Harbor Freight Tools 61917 Product manual

Page 1
Page 2
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that
follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
IMPORTANT SAFETY INFORMATION
Failure to heed these markings may result in personal injury and/or property damage:
1. Study, understand, and follow all instructions before operating this device.
2. Do not exceed rated capacity.
3. Use only on hard, level surface.
4. Before moving a load, assure that the load is centered and secured with a load restraint device.
5. No alterations shall be made to this product.
6. Wear ANSI-approved safety goggles and heavy-duty work gloves during use.
7. Keep clear of load’s path while placing on and removing from dollies, and while moving.
8. Use as intended only. Do not use for aircraft purposes. Use only in pairs.
9. Inspect before every use; do not use if parts are loose or damaged.
10. Be aware of dynamic loading! Sudden load movement may briefly create excess load causing product failure.
11. Assemble only according to these instructions. Improper assembly can create hazards.
12. Keep your work area clean and well lit. Cluttered work areas invite accidents.
13. Keep bystanders, children, and visitors away while operating Wheel Dolly. Distractions can cause you to lose control.
14. Stay alert. Watch what you are doing, and use common sense when operating Wheel Dollies. Do not use while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating Wheel Dollies may result in serious personal injury.
15. Before use, read manufacturer’s instruction manual for the vehicle you will lift.
16. Keep clear of load while lifting and lowering.
17. Do not work under vehicle while on Dollies.
18. Lower load slowly.
19. Weight capacity and other product capabilities apply to properly and completely assembled product only.
20. Store idle Wheel Dollies out of reach of children and other untrained persons. Jacks are dangerous in the hands of untrained users.
21. Wheel Dolly service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury.
22. When servicing a Wheel Dolly, use only identical replacement parts - refer to attached, product-specific parts list and diagram. Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of injury and may void any applicable warranty.
23. Industrial applications must follow OSHA requirements.
Page 2 For technical questions, please call 1-888-866-5797. Item 61917
Page 3
24. Do not allow anyone in the vehicle while using the Wheel Dolly. Do not start the vehicle while it is on Wheel Dollies. Keep all bystanders a safe distance away from the vehicle.
26. Maintain product labels and nameplates. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement.
25. This product is not a toy. Do not allow children to play with or near this item.
SAVE THESE INSTRUCTIONS.
27. The warnings, precautions, and instructions discussed in this manual cannot cover all possible conditions and situations that may occur. The operator must understand that common sense and caution are factors, which cannot be built into this product, but must be supplied by the operator.
Specifications
Rated Capacity 1250 lb
Maximum Tire Width 9″
Page 3For technical questions, please call 1-888-866-5797.Item 61917
Page 4
Setup - Before Use:
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.
Note: For additional information regarding the parts listed in the following pages,
refer to Parts List and Assembly Diagram on page 6.
Functions
Left
Arm
Roller
Right
Arm
Foot
Pedal
Roller
Pedal
Lock
Lever
Handle
Figure A
Assembly Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product.
1. Assemble on a flat, level, hard and smooth surface.
2. Attach Casters, making sure the Square Nuts seat inside the Square Openings.
3. Thread Lock Nuts on to Caster bolts, securing tightly.
Square
Opening
Square
Nut
Lock
Nut
Caster
Figure B
Page 4 For technical questions, please call 1-888-866-5797. Item 61917
Page 5
Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.
1. Release the Foot Pedal by depressing it and disengaging the Pedal Lock.
2. Lifting Tire:
a. With the Lever in the down position, roll Dolly in
front of tire, spread Arms apart, then push Dolly forward so that Rollers are on either side of tire.
Figure C: Putting Dolly Around Tire
(Lever in Down Position)
b. Move the Lever to the up position, then pump the
Foot Pedal until the tire is just lifted off the ground.
Figure D: Lever in Up Position
WARNING! Be ready for any movement the vehicle may make when the other tire(s) come off the ground. Ensure that you have sufficient assistance and manpower to safely guide and control the vehicle.
3. Repeat 2. Lifting Tire: for the other tire(s). Use only in pairs.
WARNING! Stay clear of any sloping areas or entry ramps, however shallow they may appear. Sufficient space should be allowed between the side of the vehicle and an adjacent wall for the vehicle to be withdrawn from its location in a sideways manner.
4. Lowering Tire:
a. Move the Lever to the down position, then
depress and release the Foot Pedal.
b. Once tire is on the ground, spread
Arms and remove Dolly.
c. Push arms together, then depress Foot Pedal
all the way and secure with Pedal Lock.
Inspection, Maintenance, And Cleaning
Procedures not specifically explained in this manual must be performed only by a qualified technician.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use.
1. BEFORE EACH USE, inspect the general condition of the Wheel Dolly. Check for:
• broken, cracked, or bent parts,
• loose or missing parts,
• and any condition that may affect the proper operation of the product.
2. AFTER EVERY USE, wipe with a clean cloth. Then, store the Wheel Dolly in a safe, dry location out of reach of children and other non-authorized people.
3. PERIODICALLY:
• lubricate the Casters and
• put Lever in down position, spread arms
Foot Pedal pivot with oil.
apart and lightly grease the notched tube.
Page 5For technical questions, please call 1-888-866-5797.Item 61917
Page 6
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Parts List and Assembly Diagram
Parts List
Part Description Qty
1 Roller 2 2 Screw (4.2x25) 4 3 Roller Bearing 4 4 Lock Nut (M12) 4 5 Caster 4 6 Right Arm 2 7 Lock Nut (M6) 1 8 Rubber Ring 1
9 Pedal Lock 1 10 Retaining Pin 2 1 11 Square Plug 1 12 Pedal 1 13 Front Pawl 1
Part Description Qty
14 Spring 1 15 Lever 1 16 Spring Pad 1 17 Screw (M8x22) 1 18 Back Pawl 1 19 Spring 1 20 Plate 1 21 Retainer 1 22 Retaining Pin 1 1 23 Cotter Pin (Ø3x30) 1 24 Washer 2 25 Torsion Spring 1 26 Left Arm 1
Record Serial Number Here:
Note: If product has no serial number, record
month and year of purchase instead.
Page 6 For technical questions, please call 1-888-866-5797. Item 61917
Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.
Page 7
Assembly Diagram
Page 7For technical questions, please call 1-888-866-5797.Item 61917
Page 8
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797
Loading...