Harbor Freight Tools Oil Suction Gun Product manual
Specications
Oil Suction Gun
Item 95464
INSTRUCTIONS AND
PRECAUTIONS
Read this material before using
this product. Failure to do so
can result in serious injury.
SAVE THIS MANUAL.
When unpacking, make sure that the
product is intact and undamaged.
If any parts are missing or broken,
please call 1‑800‑444‑3353
as soon as possible.
Copyright© 2006 by Harbor Freight Tools®.
All rights reserved. No portion of this document
or any artwork contained herein may be
reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
Diagrams within this document may not be drawn
proportionally. Due to continuing improvements,
actual product may differ slightly from the product
described herein.
Manual Revised 11g
Capacity 16.9 oz.
Hose Dimensions 12 IN. L x 1/2 IN. O.D.
Important Safety Information
1. Wear ANSI‑approved safety goggles
and heavy‑duty work gloves during use.
2. Keep work area clean and well lit.
3. Keep bystanders out of the work area.
4. Do not use when tired or when under
the inuence of drugs or medication.
5. This product is not a toy. Keep out
of reach of children.
6. Use as intended only. Use only
with non‑corrosive lubricants.
Do not use with gasoline.
7. Inspect before every use; do not
use if parts are loose or damaged.
8. Recycle or dispose of oil
properly in accordance with all
local laws and regulations.
9. Do not use near open ame
or other ignition sources.
10. When transferring oil, make certain
that uid is sufciently cool prior to
transfer. If transferring from a vehicle,
make sure vehicle’s engine is off, and
oil and engine components are cool.
Visit our website at:
http://www.harborfreight.com
Email our technical support at:
tech@harborfreight.com
For technical questions,
please call 1‑800‑444‑3353.
Operating Instructions
Parts List and Diagram
Inspect tool before use, looking
for damaged, loose, and
missing parts. If any problems
are found, do not use tool until repaired.
To Drain Fluid
1. Submerge the Hose into the lubricant
that you desire to transfer.
2. Holding onto the Tube with one hand,
grasp the Handle with your other hand.
3. Pull up on the Handle to create
suction and ll up the Tube. Use a
rag on hose end to prevent dripping.
4. Place the Oil Suction Gun over a
collection receptacle (not included)
that can be closed and covered for
transfer. Push down on the Handle
or unscrew the Front Cover and
pour lubricant out from the Tube
into the collection receptacle.
To Fill With Fluid
1. Fill the Tube using the above steps.
2. Push down on the Handle to inject
lubricant from the Hose into the
transmission, clutch or differential.
Part Description Qty.
1 Handle 1
2 Rear Cover 1
3 Rubber Gasket 2
4 Tube 1
5 Front Cover 1
6 Nozzle 1
7 Hose 1
8 Spring 1
9 Follower Rod 1
10 Spacer 2
11 Plunger 1
12 Hex Nut 1
Note: Some parts are listed and shown
for illustration purposes only, and are not
available individually as replacement parts.
PLEASE READ THE
FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR
HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS DOCUMENT AS A REFERENCE
TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION
OR WARRANTY OF ANY KIND TO THE BUYER
THAT HE OR SHE IS QUALIFIED TO MAKE ANY
REPAIRS TO THE PRODUCT, OR THAT HE OR SHE
IS QUALIFIED TO REPLACE ANY PARTS OF THE
PRODUCT. IN FACT, THE MANUFACTURER AND/
OR DISTRIBUTOR EXPRESSLY STATES THAT ALL
REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS, AND NOT BY THE BUYER. THE
BUYER ASSUMES ALL RISK AND LIABILITY ARISING
OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO,
OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
Page 2 For technical questions, please call 1‑800‑444‑3353. SKU 95464
Loading...