Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
Visit our website at: http://www.harborfreight.com
REV 14f
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 2007 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Email our technical support at: productsupport@harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Table of Contents
Safety ......................................................... 2
Specifications ............................................. 8
Setup .......................................................... 8
SAFETY OPERATION MAINTENANCESETUP
Operation .................................................... 9
Maintenance .............................................. 12
Parts List and Diagram .............................. 14
Warranty .................................................... 16
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that
follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
IMPORTANT SAFETY INFORMATION
General Power Tool Safety Warnings
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term ″power tool″ in the warnings refers to your mains-operated (corded) power tool.
Work Area Safety
1. Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
2. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
Page 2 For technical questions, please call 1-888-866-5797. Item 62203
3. Keep children and bystanders
away while operating a power tool.
Distractions can cause you to lose control.
Electrical Safety
1. Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with grounded
power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
2. Avoid body contact with grounded surfaces
such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is grounded.
3. Do not expose power tools to rain or wet
conditions. Water entering a power tool
will increase the risk of electric shock.
Personal Safety
1. Stay alert, watch what you are doing
and use common sense when operating
a power tool. Do not use a power
tool while you are tired or under the
influence of drugs, alcohol or medication.
A moment of inattention while operating power
tools may result in serious personal injury.
2. Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
4. Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil,
sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
5. When operating a power tool outdoors,
use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor
use reduces the risk of electric shock.
6. If operating a power tool in a damp location
is unavoidable, use a Ground Fault Circuit
Interrupter (GFCI) protected supply.
Use of a GFCI reduces the risk of electric shock.
4. Remove any adjusting key or wrench
before turning the power tool on.
A wrench or a key left attached to a rotating part
of the power tool may result in personal injury.
5. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or
jewelry. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewelry
or long hair can be caught in moving parts.
SAFETYOPERATIONMAINTENANCE SETUP
3. Prevent unintentional starting.
Ensure the Trigger is in the off-position before
connecting to power source, picking up or
carrying the tool.
Carrying power tools with your finger on
the Trigger or energizing power tools that
have the Trigger on invites accidents.
Power Tool Use and Care
1. Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job better and
safer at the rate for which it was designed.
2. Do not use the power tool if the Trigger
does not turn it on and off.
Any power tool that cannot be controlled with the
Trigger is dangerous and must be repaired.
7. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust‑related hazards.
8. Only use safety equipment that has been
approved by an appropriate standards agency.
Unapproved safety equipment may not provide
adequate protection. Eye protection must be
ANSI-approved and breathing protection
must be NIOSH-approved for the
specific hazards in the work area.
3. Disconnect the plug from the power source
before making any adjustments, changing
accessories, or storing power tools.
Such preventive safety measures reduce the
risk of starting the power tool accidentally.
4. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions
to operate the power tool. Power tools are
dangerous in the hands of untrained users.
Page 3For technical questions, please call 1-888-866-5797.Item 62203
5. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
7. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
SAFETY OPERATION MAINTENANCESETUP
6. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
Service
Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
Pipe Threader Safety Warnings
1. Secure the pipe being threaded
with the Clamp before use.
2. Fully engage the direction switch in the “in” or
“out” position before use.Maintain labels and
nameplates on the tool.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
3. Avoid unintentional starting.
Prepare to begin work before turning on the tool.
4. Do not lay the tool down until it has come to
a complete stop. Moving parts can grab the
surface and pull the tool out of your control.
5. When using a handheld power tool,
maintain a firm grip on the tool with both
hands to resist starting torque.
6. Do not leave the tool unattended when it is plugged
into an electrical outlet. Turn off the tool, and
unplug it from its electrical outlet before leaving.
7. This product is not a toy.
Keep it out of reach of children.
8. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.
In addition, people with pacemakers should:
• Avoid operating alone.
• Do not use with Trigger locked on.
• Properly maintain and inspect to avoid
electrical shock.
• Properly ground power cord. Ground Fault Circuit
Interrupter (GFCI) should also be implemented
– it prevents sustained electrical shock.
9. WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities, contains chemicals known to the State
of California to cause cancer and birth defects or
other reproductive harm. Some examples of these
chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement or other
masonry products
• Arsenic and chromium from chemically
treated lumber
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
(California Health & Safety Code § 25249.5, et seq.)
10. WARNING: The cord of this product contains
lead, a chemical known to the State of California
to cause cancer, and birth defects or other
reproductive harm. Wash hands after handling.
(California Health & Safety Code § 25249.5, et seq.)
11. The warnings, precautions, and instructions
discussed in this instruction manual cannot cover all
possible conditions and situations that may occur.
It must be understood by the operator that
common sense and caution are factors
which cannot be built into this product,
but must be supplied by the operator.
Page 4 For technical questions, please call 1-888-866-5797. Item 62203
Vibration Safety
This tool vibrates during use.
Repeated or long-term exposure to vibration may
cause temporary or permanent physical injury,
particularly to the hands, arms and shoulders.
To reduce the risk of vibration-related injury:
1. Anyone using vibrating tools regularly or for
an extended period should first be examined
by a doctor and then have regular medical
check-ups to ensure medical problems are not
being caused or worsened from use. Pregnant
women or people who have impaired blood
circulation to the hand, past hand injuries,
nervous system disorders, diabetes, or
Raynaud’s Disease should not use this tool.
If you feel any symptoms related to vibration (such
as tingling, numbness, and white or blue fingers),
seek medical advice as soon as possible.
SAVE THESE INSTRUCTIONS.
2. Do not smoke during use. Nicotine reduces
the blood supply to the hands and fingers,
increasing the risk of vibration-related injury.
3. Wear suitable gloves to reduce the
vibration effects on the user.
4. Use tools with the lowest vibration
when there is a choice.
SAFETYOPERATIONMAINTENANCE SETUP
5. Include vibration-free periods each day of work.
6. Grip tool as lightly as possible (while still keeping
safe control of it). Let the tool do the work.
7. To reduce vibration, maintain the tool as
explained in this manual. If any abnormal
vibration occurs, stop use immediately.
Page 5For technical questions, please call 1-888-866-5797.Item 62203
Grounding
SAFETY OPERATION MAINTENANCESETUP
grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have
it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed by
a qualified electrician.
TO PREVENT ELECTRIC SHOCK AND DEATH FROM
INCORRECT GROUNDING WIRE CONNECTION:
Check with a qualified electrician if you are in doubt as to whether the outlet is properly
grounded. Do not modify the power cord plug provided with the tool. Never remove the
Grounded Tools: Tools with Three Prong Plugs
2. The grounding prong in the plug is connected
through the green wire inside the cord to the
grounding system in the tool. The green wire
in the cord must be the only wire connected to
the tool’s grounding system and must never
be attached to an electrically “live” terminal.
(See 3-Prong Plug and Outlet.)
3. The tool must be plugged into an appropriate outlet,
3-Prong Plug and Outlet
1. Tools marked with “Grounding Required” have
a three wire cord and three prong grounding
plug. The plug must be connected to a properly
grounded outlet. If the tool should electrically
malfunction or break down, grounding provides
a low resistance path to carry electricity away
from the user, reducing the risk of electric shock.
(See 3-Prong Plug and Outlet.)
properly installed and grounded in accordance
with all codes and ordinances. The plug and outlet
should look like those in the preceding illustration.
(See 3-Prong Plug and Outlet.)
Double Insulated Tools: Tools with Two Prong Plugs
1. Tools marked “Double Insulated” do not
require grounding. They have a special
double insulation system which satisfies
OSHA requirements and complies with
the applicable standards of Underwriters
Laboratories, Inc., the Canadian Standard
Association, and the National Electrical Code.
2. Double insulated tools may be used in either of the
Outlets for 2-Prong Plug
120 volt outlets shown in the preceding illustration.
(See Outlets for 2-Prong Plug.)
Extension Cords
1. Grounded tools require a three wire extension cord.
Double Insulated tools can use either
a two or three wire extension cord.
2. As the distance from the supply outlet increases,
you must use a heavier gauge extension cord.
Using extension cords with inadequately sized wire
causes a serious drop in voltage, resulting in loss of
power and possible tool damage. (See Table A.)
3. The smaller the gauge number of the wire, the
greater the capacity of the cord. For example,
a 14 gauge cord can carry a higher current
than a 16 gauge cord. (See Table A.)
4. When using more than one extension cord
to make up the total length, make sure
each cord contains at least the minimum
wire size required. (See Table A.)
Page 6 For technical questions, please call 1-888-866-5797. Item 62203
5. If you are using one extension cord for more
than one tool, add the nameplate amperes
and use the sum to determine the required
minimum cord size. (See Table A.)
6. If you are using an extension cord outdoors, make
sure it is marked with the suffix “W-A” (“W” in
Canada) to indicate it is acceptable for outdoor use.
7. Make sure the extension cord is properly wired
and in good electrical condition. Always replace
a damaged extension cord or have it repaired
by a qualified electrician before using it.
8. Protect the extension cords from sharp objects,
excessive heat, and damp or wet areas.
Symbology
TABLE A: RECOMMENDED MINIMUM WIRE
GAUGE FOR EXTENSION CORDS* (120/240 VOLT)
NAMEPLATE
AMPERES
(at full load)
0 – 2.0 18 18 18 18 16
2.1 – 3.4 18 18 18 16 14
3.5 – 5.0 18 18 16 14 12
5.1 – 7.0 18 16 14 12 12
7.1 – 12.0 18 14 12 10 -
12.1 – 16.0 14 12 10 - -
16.1 – 20.0 12 10 - - -
* Based on limiting the line voltage drop to five volts at
150% of the rated amperes.
EXTENSION CORD
LENGTH
25´ 50´ 75´ 100´ 150´
SAFETYOPERATIONMAINTENANCE SETUP
V
~
A
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
Volts
Alternating Current
Amperes
n0 xxxx/min.
No Load Revolutions per Minute (RPM)
WARNING marking concerning Risk
of Eye Injury. Wear ANSI-approved
safety goggles with side shields.
Read the manual before
set-up and/or use.
WARNING marking
concerning Risk of Fire.
Do not cover ventilation ducts.
Keep flammable objects away.
WARNING marking concerning
Risk of Electric Shock.
Properly connect power cord
to appropriate outlet.
Page 7For technical questions, please call 1-888-866-5797.Item 62203
Specifications
Electrical Rating 120VAC / 60Hz / 12A
1/2", 3/4", 1" & 1-1/4" dies marked
with NPT and sizing (included)
SAFETY OPERATION MAINTENANCESETUP
Die Size
Setup - Before Use:
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
Note: For additional information regarding the parts listed in the
following pages, refer to Parts List and Diagram on page 14.
Functions
3110123
Direction
Safety button
on other side
Trigger
Switch
Dies
Front
Handle
Clamp
Rod Slot
Die Holder
Clamp
Lever
Clamp Rod
Clamp
Page 8 For technical questions, please call 1-888-866-5797. Item 62203
Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
Tool Set Up
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Make sure that the Trigger is in the off-position and unplug the tool from its
electrical outlet before performing any procedure in this section.
1. Select the appropriate Die for
the pipe to be threaded.
Note: Dies are intended for use on
standard schedule 40 steel pipe.
2. Insert Die into the Die Holder of the
Pipe Threader. (See Figure A.) Make sure the
Die is secured in place before proceeding.
Note: Dies can be inserted from either side
of Pipe Threader, provided the Clamp and
rotation direction are properly configured.
Note: Dies are held in place with a retaining ring, so
removing a properly-inserted Die may require light
tapping with a wooden mallet (sold separately).
3. Fill the Oil Can with Thread Cutting Oil
(not included). Keep it nearby during
the threading operation.
SAFETYOPERATIONMAINTENANCE SETUP
Figure A
Page 9For technical questions, please call 1-888-866-5797.Item 62203
Workpiece and Work Area Set Up
1. Designate a work area that is clean and well lit.
The work area must not allow access by children
or pets to prevent distraction and injury.
SAFETY OPERATION MAINTENANCESETUP
2. Route power cord along a safe route to reach
the work area without creating a tripping hazard
or exposing the power cord to possible damage.
Power cord must reach the work area with enough
extra length to allow free movement while working.
3. There must not be objects, such as utility lines,
nearby that will present a hazard while working.
4. Use Clamp assembly to secure and support
pipe during threading operation. Screw Clamp
Rod into Clamp. Make sure pipe is secured
to Clamp assembly and is supported during
threading operation. (See Figure B.)
5. Install Clamp Rod into Clamp Rob Slot. Ensure
Clamp Lever can be adjusted easily from above. Be
certain that pipe has enough clearance to proceed.
Note: Pipe end to be threaded must
be clean and chamfered.
6. Insert pipe into toothless end of Die.
Make sure inside diameter of Die matches
outside diameter of pipe. (See Figure C.)
Clamp
Die
Rod Slot
Clamp
Rod
Figure B
Pipe
Figure C
Page 10 For technical questions, please call 1-888-866-5797. Item 62203
General Operating Instructions
1. Make sure pipe end and threads of Die are
sufficiently oiled at all times. (See Figure D.)
Otherwise, the life of the Die Blades will be
shortened and the threads will be rough.
Figure D
2. The Direction Switch determines the direction of
the threading operation. Flip Rotating Direction
Switch to right position (arrow should point toward
head of Threader) for a clockwise rotation.
3. Make sure Trigger is in off-position, then plug in tool.
4. While holding Handle, press Trigger in and
squeeze Handle. Pipe Threader will not
engage until Safety Handle is firmly grasped.
Apply pressure until Die engages pipe, cutting
two to three threads. See Figure E.
5. From this point, the Die will automatically be drawn
over the pipe and a standard taper thread will be cut.
6. To ensure a good, clean standard taper
thread, stop Pipe Threader every few turns,
reverse, oil pipe, and re-cut thread.
7. Stop threading when the end of the Die is flush
with the end of the pipe. At this point, the correct
thread length has been reached to produce
the proper joint. To continue beyond this point
would make a straight or running thread.
8. To finish threading operation:
a. Release Power Switch. Allow Pipe
Threader to completely stop.
b. Reverse Direction Switch.
c. Squeeze Power Switch to turn on Pipe
Threader. Allow Die to reverse path of
thread until it has fully expelled pipe.
d. Release Power Switch. Avoid damaging
newly cut threads when removing
pipe from Pipe Threader.
CAUTION! Freshly cut threads may be hot and have
sharp edges or sharp metal turnings still attached.
Clean pipe and allow it to cool before use.
9. IMPORTANT: Clean any oil spills on the ground.
At the end of each job, clean Pipe Threader
and store in a clean, dry, safe location out of
reach of children and unauthorized people.
10. To prevent accidents, turn off tool and
unplug it after use. Clean, then store
tool indoors out of children’s reach.
SAFETYOPERATIONMAINTENANCE SETUP
Figure E
Page 11For technical questions, please call 1-888-866-5797.Item 62203
Maintenance and Servicing
Procedures not specifically explained in this manual must
be performed only by a qualified technician.
SAFETY OPERATION MAINTENANCESETUP
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Make sure that the Trigger is in the off-position and unplug the tool from its
electrical outlet before performing any procedure in this section.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:
Do not use damaged equipment. If abnormal noise or vibration
occurs, have the problem corrected before further use.
Cleaning, Maintenance, and Lubrication
1. BEFORE EACH USE, inspect the general
condition of the tool. Check for:
• loose hardware,
• misalignment or binding of moving parts,
• damaged cord/electrical wiring,
• cracked or broken parts, and
• any other condition that may
affect its safe operation.
To replace the Die Blades
1. Worn Die Blades can result in poor thread
quality. When replacing Die Blades, verify that
the size of the new Die Blades corresponds
to the size of the Die (1/2″, 3/4″, 1″, or
1-1/4″). To replace the Die Blades:
a. Remove the four Screws on the Die.
b. Remove the Chrome Ring from the Die.
2. AFTER USE, wipe external surfaces
of the tool with clean cloth.
3.
4
WARNING! If the supply cord of this
power tool is damaged, it must be replaced
only by a qualified service technician.
c. Remove all four Die Blades.
d. Insert four new Die Blades into the Die.
NOTE: When inserting the Die Blades, make
sure the cutting edges of the Die Blades
face inward and that the number on each
Die Blade is at the top and in sequence.
e. Once the Die Blades are properly inserted,
replace the Chrome Ring and four Screws.
3
Die Blade
2
1
Chrome Ring
Page 12 For technical questions, please call 1-888-866-5797. Item 62203
Die
Blade
Number
Troubleshooting
Problem Possible Causes Likely Solutions
Tool will not start. 1. Cord not connected.
2. No power at outlet.
3. Tool’s thermal reset breaker
tripped (if equipped).
4. Internal damage or wear.
(Carbon brushes or
Trigger, for example.)
Tool operates slowly. 1. Forcing tool to work too fast.
2. Extension cord too long or cord
diameter too small.
Performance
decreases over time.
Excessive noise
or rattling.
Overheating. 1. Forcing tool to work too fast.
Pipe doesn’t fit Die. 1. Die is inappropriate to pipe size.
Pipe spins. Clamp is upside-down for
Dies break. 1. Die Blades insufficiently
Carbon brushes worn or damaged. Have qualified technician replace brushes.
Internal damage or wear. (Carbon
brushes or bearings, for example.)
2. Blocked motor housing vents.
3. Motor being strained by long or
small diameter extension cord.
2. Pipe inserted from wrong side.
3. Pipe not chamfered.
the rotation direction.
lubricated.
2. Die Blades installed in wrong
order or backwards.
1. Check that cord is plugged in.
2. Check power at outlet. If outlet is unpowered,
turn off tool and check circuit breaker.
If breaker is tripped, make sure circuit is right
capacity for tool and circuit has no other loads.
3. Turn off tool and allow to cool.
Press reset button on tool.
4. Have technician service tool.
1. Allow tool to work at its own rate.
2. Eliminate use of extension cord. If an extension
cord is needed, use one with the proper diameter
for its length and load. See Extension Cords
in Grounding section on page 6.
Have technician service tool.
1. Allow tool to work at its own rate.
2. Wear ANSI-approved safety goggles and
NIOSH-approved dust mask/respirator while
blowing dust out of motor using compressed air.
3. Eliminate use of extension cord. If an extension
cord is needed, use one with the proper diameter
for its length and load. See Extension Cords
in Grounding section on page 6.
1. Choose a Die appropriate to the pipe.
2. Insert pipe from correct side. See Workpiece
and Area Set Up on page 10.
3. Make sure pipe end-to-be-threaded is chamfered.
Move Clamp Bar to other side of Clamp. Turn
Clamp upside down and reclamp it to pipe. See
Workpiece and Area Set Up on page 10.
1. Lubricate Die Blades sufficiently. See General
Operating Instructions section on page 11.
2. Ensure cutting edges of Blades face inward
and the number on each Die Blade is at
the top and in sequence. See To replace
the Die Blades section on page 12.
SAFETYOPERATIONMAINTENANCE SETUP
Follow all safety precautions whenever diagnosing or servicing the tool.
Disconnect power supply before service.
Page 13For technical questions, please call 1-888-866-5797.Item 62203
Parts List and Diagram
PLEASE READ THE FOLLOWING CAREFULLY
SAFETY OPERATION MAINTENANCESETUP
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Parts List
Part Description Qty
1 M5 Nut 6
2 Left Head Housing 1
3 Die Holder 1
4 Ø52 Retaining Ring 1
5 M5X22 Screw 6
6 Right Head Housing 1
7 Ø5 Washer 4
8 Ø5 Washer 4
9 ST4.9x35 Screw 2
10 Cap 1
11 Ø12 Retaining Ring 2
12 Bearing (Ø17xØ12x12) 2
13 Plane Bearing 51101 2
14 Worm Gear 1
15 Key (5x6) 1
16 Gear 1
17 Ø12 Retaining Ring 1
18 629 Bearing 1
19 Armature 1
20 608 Bearing 1
21 608 Bearing Sheath 1
22 Cover 1
23 ST3.9x75 Screw 2
24 Stator 1
25 Housing 1
Part Description Qty
26 Nameplate 1
27 Carbon Brush Holder 2
28 Carbon Brush 2
29 Carbon Brush Cover 2
30 Right Handle 1
31 ST3.9x16 Screw 3
32 ST3.9x45 Screw 4
33 Direction Switch 1
34 Trigger 1
35 Left Handle 1
36 Cord Clamp 1
37 Cord Protector 1
38 Power Cord 1
39 Roll Pin 1
40 Clamp 1
41 Clamp Bar 1
42 1/2" Die 1
42a 1/2" Die Blade Set -
43 3/4" Die 1
43a 3/4" Die Blade Set -
44 1" Die 1
44a 1" Die Blade Set -
45 1-1/4" Die 1
45a 1-1/4" Die Blade Set -
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
Page 14 For technical questions, please call 1-888-866-5797. Item 62203
Assembly Diagram
SAFETYOPERATIONMAINTENANCE SETUP
Page 15For technical questions, please call 1-888-866-5797.Item 62203
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797
Loading...