (network) jack.
Connecting to a wired network13
3Multimedia
Your computer may include the following multimedia components:
●Integrated speaker(s)
Integrated microphone(s)
●
Integrated webcam
●
Preinstalled multimedia software
●
Multimedia buttons or keys
●
Using the media activity controls
Depending on your computer model, you may have the following media activity controls that allow
you to play, pause, fast forward, or rewind a media file:
Audio
Media buttons
●
●Media hotkeys (specific keys pressed in combination with the fn key)
●Media keys
See the Getting Started guide for information about your computer's media activity controls.
Your computer provides a variety of audio-related functions:
Play music.
●
Record sound.
●
●Download music from the Internet.
●Create multimedia presentations.
Transmit sound and images with instant messaging programs.
●
Stream radio programs.
●
Create (burn) audio CDs using the installed optical drive (select models only) or an optional
●
external optical drive (purchased separately).
14Chapter 3 Multimedia
Adjusting the volume
Depending on your computer model, you can adjust the volume using the following:
●Volume buttons
Volume hotkeys (specific keys pressed in combination with the fn key)
●
Volume keys
●
WARNING!To reduce the risk of personal injury, adjust the volume before putting on headphones,
earbuds, or a headset. For additional safety information, see the Regulatory, Safety and
Environmental Notices.
NOTE:Volume can also be controlled through the operating system and some programs.
NOTE:See the Getting Started guide for information on what type of volume controls your computer
has.
Checking audio functions on the computer
NOTE:For best results when recording, speak directly into the microphone and record sound in a
setting free of background noise.
To check the audio functions on your computer, follow these steps:
1.Select Start > Control Panel > Hardware and Sound > Sound.
2.When the Sound window opens, click the Sounds tab. Under Program Events, select any
sound event, such as a beep or alarm, and click the Test button.
You should hear sound through the speakers or through connected headphones.
To check the recording functions on your computer, follow these steps:
1.Select Start > All Programs > Accessories > Sound Recorder.
2.Click Start Recording and speak into the microphone. Save the file to your desktop.
3.Open a multimedia program and play back the sound.
To confirm or change the audio settings on your computer, select Start > Control Panel > Hardware
and Sound > Sound.
To check the recording functions on your computer, follow these steps:
1.Select Start > All Programs > Accessories > Sound Recorder.
2.Click Start Recording and speak into the microphone. Save the file to your desktop.
3.Open a multimedia program and play back the sound.
To confirm or change the audio settings on your computer, select Start > Control Panel >
Audio.
Webcam (select models only)
Some computers include an integrated webcam. With the preinstalled software, you can use the
webcam to take a photo or record a video. You can preview and save the photo or video recording.
Webcam (select models only)15
Video
The webcam software enables you to experiment with the following features:
Capturing and sharing video
●
Streaming video with instant message software
●
Taking still photos
●
Administrators can set the security level for Face Recognition in the Security Manager Setup Wizard
or HP ProtectTools Administrative Console. For more information, see the HP ProtectTools GettingStarted guide or the Face Recognition software Help.
For information on how to access the webcam, see the Getting Started guide. For information on
using the webcam, select Start > Help and Support.
Your computer may have one or more of the following external video ports:
VGA
●
HDMI (High Definition Multimedia Interface)
●
DisplayPort
●
NOTE:See the Getting Started guide for information about your computer's video ports.
VGA
The external monitor port, or VGA port, is an analog display interface that connects an external VGA
display device such as an external VGA monitor or a VGA projector to the computer.
To connect a VGA display device, connect the device cable to the external monitor port.
▲
NOTE:For product-specific instructions on switching the screen image, see your Getting
Started guide.
16Chapter 3 Multimedia
DisplayPort
The DisplayPort connects the computer to an optional video or audio device, such as a high-definition
television, or to any compatible digital or audio component. The DisplayPort delivers higher
performance than the VGA external monitor port and improves digital connectivity.
NOTE:To transmit video and/or audio signals through the DisplayPort, you need a DisplayPort
cable (purchased separately).
One DisplayPort device can be connected to the DisplayPort port on the computer. The information
displayed on the computer screen can be simultaneously displayed on the DisplayPort device.
To connect a video or audio device to the DisplayPort:
1.Connect one end of the DisplayPort cable to the DisplayPort port on the computer.
2.Connect the other end of the cable to the video device, and then see the device manufacturer’s
instructions for additional information.
NOTE:To remove the device cable, press down on the connector latch to disconnect it from the
computer.
NOTE:For product-specific instructions on switching the screen image, see your Getting Started
guide.
Video17
HDMI
The HDMI port connects the computer to an optional video or audio device, such as a high-definition
television, or to any compatible digital or audio component.
NOTE:To transmit video and/or audio signals through the HDMI port, you need an HDMI cable
(purchased separately).
One HDMI device can be connected to the HDMI port on the computer. The information displayed on
the computer screen can be simultaneously displayed on the HDMI device.
To connect a video or audio device to the HDMI port:
1.Connect one end of the HDMI cable to the HDMI port on the computer.
2.Connect the other end of the cable to the video device, and then see the device manufacturer’s
instructions for additional information.
NOTE:For product-specific instructions on switching the screen image, see your Getting Started
guide.
Configuring audio for HDMI
To configure HDMI audio, first connect an audio or video device, such as a high-definition TV, to the
HDMI port on your computer. Then configure the default audio playback device as follows:
1.Right-click the Speakers icon in the notification area, at the far right of the taskbar, and then
click Playback devices.
2.On the Playback tab, click either Digital Output or Digital Output Device (HDMI).
3.Click Set Default, and then click OK.
To return audio to the computer speakers, follow these steps:
1.Right-click the Speakers icon in the notification area, at the far right of the taskbar, and then
click Playback devices.
2.On the Playback tab, click Speakers.
3.Click Set Default, and then click OK.
18Chapter 3 Multimedia
Loading...
+ 64 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.