Harbor Freight Tools 61748 Product manual

Table of Contents

Safety ......................................................... 3

Specifications ............................................. 7

Setup .......................................................... 8

SAFETY OPERATION MAINTENANCESETUP

Operation ................................................... 10

Maintenance .............................................. 12

Parts List and Diagram .............................. 14

Warranty .................................................... 16

WARNING SYMBOLS AND DEFINITIONS

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that

follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

Addresses practices not related to personal injury.

Page 2 For technical questions, please call 1-888-866-5797. Item 61748

IMPORTANT SAFETY INFORMATION

General Tool Safety Warnings

Read all safety warnings and instructions.

Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

1. KEEP GUARDS IN PLACE and in working order.

2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are
removed from tool before turning it on.

3. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite accidents.

4. DON’T USE IN DANGEROUS ENVIRONMENT.
Don’t use power tools in damp or wet locations,
or expose them to rain. Keep work area well lighted.

5. KEEP CHILDREN AWAY. All visitors should
be kept safe distance from work area.

6. MAKE WORKSHOP KID PROOF with padlocks,
master switches, or by removing starter keys.

7. DON’T FORCE TOOL. It will do the job better
and safer at the rate for which it was designed.

8. USE RIGHT TOOL. Don’t force tool or attachment
to do a job for which it was not designed.

Table A: RECOMMENDED MINIMUM WIRE GAUGE

FOR EXTENSION CORDS

(120 VOLT)

NAMEPLATE

AMPERES

(at full load)

0 – 6 18 16 16 14

6.1 – 10 18 16 14 12

10.1 – 12 16 16 14 12

12.1 – 16 14 12 Do not use.

9. USE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. When using
an extension cord, be sure to use one heavy
enough to carry the current your product will draw.
An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating.
Table A shows the correct size to use depending
on cord length and nameplate ampere rating.
If in doubt, use the next heavier gauge.
The smaller the gauge number, the heavier the cord.

EXTENSION CORD

LENGTH

25′ 50′ 100′ 150′

10. WEAR PROPER APPAREL. Do not wear
loose clothing, neckties, rings, bracelets, or
other jewelry which may get caught in moving
parts. Nonslip footwear is recommended.
Wear protective hair covering to contain long hair.

11. ALWAYS USE SAFETY GLASSES. Also use
face or dust mask if cutting operation is dusty.
Everyday eyeglasses only have impact resistant
lenses, they are NOT safety glasses.

12. SECURE WORK. Use clamps or a vise to
hold work when practical. It’s safer than using your
hand and it frees both hands to operate tool.

13. DON’T OVERREACH.
Keep proper footing and balance at all times.

14. MAINTAIN TOOLS WITH CARE.
Keep tools sharp and clean for best and
safest performance. Follow instructions for
lubricating and changing accessories.

15. DISCONNECT TOOLS before servicing;
when changing accessories, such as
blades, bits, cutters, and the like.

16. REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure switch is in
off position before plugging in.

17. USE RECOMMENDED ACCESSORIES.
Consult the owner’s manual for recommended
accessories. The use of improper accessories
may cause risk of injury to persons.

18. NEVER STAND ON TOOL.
Serious injury could occur if the tool is tipped or
if the cutting tool is unintentionally contacted.

19. CHECK DAMAGED PARTS. Before further use
of the tool, a guard or other part that is damaged
should be carefully checked to determine that
it will operate properly and perform its intended
function – check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting, and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or replaced.

20. DIRECTION OF FEED.
Feed work into a blade or cutter against the
direction of rotation of the blade or cutter only.

SAFETYOPERATIONMAINTENANCE SETUP

21. NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN POWER OFF.

Page 3For technical questions, please call 1-888-866-5797.Item 61748

Grounding Instructions

SAFETY OPERATION MAINTENANCESETUP

TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT
GROUNDING WIRE CONNECTION READ AND FOLLOW THESE INSTRUCTIONS:

110-120 V~ Grounded Tools: Tools with Three Prong Plugs

1. In the event of a malfunction or breakdown,
grounding provides a path of least resistance for
electric current to reduce the risk of electric shock.
This tool is equipped with an electric cord having an
equipment-grounding conductor and a grounding
plug. The plug must be plugged into a matching
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.

2. Do not modify the plug provided – if it will
not fit the outlet, have the proper outlet
installed by a qualified electrician.

3. Improper connection of the equipment-grounding
conductor can result in a risk of electric shock.
The conductor with insulation having an outer
surface that is green with or without yellow
stripes is the equipment-grounding conductor.
If repair or replacement of the electric cord or
plug is necessary, do not connect the equipment­grounding conductor to a live terminal.

4. Check with a qualified electrician or service
personnel if the grounding instructions are
not completely understood, or if in doubt as
to whether the tool is properly grounded.

5. Use only 3-wire extension cords that
have 3-prong grounding plugs and 3-pole
receptacles that accept the tool’s plug.

6. Repair or replace damaged or
worn cord immediately.

Grounding

Pin

125 V~ 3-Prong Plug and Outlet

(for up to 125 V~ and up to 15 A)

7. This tool is intended for use on a circuit that has
an outlet that looks like the one illustrated above
in 125 V~ 3-Prong Plug and Outlet. The tool has
a grounding plug that looks like the plug illustrated
above in 125 V~ 3-Prong Plug and Outlet.

8. The outlet must be properly installed and grounded
in accordance with all codes and ordinances.

9. Do not use an adapter to connect
this tool to a different outlet.

Page 4 For technical questions, please call 1-888-866-5797. Item 61748

Grinder Safety Warnings

For Your Own Safety Read Instruction Manual

Before Operating Grinder

1. Wear eye protection.

2. Use grinding wheel suitable for speed of grinder.

3. Replace cracked wheel immediately.

4. Always use guards and eye shields.

5. Do not overtighten wheel nut.

6. Use only flanges furnished with the grinder.

7. Adjust distance between wheel and work rest to
maintain 0.0625 inch or less separation as the
diameter of the wheel decreases with use.

8. Frequently clean grinding dust from beneath grinder.

9. Wear a full face shield over ANSI-approved
safety goggles during use.

10. Do not grind with side of wheel unless wheel is
specifically designed for that type of grinding.

11. DO NOT OPERATE WITH ANY GUARD

DISABLED, DAMAGED, OR REMOVED. Moving
guards must move freely and close instantly.

12. The use of accessories or attachments not
recommended by the manufacturer may
result in a risk of injury to persons.

13. When servicing use only identical replacement parts.

16. Industrial applications must follow OSHA guidelines.

17. Maintain labels and nameplates on the tool.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.

18. Avoid unintentional starting.
Prepare to begin work before turning on the tool.

19. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.

20. WARNING: Some dust created by power
sanding, sawing, grinding, drilling, and other
construction activities, contains chemicals
known [to the State of California] to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:

• Lead from lead-based paints

• Crystalline silica from bricks and cement or other
masonry products

• Arsenic and chromium from
chemically treated lumber
Your risk from these exposures varies,
depending on how often you do this type of work.
To reduce your exposure to these chemicals:
work in a well ventilated area, and
work with approved safety equipment, such
as those dust masks that are specially
designed to filter out microscopic particles.
(California Health & Safety Code § 25249.5, et seq.)

SAFETYOPERATIONMAINTENANCE SETUP

14. Only use safety equipment that has been approved
by an appropriate standards agency. Unapproved
safety equipment may not provide adequate
protection. Eye protection must be ANSI-approved
and breathing protection must be NIOSH-approved
for the specific hazards in the work area.

15. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication.
A moment of inattention while operating power
tools may result in serious personal injury.

21. WARNING: Handling the cord on this product will
expose you to lead, a chemical known to the State
of California to cause cancer, and birth defects or
other reproductive harm. Wash hands after handling.
(California Health & Safety Code § 25249.5, et seq.)

22. The warnings, precautions, and instructions
discussed in this instruction manual cannot cover all
possible conditions and situations that may occur.
It must be understood by the operator that
common sense and caution are factors
which cannot be built into this product,
but must be supplied by the operator.

Page 5For technical questions, please call 1-888-866-5797.Item 61748

Vibration Safety

This tool vibrates during use. Repeated or long-term exposure to vibration may cause temporary or permanent
physical injury, particularly to the hands, arms and shoulders. To reduce the risk of vibration-related injury:

1. Anyone using vibrating tools regularly or for an

SAFETY OPERATION MAINTENANCESETUP

extended period should first be examined by a
doctor and then have regular medical check-ups
to ensure medical problems are not being caused
or worsened from use. Pregnant women or
people who have impaired blood circulation to
the hand, past hand injuries, nervous system
disorders, diabetes, or Raynaud’s Disease should
not use this tool. If you feel any medical or
physical symptoms related to vibration (such as
tingling, numbness, and white or blue fingers),
seek medical advice as soon as possible.

SAVE THESE INSTRUCTIONS.

2. Do not smoke during use. Nicotine reduces
the blood supply to the hands and fingers,
increasing the risk of vibration-related injury.

3. Use tools with the lowest vibration when there
is a choice between different processes.

4. Include vibration-free periods each day of work.

5. Grip tool as lightly as possible (while still keeping
safe control of it). Let the tool do the work.

6. To reduce vibration, maintain the tool as
explained in this manual. If any abnormal
vibration occurs, stop use immediately.

Page 6 For technical questions, please call 1-888-866-5797. Item 61748

Specifications

Electrical Rating 120V~ / 60Hz / 2.1A

No Load Speed 3450 RPM

Max. Wheel Size Ø6″ (150mm) x 3/4″ Thick x 1/2″ Arbor

Arbor Size 1/2″

Base Size 5-1/2″ x 6-1/3″

Mounting Holes Two 3/8″

Work Light Bulb 40 W Household type

3168328

SAFETYOPERATIONMAINTENANCE SETUP

Page 7For technical questions, please call 1-888-866-5797.Item 61748

Setup - Before Use:

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.

SAFETY OPERATION MAINTENANCESETUP

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn the Power Switch of the tool off and unplug the tool from its electrical outlet
before performing any procedure in this section.

Note: For additional information regarding the parts listed in the following pages,

refer to the Assembly Diagram near the end of this manual.

Assembly/Mounting

1. Install Right Work Rest (38) to the
Right Wheel Guard (37).
Use Knob (6), Screw (18), and Nut (8)
to secure it in place as shown in Figure A.

Right Wheel

Guard (37)

Right

Work

Rest (38)

Screw (18)

Knob (6)

Nut (8)

Figure A: Work Rest Installation

2. Install Left Work Rest (7) to the Left Wheel Guard (9)
using Knob (6), Screw (18), and Nut (8).

3. Adjust the Work Rests to within 1/16″ of the
Grinding Wheel. To adjust this distance,
loosen Knobs (6) and move Work Rests (7,38).

Right Shield

Arm (44)

Bolt (1)

Washer (2,3)

Figure B: Spark Guard and

Right Shield Arm Installation

5. Attach Right Shield Arm (44) to the
Right Wheel Guard (37) using Bolt (1)
and Washers (2,3), see Figure B.

6. Attach Left Shield Arm (4) to
the Left Wheel Guard (9) using
Bolt (1) and Washers (2,3).

7. Attach right Eye Shield (43) to Right Shield Arm (44)
using Knob (48) as shown in Figure C.

8. Attach left Eye Shield (5) to
Left Shield Arm (4) using Knob (48).

Knob

(48)

Spark

Guard (12)

Screw (11)

4. Attach a Spark Guard (12) to each
Wheel Guard (37,9) using a Screw (11) as shown
in Figure B. Adjust each Spark Guard (12) to

within 1/16” (0.0625″) of the Grinding Wheel

and tighten each Screw (12).

Page 8 For technical questions, please call 1-888-866-5797. Item 61748

Right

Shield

Arm (44)

Figure C: Right Eye Shield Installation

Eye

Shield

(43)

Functions

Light

Switch

SAFETYOPERATIONMAINTENANCE SETUP

Spark

Guard

Eye

Shield

Grinding

Wheel

Work

Rest

Spark

Guard

Eye

Shield

Grinding

Wheel

Work

Rest

Power

Switch

Page 9For technical questions, please call 1-888-866-5797.Item 61748

Operating Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.

SAFETY OPERATION MAINTENANCESETUP

Tool Set Up

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn the Power Switch of the tool off and unplug the tool from its electrical outlet
before performing any procedure in this section.

TO PREVENT SERIOUS INJURY:
DO NOT OPERATE WITH ANY GUARD DISABLED, DAMAGED, OR REMOVED.
Moving guards must move freely and close instantly.

Changing a Grinding Wheel

1. The Grinding Wheel MUST be:

• rated to at least 3450 RPM.

• no larger than 6″ (150mm) in diameter.

• fitted with a 1/2″ or 5/8″ round arbor hole.

• 3/4″ thick.

• suitable for edge grinding, not surface grinding.

• dry and clean.

• proven undamaged by inspection and
by the ring-test explained below.

2. Remove the three Screws (18) that
hold on the Wheel Cover (17,35).

3. Hold opposite wheel to hold the Spindle (42) in
place while loosening the Hex Nut (16/34).

NOTICE: Nut (3) has left-handed threads
and loosens clockwise.

4. Remove the outer Flange (14).
Keep the inner Flange (14) in
position on the Spindle.

5. Closely inspect the wheel before mounting.
Perform a ring-test on the wheel (unless wheel is

smaller than 4″ or is an unusual shape) as follows:

a. Suspend wheel using a dowel or

finger through the arbor hole.

b. Tap the flat side of the wheel with a light

non-metallic object, such as a screwdriver
handle, at a point 45° from the vertical center
line on each side of the wheel and 1 – 2 inches
from the edge of the wheel (see Illustration).

c. Rotate the wheel 90° and repeat the test

until the entire wheel has been checked.

d. An undamaged wheel will

give a clear tone. If cracked, there will be
a dead sound and not a clear ring.

Hang

Wheel

from

Dowel

V
E
R
T

I
C
A
L

Tap

Wheel

45° 45°

Here

C
E
N
T
E
R

45° 45°

Figure D: Ring Test

6. For wheels with paper gaskets (blotters) or
metal gaskets: Slip the Grinding Wheel onto the
Spindle with the gasket first. The gasket should be
centered on the Grinding Wheel and the Wheel and
gasket should rest flat against the inner Flange.

WARNING: To prevent serious injury, gaskets
must be used for all grinding wheels they are
provided with. Gaskets help prevent grinding
wheel damage and wheel slippage,
causes of wheel failure.

7. Place the outer flange onto the Spindle.
Thread the Nut (16/34) onto the Spindle.

NOTICE: Nut (3) has left-handed threads
and tightens counterclockwise.

Wrench tighten only enough so that the Wheel is
securely held on the Spindle.

WARNING: To prevent serious injury,
do not overtighten Nut. Overtightening can
damage the wheel, causing wheel failure.

Page 10 For technical questions, please call 1-888-866-5797. Item 61748

Workpiece and Work Area Set Up

1. Designate a work area that is clean and well-lit.
The work area must not allow access by children
or pets to prevent distraction and injury.

General Operating Instructions

1. Make sure that the Switch is in the off-position,
then plug in the tool.

2. Turn on the tool.

3. Allow the tool to come up to full speed
before touching the wheel.

2. Route the power cord along a safe route to reach
the work area without creating a tripping hazard or
exposing the power cord to possible damage. The
power cord must reach the work area with enough
extra length to allow free movement while working.

3. There must not be objects, such as utility lines,
nearby that will present a hazard while working.

SAFETYOPERATIONMAINTENANCE SETUP

5. To create a smoother surface,
keep the workpiece moving over the wheel.

6. To prevent accidents, turn off the tool and
disconnect its power supply after use. Clean, then
store the tool indoors out of children’s reach.

4. Apply the workpiece to the wheel,
allowing the tool to operate at full speed.
If the tool bogs down, use lighter pressure.

Page 11For technical questions, please call 1-888-866-5797.Item 61748

Maintenance and Servicing

Procedures not specifically explained in this manual must

be performed only by a qualified technician.

SAFETY OPERATION MAINTENANCESETUP

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn the Power Switch of the tool off and unplug the tool from its electrical outlet
before performing any procedure in this section.

TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:
Do not use damaged equipment. If abnormal noise or vibration
occurs, have the problem corrected before further use.

Cleaning, Maintenance, and Lubrication

1. BEFORE EACH USE, inspect the general
condition of the tool. Check for:

• loose hardware,

• misalignment or binding of moving parts,

• cracked or broken parts,

• damaged electrical wiring, and

• any other condition that may

affect its safe operation.

2. AFTER USE, wipe external surfaces
of the tool with clean cloth.

Accessory Storage and Handling

1. Handle accessories carefully to prevent
dropping or bumping. Do not use wheels
that have been dropped or bumped.

3. Periodically, wear ANSI-approved
safety goggles and NIOSH-approved
breathing protection and blow dust and grit out
of the motor vents using dry compressed air.

4. Bulb Replacement -
Allow bulb to cool completely before replacing it.
Replace it only with a 40 W or
smaller household bulb.

5.

2. Store accessories in shelves, racks, boxes, or

WARNING! If the supply cord of this
power tool is damaged, it must be replaced
only by a qualified service technician.

drawers. Keep storage area dry and above
freezing. Any grinding or cut-off wheels exposed to
humidity or freezing temperatures must not be used.

Page 12 For technical questions, please call 1-888-866-5797. Item 61748

Troubleshooting

Problem Possible Causes Likely Solutions

Tool will not start. 1. Cord not connected.

2. No power at outlet.

3. Tool’s thermal reset breaker
tripped (if equipped).

4. Internal damage or wear. (Carbon
brushes or switch, for example.)

Tool operates
slowly.

Performance
decreases
over time.

Excessive noise
or rattling.

Overheating. 1. Forcing machine to work too fast.

Extension cord too long or
wire size too small.

1. Accessory dull or damaged.

2. Carbon brushes worn or damaged.

1. Internal damage or wear. (Carbon
brushes or bearings, for example.)

2. Accessory dull or damaged.

3. Blocked motor housing vents.

4. Motor being strained by long or
small diameter extension cord.

1. Check that cord is plugged in.

2. Check power at outlet. If outlet is unpowered,
turn off tool and check circuit breaker.
If breaker is tripped, make sure circuit is right
capacity for tool and circuit has no other loads.

3. Turn off tool and allow to cool.
Press reset button on tool.

4. Have technician service tool.

Eliminate use of extension cord. If an extension cord
is needed, use one with the proper diameter for its
length and load. See Table A on page 3.

1. Keep cutting accessories sharp.
Replace as needed.

2. Have qualified technician replace brushes.

1. Have technician service tool.

1. Allow machine to work at its own rate.

2. Keep cutting accessories sharp.
Replace as needed.

3. Wear ANSI-approved safety goggles and
NIOSH-approved dust mask/respirator while
blowing dust out of motor using compressed air.

4. Eliminate use of extension cord.
If an extension cord is needed, use one with
the proper diameter for its length and load.
See Table A on page 3.

SAFETYOPERATIONMAINTENANCE SETUP

Follow all safety precautions whenever diagnosing or servicing
the tool. Disconnect power supply before service.

Page 13For technical questions, please call 1-888-866-5797.Item 61748

Parts List and Diagram

PLEASE READ THE FOLLOWING CAREFULLY

SAFETY OPERATION MAINTENANCESETUP

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Parts List

Part Description Qty

1 Hex Bolt 2
2 Spring Washer 2
3 Flat Washer 2
4 Left Shield Arm 1
5 Left Eye Shield 1
6 Knob 2
7 Left Work Rest 1
8 Nut 6

9 Left Wheel Guard 1
10 Carriage Bolt 2
11 Screw 2
12 Spark Guard 2
13 Philips Screw+Spring Washer 6
14 Flange 4
15 Grinding Wheel 150×20×12.7 1
16 Hex Nut 1
17 Left Wheel Cover 1
18 Screw 6
19 Hex Flange Nut 4
20 End Bell 2
21 Wavy washer 1
22 Stator 1
23 Cord Bushing 1
24 Toothed Washer 1
25 Philips Screw+Flat

2

Washer+Spring Washer

Part Description Qty

26 Switch 1
27 Switch Plate 1
28 Philips Screw+Spring Washer 2
29 Bottom Plate 1
30 Philips Screw+Flat Washer 2
31 Rubber Foot 4
32 Capacitor 1
33 Flat Washer 1
34 Hex Nut 1
35 Right Wheel Cover 1
36 Grinding Wheel 150×20×12.7 1
37 Right Wheel Guard 1
38 Right Work Rest 1
39 Philips Screw+Flat Washer 4
40 Bearing 2
41 Cord Bushing 1
42 Spindle 1
43 Right Eye Shield 1
44 Right Shield Arm 1
45 Power Cord 1
46 Base 1
47 Work Lamp 1
48 Eyeshield Locking Knob 2
49 Lamp Locking Nut 1

Record Product’s Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only,

and are not available individually as replacement parts.

Page 14 For technical questions, please call 1-888-866-5797. Item 61748

Assembly Diagram

SAFETYOPERATIONMAINTENANCE SETUP

Page 15For technical questions, please call 1-888-866-5797.Item 61748

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797