Harbor Freight Tools Motorcycle Tire Changer Attachment Product manual
Table of Contents
Safety ......................................................... 2
Specifications ............................................. 3
Setup .......................................................... 4
SAFETY OPERATION MAINTENANCESETUP
Operation .................................................... 5
Maintenance ............................................... 9
Parts List and Diagram .............................. 10
Warranty .................................................... 12
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that
follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
Page 2 For technical questions, please call 1-800-444-3353. Item 60810
IMPORTANT SAFETY INFORMATION
Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in serious injury or death.
Save all warnings and instructions for future reference.
General Safety Warnings
1. Deflate tire completely before changing.
2. Do not use old or repaired tires or tubes.
Replacement tires or tubes must be new.
3. Do not exceed rated rim capacity.
4. Wear ANSI-approved safety goggles and
heavy-duty work gloves during assembly and use.
5. Read manual before use.
6. Inspect before every use; do not use
if parts loose or damaged.
7. This product can only be used with Pittsburgh
Automotive Portable Tire Changer.
8. Do not change automobile tires with this
product. For use with motorcycle tires only.
9. Keep the work area clean and well
lit. Cluttered and dark areas increase
the risks of injury to persons.
SAFETYOPERATIONMAINTENANCE SETUP
12. Do not use Motorcycle Tire Changer
Attachment while tired or under the
influence of drugs, alcohol, or medication.
A moment of inattention while operating the
tool increases the risk of injury to persons.
13. Do not overreach. Keep proper
footing and balance at all times.
Proper footing and balance enables better
control of the tool in unexpected situations.
14. Assemble only according to these instructions.
Improper assembly can create hazards.
15. This product is not a toy. Do not allow
children to play with or near this item.
16. Use as intended only.
17. Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
10. Keep bystanders, children, and visitors away
while operating the tool. Distractions are
able to result in the loss of control of the tool.
11. Stay alert. Watch what you are doing and
use common sense when operating the
Motorcycle Tire Changer Attachment.
SAVE THESE INSTRUCTIONS.
Specifications
Rim Capacity
18. The warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by the
operator that common sense and caution are
factors which cannot be built into this product,
but must be supplied by the operator.
11" - 25" Diameter
Page 3For technical questions, please call 1-800-444-3353.Item 60810
Assembly Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document
including all text under subheadings therein before set up or use of this product.
SAFETY OPERATION MAINTENANCESETUP
Note: For additional information regarding the parts listed in the following pages, refer to Parts List and
Assembly Diagram on page 10 and Owner’s Manual for Pittsburgh Automotive Portable Tire Changer.
1. Attach Adjustable Support Tube (8) and Support
Tubes (5) to Base (9) with Bolts (12) and Nuts (13).
2. Thread Bolts (11) loosely into
Adjustable Wheel Clamp.
3. Thread Knob (10) into Base. (See Figure A.)
Support
Adjustable
Clamp (14)
Adjustable
Support
Tube (8)
Wheel
Bolts
(11)
Base
(9)
Figure A
Tubes
(5)
Nuts
(13)
Bolts
(12)
Knob
(10)
6. Attach Vertical Support Bar (3) to Adjustable Support
Tube and secure with Bolt (12) and Nut (13).
7. Attach Support Arm (2) to Vertical Support Bar
and secure with Bolt (12) and Nut (13).
8. Slide Center Post (1) down Support Arm tube and
into Base. Thread Knob (10) into Support Arm.
9. Secure Center Post by tightening
Knob. (See Figure C.)
Support
Nut
(13)
Vertical
Support
Bar (3)
Arm (2)
Bolt
(12)
Knob
(10)
Center
Post (1)
4. Mount Motorcycle Tire Changer Attachment
Base over Portable Tire Changer Center
Post. Secure by tightening Knob.
5. Slide Wheel Clamps (4) onto Support
Tubes and secure with Pins (6) and
R-Clips (7). (See Figure B.)
Wheel
Clamps (4)
R-Clip
(7)
Portable Tire
Changer
Center Post
Pin
(6)
Nut
(13)
Bolt
(12)
Figure C
Figure B
Page 4 For technical questions, please call 1-800-444-3353. Item 60810
Loading...