Page 1
E112697
UL 60601-1
CSA C22.2 No. 601.1-M90
Model 2595KL
Digital Chair Scale
User Instructions
P/N UM2595KL_REV20200128
PELSTAR, LLC 9500 West 55th St. McCook, IL 60525-7110 USA www.homscales.com
Health o meter® Professional 2595KL
© Pelstar, LLC 2020
Page 2
Health o meter
Thank you for your purchase of this Health o meter® Professional product. Please read this
manual carefully, and keep it for easy reference or training.
®
Professional 2595KL
TABLE OF CONTENTS
Caution and Warning................................................................................................. 3
Specifications for This Scale ..................................................................................... 4
Certifications / Connectivity / Disposal / Service ........................................................ 5
Assembly Instructions 2595KL Scale ....................................................................... 6
Set Up Information / Batteries ................................................................................... 9
Operating Instructions ............................................................................................... 11
Maintenance .............................................................................................................. 12
Troubleshooting ........................................................................................................ 13
Calibration Procedure ................................................................................................ 14
Warranty .................................................................................................................... 15
Note: This scale has been factory calibrated, and does not
require calibration prior to use.
Please register your scale for warranty coverage at:
www.homscales.com
For User Instructions updates and revisions please go to:
P/N UM2595KL_REV20200128
www.homscales.com
2
Page 3
CAUTION AND WARNING
Intended Use
The Health o meter® Professional 2595KL scales were intended to be used in a professional medical
environment by trained medical staff. This product was designed to weigh patients that are sitting on
the chair. Do not modify the product or use it for anything other than its intended purpose.
To prevent injury and damage to your scale, please follow these instructions very carefully.
Assemble and operate the scale per the enclosed user instructions.
For accurate weighing, this scale must be placed on a flat, stable surface.
For accurate weighing, verify before each use the proper operation according to the procedure
described in this manual.
Do not transport the scale with a patient or object on the tray.
Do not exceed the weight capacity specified for the scale.
Do not use in the presence of flammable or explosive materials.
Ensure that the scale or AC adapter do not come in contact with liquids, excessive temperature, or
excessive humidity.
If the scale becomes damaged, it should not be operated until properly serviced.
Patient/caregiver safety
This scale is designed for static weighing of patients only. No scale should be used for patient
transfer. Pelstar, LLC assumes no responsibility for patient injury or scale damage should this
caution be ignored by the scale operator.
To prevent patient injury, the patient must be attended throughout the entire weighing event.
Ensure to lock or block casters while weighing a patient. Wheels must not roll freely when
positioning or seating a patient.
When operating the scale with batteries:
If “LOBAT” appears on the display, replace the batteries or switch to the AC adapter as soon as
possible.
When replacing / inserting batteries, be sure to use all new batteries.
When operating the scale with the (optional) AC adapter:
Operate this scale exclusively with the AC adapter that is specified (ADPT30) (not included). Use of
an unspecified adapter will void the warranty, and can pose a serious safety hazard.
Prior to using this scale, inspect the AC adapter cord for cracking / fraying, or for broken / bent plug
prongs.
Prior to using this scale, ensure that the AC adapter is plugged into an outlet with the rated voltage
appropriate for operation.
Ensure that the AC adapter outlet is wired to a circuit breaker or other protected power source.
Unplug the AC adapter, and carefully store both the adapter and adapter cord before moving the
scale.
Operating this scale at voltages and frequencies other than specified can damage the equipment
and will void the warranty.
This equipment has been tested and found to comply with the EMC limits for the Medical Device Directive
93/42/EEC (EN 55011 Class A and EN 60601-1-2). These limits are designed to provide reasonable
protection against harmful interference in a typical medical installation. The equipment generates, uses
and may radiate radio frequency energy and, if not installed and used in accordance with these
instructions, may cause harmful interference to other devices in the vicinity. There is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference with
other devices, which can be determined by turning the equipment off and on, the user is encouraged to try
to eliminate the interference by one or more of the following measures:
Reorient or relocate the receiving device.
Increase the separation between the equipment.
Connect the equipment into an outlet on a circuit different from that to which the other device(s) is
connected.
Consult Customer Service or a field service technician for help.
In no event whatsoever shall Pelstar, LLC be liable for damages or injuries arising from or
connected with the assembly, use, or misuse of its products.
P/N UM2595KL_REV20200128
3
Page 4
SPECIFICATIONS FOR THIS SCALE
Capacity and
Resolution
600 lb x 0.2 lb (270 kg x 0.1 kg)
Power Requirements
Adapter Model No. UE15WCP1-090050SPA, Part No.
UE141023HKKK1-P
Health o meter® Professional Model (ADPT30) (included)
Input: 100-240V – 50/60Hz, 500mA
Output: 9.0V - - - 0.5A
or 6 C-cell batteries (not included)
Environmental
Operating temperatures: 10°C to 35°C (50°F to 95°F)
Storage temperatures: 0°C to 50°C (32°F to 122°)
Atmospheric Pressure: 50hPa-1060hPa
Humidity: 10%-85% RH
Physical Dimensions
Seat
Depth: 15-3/4” (400mm)
Width: 18-1/4” (464mm)
Arms
Span: 19-3/4” (502mm)
Entire Scale
Length: 36-1/2 (927mm)
Width: 23-1/2” (597mm)
Height: 40” (1016mm)
Weight: 80lb, 4oz (36.5kg)
Attention, Consult Accompanying Documents
Type BF Applied Parts
AC to DC power supply
GENERAL
The Health o meter® Professional 2595KL Digital Chair Scale uses highly sophisticated
microprocessor technology. This precision instrument is designed to provide accurate,
reliable and repeatable weight measurements by providing features that make the weighing
process simple, fast and convenient. Weight is displayed in kilograms or pounds. The scale
includes a seat with arm supports, and a footstool that can be folded up for easy entry/exit.
Also included in the scale are two large casters, caster brakes, and a handrail for easy
mobility. The unit can be operated using its AC adapter or with 6 C-cell batteries.
2595KL SCALE SPECIFICATIONS
DEFINITION OF SYMBOLS
P/N UM2595KL_REV20200128
4
Page 5
CERTIFICATIONS / CONNECTIVITY / DISPOSAL /
Pelstar, LLC has been officially certified as the manufacturer
of Health o meter® Professional medical devices. The Pelstar,
LLC quality assurance system covers the development,
production, sales and service of medical scales and
measuring systems.
This product is tested to and meets the requirements of:
1. UL60601-1 First Edition: Safety for Medical Electrical
Equipment
2. CSA C22.2 No. 601-1 M90: Medical Electrical Equipment
SERVICE
Certification Descriptions
Scale Disposal
This Health o meter® Professional scale must be disposed of properly as electronic waste.
Follow the national, regional or local regulations which apply to you for disposal of electronic
waste or batteries. Do not dispose of this device in the domestic waste stream.
Scale Connectivity Information
For reliable transmission of weight data, this scale is designed to connect to a computer,
monitor, or other electronic data device via various Health o meter® Professional Connectivity
Solutions. This connectivity helps minimize transcription errors when recording patient data. For
further information regarding how to connect this scale to other electronic devices, please
contact Health o meter® Professional Scales Technical Support at 800-638-3722 or visit
www.homscales.com/innovations/connectivity.
Customer Service Information
The 2595KL Digital Chair Scale is shipped assembled in one carton, except for final installation
of scale casters and brakes. Carefully inspect the carton for shipping damage before unpacking.
If damage is found, contact Customer Service.
For further information or telephone support, please contact Customer Service at:
Telephone: 1 (800) 815-6615
Email: HomProCS@homscales.com
P/N UM2595KL_REV20200128
5
Page 6
2595KL ASSEMBLY INSTRUCTIONS
5mm Allen Wrench
Leveling Feet
Caster Brake
To avoid damaging the 2595KL when unpacking it, do not use a box cutter, knife, scissors or
any sharp object when opening the protective inner packaging. If damage is found,
contact your shipper or a Health o meter® Professional representative immediately. Claims
must be filed with the shipper as soon as possible after receipt of the package. The following
information details what you will find inside the carton as you unpack the parts for assembly. Set
the carton aside for storage.
Parts List:
Carton
(1) Chair Scale Assembly
(2) Casters
(2) Caster Breaks
(2) Leveling Feet
(2) Bolts
(1) AC Adapter
(1) 3/16” or 5mm Allen Wrench
Figure 1
P/N UM2595KL_REV20200128
6
Page 7
2595KL ASSEMBLY INSTRUCTIONS
Assembly Instructions (Refer to Figures 1- 3)
Note: Do not attach the AC adapter at this point. Wait until Step 9.
Caution: It is recommended that the assembly be performed by two persons.
1. Remove the chair scale assembly from the carton and place chair scale on a flat, level
and dry surface.
2. Pull forward on the handrail to tip the scale over, and gently place it face down on the floor.
3. Thread the (2) leveling feet into the underside of the chair scale assembly. Each foot should
be completely hand tightened.
4. Position the casters and caster brakes on both sides of the chair assembly.
5. Position the caster and caster brake with each bolt hole. Place the bolt through each bolt
hole and tighten using the 3/16” (5mm) Allen wrench (see Figure 3).
Note: Ensure caster brake is positioned with one tab on the exterior of the caster.
6. Carefully tilt the scale back to an upright position on the floor.
Warning: Do not drop scale, as this can permanently damage the load cells.
7. Adjust the feet to level the scale.
8. Connect the AC adapter to the power port in the display assembly. Do not plug the scale
into a power source until the scale is fully assembled.
Note: The scale may be operated by an AC adapter (included), or by 6 C-cell batteries (not
included). Using the battery option, unplug the AC adapter from the adapter jack and ensure that
there are 6 C-cell batteries in the display assembly. The scale will automatically switch to battery
power when the AC adapter is absent or not plugged in.
9. The scale is now assembled. Plug the AC adapter into a power source and / or insert
batteries. (See page 9 for battery installation).
P/N UM2595KL_REV20200128
7
Page 8
2595KL ASSEMBLY INSTRUCTIONS
3/16” (5mm) Allen Wrench
Caster Brake
Figure 2. Assembly of the 2595KL
Figure 3
P/N UM2595KL_REV20200128
8
Page 9
SET UP INFORMATION / BATTERIES
------
------
Set Up Information (Refer to Figures 4- 5)
1. Place 6 C-cell batteries in the battery holder (see “Replacing Batteries” below), or plug the
AC adapter into the chair scale assembly and into the power source.
2. Press the ON/OFF button to turn the scale on. The display will show “START”, then “0.0”.
3. When the self-test function is complete:
The digital display reads “0.0”.
“LB” or “KG” is indicated on the right side of the display.
4. Place a weight not to exceed 600 lb (270 kg) on the scale. The digital display should blink
“
” until the weight calculation is complete.
5. Press the LBS/KG button to select the weight mode, either in kilograms or pounds.
6. Press the REWEIGH button; the digital display will read the weight on the chair scale
assembly. Pressing the REWEIGH button will reweigh the weight that is still on the chair
scale assembly.
7. Remove the weight from the chair scale assembly, the digital display will continue to show
the weight of the item that was on the scale.
8. Press the ZERO button; the digital display will return to “0.0”.
9. Press the ON/OFF button to turn the chair scale assembly off. The display will show “OFF”
and will then shut off.
Note: If the set up procedure failed, go to the troubleshooting instructions. If the problem is still
not corrected, refer to qualified service personnel.
Installing / Replacing Batteries
1. Loosen the two plastic knobs found underneath the display assembly until the battery
holder is released from the chair scale assembly and rests on the plastic knobs.
2. Carefully pull out the cable to provide access to the battery holder.
3. Raise the battery holder and simultaneously rotate it counterclockwise 1/4 turn. Carefully
remove the holder from the chair scale assembly.
4. Install/replace the batteries with 6 new C-cell batteries.
5. Place the battery holder onto the plastic knobs by rotating it 1/4 turn clockwise.
6. Hold the battery holder close to the chair scale assembly and tighten the two plastic knobs
to secure in place. Be careful not to damage the cable.
KG Lockout
The default weighing mode for this scale can be changed from LB/KG to KG only. To change to
KG, turn the scale on and wait for the display to show “0.0”, then press and hold the LBS/KG
button for 20 seconds until the scale beeps 6 times. The scale is now locked in the KG mode
and the user cannot toggle between LB and KG. To disable the KG Lockout feature, press and
hold the LBS/KG button for another 20 seconds until the scale beeps 6 times, indicating that the
user can again toggle between pounds and kilograms.
P/N UM2595KL_REV20200128
9
Page 10
SET UP INFORMATION / BATTERIES
Figure 4. Replacing Batteries
Figure 5
P/N UM2595KL_REV20200128
10
Page 11
OPERATING INSTRUCTIONS
ITEM
DESCRIPTION
FUNCTION
1
ON/OFF button
Turns scale ON and OFF.
2
REWEIGH button
Allows repeated reweighing of person.
3
ZERO button
Zeros digital display prior to weighing. Enables the
cancellation (tare) of weight if some object was placed on the
scale.
4
LBS/KG button
Selects kilograms or pounds.
5
BAT indicator
When ON, indicates scale batteries are low. The batteries
should be replaced.
6
ZERO indicator
When ON, indicates the scale is stable and ready for use.
7
Digital Display 6 Digit LCD
Displays weight in kilograms or pounds as shown by the “LB”
or “KG” indicator on the right side of the display. When
REWEIGH button is depressed, display will blink “
------
------
”
until
patient’s weight is determined.
8
LB indicator
When ON, indicates displaying weight in pounds.
9
KG indicator
When ON, indicates displaying weight in kilograms.
Figure 6. Control Panel
P/N UM2595KL_REV20200128
11
Page 12
OPERATING INSTRUCTIONS
------
------
MAINTENANCE
1. Press the ON/OFF button to turn the scale on.
2. Wait until “0.0” appears on the digital display.
3. Position the patient onto the scale. The display will blink “
determined.
4. To reweigh the patient without asking the patient to stand up and sit on the scale again, press
the REWEIGH button.
5. Assist the patient off of the scale. The digital display should continue to read the person’s
weight until REWEIGH or ZERO button is pressed.
Note: When batteries are being used and the scale has been inactive for 2 minutes, the scale will
turn itself off to conserve power. To restart the scale, press the ON/OFF button.
GENERAL
This section provides instructions for maintenance, cleaning, and troubleshooting for the
2595KL Digital Chair Scale. Maintenance operations other than those described in this section
should be performed by qualified service personnel.
MAINTENANCE
until the weight of the person is
”
Before first use and after periods of non-use, check the scale for proper operation and function.
If the scale does not operate correctly, refer to qualified service personnel.
1. Check overall appearance of the scale for any obvious damage, wear and tear.
2. Inspect the AC adapter for cord cracking or fraying, or for broken or bent prongs.
Cleaning and Disinfecting
Proper care and cleaning is essential to ensure a long life of accurate and effective weighing.
1. Health o meter® Professional recommends using one of the following solutions on a soft
cloth or disposable wipe:
● mild soap and water solution
● 70% isopropyl alcohol
● solution with 1-5% hydrogen peroxide concentration
After cleaning/disinfecting, wipe with a cloth dampened with water and then with a clean dry
cloth. To avoid residue build-up or damp surfaces, ensure all scale parts are completely dry
after cleaning.
2. Never use rough or abrasive materials to clean the scale, as these will damage the scale’s
finish.
3. Do not submerge the scale in water or any other liquid.
4. Do not pour or spray fluids directly on the scale.
P/N UM2595KL_REV20200128
12
Page 13
TROUBLESHOOTING
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
Scale does not turn on
1. Defective battery
2. Faulty electrical outlet
3. Defective power supply
1. Replace batteries
2. Use a different outlet
3. Replace AC adapter
Questionable weight or
the scale does not zero
1. External object interfering
with the scale
1. Remove interfering object
from the scale
2. The display did not show
“0.0” before weighing
2. Remove the patient from
the scale. Zero the scale
and begin weighing
process again
3. Scale is not placed on a
level floor
3. Place the scale on a level
floor and begin weighing
process again
4. Scale is out of calibration
4. Check weight with known
weight value
The display shows “OL”
The load on the scale exceeds
the capacity
Remove the excess weight
and use the scale according to
its limits
The display shows “UL”
The scale is in under-load
condition
Make sure all seat parts and
handles are installed in place
and fixed properly
The display shows “LO BAT”
The battery is depleted
Replace batteries according to
instructions
Refer to the following instructions to check and correct any failure before contacting
service personnel.
P/N UM2595KL_REV20200128
13
Page 14
CALIBRATION PROCEDURE
ACTION
DISPLAY SHOWS
Press and hold the REWEIGH and ZERO buttons at the
same time, while pressing the ON/OFF button to turn on
the scale. “LOAD” will briefly appear on the display,
followed by “200.0 LB” indicates you can calibrate.
Release all three buttons.
“LOAD” followed by
“200.0 LB”
Ensure there is no weight on the scale and press the
REWEIGH button. “Clear” will flash on the display,
followed by “--------”. At this time the scale is calculating
zero calibration. After zero calibration, the display will
flash “PUT” followed by “200.0 LB”.
“Clear” followed by
“-------”. Then “PUT”
followed by “200.0 LB”
Place 200 lb on the scale. Then press REWEIGH. “CAL”
will appear on the display, followed by “FAC” followed by
5 digits. The calibration factor should be in the range
between 8000 and 10000. If the number is out of that
range, contact Customer Service at 1-800-815-6615.
“CAL” followed by
“FAC” followed by
“XXXXX”.
If the calibration factor is within range, press the
REWEIGH button. “DONE” will appear on the display,
followed by “START”, followed by “0.0”. Remove the
weight from the scale.
“DONE” followed by
“START”, followed by
“0.0”.
Calibration procedure is complete.
This scale has been factory calibrated, and does not require calibration prior to
use. If required, the scale can be calibrated. The following calibration assumes the
scale is set to pounds, and 200 lb is employed as the calibration standard.
Note: Only weights certified and traceable to national standards are to be used for
calibration procedures.
Scale Calibration
P/N UM2595KL_REV20200128
14
Page 15
WARRANTY
Limited Warranty
What does the Warranty Cover?
This Health o meter® Professional scale is warranted from date of purchase against defects of materials or in
workmanship for a period of two (2) years. If product fails to function properly, return the product, freight prepaid and
properly packed to Pelstar, LLC (see “To Get Warranty Service”, below, for instructions). If the manufacturer
determines that a defect of material or in workmanship exists, the customer’s sole remedy will be replacement of the
scale at no charge. Replacement will be made with a new or remanufactured product or component. If the product is
no longer available, replacement may be made with a similar product of equal or greater value. All replaced parts are
covered only for the original warranty period.
Who is Covered?
The original purchaser of the product must have proof of purchase to receive warranty service. Please save your
invoice or receipt. Pelstar dealers or retail stores selling Pelstar products do not have the right to alter, or modify or in
any way change the terms and conditions of this warranty.
What is Excluded?
Your warranty does not cover normal wear of parts or damage resulting from any of the following: negligent
use or misuse of the product, use on improper voltage or current, use contrary to the operating instructions, abuse
including tampering, damage in transit, or unauthorized repair or alternations. Further, the warranty does not cover
natural disasters, such as fire, flood, hurricanes and tornadoes. This warranty gives you specific legal rights, and you
may also have other rights that vary from country to country, state to state, province to province or jurisdiction to
jurisdiction.
To get Warranty Service make sure you keep your sales receipt or document showing proof of purchase. Call
(+1) 800-638-3722 or (+1) 708-377-0600 to receive a return authorization (RA) number, which must be included on
the return label. Attach your proof of purchase to your defective product along with your name, address, daytime
telephone number and description of the problem. Carefully package the product and send with shipping and
insurance prepaid to:
Pelstar, LLC
Attention R/A#_____________
Return Department
9500 W. 55th St.
McCook, IL 60525
Extended Warranty Available*
This scale is eligible for Health o meter® Professional ScaleSurance® Extended Warranty Program. ScaleSurance®
extends the warranty period for an additional two years. This extension to the standard Limited Warranty can be
purchased with new scales or for a facility’s existing scale before its current warranty has expired. To learn more, visit
www.homscales.com/scalesurance/ or contact your medical supply distributor.
*Not available in all countries
PELSTAR, LLC
9500 West 55th St. McCook, IL 60525-7110 USA
1-800-638-3722 or 1-708-377-0600
PLEASE REGISTER YOUR SCALE FOR WARRANTY COVERAGE AT:
www.homscales.com
Health o meter® is a registered trademark of Sunbeam Products, Inc. used under license.
Health o meter® Professional products are manufactured, designed, and owned by Pelstar, LLC.
We reserve the right to improve, enhance, or modify Health o meter® Professional product features or specifications
without notice.
© Pelstar, LLC 2020
P/N UM2595KL_REV20200128
15
Loading...