Harbor Freight Tools Handgun Safe Vault Product manual

Specifications

Overall dimensions 11" L x 8-1/8" W x 5-1/2" H

External AC/DC Power Socket size 3.5mm

Factory Code

This gun safe meets the California DOJ requirements.

Important Safety Information

Installation Precautions

1. Verify that installation surface has no hidden
utility lines before drilling or driving screws.

2. Wear ANSI-approved safety
goggles during installation.

3. Install only according to these instructions.
Improper installation can create hazards.

4. Keep installation area clean and well lit.

5. Keep bystanders out of the

6. Do not install when tired or when under the

7. Place the Safe on correct surface.

Use Precautions

1. Unload gun completely, including
chamber, before storing.

2. Lock up guns and ammunition
separately out of children’s
reach and out of sight.

3. Even when stored in gun safe,
use gun-lock to disable gun.

4. Separate gun keys from other keys.

5. Leaving gun unsecured may

result in criminal charges.

6. Do not allow children to play
with or near safe. Keep keys and
codes away from children.

7. Keep clear of Door when closing.

8. Position batteries in proper polarity and
do not install batteries of different types,
charge levels, or capacities together.

9. Use as intended only.

10. Inspect before every use; do not use
if parts are loose or damaged.

11. Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.

12. Do not store Keys inside of the Safe.

13. Warning: The brass components of

14. The shelf or wall the Safe is placed on must

15. The warnings, cautions, and instructions

16. The Safe is neither water nor fire proof.

NOTE: Harbor Freight Tools is not responsible
for the loss of any property stored within this safe
due to theft, fire, or any other circumstance.

area during installation.

influence of alcohol, drugs, or medication.

Only use this Safe on a stable,
level, clean and dry surface that is
capable of sustaining the load.

Place the emergency keys in a location
outside of the safe making sure they are
in a secure location that you can find.

this product contain lead, a chemical
known to the State of California to cause
birth defects (or other reproductive
harm). (California Health & Safety code

§ 25249.5, et seq.)

support the weight of the Safe and its load.

discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by the
operator that common sense and caution
are factors which cannot be built into this
product, but must be supplied by the operator.

Page 2 For technical questions, please call 1-888-866-5797. Item 61581

Installation

Read the ENTIRE IMPORTANT SAFETY INFORMATION section
at the beginning of this manual including all text under subheadings therein
before set up or use of this product.

Mounting

1. The mounting location must be able to support
the weight of both the safe and its contents.

2. Remove felt pad from inside of safe.

3. Using the holes in the bottom of the Safe
as a template, lay the Safe in the desired
location and drill all four pilot holes.

4. Once the pilot holes have been drilled, secure
the Safe with the supplied 1-1/2" wood screws.

Batteries

1. Remove the cover from the battery
compartment, found on the ceiling of the safe.

2. Insert four AA batteries, taking
note of the proper polarity.

3. Replace the battery cover.

a. Screw through the holes in the bottom of

the Safe and into the drawer bottom.

b. If the screws included with the Safe are

too long, replace them with the appropriate
length wood screws (not supplied) for
the intended mounting surface.

5. Place the supplied felt pad in the Safe so as to
cover the Safe bottom and mounting screws.

Note: Low battery is indicated by the safe
beeping four times whenever the door is
opened, and by the indicator light flashing red.

4. When low battery is indicated,
change the batteries.

Page 3For technical questions, please call 1-888-866-5797.Item 61581

Functions

External
AC/DC
Power
Socket

Keypad

Key
Hole

Indicator
Light

Mounting
Holes

Figure A

Sound
Switch

Programming

LED Light

Button

Figure B: Underside of Key Pad (inside safe)

Page 4 For technical questions, please call 1-888-866-5797. Item 61581

Battery
Compartment

Operation

Read the ENTIRE IMPORTANT SAFETY INFORMATION section
at the beginning of this manual including all text under subheadings therein
before set up or use of this product.

To prevent serious injury and DEATH from accidental firearm discharge:

1. Unload gun completely, including
chamber, before storing.

2. Lock up guns and ammunition
separately out of children’s
reach and out of sight.

3. Even when stored in gun safe,
use gun-lock to disable gun.

4. Separate gun keys from other keys.

5. Leaving gun unsecured may

result in criminal charges.

Open Safe Using Emergency Keys

1. Insert the Key into the Key Hole
(see Figure A), and turn.

2. The door will fall open.

3. Close the door by pushing up
and in, until a click is heard.

WARNING: Do not store your keys in the safe.

Set the Combination Code

Note: The safe will accept only 5-digit codes.

1. Open the door using the key or factory
code (

2. Press the programming button (see Figure B).

3. Enter the new 5-digit code.

).

4. When the safe has accepted the new code,
two beeps will be heard and the indicator
light (See Figure A) will flash twice.

Note: If no feedback is given, the
code has not been accepted.

Entering the Wrong Combination

1. If the wrong combination is entered,
the safe will beep three times.

2. If the wrong combination is entered four
consecutive times, the safe will go into
Lock-Down Mode for three minutes.

Note: During this time, the safe will beep, the
LED light (See Figure B) will flash, and the
keypad (see Figure A) will be disabled. The safe
may still be opened with the key override.

3. After three minutes, the safe will
resume normal operation.

Light and Sound

1. The LED interior light will automatically
illuminate for 30 seconds when the
door is opened with the combination
code. It will then shut off.

2. To turn the light back on, re­enter the combination code.

3. To turn the audible beeps on or off, toggle
the Sound Switch. See Figure B.

Page 5For technical questions, please call 1-888-866-5797.Item 61581

Maintenance and Servicing

Procedures not specifically explained in this manual must be performed only by a
qualified technician.

1. BEFORE EACH USE, inspect the general
condition of the Safe. Check for loose
screws, misalignment or binding of moving
parts, cracked or broken parts, damaged
electrical wiring, and any other condition
that may affect its safe operation.

2. PERIODICALLY clean external surfaces
of the Safe with a clean cloth.

3. To extend battery life, the safe may be
plugged into a power outlet through an
external 6 volt power adaptor with a standard

3.5mm tip (not included). To do so, use the

external AC/DC power socket (Figure A).

Page 6 For technical questions, please call 1-888-866-5797. Item 61581

Record Serial Number Here:

Note: If product has no serial number, record

month and year of purchase instead.

Note: Replacement parts are not
available for this item.

Page 7For technical questions, please call 1-888-866-5797.Item 61581

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality
and durability standards, and warrants to the original purchaser that this product is free from
defects in materials and workmanship for the period of 90 days from the date of purchase.
This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence
or accidents, repairs or alterations outside our facilities, criminal activity, improper installation,
normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,
injuries to persons or property, or for incidental, contingent, special or consequential damages
arising from the use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may not apply to you.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation
charges prepaid. Proof of purchase date and an explanation of the complaint must accompany
the merchandise. If our inspection verifies the defect, we will either repair or replace
the product at our election or we may elect to refund the purchase price if we cannot readily
and quickly provide you with a replacement. We will return repaired products at our expense,
but if we determine there is no defect, or that the defect resulted from causes not within
the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797