Harbor Freight Tools 41876 User Manual

PORTABLE THREADING

®

MACHINE

41876

ASSEMBLY & OPERATING INSTRUCTIONS

Due to continuing improvements, actual product may differ slightly from the product described herein.

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at http://www.harborfreight.com

TO PREVENT SERIOUS INJURY,

READ AND UNDERSTAND ALL WARNINGS

AND INSTRUCTIONS BEFORE USE.

Copyright©1999 by Harbor Freight Tools® . All rights reserved. No portion of this manual or any
artwork contained herein may be reproduced in any shape or form without the express written
consent of Harbor Freight Tools.

For technical questions and replacement parts, please call 1-800-444-3353.

THANK YOU for choosing a HARBOR FREIGHT TOOLS product. For future reference, please complete the
owner’s record below:

Model____________ Serial No._____________ Purchase Date_______________

SAVE THE RECEIPT, WARRANTY AND THESE INSTRUCTIONS. It is important that you read the entire
manual to become familiar with the unit BEFORE you begin assembly.

Technical Specifications

Electrical Requirements: 110V, 12 Amp, 60 Hz
Die Sizes: 1/2", 3/4", 1", 1-1/4"
Plug, Cord and Switch: UL Listed
Overall Dimensions: 24" x 7-1/2" x 3-1/4"
Weight: 12.5 Lbs.
Accessories Included: Oil Can, Side Handle, Cast Iron Clamp, Blow Mold Carrying Case

Warning: The warnings, cautions and instructions discussed in this instruction manual

cannot cover all possible conditions and situations that may occur. It must
be understood by the operator that COMMON SENSE AND CAUTION ARE
FACTORS WHICH CANNOT BE BUILT INTO THIS PRODUCT, BUT
MUST BE SUPPLIED BY THE OPERATOR.

The Operator

PLEASE REMEMBER:

Do not operate the product if under the influence of alcohol or drugs. Read warning labels on prescriptions to
determine if your judgment/reflexes might be impaired.

Do not wear loose clothing or jewelry as they can be caught in moving parts.

Protective gloves and non-skid footwear are recommended.

Wear restrictive hair covering to contain long hair.

Use eye and ear protection. Always wear ANSI approved impact safety goggles.

Maintain proper footing and balance at all times.

Do not abuse the power cord. Do not yank on cord to disconnect it from outlet. Keep the cord away from heat,
oil and sharp edges.

Avoid unintentional starting. Do not carry any tool with your finger on the trigger.

REV 12/05

SKU 41876 For technical questions, please call 1-800-444-3353. Page 2

Work Area

TO AVOID RISK OF PERSONAL INJURY, EQUIPMENT DAMAGE, FIRE AND SHOCK, MAKE SURE YOUR
WORK AREA IS:

Free of damp, wet or rainy conditions.

Free of flammable gasses or liquids.

Free of children (never let them handle tools or machinery).

Well-lit.

Clean and uncluttered.

Well-ventilated.

Before Operating

Before operating your Portable Threading Machine check for damaged parts.

DO NOT exceed the maximum capacity of the tool.

Never force the tool or attachment to do the work of a larger industrial tool. It is designed to do the job better
and more safely at the rate for which it was intended.

Do not try to use inappropriate attachments in an attempt to exceed the tool’s capacity. Approved accessories
are available from Harbor Freight Tools.

Check for damaged parts. Before using any tool, any part that appears damaged should be carefully checked
to determine that it will operate properly and perform its intended function.

Make sure all clamps, locks and bolts are tight.

Make certain to turn off and unplug the Portable Threading Machine when loading or when doing any
maintenance. The tool should always be turned off and unplugged when not in use.

Do not reach over or across running machines.

Note: Performance of this tool may vary depending on variations in local line voltage. Extension cord usage
may also affect tool performance.

SKU 41876 For technical questions, please call 1-800-444-3353. Page 3