Harbor Freight Tools 95824 Owner's Manual

Specifications

Outer Dimensions 21″ W x 15″ D x 59″ H

Inner Dimensions 20-1/2″ W x 12″ D x 49-1/2″ H

Lockbox Inner Dimensions 20-1/2″ W x 11″ D x 7-5/8″ H

Dual Security System for Keyed and Keyless Access

Panel Features

Includes

8 Digit Key Pad requires (4) “C” Batteries (included)
Green LED Code OK/Open
Red LED Low Battery

(4) 8x75mm Mounting Bolts, 8-Place Hanger Rack with
Soft Foam Inserts, 6-Place Clip Rack inside door panel
2 Brass Lockbox Keys, 3 shelves, 12 shelf mounting clips

IMPORTANT SAFETY INFORMATION

Installation Precautions

1. Verify that installation surface has no hidden
utility lines before drilling or driving screws.

2. Wear ANSI-approved safety
goggles during installation.

3. Mount securely before use.

4. Install only according to these instructions.
Improper installation can create hazards.

5. Keep installation area clean and well lit.

Use Precautions

1. Keep closed and locked whenever unattended.
RISK OF CHILD ENTRAPMENT AND
SUFFOCATION.
Check inside before closing.
Do not allow children to play with or near safe.
Keep keys and codes away from children.

2. Keep clear of door when closing.

3. Position batteries in proper polarity and
do not install batteries of different types,
charge levels, or capacities together.

4. Use as intended only.

5. Inspect before every use; do not use
if parts are loose or damaged.

6. Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.

6. Keep bystanders out of the area during installation.

7. Do not install when tired or when under the
influence of alcohol, drugs or medication.

8. At least two people are needed to move this product.

9. Place the Safe on correct surface. Only use
this Safe on a stable, level, clean and dry
surface that is capable of sustaining the load.

7. Do not store Keys inside of the Safe.

Place your emergency keys in a location
outside of the safe making sure they are
in a secure location that you can find.

8. Warning: The brass components of this
product contain lead, a chemical known to
the State of California to cause birth defects
(or other reproductive harm). (California
Health & Safety code § 25249.5, et seq.)

9. The warnings, cautions, and instructions discussed
in this instruction manual cannot cover all possible
conditions and situations that may occur. It must
be understood by the operator that common sense
and caution are factors which cannot be built into
this product, but must be supplied by the operator.

10. The Safe is not fireproof.

NOTE: Harbor Freight Tools is not responsible
for the loss of any property stored within this safe
due to theft, fire, or any other circumstance.

Page 2 For technical questions, please call 1-800-444-3353. Item 95824

Installation Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document
including all text under subheadings therein before set up or use of this product.

1. The Safe MUST be bolted to a wall or
a floor to deter theft and prevent tipping.
There are mounting holes in the back wall and
bottom of the safe. See Figure A below.

Mounting

Holes

Figure A: Rear Mounting Hole Locations

2. Use Anchor Bolts, or seek a bonded professional
for installation of the Safe into cement.

Note: For floor or wall mounting, use bolts of a suitable
size (not included) to bolt into wall studs or floor joists.

3. Using the back of or bottom of the Safe as a
template, mark the location of the mounting holes on
the concrete surface using a pencil or other marker.

4. Move the Safe aside, and drill four suitable pilot
holes in the mounting surface. Make certain that
the drilling path is clear and free of obstacles such
as wires, cables and electrical lines. Drill holes
should be the diameter of the Anchor Bolt sleeves.

5. Insert the Anchor Bolts into each drilled hole and
tap Bolts into concrete. Remove washer and nut
from each bolt. The Safe now has to be lifted into
position to fit over the four anchor bolts. Because of
the heavy weight of the Safe, this task should only
be done by several capable workmen. With the
Safe in position, add washers and nuts to Anchor
Bolts. By tightening the nuts in place, the sleeve
around each bolt will expand, and secure each bolt
into the concrete to secure the Safe in place.

Shelf Installation

The safe comes with three shelves and 12 Shelf mounting clips. Place the clip into the shelf
mounting rails, then place the shelf onto the clips. Be sure you use four clips per each shelf.

Page 3For technical questions, please call 1-800-444-3353.Item 95824