Harbor Freight Tools Multi Use Transfer Pump Product manual
Multi-Use Transfer Pump
Specications
Item 66418
INSTRUCTIONS
AND PRECAUTIONS
Visit our website at:
http://www.harborfreight.com
Read this material before
using this product.
Failure to do so can result
in serious injury.
SAVE THIS MANUAL.
When unpacking, make sure that the
product is intact and undamaged.
If any parts are missing or broken,
please call 1‑800‑444‑3353
as soon as possible.
Copyright© 2008 by Harbor Freight Tools®.
All rights reserved. No portion of this document
or any artwork contained herein may be
reproduced in any shape or form without the
express written consent of Harbor Freight
Tools. Diagrams within this document may
not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly
from the product described herein. Tools required
for assembly and service may not be included.
For technical questions or replacement
parts, please call 1-800-444-3353.
Manual Revised 11f
Operation
Method
Dipstick
Tubing Size
Functions
Hand Pump
1/4 IN. D x 47 IN. L
Air Pressure Ination
Low Viscosity Fluid Transfer
Important Safety Information
1. Wear ANSI‑approved safety
goggles and heavy‑duty
work gloves during use.
2. Keep area clean and well lit.
3. Do not operate when tired
or when under the inuence
of drugs or medication.
4. Do not use your mouth to help
siphon ammable liquids.
5. This product is not a toy.
Keep away from children.
6. Use as intended only.
7. Inspect before every use; do not
use if parts are loose or damaged.
8. Do not smoke in the presence of
gasoline or ammable vapors.
9. Maintain product labels and
nameplates. These carry important
safety information. If unreadable
or missing, contact Harbor
Freight Tools for a replacement.
Operating Instructions
Read the ENTIRE
IMPORTANT SAFETY
INFORMATION section
at the beginning of this
document including all
text under subheadings
therein before set up or
use of this product.
WARNING! After siphoning or
transferring gasoline or any
ammable material, rinse the pump
and hose with detergent to remove
ammable uid and fumes.
Note: Refer to the Parts List
and Assembly Diagram for
the following instructions.
Siphoning
1. Insert one end of each
of the Orange Hoses (D)
into a Connector (A).
2. Insert the Orange Hose ends
into the Pump (C) intake and
discharge ports and slide the
Connectors over the Ports.
3. Put the intake hose (near the
pump handle) into the liquid to
be pumped. Put the bottom hose
into the discharge container.
4. Pump the Handle.
Note: The discharge container must
be lower than the intake hose.
Note: You will have to pump
three to four times before the
liquid will start to ow.
Pumping Air
1. Attach a Connector (A) to the
Air Pressure Hose (E).
2. Insert the hose into the
Pump (C) discharge port.
Press rmly into the port.
Slide the Connector over the port.
3. Lift up the air chock lever on
the Air Pressure Hose, and
insert the Inator Adapter (G)
into the chock. Fold back the
lever to lock the Adapter.
4. Insert the Adapter into the
beach ball or air mattress
inator tube and commence
pumping the handle to inate.
Oil/Fuel Transfer
1. Attach the Orange Hoses as
instructed in steps 1 and 2
under Siphoning.
2. Squeeze one end of Dipstick Tube
(F) into the Tapered Adapter (B)
until snug. Insert the free end of the
tube into the engine dipstick port
and while rotating the tube in either
a clockwise or counterclockwise
direction, feed the tube in until it
bottoms up in the engine sump.
3. Attach the tapered end of the
Adapter (B) into the end of
Orange Hose of the Intake Port.
4. Put the Hose connected
to the discharge port in
the target container.
5. Pump the handle to discharge
the oil into the container.
Note: The end of discharge hose
must be located below engine sump.
Page 2 For technical questions, please call 1-800-444-3353. SKU 66418
Loading...