Henny Penny HDS-300 Owner’s Manual
Henny Penny
Holding Display Station
Model HDS-300
OPERAT OR’S MANUAL
Model HDS-300
LIMITED WARRANTY FOR HENNY PENNY EQUIPMENT
Subject to the following conditions, Henny Penny Corporation makes the following limited warranties to the original
purchaser only for Henny Penny appliances and replacement parts:
NEW EQUIPMENT: Any part of a new appliance, except baskets, lamps, and fuses, which proves to be defective in
material or workmanship within two (2) years from date of original installation, will be repaired or replaced without
charge F .O.B. factory , Eaton, Ohio, or F .O.B. authorized distributor . Baskets will be repaired or replaced for ninety (90)
days from date of original installation. Lamps and fuses are not covered under this Limited W arranty. T o validate this
warranty, the registration card for the appliance must be mailed to Henny Penny within ten (10) days after installation.
FILTER SYSTEM: Failure of any parts within a fryer filter system caused by the use of the non-OEM filters or
other unapproved filters is not covered under this Limited Warranty.
REPLACEMENT PARTS: Any appliance replacement part, except lamps and fuses, which proves to be defective in
material or workmanship within ninety (90) days from date of original installation will be repaired or replaced without
charge F .O.B. factory , Eaton, Ohio, or F .O.B. authorized distributor .
The warranty for new equipment covers the repair or replacement of the defective part and includes labor charges and
maximum mileage charges of 200 miles round trip for a period of one (1) year from the date of original installation.
The warranty for replacement parts covers only the repair or replacement of the defective part and does not include any
labor charges for the removal and installation of any parts, travel, or other expenses incidental to the repair or replacement of
a part.
EXTENDED FRYPOT WARRANTY: Henny Penny will replace any frypot that fails due to manufacturing or workmanship
issues for a period of up to seven (7) years from date of manufacture. This warranty shall not cover any frypot that fails due to
any misuse or abuse, such as heating of the frypot without shortening.
0 TO 3 YEARS: During this time, any frypot that fails due to manufacturing or workmanship issues will
be replaced at no charge for parts, labor, or freight. Henny Penny will either install a new frypot at no cost or
provide a new or reconditioned replacement fryer at no cost.
3 TO 7 YEARS: During this time, any frypot that fails due to manufacturing or workmanship issues will
be replaced at no charge for the frypot only . Any freight charges and labor costs to install the new frypot as
well as the cost of any other parts replaced, such as insulation, thermal sensors, high limits, fittings, and
hardware, will be the responsibility of the owner.
Any claim must be presented to either Henny Penny or the distributor from whom the appliance was purchased. No
allowance will be granted for repairs made by anyone else without Henny Penny’s written consent. If damage occurs during
shipping, notify the sender at once so that a claim may be filed.
THE ABOVE LIMITED WARRANTY SETS FORTH THE SOLE REMEDY AGAINST HENNY PENNY FOR ANY
BREACH OF WARRANTY OR OTHER TERM. BUYER AGREES THAT NO OTHER REMEDY (INCLUDING CLAIMS
FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES) SHALL BE AVAILABLE.
The above limited warranty does not apply (a) to damage resulting from accident, alteration, misuse, or abuse; (b) if the
equipment’s serial number is removed or defaced; or (c) for lamps and fuses. THE ABOVE LIMITED WARRANTY IS EXPRESSL Y IN LIEU OF ALL OTHER W ARRANTIES, EXPRESS OR IMPLIED, INCLUDING MERCHANT ABILITY AND FITNESS, AND ALL OTHER W ARRANTIES ARE EXCLUDED. HENNY PENNY NEITHER ASSUMES NOR AUTHORIZES ANY
PERSON TO ASSUME FOR IT ANY OTHER OBLIGA TION OR LIABILITY.
Revised 01/01/07
FM05-039-C
Revised 02-15-07
Model HDS-300
T ABLE OF CONTENTS
Section Page
Section 1. INTRODUCTION.........................................................................................................1-1
1-1. Holding Display Station.......................................................................................1-1
1-2. Features .............................................................................................................1-1
1-3. Proper Care .......................................................................................................1-1
1-4. Assistance ..........................................................................................................1-1
1-5. Safety.................................................................................................................1-2
Section 2. INST ALLATION...........................................................................................................2-1
2-1. Introduction ........................................................................................................2-1
2-2. Unpacking ..........................................................................................................2-1
2-3. Assembly ...........................................................................................................2-2
2-4. Electrical ............................................................................................................2-8
2-5. Voltage Set-up....................................................................................................2-8
2-6. Optional Wireway Channel (“Chimney”) Mounting Instructions ............................2-9
Section 3. OPERA TION.................................................................................................................3-1
3-1. Introduction ........................................................................................................3-1
3-2. Operating Controls & Components .....................................................................3-1
3-3. Start-Up.............................................................................................................3-2
3-4. Operation with Product ......................................................................................3-2
3-5. Shut-Down & Clean-Up .....................................................................................3-3
3-6. Light Bulb Replacement ......................................................................................3-5
Section 4. TROUBLESHOOTING.................................................................................................4-1
4-1. Troubleshooting Guide ........................................................................................4-1
Distributor Lists - Domestic and International
i 406
Model HDS-300
SECTION 1. INTRODUCTION
1-1. HOLDING DISPLA Y The Henny Penny Holding Display Station is a basic unit of food
ST ATION processing equipment used to display the food product and
maintain the temperature of hot and cold foods in the commercial
food service operation. This highly efficient, quality-built cabinet will
keep hot foods and cold foods at proper holding temperatures.
The Henny Penny Holding Display Stations have no doors
which allows easy access to the food products from both front
and back of the unit.
As of August 16, 2005, the W aste Electrical and Electronic
Equipment directive went into effect for the European Union.
Our products have been evaluated to the WEEE directive. W e
have also reviewed our products to determine if they comply
with the Restriction of Hazardous Substances directive (RoHS)
and have redesigned our products as needed in order to
comply . T o continue compliance with these directives, this unit
must not be disposed as unsorted municipal waste. For proper
disposal, please contact your nearest Henny Penny distributor.
1-2. FEA TURES • Hot well for holding steam pans
• Dry heat in top section
• Easy to keep clean
• Cold well for holding pans of cold product
• French fry station with dividers
• Electronic controls including timers for the food product
• Large shelves with dividers for holding paper products
• T op section holds three 18 x 26 bun pans
• One unit for either 208 or 240 volt applications-the controls
automatically adjust for the differnce in power
1-3. PROPER CARE As in any unit of food service equipment, the Henny Penny Holding
Display Station does require care and maintenance. Requirements
for the maintenance and cleaning are contained in this manual and
must become a regular part of the operation of the unit at all times.
1-4. ASSISTANCE Should you require outside assistance, just call your local
independent Henny Penny distributor in your area, call Henny
Penny Corp. at 1-800-417-8405 toll free or 1-937-456-8405, or
go to Henny Penny online at www .hennypenny.com.
207 1-1
Model HDS-300
1-3. SAFETY The only way to ensure safe operation of the Henny Penny Holding
Display Station is to fully understand the proper installation,
operation, and maintenance procedures. The instructions in this
manual have been prepared to aid you in learning the proper
procedures. Where information is of particular importance or is
safety related, the words NOTICE, CAUTION, or W ARNING
are used. Their usage is described below .
SAFETY ALER T SYMBOL is used with DANGER,
W ARNING, or CAUTION which indicates a personal injury
type hazard.
NOTICE is used to highlight especially important information.
CAUTION used without the safety alert symbol indicates
a potentially hazardous situation which, if not avoided, may
result in pr operty damage.
CAUTION indicates a potentially hazardous situation
which, if not avoided, may result in minor or moderate
injury.
The word WARNING is used to alert you to a pr ocedure,
that if not performed properly , might cause personal
injury.
1-2 605
Model HDS-300
SECTION 2. INSTALLATION
2-1. INTRODUCTION This section provides the installation instructions for the Henny
Penny Holding Display Station.
Installation of this unit should be performed only by a qualified
service technician.
Do not puncture the skin of the unit with drills or
screws as component damage or electrical shock
could result.
2-2. UNP ACKING The Henny Penny Holding Display Station has been tested,
inspected, and expertly packed to ensure arrival at its destination in
the best possible condition. The unit is shipped in 3 separate cartons
and have been bolted to a wooden skid. The units are then
packed inside a triple wall corrugated carton with sufficient padding
to withstand normal shipping treatment.
Any shipping damages should be noted in the presence of the
delivery agent and signed prior to his or her departure.
T o remove the Henny Penny Holding Display Station from the
carton, you should:
1. Carefully cut banding straps and remove units from packaging.
Be sure to keep the owners manual from the Randell refrigeration unit when unpacking the unit. Important warranty information is contained in the manual.
The data plate for the Randell refrigeration unit is located on the
mechanical base, by the compressor.
605 2-1
Loading...