Heatmaster enviro 17 Quick Step Installation Manual

Download

Page 1

Quick Step Installation Manual

www.heatmaster.com.au

enviro

Do...

enviro 17

Page 2

Quick Step Installation Manual

enviro

Back view in mm

453

180

153

331

109

Standard

Extended

Extended Facsia

550mm required depth

690mm

required

height

960mm

required opening width

set the Enviro firebo x to your desired heigh t

ELEVAT ION VIEW

PLAN VIEW

Front

wall

Firebox dimensions

With it’s revolutionary design, the Enviro can be mounted at any height on the wall. You can choose to install the Enviro at ground level with standard fascia or further up the wall with extended fascia.

Gas imput

High 42 MJ/h Low 32 MJ/h

Minimum framing dimensions

Keep vertical

Move fascia forward

Note: Clip in manual control on bottom left side of fascia

fascia clips slip down over heat box lip

1 – Electrical power

cable (Requires isolation switch)

2 – Incoming gas

connection (1/2” BSP Male connector)

3 – Extraction fan 4 – Incoming air

B – Your choice of pebbles, coals or logs placed into the

* C and D are only applicable if installing under bench top and or into Joinery.

C – Minimum enclosure height from top of box = 300mm D – 1 Inlet and 1 outlet ventilation with a cross sectional

area of 5000mm for each.

For inbuilt installation (into a wall)

Optional freestanding casing

• Casing H 733 x D 580 x W1080mm

• 200mm dia cut out in top of casing to allow for decorative rigid flue (to hide flexi exhaust and air intake)

• Air holes in the back top of casing for air ventilation

• Provisional holes for both gas line and power cord in rear of casing

When using the freestanding casing, simply centre unit within the casing and attach fascia (as outlined)

Rear View

Access panel advised for servicing if required

Page 3

Quick Step Installation Manual

enviro

Attaching the fascia

While attaching the facsia is straight forward, it is important that it remains vertical all the time to make sure the top and bottom clip in by way of clips at both the top and bottom. (Before fascia can be removed, door must be unscrewed and removed)

Resting on the heath

If mounting the Enviro

recommended that a non combustible hearth be used for a minimum

Further up the wall

Extended facsia

Standard facsia

Remove all four screws

Keep vertical

Move fascia forward

Note: Clip in manual control on bottom left side of fascia

fascia clips slip down over heat box lip

fascia clips slip down over heat box li

on the bottom lip also.

fascia clips slip down over heat box lip

STEP

For inbuilt installation (into a wall)

Optional freestanding casing

• Casing H 733 x D 580 x W1080mm

• 200mm dia cut out in top of casing to allow for decorative rigid flue (to hide flexi exhaust and air intake)

• Air holes in the back top of casing for air ventilation

• Provisional holes for both gas line and power cord in rear of casing

When using the freestanding casing, simply centre unit within the casing and attach fascia (as outlined)

1080

733

550

440

200

440

150

180

Rear View

Page 4

Quick Step Installation Manual

enviro

Quick Step Installation Manual

enviro

Openable

Window

Door

Flue Terminal Indicates areas for flue terminals

Use 3 bends only

Our flexible flue has the ability to bend 3 times between the heating unit and the cowl. This includes the bend straight out of the heater if you’re fluing through the ceiling or floor.

Make the flue pipe go over the bearers and joists.

You may bend the flue over joists and bearers. It is recommended that a 20mm clearance be maintained between the smaller gas exhaust flue and combustible materials.

Fluing where the pipe had a spot lower than the rest.

Never allow a low spot in the flue. Installing the flue with a dip or “goose neck” can result in reduced efficiency or even prevent the fire from working.

Do...

Never Do...

Using your exible ue pipe

The Enviro’s revolutionary ue system incorporates one 65mm diameter pipe and one 58mm diameter pipe.

Congure triangle

Addition literature

Supplements for ue installation and heat transfer can be obtained by contacting your Heatmaster dealer.

Key Information – Quick step check list

*All information contained in this mini summary is correct at the time of publication. This is only a summary and should be read in conjunction with the full installation

instructions. Pictures are representative only and are not drawn to scale. Installation should be carried out by a licensed gas tter and any electrical work carried out by a

licensed electrician.

Minimum clearances required for balanced ue terminals or the ue terminals of outdoor appliances

(according to AS5601-2004[AGA gas installation code] or NZS 5261 [New Zealand]

a Bellow eaves, balconies or other projections 300 mm

b From the ground or above a balcony 300 mm

c From a return wall or external corner 500 mm

d From a gas meter (M) 1000 mm

e From an electricaity meter or fuse box (P) 500 mm

f From a drain or soil pipe 150 mm

g Horizontal from an building structure 500 mm

From any other ue terminal, cowl or combustion air intake

500 mm

j Horizontally from an openable window, door, or non-mechanical

air inlet, or any other opening into a building, with the exception of

sub-oor ventilations 500 mm

k Vertically below an openable widow, door,or non-mechanical

air inlet, or any other opening into a building, with the exception of

sub-oor ventilation 150 mm

l Minimum horizontal clearance to any surface

(such as an exterior wall) for vertical terminations 610 mm

m Minimum height above roof line for vertical termination 600 mm

✘

✔

Example 1

Example 2

Example 3

A 20mm clearance is recommended from the extraction (smaller) ue to combustibles.

Plumber Incoming gas connection provided – 1/2 inch BSP male connector Page 2

Gas input – 42MJ high

32MJ low

Page 2

Manifold pressure High (Nat gas) 0.69 Kpa Low (Nat gas) 0.45 Kpa High (LPG) 2.25 KPA Low (LPG) 1.38 KPA

Manifold pressure is factory set. To check pressure and adjust refer to page 8 of the customer operation information & Installation

instructions.

Electrician Standard ex 2m, 3 pin plug provided. Requires power point with

double pole isolation switch.

Page 2

Using up to three bends, use this triangle to

work out measurements for your 4.5 mtr

ue. Remember, the rst bend out of the

Heater is counted as one. The Enviro

can be ued through the roof, wall

or oor. *See your Heatmaster

dealer for full details.

Appliance must be tested for correct operation prior to leaving - minimum 20 minutes. If appilance cannot be adjusted to preform correctly contact Heatmaster prior to leaving.