Harbor Freight Tools 96126 User Manual
4.5 HP VIBRATORY SCREED
Model
96126
ASSEMBLY AND OPERATION INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
Distributed Exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
TO PREVENT SERIOUS INJURY, READ AND UNDERSTAND
ALL WARNINGS AND INSTRUCTIONS BEFORE USE.
Copyright© 2007 by Harbor Freight Tools®. All rights reserved. No portion of this manual
or any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
SPECIFICATIONS
Gasoline Engine
Clutch Design Centrifugal Clutch
Drive Type A-710 V-Belt Drive
Engine Approvals 2006 EPA Phase II; 2006 CA Emissions Regulations
Maximum Beam Length 15’ with Spreaders
Screed Spreaders (2) 7-1/8”L x 21-1/8”W
Overall Dimensions 21-1/8”W x 34-7/8”L x 44-5/8”H
Net Weight 116 Lbs.
Robin®/5FJXS.1271GA/Model#: EX130D500216711
127 cc 4.5 HP 4-cycle engine
Save This Manual
You will need this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep your
invoice with this manual. Write the invoice number on the inside of the front cover. Write the
product’s serial number in the back of the manual near the assembly diagram, or write month
and year of purchase if product has no number. Keep this manual and invoice in a safe and
dry place for future reference.
SAFETY RULES
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS
Failure to follow all instructions listed below may result in
electric shock, fire, and/or serious injury.
SAVE THESE INSTRUCTIONS
WARNING: When using tool, basic safety precautions should always be followed to reduce
the risk of personal injury and damage to equipment.
Read all instructions before using this tool!
1.
2.
Keep work area clean. Cluttered areas invite injuries.
Observe work area conditions. Do not use machines or tools in damp or wet locations.
Don’t expose to rain. Keep work area well lit.
3.
Keep children away. Children must never be allowed in the work area. Do not let them
handle machines, or tools. Never allow children to play with or climb on Screed.
4.
Store idle equipment. When not in use, tools must be stored in a dry location to inhibit
rust. Always lock up tools and keep out of reach of children.
5.
Use the right tool for the job. Do not attempt to force a small tool or attachment to
do the work of a larger industrial tool. There are certain applications for which this
tool was designed. It will do the job better and more safely at the rate for which it was
For technical questions, please call 1-800-444-3353
Page 2SKU 96126
intended. Do not modify this tool and do not use this tool for a purpose for which it was
not intended.
6.
7.
8.
9.
10.
11.
Dress properly. Do not wear loose clothing or jewelry as they can be caught in
moving parts. Protective, electrically nonconductive clothes and nonskid footwear are
recommended when working. Wear restrictive hair covering to contain long hair.
Use eye protection. Always wear ANSI approved impact safety goggles.
Do not overreach. Keep proper footing and balance at all times. Do not reach over or
across an engine, Screed or other machines while in use.
Maintain tools with care. Keep tools clean and maintained for better and safer
performance. Follow instructions for lubricating and changing accessories. The handle
must be kept clean, dry, and free from oil and grease at all times.
Stay alert. Watch what you are doing, use common sense. Do not operate any tool
when you are tired.
Check for damaged parts. Before using any tool, any part that appears damaged
should be carefully checked to determine that it will operate properly and perform its
intended function. Check for alignment and binding of moving parts; any broken parts
or mounting fixtures; and any other condition that may affect proper operation. Any part
that is damaged should be properly repaired or replaced by a qualified technician. Do
not use the tool if any switch does not turn On and Off properly.
12.
13.
14.
15.
16.
17.
Replacement parts and accessories. When servicing, use only identical replacement
parts. Use of any other parts will void the warranty. Only use accessories intended for
use with this tool. Approved accessories are available from Harbor Freight Tools.
Do not operate tool if under the influence of alcohol or drugs. Read warning labels
if taking prescription medicine to determine if your judgment or reflexes are impaired
while taking drugs. If there is any doubt, do not operate the tool.
Be aware that prolonged exposure to vibration can lead to personal injury (which
may include hand, wrist and arm injury). If you experience discomfort or pain after
using this tool, you should contact your physician prior to further use of the tool.
Maintenance. For your safety, service and maintenance should be performed regularly
by a qualified technician.
WARNING! Stand clear of the Screed when it is in operation. Keep unnecessary
spectators away from this machine while in operation. Never ride on Screed.
WARNING! Fire Hazard. Do not fill gas tank when engine is running or hot. Do not
operate engine near spilled gasoline. Clean spilled gasoline before starting engine. Do
not store or handle gasoline near pilot light, electrical equipment or open flame. Do not
smoke near gasoline.
18.
WARNING! Carbon Monoxide Hazard. Operate Vibratory Screed in well ventilated area
only. Carbon Monoxide is created when engine is running and is a DEADLY gas when
inhaled. Carbon Monoxide is a colorless, odorless gas. Early signs of Carbon Monoxide
For technical questions, please call 1-800-444-3353
Page 3SKU 96126
Loading...