Heitronic 30590, 30591 User guide
GB Installation and operating instructions
Heitronic
®
LED recessed luminaire/floor-mounted luminaire
Art. No. 30590,30591
Many thanks for deciding to buy our lights.
Our LED light is made out of sturdy, high value materials and will provide you with quality lighting. The
LED light is suitable for installation on a normal flame-proofed upper surface. It is suitable for indoor
and outdoor installation, e.g. as garden or lawn decoration. Capacitance 5 kN.
Please read through installation and operation instructions carefully and keep these in a safe
place for future reference.
We do not accept liability for damage to persons or property caused by non observation of the
instructions, improper handling or for unauthorized changes made to the product.
Contents of packaging:
1 recessed luminaire with wiring cables
Installation and operating instructions
Technical data:
Article Connection Type Illuminant
30590 12V AC
30591 12V AC
round Ø 28 mm
Warmwhite
square 32 x 32 mm
warmwhite
1 LED-illuminant 0,3W
cannot be changed
1 LED-illuminant 0,3W
cannot be changed
LEDClass
1 III, IP 68 (0,5m)
1 III, IP 68 (0,5m)
Protection
Class
Safety and warning notes:
Do not look directly into the LED - especially for longer periods of time - without protecting
your eyes. A LED beam should not be directed into other people's eyes.
Make sure, before using the light that it has not been damaged during transportation. Do not
operate the light if the cable or the electrical parts are damaged.
Never attempt to repair any defective parts yourself. All repairs must be performed by trained
professionals only.
Keep packaging materials well away from children and pets. Danger of suffocation!
Be careful. The packaging contains small parts which can be swallowed by children.
The entire product must neither be changed nor converted. Changes made to the light lead to
annulment of the guarantee (warranty).
Care and servicing:
You must make sure that the power supply is disconnected before cleaning.
Use a dry, or slightly damp cloth for cleaning.
Never use chemicals, inflammable cleaners or abrasives for cleaning. These can damage the
surface and / or the insulations of the light.
Disposal:
Old electronic equipment must be brought to public connection points and must not be
disposed of as household waste.
H. Vollmer GmbH
Allmendring 29
D-75203 Königsbach-Stein
Installation instruction Art. No. 30590,30591 Page 1 of 2 Status 07.2013
Installation:
Heitronic
®
Make sure that the connection values of your building installation for the power supply to the
light comply with the data stated on the name plate of this light.
The light is suitable for installation into normal inflammable surfaces. The light must not be
covered under any circumstances whatsoever with thermally insulating coverings or similar
materials.
Unpack the individual parts and check that they are complete.
Position the LED-driver in the designated area. The installation area must be well ventilated
due to the heat produced by the LED-driver. Comply with the ambient temperature and the
housing temperature of the LED-driver (see nameplate). During use, LED-driver can create a
slight humming noise. Ensure that you do not install LED-drivers in locations which act as
resonators and thereby lead to increased noise.
Make sure that the base and the fastening material are suitable and the weight of the lights
can be supported permanently and reliably.
Do not bend the cable, make sure that the cable and the plug are free from strain and
rotational forces. Protect all cables and insulations from possible damage.
To position the surface-mounted lights, drill holes of 23 mm diameter
Make sure you have a stable and reliable fastening.
Connect the luminaire to the LED-driver.
After installation, connect the LED-driver to the mains supply.
The name plate must not be removed.
H. Vollmer GmbH
Allmendring 29
D-75203 Königsbach-Stein
Installation instruction Art. No. 30590,30591 Page 2 of 2 Status 07.2013
Loading...