Page 1
Refrigerated Slim
Drop-In Wells
Models: CWB-S1, -S2, -S3, -S4
Project
Item #
Quantity
Hatco's Refrigerated Slim Drop-In Well is a full-size
unit that blankets your pre-chilled food product to
retain optimum freshness and taste in one efcient
and easy operation – but placed lengthwise. This
provides customers with a complete cold well
within easy reach, regardless of the sneeze guards.
Standard features
• Insulated wells available in 1 to 4 full-size pan
congurations, but placed lengthwise
• NSF 7 approved cold wall construction utilizes R-404A
refrigerant keeping food product cold without drying
it out
• Adjustable condensing unit can rotate 180 on all models
for easy venting adjustments and exibility at installation
• Mobile condensing unit can be moved in 5" (123 mm)
increments from center to left (away from drain) on the
two-, three- and four-pan units (CWB-S1 is rotatable only)
• Easy serviceability with a sight glass, service valves,
dryer/lter and a receiver. Long, exible refrigerant line
(ability to pullout condensing unit) for service
• Auto-defrost is activated through an advanced electronic
controller programmed at customer location
• Optimal insulation on sides and bottom ensure better
cold retention
• Environmentally friendly insulation used throughout
• 1" NPT drain simplies cleaning
Model CWB-S4 with optional slant
kit, accessory (hotel) food pans
additional support bars
Model CWB-S2
with accessory (hotel)
food pans and additional support bars
Options (available at time of purchase only)
c
Additional Four-Year Parts Only Warranty on the Compressor at Time of
Unit Purchase
c
Slant Kit to give Cold Wells a 5 tilt
Accessories
Pan Support Bars
c
12" (305 mm)
Stainless Steel Food Pans:
c
Third-Size (2.5" [64 mm] H)
c
Full-Size (2.5" [64 mm] H)
c
Full-Size (6" [152 mm] H)
c
False Bottom (perforated false bottom)
Wire Trivets Stainless:
c
Half-Size (10.19" [259 mm] W x 7.625 [194 mm] D)
c
Full-Size (10.125" [259 mm] W x 18" [457 mm] D)
c
Half-Size (2.5" [64 mm] H)
c
Full-Size (4" [102 mm] H)
Unique angled inside wall design
provides easy access and clear
views, while allowing cold air
to effectively blanket your food
product
HATCO CORPORATION
(800) 558-0607
Form No. CWB-S Spec Sheet Page 1 of 3 May 2016
(414) 671- 6 350
l
l
www.hatcocorp.com
l
P.O. Box 340500 Milwaukee, WI 53234-0500 U.S.A.
l
equipsales@hatcocorp.com
intlsales@hatcocorp.com
l
Page 2
Refrigerated Slim Drop-In Wells
CWB-S4: 90.25" (2292 mm)
CWB-S3: 69.19" (1757 mm)
CWB-S2: 48.125" (1222 mm)
CWB-S1: 27.06" (687 mm)
12.03"
(306 mm)
Drain
plumbing to be
installed per local codes.
Air Flow
Air Flow
5˚ slant
1.14"
(29 mm)
3.5"
(89 mm)
6.48" (165 mm) for CWB-S2, S3, S4
4" (102 mm) for CWB-S1
Models: CWB-S1, -S2, -S3, -S4
Ordering Instructions:
Please specify the following with
each order:
1. Desired Voltage:
120 for CWB-S1, -S2, -S3, -S4
2. Number of Drop-In
Wells Required:
1-, 2-, 3- or 4-pan
NOTE: only offered as rectangular, fullsize (placed lengthwise)
(12" W x 20" D [305 mm x 508 mm])
3. Electronic Control Assembly can be
mounted on either side of the
Condensing Unit or remotely mounted
up to 4 feet (1219 mm) from the unit
(cannot be mounted in front of the
condensing coil
1.14"
(29 mm)
All Mode ls
Slant Option
(gray highlight)
Model CWB-S1
with optional slant kit
3.5"
(89 mm)
5˚ slant
All Mode ls
False Bottom Accessory
1-part or 2-part, depending
on pan size
Placed on bottom of unit
Model CWB-S1, -S2, -S3, -S4
FRONT VIEW
Condensing unit can be rotated only 180º (not 90º)
CWB-S2, -S3, -S4 condensing units can also be mounted
as shown or moved every 5"(123 mm) to the left (away from drain)
under the refrigerated unit.
CWB-S1: 27.06" (687 mm)
CWB-S2: 48.125" (1222 mm)
CWB-S3: 69.19" (1757 mm)
CWB-S4: 90.25" (2292 mm)
Air Flow
Drain
plumbing to be
installed per local codes.
Air Flow
12.03"
(306 mm)
6.48" (165 mm) for CWB-S2, S3, S4
4" (102 mm) for CWB-S1
SIDE VIEW
CWB-S1 only
18.94"
(481 mm)
32.62"
(829 mm)
SIDE VIEW
CWB-S2, -S3, -S4
18.94"
(481 mm)
25.04"
(636 mm)
HATCO CORPORATION
(800) 558-0607
Form No. CWB-S Spec Sheet Page 2 of 3 May 2016
(414) 671- 6 350
l
l
www.hatcocorp.com
l
P.O. Box 340500 Milwaukee, WI 53234-0500 U.S.A.
l
equipsales@hatcocorp.com
intlsales@hatcocorp.com
l
Page 3
Refrigerated Slim Drop-In Wells
Models: CWB-S1, -S2, -S3, -S4
(A)
Well Opening
(B)
SPECIFICATIONS
Refrigerated Slim Drop-In Wells
Cutout Dimensions for Slim Refrigerated Drop-In Wells
Model Minimum Width (A) Maximum Width (A) Minimum Depth (B) Maximum Depth (B)
CWB-S1
CWB-S2
CWB-S3
CWB-S4
25.22" (641 mm)
46.25" (1175 mm)
67.31" (1710 mm)
88.375" (2245 mm)
26.06" (662 mm)
47.09" (1196 mm)
68.16" (1731 mm)
89.22" (2266 mm)
17.06" (433 mm) 17.94" (456 mm)
Dimensions
*
Model
CWB-S1
CWB-S2
CWB-S3
CWB-S4
*
Models shipped with electronic temperature control, pan support bars for full-size pans, condensing unit (can be rotated 180º), auto-defrost, sight glass,
service valves and dryer.
†
Shipping weights are approximate.
PLUG CONFIGURATIONS
(Width x Depth x Height)
27.06" x 18.94" x 32.62"
(687 x 481 x 829 mm)
48.125" x 18.94" x 25.04"
(1222 x 481 x 636 mm)
69.19" x 18.94" x 25.04"
(1757 x 481 x 636 mm)
90.25" x 18.94" x 25.04"
(2292 x 481 x 636 mm)
NE M A 5 -15P
Volts
120
HP Compressor
Size
1/4 804 6.7
1/4 804 6.7 5-15P 180 lbs. (82 kg)
1/3 1044 8.7 5-15P 235 lbs. (107 kg)
1/2 1380 11.5 5-15P 290 lbs. (132 kg)
Watts Amps Phase Plug Ship Weight
5-15P 133 lbs. (60 kg)
Single
†
PRODUCT SPECS
Refrigerated Slim Drop-In Wells
The NSF 7 approved Refrigerated Slim Drop-in Well shall be a Model ... as
manufactured by the Hatco Corporation, Milwaukee, WI 53234 U.S.A.
With 24/7 parts and service assistance (U.S. and Canada only), the Refrigerated Slim
Drop-in Well shall be rated at ... watts, ... volts, ... hp, and be .... inches (millimeters)
in overall width and be ... inches (millimeters) in overal depth. It shall utilize R-404A
refrigerant and consist of aluminized steel housing with a stainless bezel, an
HATCO CORPORATION
(800) 558-0607
Form No. CWB-S Spec Sheet Page 3 of 3 May 2016
(414) 671- 6 350
l
l
www.hatcocorp.com
l
electronic temperature control, pan support bars for full-size pans, condensing
unit (can be rotated 180º), compressor, flexible refrigerant lines, sight glass, service
valves, receiver, and dryer/filter.
Accessories may include pan support bars, false bottom, trivets and stainless steel
food pans.
Warranty consists of 24/7 parts and service assistance (U.S. and Canada only).
P.O. Box 340500 Milwaukee, WI 53234-0500 U.S.A.
l
equipsales@hatcocorp.com
intlsales@hatcocorp.com
l
Loading...