Harbor Freight Tools Motorcycle Wheel Cleaning Stand Product manual
WHEEL
CLEANING
98800
STAND
INSTRUCTIONS AND PRECAUTIONS
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
SAVE THESE INSTRUCTIONS. READ ALL
PRECAUTIONS AND INSTRUCTIONS.
Copyright© 2008 by Harbor Freight Tools®. All rights reserved. No portion of this document or any artwork contained
herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this document may not be drawn proportionally. Due to continuing improvements, actual product
may differ slightly from the product described herein. Tools required for assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
SPECIFICATIONS
Maximum Weight Capacity 500 Lbs.
Dimensions 12” L x 9-1/16” W x 1-1/2” H
Roller Dimensions 1-1/4’ dia. x 7-1/2”
UNPACKING
When unpacking, check to make sure that
the item is intact and undamaged. If any parts are
missing or broken, please call Harbor Freight Tools
at the number shown on the cover of this document
as soon as possible.
IMPORTANT SAFETY
INFORMATION
Assembly Precautions
Assemble only according to these instruc-1.
tions. Improper assembly can create hazards.
Wear ANSI-approved safety goggles and 2.
heavy-duty work gloves during use.
Do not use engine to turn wheel.3.
Keep assembly area clean and well lit.4.
Keep bystanders out of the area during as-5.
sembly.
Use the proper motorcycle wheel chock to 6.
stabilize the motorcycle. Make certain to
use a sidestand and proper support to avoid
damage to property and personal injury.
Use only on a at and level area. Do not use 7.
on sloping or uneven surfaces.
Make certain that the motorcycle engine is off 8.
and that it is not in gear during use.
Harbor Freight Tools accepts no responsibil-9.
ity for damage to property that may result
from the misuse or abuse of the Wheel
Cleaning Stand.
Do not use when tired or when under the 10.
inuence of drugs or medication.
This product is not a toy. Do not allow chil-11.
dren to play with or near this item.
Use for intended purpose only.12.
Inspect before use; do not use if parts are 13.
loose or damaged.
Maintain product labels and nameplates. 14.
These carry important safety information.
If unreadable or missing, contact Harbor
Freight Tools for a replacement.
ASSEMBLY INSTRUCTIONS
Read the ENTIRE IMPORTANT
SAFETY INFORMATION section at the
beginning of this document including
all text under subheadings therein
before set up or use of this product.
Rotate the rear wheel by hand while clean-6.
ing, polishing or maintaining the chain.
Make certain to keep the rear wheel in the 7.
center of the Wheel Cleaning Stand. If the
wheel should slide to the side of the Stand,
move it back into the center.
For front wheel cleaning, repeat steps 1 8.
through 7 as above, but placing the Cleaning
Stand ahead of the front wheel.
MAINTENANCE
Before each use, inspect the general condi-1.
tion of the Wheel Cleaning Stand. Check
for loose screws, misalignment or binding of
moving parts, cracked or broken parts, and
any other condition that may affect its safe
operation.
After each use, clean the Wheel Cleaning 2.
Stand with a soft, dry towel.
Do not use harsh chemicals or solvents to 3.
clean the Stand. Do not use abrasives or
abrasive materials to clean the Stand as this
will damage its protective nish.
Periodically lube contact points and Rollers 4.
with grease.
OPERATING INSTRUCTIONS
Place the Wheel Cleaning Stand on a at 1.
and level area capable of supporting the
Wheel Cleaning Stand and the vehicle being
cleaned.
Place the Cleaning Stand behind the rear 2.
wheel. Wheel must be at a right angle to the
direction of the wheel to be cleaned.
Manually roll the motorcycle up the Ramp (9) 3.
and onto the Wheel Cleaning Stand. Make
certain that the rear motorcycle wheel has
rolled over the rst roller and sits between
both Rollers (8). See Parts Diagram on page
3.
Allow the rear wheel to fully rest between 4.
Rollers (8). Set the motorcycle onto its kick-
stand. If the motorcycle is leaning too much,
it’s necessary to place a proper block under
the kickstand to reduce the leaning problem.
Use a Motorcycle Wheel Chock (available 5.
through Harbor Freight Tools) to secure the
free wheel.
Record Serial Number Here:
Note: If product has no serial number, record
month and year of purchase instead.
Note: Some parts are listed and shown for illustra-
tion purposes only, and are not available
individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS
PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS DOCUMENT AS A REFERENCE TOOL ONLY.
NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY
KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED
TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT
HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF
THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS
AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT
BY THE BUYER. THE BUYER ASSUMES ALL RISK AND
LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO,
OR ARISING OUT OF HIS OR HER INSTALLATION OF
REPLACEMENT PARTS THERETO.
SKU 98800 For technical questions, please call 1-800-444-3353. Page 2
Loading...