Henny Penny EEG-241 Installation Manual

OPERATOR’S

MANUAL

EVOLUTION ELITE™ (Gas)

REDUCED OIL CAPACITY OPEN FRYER

MODEL

EEG-241 EEG-242 EEG-243 EEG-244

Read instructions before operating the appliance

HENNY PENNY

OPEN FRYER

Fryer must be installed and used in such a way to prevent water from contacting the shortening.

This appliance is not intended to be operated by means of an external timer or a separate remote control system.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

This manual should be retained in a convenient location for future reference.

A wiring diagram for this appliance is located on the inside of the door.

Post in a prominent location, instructions to be followed in event user smells gas. This information shall be obtained by consulting the local gas supplier.

Do not obstruct the ow of combustion and ventilation air. Adequate clearance must be left all around appliance for sufcient air to the combustion chamber.

The Model EEG-10X open fryer is equipped with a continuous pilot. But the open fryer cannot be

operated without electric power, and no attempt should be made to operate the fryer during a power outage. The unit will automatically return to normal operation when power is restored.

To avoid a re, keep appliance area free and clear from combustibles.

Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death. Read the installation, operating,

and maintenance instructions thoroughly before installing or servicing this

equipment.

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE

VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER

APPLIANCE. FIRE OR EXPLOSION COULD RESULT.

Technical Data for CE/AGA Marked Products

Nominal Heat Input: Natural (I2H) = 19,8, kW (67,560 Btu/h)

(Net) Natural (I

Natural (I2E+) = 19.8 kW (67,560 Btu/h)

Natural (I

Liquid Propane (I3P) = 19,8, kW (67,560 Btu/h)

Nominal Heat Input: Natural (I2H) = 21,98 kW (75,000 Btu/h) (79.13 MJ/h)

(Gross) Natural (I2E) = 21,98 kW (75,000 Btu/h)

Natural (I

Natural (I2L) = 21,98 kW (75,000 Btu/h)

Natural (I

Liquid Propane (I3P) = 21,98 kW (75,000 Btu/h) (79.13 MJ/h)

) = 19.8 kW (67,560 Btu/h)

2HS

+) = 21,98 kW (75,000 Btu/h)

) = 21,98 kW (75,000 Btu/h)

2HS

Supply Pressure: Natural (I Natural (I

) = 20 mbar (2.0 kPa)

) = 20 mbar

Natural (I2E+) = 20/25 mbar

Natural (I2L) = 25 mbar

Natural (I

) = 25 mbar

2HS

Liquid Propane (I3P) = 30/37/50 mbar (3.0/3.7/5.0 kPa)

Test Point Pressure: Natural (I

Natural (I

) = 8.7 mbar (.87 kPa)

) = 8,7 mbar

+) = N/A

) = 8.7 mbar

2HS

Liquid Propane (I3P) = 25 mbar (2.5 kPa)

Injector Size: Natural (I2H) = 2.08 mm

Natural (I2E) = 2.08 mm

Natural (I2E+) = 1.70 mm

Natural (I

Liquid Propane (I

) = 2.30 mm

2HS

) = 1.30 mm

This appliance must be installed in accordance with the manufacturer’s instructions and the regulations in force and only used in a suitable ventilated location. Read the instructions fully before installing or using the appliance.

Noise generated from this equipment is less than 70 dB(A)

TABLE OF CONTENTS

INTRODUCTION ...............................................................................................................1

1-1 Safety ....................................................................................................................1

1-2 Introduction ........................................................................................................... 3

1-3 Features ................................................................................................................. 3

1-4 Proper Care ...........................................................................................................3

1-5 Assistance..............................................................................................................3

INSTALLATION .................................................................................................................4

2-1 Introduction ........................................................................................................... 4

2-2 Unpacking ............................................................................................................. 4

2-3 Selecting the Fryer Location ................................................................................. 5

2-4 Leveling the Fryer ................................................................................................. 5

2-5 Ventilation of Fryer ...............................................................................................5

2-6 Gas Supply ............................................................................................................ 6

2-7 Gas Leak Test ........................................................................................................ 9

2-8 Gas Pressure Regulator Setting ............................................................................. 9

2-9 Electrical Requirements ........................................................................................9

2-10 Motor Bearings ...................................................................................................10

2-11 Lighting and Shutdown of the Burners ............................................................... 10

2-12 Testing the Fryer .................................................................................................10

2-13 Dimensions.......................................................................................................... 11

OPERATION .....................................................................................................................15

3-1 Operating Components .......................................................................................15

3-2 Set-Up Mode ....................................................................................................... 19

3-3 Filling or Adding Oil ........................................................................................... 20

3-4 Morning Start-Up Procedures ............................................................................. 21

3-5 Basic Operation ................................................................................................... 22

3-6 Idle Mode ............................................................................................................ 22

3-7 Oil Guardian™ (Auto Top-Off) ..........................................................................23

3-8 Selecting a Product with a Different Setpoint .....................................................23

3-9 Replacing the JIB ................................................................................................ 23

3-10 Model EEG-241 Oil Reservoir ...........................................................................24

3-11.a Manual SmartFilter Express™ ............................................................................ 25

3-11.b Auto-SmartFilter Express™ ................................................................................27

3-12.a Manual - Daily Filtering .....................................................................................29

3-12.b Auto - Daily Filtering ..........................................................................................31

3-13.a Manual - Discarding Oil from Vat Using Optional Discard Shuttle ...................33

3-13/b Auto - Discarding Oil from Vat Using Optional Discard Shuttle .......................34

3-14 Discarding Oil from Vat Using Optional Bulk Oil Dispose System ................... 35

3-15 Discarding Oil Using Optional Oil Discard Shuttle-ODS-400 ........................... 36

3-16 Discarding Oil Using Optional Oil Discard Shuttle-ODS-450 ........................... 38

3-17 Changing the Filter Pad....................................................................................... 41

3-18 Removing and Cleaning Basket Rest .................................................................. 44

3-19.a Clean-Out Mode - Manual .................................................................................. 44

3-19.b Clean-Out Mode - Smart Touch .......................................................................... 47

3-20 Check/Replace Filter Drain Pan O-Rings ........................................................... 50

3-21 Info Button Stats .................................................................................................51

3-22 Filter Button Stats ............................................................................................... 51

3-23 Preventive Maintenance Schedule ...................................................................... 52

3-24 Clean Blower & Vents .........................................................................................53

iApril 2015

TABLE OF CONTENTS

INFORMATION MODE ...................................................................................................54

4-1 Information Mode Details ................................................................................... 54

PRODUCT PROGRAM MODE .......................................................................................59

5-1 Modifying Product Settings ................................................................................59

LEVEL 2 PROGRAMMING .............................................................................................62

6-1 Special Program Mode ........................................................................................ 62

6-2 Do Not Disturb .................................................................................................... 70

6-3 Clock Set ............................................................................................................. 71

6-4 Data Logging, Heat Control, Tech, Stat, and Filter Control Mode ..................... 71

TROUBLESHOOTING .....................................................................................................72

7-1 Troubleshooting Guide ........................................................................................72

7-2 Error Codes .........................................................................................................74

iiMarch 2014

SECTION 1: INTROduCTION

1-1

SAFETY

The instructions in this manual have been prepared to aid you

in learning the proper procedures for your equipment. Where

information is of particular importance or is safety related, the words NOTICE, CAUTION, or WARNING are used. Their usage is described below.

If a problem occurs during the rst operation of a new unit,

recheck the Installation Section of the Operator’s Manual.

Before troubleshooting, always recheck the Operation

Section of the Operator’s Manual.

Where information is of particular importance or is safety related, the words DANGER, WARNING, CAUTION, or NOTICE are

used. Their usage is described as follows:

SAFETY ALERT SYMBOL is used with DANGER,

WARNING or CAUTION which indicates a personal injury type hazard.

NOTICE is used to highlight especially important information.

CAUTION used without the safety alert symbol

indicates a potentially hazardous situation which, if not avoided, may result in property damage.

CAUTION used with the safety alert symbol indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury.

WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

DANGER INDICATES AN IMMINENTLY HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, WILL RESULT IN DEATH OR SERIOUS INJURY.

1March 2014

1-1.

SAFETY

(CONT.)

Equipotential Ground Symbol

Waste Electrical and Electronic Equipment (WEEE) Symbol

Shock Hazard Symbols

Hot Surface Symbols

2March 2014

1-2.

INTRODUCTION

The Henny Penny open fryer is a basic unit of food processing equipment

designed to cook foods better and easier. The micro computer-based design helps make this possible. This unit is used only in institutional and

commercial food service operations, and operated by qualied personnel.

• As of August 16, 2005, the Waste Electrical and Electronic

Equipment directive went into effect for the European Union. Our

products have been evaluated to the WEEE directive. We have also reviewed our products to determine if they comply with the Restriction of Hazardous Substances directive (RoHS) and have redesigned our products as needed in order to comply. To continue compliance with these directives, this unit must not be disposed as unsorted municipal waste. For proper disposal, please contact your nearest Henny Penny distributor.

1-3.

FEATURES

1-4.

PROPER CARE

• Easily cleaned

• Uses 40% less oil

• Full vat or split vat

• Computer control

• Stainless steel construction

• Automatic oil top off

• Self-diagnostic system built into controls

• Built in lter with automatic ltration

• Propane or natural gas; 75,000 BTU/vat (21.97 kw)

As in any unit of food service equipment, the Henny Penny open fryer does require care and maintenance. Requirements for the

maintenance and cleaning are contained in this manual and must become a regular part of the operation of the unit at all times.

Contact a qualied service technician in case of major maintenance

or repairs to the unit.

1-5.

ASSISTANCE

Should you require outside assistance, call your local independent

distributor in your area, or call Henny Penny Corp. at 1-800-417-8405 or 1-937-456-8405.

3March 2014

SECTION 2: INSTALLATION

2-1.

INTRODUCTION

2-2.

UNPACKING

This section provides the installation and unpacking instructions for the

Henny Penny Evolution Elite

Installation of this unit should be performed only by a qualied service

Do not puncture the fryer with any objects such as drills or screws as

component damage or electrical shock could result.

Any shipping damage should be noted in the presence of the delivery agent

and signed prior to his or her departure.

fryer.

technician.

1. Cut and remove the metal bands from the carton.

2. Remove carton lid and lift the main carton off the fryer.

3. Remove corner packing supports (4).

4. Cut the stretch lm from around the carrier/rack box and remove it

from the top of the fryer lid.

5. Cut and remove the metal bands holding the fryer to the pallet, and

remove fryer from pallet.

Remove lter drain pan and BIB shelf from fryer before removing fryer from

pallet or damage to the unit could result. Figure 1.

Take care when moving the fryer to prevent personal injury. The fryer

weighs approximately 600 lbs. (272 kg) to 800 lbs. (363 kg).

4March 2014

2-3.

SELECTING THE

FRYER LOCATION

The proper location of the fryer is very important for operation, speed, and convenience. The location of the open fryer should allow clearances for servicing and proper operation. Choose a location which will provide

easy loading and unloading without interfering with the nal assembly of food orders. Operators have found that frying from raw to nish, and

holding the product in warmers provides fast continuous service. Keep in mind, the best efciency will be obtained by a straight line operation,

i.e. raw in one side and nished out the other side. Order assembly can be moved away with only a slight loss of efciency.

To avoid re, install the open fryer with minimum clearance from all

combustible materials, 2 inches (5.08 cm) from the side and 4 inches

(10.16 cm) from the back. Minimum clearance from all non-combustible materials, 0 inches (0.00 cm) from the side and 0 inches (0.00 cm) from the back. If installed properly, the open fryer is designed for operation on non-

combustible oors only

Do not spray aerosols in the vicinity of this appliance while it is in operation.

2-4.

LEVELING THE

FRYER

2-5.

VENTILATION OF

FRYER

To prevent severe burns from splashing hot oil, position and install

fryer to prevent tipping or movement. Restraining ties may be used for

stabilization.

For proper operation, the open fryer should be level from side-to-side and

front to back. Using a level placed on the at areas around the vat collar,

on the middle well, and then adjust the casters until the unit is level.

The fryer should be located with provision for venting into an adequate exhaust hood or ventilation system. This is essential to permit efcient

removal of the steam exhaust and frying odors. Special precaution must be taken in designing an exhaust canopy to avoid interference with the operation of the fryer. We recommend you consult a local ventilation or

heating company to help in designing an adequate system.

Ventilation must conform to local, state, and national codes. Consult your local fire department or building authorities.

5March 2014

2-6.

GAS SUPPLY

When installing the gas open fryer, do not attach an extension

to the gas ue exhaust stack. This may impair proper

operation of the burner, causing malfunctions and possible

negative back draft.

The gas open fryer is factory available for either natural or propane gas. Check the data plate inside the left front door of the cabinet to determine

the proper gas supply requirements. The minimum supply for natural

gas is 7 inches water column (1.7 kPa) (17.0 mbar), and 10 inches water column (2.49 kPa) (24.9 mbar) for propane.

Do not attempt to use any gas other than that specied on the

data plate. Incorrect gas supply could cause a re or explosion

resulting in severe injuries and/or property damage.

Please refer below for the recommended hookup of the fryer to main gas line supply.

To avoid possible serious personal injury:

• Installation must conform with local, state,

and national codes, the American National Standard Z223.1/NFPA 54 -(the latest edition) National Fuel Gas Code, and the local municipal building codes. In Canada, the Natural Gas and Propane Installation Code is CSA B149.1 & Installation Codes - Gas Burning Appliances and local codes. In Australia, in accordance with Australian Gas Authority rules AS5601.1/2-2010.

• The fryer and its manual shutoff valve must

disconnected from the gas supply piping

system during any pressure testing of that system at test pressures in excess of 1/2 PSIG (3.45 kPa) (34.5 mbar).

• The fryer must be isolated from the gas

supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 PSIG (3.45 kPa) (34.5mbar).

• A standard one inch (2.54 cm), black steel

pipe and

malleable ttings should be used for gas

service connections for 3 & 4 well open fryers, and 3/4 inch (1.91 cm) for 2 wells.

• Do not use cast iron ttings.

• Although one inch (2.54 cm) size pipe is rec-

ommended for 3 & 4 wells and 3/4 inch (1.91 cm) for 2 wells, piping should be of adequate size and installed to provide a supply of gas

sufcient to meet the maximum demand

without undue loss of pressure between the meter and the open fryer. The pressure loss in the piping system should not exceed 0.3 in. water column (0.747 mbar).

6March 2014

2-6.

GAS SUPPLY

(CONT.)

Provisions should be made for moving the open fryer for cleaning and servicing. This may be accomplished by:

1. Installing a manual gas shutoff valve and a disconnect or union.

2. Installing a heavy-duty design CSA certied connector. In order to

be able to service this appliance, which is provided with casters, a connector complying with ANSI Z21.69-CAN 6.16 or CAN

1-6.10m88 and a quick-disconnect device, complying with ANSI

Z21.41or CAN 1-6.9m70, must be installed. It must also be installed with restraining means to guard against transmission of strain to the

connector as specied in the appliance manufacturer’s instructions.

3. See the illustration on the following page for the proper connection

of exible gas line and cable restraint.

The cable restraint limits the distance the open fryer can be pulled from

the wall. For cleaning and servicing the unit, the cable must be unsnapped

from the open fryer and the exible gas line disconnected. This allows better

access to all sides of the open fryer. The gas line and cable restraint must be

reconnected once the cleaning or servicing is complete.

7March 2014

2-6.

GAS SUPPLY

(CONT.)

For Australia or New Zealand:

Where a model is supplied with castors and is to be connected to a

xed gas supply via a exible hose connection, a restraining chain or wire of adequate strength shall be xed to the appliance and be suit able to be xed to the wall within 50

mm of each connection point. The

length of the chain or wire shall not exceed 80% of the length of the hose assembly.

8March 2014

2-7.

GAS LEAK TEST

2-8.

GAS PRESSURE

REGULATOR

SETTING

Prior to turning the gas supply on, be sure the gas valve knob on the gas

control valve is in the off position.

Upon initial installation, and after moving the unit, the piping and ttings

should be checked for gas leaks. A simple checking method is to turn on the gas and brush all connections with a soap solution. If bubbles occur, it indicates escaping gas. In this event, the piping connection must be redone.

To avoid re or explosion, never use a lighted match or open ame to

test for gas leaks. Ignited gas could result in severe personal injury and/

or property damage.

The gas pressure regulator on the gas control valve is factory set as follows:

• Natural: 3.5 inches water column (0.87 kPa) (8.72 mbar).

• Propane 10.0 inches water column (2.49 kPa) (24.9 mbar).

2-9.

ELECTRICAL

REQUIREMENTS

The gas pressure regulator has been set by Henny Penny and is not to be

adjusted by the user.

•

120 V, 50/60 Hz, 1 PH, 12 A

• 230 V, 50 Hz, 1 PH, 7 A

The 120 volt gas fryer is factory equipped with a grounded (earthed)

cord and plug for your protection against shock, and should be plugged into a three-prong grounded (earthed) receptacle. Do not cut or remove grounding (earthing) prong. Any 230 volt plug used on the 230 volt unit must conform to all local, state, and national codes.

To avoid electrical shock, this appliance must be equipped with an

external circuit breaker which incorporates a 3mm disconnection in all

ungrounded (unearthed) conductors. The main power switch on this

appliance does not disconnect all line conductors.

9March 2014

2-9.

ELECTRICAL

REQUIREMENTS

(CONT.)

To avoid electrical shock, do not disconnect the ground (earth) plug. This fryer must be adequately and safely

grounded (earthed). Refer to local electrical codes for

correct grounding (earthing) procedures or in absence

of local codes, with The National Electrical Code, ANSI/

NFPA No. 70-(the current edition). In Canada, all electrical

connections are to be made in accordance with CSA C22.2,

Canadian Electrical Code Part 1, and/or local codes.

Disconnect power supply before a thorough cleaning or servicing the fryer.

2-10.

MOTOR BEARINGS

2-11.

LIGHTING AND

SHUTDOWN OF THE

BURNERS

The electric motor bearings are permanently lubricated. DO NOT

LUBRICATE.

Turn the power switch to the OFF position.

2. Wait at least 5 minutes and then turn power switch to the ON position.

3. Press button on the controls (left or right).

4. The burner lights and operates in a Melt Cycle until the

shortening reaches a preset temperature.

5. Once the display shows a product selection or a double

dashes, press the desired product button.

The fryer is equipped with a ignition spark module which has a

set ignition safety time (TSA) of 90 seconds.

2-12.

TESTING THE

FRYER

To shutdown burner:

1. Press button on the controls (left or right).

2. Turn the power switch to the OFF position. NOTE: This turns off all vats.

Each Henny Penny open fryer was completely checked and tested prior to shipment. However, it is good practice to check the unit for proper operation.

10March 2014

2-13.

DIMENSIONS

1-WELL

Back

Side dimensions are the same for all units

Front

11March 2014

2-13.

DIMENSIONS

(CONT.)

2-WELL

Back

Side dimensions are the same for all units

Front

12March 2014

2-13.

DIMENSIONS

(CONT.)

3-WELL

Back Side

Side dimensions are the same for all units

13March 2014

2-13.

DIMENSIONS

(CONT.)

4 WELL

Back

14March 2014

SECTION 3: OPERATION

3-1.

OPERATING

COMPONENTS

Figure 3-1

Refer to explanations on the next pages.

2 5 6 73

10 8

11 12

Figure 3-2

Figure 3-3

Figure 3-4

15March 2014

3-1.

OPERATING

COMPONENTS

(CONT.)

Fig.

Item

No.

3-1 1

3-1 2

3-1 3

3-1 4

3-1 5

Description Function

This LED lights when the control calls for heat for the left/ right vat, and the

burners ignite and heat the oil

During normal operation, press this button to start and stop cook cycles for the

left basket; press to change displayed product; also used for √ to indicate YES or to conrm

During normal operation, press this button to start and stop cook cycles for the left basket; press to change displayed product; also used for X to indicate NO or cancel

Shows the product codes; shows the timer countdown during cook cycles;

shows the prompts during the lter modes; shows the selections in the Program

Digital Display

Mode; shows the temperature of the oil by pressing ; shows error codes (also displays in several languages)

Press once to view actual oil temperature; press twice to view oil set-point temperature; and press three times to view recovery information for each vat

from 250

F-300oF (121oC-149oC). Used in Programming Modes; used as ◄

button to back-up to a previous parameter in Program and Filter Modes.

3-1 6

3-1 7

3-1 8

3-1 9

3-1 10

Used to access the Filter Menu; also used for ▲ or ▼ buttons; press once to view the number of cook cycles before next lter in Global Filter or the mode or percentage of lter allowance in Mixed Filter; press twice to view the time and date of the most recent lter on each vat; press three times to view the number of hours of use of the lter pad presently in the drain pan.

Used to access the Program Modes; used as ► button to advance to the next

parameters in Program and Filter Modes; press to select 2nd languages and volumes

Press to turn on and off the heat system for the left vat(s); on full vats either button can be used

Each product button LED lights when that particular product has been selected, or when it is compatible with cook temperature.

Press to select the desired product; press to place the letters under the button, during naming a product in Program Mode

The can be used to start an Idle Mode if enabled in Special Program Mode

16March 2014

3-1.

OPERATING

COMPONENTS

(CONT.)

Fig.

Item

No.

3-2 11

3-3 12

3-4 13

Description Function

A Filter Beacon® is found beside each black drain knob; when lit blue, indicates the oil should be ltered at this time; beacon ashes when the drain needs

opened or closed

When the power switch is turned to the ON position, power is supplied to the controls and pumps

For fryers with a bulk oil supply, press this button to ll the BIB

17March 2014

3-1.

OPERATING

COMPONENTS

(CONT.)

Item

No.

1 Filter Drain Pan Assy. Oil is drained into this pan and then is pumped through lters to help

2 Drain Valve Knob

3 Basket Rest The baskets hang on this when not in use, or to drain the product after a

4 Vat Covers Covers the vat when not in use

5 BIB Support Area that holds the Jug-in-a-Box; holds oil to be pumped into vats to top-

Description Function

prolong the use of the oil

Pull-out on black knobs to open drain valve and oil drains from vat; Push-

(Optional)

in to close drain valve and oil can be pumped into vat

cook cycle

off the oil level by the Oil Guardian™ process

1 5

18March 2015

3-2.

SET-UP MODE

Upon initial start-up, the controls will ask to conrm the settings for

the fryer.

When main power switch is turned on, “OFF” shows in both displays. Press on either side and *SETUP* *ENTER CODE* shows in display. Press 1, 2, 3, and “LANGUAGE” shows on the left display, “ENGLISH” on the right display.

Use ▲ or ▼ buttons to change the operation display to: Greek “EΛΛHNIKA”, Russian “РУССКИИ”, Swedish “SVENSKA”, German “DEUTSCHE”, Portuguese “PORTUG.”, Spanish “ESPANOL”, or French “FRANCAIS”.

Press ► to continue with the other set-up items which include:

• TEMP FORMAT -

• TIME FORMAT - 12-HR or 24-HR

• ENTER TIME - Time of day (use product buttons to change)

• ENTER TIME - AM or PM

• DATE FORMAT - MM-DD-YY or DD-MM-YY

• ENTER DATE - Today’s date (use product buttons to change)

• DAYLIGHT SAVING TIME - 1.OFF; 2.US (2007 & after);

F or oC

3.EURO; 4.FSA (US before 2007)

• FRYER TYPE - ELEC or GAS

• VAT TYPE - FULL OR SPLIT

• AUTOLIFT ENABLED? - NO LIFT or YES LIFT

• BULK OIL SUPPLY - YES or NO

• BULK OIL DISPOSE? - YES or NO

• S/N - Shows serial number of the unit or can be recorded (THIS

SERIAL NUMBER SHOULD MATCH THE SERIAL

• NUMBER ON THE DATA PLATE, ON THE DOORS.)

• 2nd LANGUAGE - By setting a second language in the controls,

2 languages can now be easily chosen by pressing during normal operation. One language shows in left display and

second language shows in right display. Pressing the √ button

under desired language, selects that language seen in displays.

• 2nd VOLUME - By setting a second volume in the controls,

2 volumes can now be easily chosen by pressing twice during normal operation. One volume setting shows in left display (NONE to 10; 10 being the loudest) and a second

volume shows in right display. To select volume, press √ button

under desired volume.

• SETUP COMPLETE - OFF is displayed and unit shuts down.

Unless otherwise indicated, use ▲ or ▼ to change settings.

Setup Mode can also be accessed by re-initializing the controls, in Special

Program Mode, in Level 2 programming (SP-3).

19March 2014

+ 58 hidden pages