Harbor Freight Tools 62116 Product manual
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual
near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and
the receipt in a safe and dry place for future reference.
3 Ton Floor Jack
®
with Rapid Pump
Item 62116
Weight Capacity 3 Tons (6,000 lb.)
Maximum Height 17 3/4"
Minimum Height 4-3/4"
Meets 2005 ANSI/ASME PALD standards.
REV 14a
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 2014 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Email our technical support at: productsupport@harborfreight.com
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Table of Contents
Safety ......................................................... 2
Setup .......................................................... 4
Operation .................................................... 5
SAFETY OPERATION MAINTENANCESETUP
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Maintenance ............................................... 5
Parts List and Diagram ............................... 7
Warranty .................................................... 12
WARNING SYMBOLS AND DEFINITIONS
Obey all safety messages that follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
Page 2 For technical questions, please call 1-888-866-5797. Item 62116
IMPORTANT SAFETY INFORMATION
Failure to heed these markings may result in personal injury and/or property damage.
1. Study, understand, and follow all instructions
before operating this device.
2. Do not exceed rated capacity.
3. Use only on hard, level surfaces.
4. Lifting device only. Immediately after lifting,
support the vehicle with appropriate means.
5. Do not move or dolly the vehicle while on the jack.
6. No alterations shall be made to this product.
7. Never work on, under or around a load
supported only by this device.
8. Do not adjust safety valve.
9. Wear ANSI-approved safety goggles and
heavy-duty work gloves during use.
10. Keep clear of load while lifting and lowering.
11. Lower load slowly.
12. Apply parking brake and chock
tires before lifting vehicle.
13. Lift vehicle only at manufacturer
recommended locations.
14. Inspect before every use; do not use
if parts are loose or damaged.
15. Do not use for aircraft purposes.
16. The warnings, precautions, and instructions
discussed in this manual cannot cover all
possible conditions and situations that may occur.
The operator must understand that common sense
and caution are factors, which cannot be built into
this product, but must be supplied by the operator.
17. The brass components of this product contain lead,
a chemical known to the State of California to cause
cancer, birth defects (or other reproductive harm).
(California Health & Safety code § 25249.5, et seq.)
IMPORTANT! Before first use:
Check hydraulic fluid level and fill to 1/4″ below the
fill port as needed - see instructions on page 5.
Thoroughly test the Jack for proper operation. If it
does not work properly, bleed air from its hydraulic
system - see instructions on page 5.
SAFETYOPERATIONMAINTENANCE SETUP
SAVE THESE INSTRUCTIONS.
Page 3For technical questions, please call 1-888-866-5797.Item 62116
Setup - Before Use:
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
SAFETY OPERATION MAINTENANCESETUP
Note: For additional information regarding the parts listed in the following pages,
refer to Parts List and Assembly Diagram on page 7.
Tool Set Up
Attaching the Handle
1. Attach the Upper Handle to the Lower Handle.
2. Loosen the Set Screw and insert the
assembled Handle into the Handle Socket.
Functions
Saddle
Grease
Fitting
(not
shown)
3. Tighten the Set Screw.
Cover
Plate
Handle
Handle
Socket
Fill Plug
DO NOT OPEN
Hydraulic
Unit
Safety Valve
Cover
OR ADJUST
Set
Screw
U-Joint
(not shown)
U-Joint
Page 4 For technical questions, please call 1-888-866-5797. Item 62116
Loading...