Henny Penny HEC-103 Installation Manual

Model HEC-103/104/123/124

SECTION 2. INSTALLATION

2-1. INTRODUCTION This section provides the installation instructions for the Henny Penny

heated express cabinet.

Installation of this unit should be performed only by a qualified
service technician.

Do not puncture the skin of the unit with drills or screws as
component damage or electrical shock could result.

2-2. UNP ACKING

The Henny Penny heated express cabinet has been tested, inspected,
and expertly packed to insure arrival at its destination in the best
possible condition. The unit has been bolted to wooden skid. All
items have been packed and taped inside of the unit. The unit is then
packed inside a triple wall corrugated carton with sufficient padding to
withstand normal shipping treatment.

Any shipping damages should be noted in the presence of the
delivery agent and signed prior to his or her departure.

T o remove the Henny Penny cabinet from the carton, you should:

1. Carefully cut banding straps.

2. Open flaps of carton and remove packing.

3. Lift carton from unit.

4. Remove four bolts mounting the merchandiser to the skid.

5. Install optional legs on units if available.

To avoid breaking side glass or damaging unit, lay unit on its
back, not on its side, when installing legs. Install legs before
installing the shelves.

503 2-1

Model HEC-103/104/123/124

2-2. UNP ACKING

(Continued)

Figure 2-1

Figure 2-2

6A.Unpack and install shelves.

a. Hook the shelf brackets in the slots in the back, interior of unit.

See next pages (Figure 2-5 & 2-6) for proper slot arrangement for
either 2, 3 or 4 shelf units.

b. Pull the cover off the receptacles on each side of the shelves.

Figure 2-1.

c. Line up the prongs on the plug with the holes in the receptacle,

and firmly push the plugs into the receptacles. Figure 2-2.

The plugs must fit firmly into the receptacles for the lights and shelf
heaters to operate.

6B. CE UNITS-Upack and install shelves.

a. Hook the shelf brackets in the slots in the back, interior of unit.

See next pages (Figure 2-5 & 2-6) for proper slot arrangement for
either 2, 3 or 4 shelf units.

b. Using a Phillip’s head screwdriver, remove the screw securing

the shelf plug cover and remove the cover. Figure 2-3.

c. Pull the cover off the receptacles on each side of the shelves.

Figure 2-1.

d. Line up the prongs on the plug with the holes in the receptacle,

and firmly push the plugs into the receptacles. Figure 2-2.

e. Insert the tab on the shelf plug cover into the slot on the back

panel and secure the cover in place using the screw previously
removed. Figure 2-4.

Figure 2-3

Figure 2-4

7. Install fluorescent lamps. See Installing or Replacing Fluorescent
Lamps Section.

8. Remove the bottom inserts and pull cardboard packing from around
elements in bottom of unit.

To avoid fire, remove the 3 corrugated shipping supports
located beneath these inserts, all visible packing material, tape,
and the unpacking instructions, prior to operation.

9. Peel off any protective covering from the exterior of the cabinet.

Take care when moving the cabinet to prevent personal
injury.

10. Once the shelves and shelf lamps are installed, and the packing
material removed, the unit is ready for operation.

2-2 705

Model HEC-103/104/123/124

2-3. HEC 3 & 4 SHELF INST ALL- The drawing below is the slot arrangement (right and left) for
ATION INSTRUCTIONS the brackets of the shelves of the HEC. The lines point to the

slot that the top prong of the bracket fits into.

Top shelf-4 shelf unit

Top shelf-3 shelf unit

3rd shelf-4 shelf unit

2nd shelf-3 shelf unit

2nd shelf-4 shelf unit

1st shelf-3 shelf unit

1st shelf-4 shelf unit

Figure 2-5

603 2-3