Harbor Freight Tools 41711 User Manual
3 in 1 Heavy Duty
Tile Cutter
Model
41711 41711
41711
41711 41711
Assembly & Operating Instructions
www.HarborFreight.com
Copyright 2000 by Harbor Freight Tools. All Rights Reserved.
No portion of this manual or any artwork contained herein may be reproduced in any
manner, shape or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353.
SPECIFICATIONS MODEL # 4171 1 TILE CUTTER
Base Material: Steel Plate, 13 ga.
Base Size: 7-3/4”W x 27-1/2”L
Guide Support: Cast Aluminum
Guide Bars: 3/4” Steel T ube
Guide Bar Length: 25-1/2”
Cutter Fixture:: Cast Aluminum (3 pcs.)
Straight Cutter Wheel: Hardened Steel
Straight Capacity: 15-3/4”
Cutter Handle: 1/2” Steel T ube x 12” L
Circle Cutter: Cast Aluminum
Circle Dimension: 1-3/16” Min, 3-1/4” Max.
Cutting Tip: Carbide
Miter and Fence: Cast Aluminum
Adjustment: 0O to 45O (5O increments)
Net W eight: 13.85 Lbs.
FEATURES OF THIS TOOL
1. Sturdy cast aluminum and steel construction will deliver a long service life.
2. Large capacity straight cuts up to 17” long and circles up to 3-1/4”.
3. Convenient built-in breaker .
4. Handy circle cutter will cut circles as small as 1-3/16” and as large as 3-1/4”.
5. Built in measurement scales for tile width, cut angle, and circle cut dimension.
SAVE THIS MANUAL
You will need this manual for the safety warnings and cautions, assembly instructions, operating
procedures, maintenance procedures, trouble shooting, parts list, and diagram. Keep your invoice
with this manual. Write the invoice number on the inside of the front cover. Keep both this manual
and your invoice in a safe, dry place for future reference.
NOTICE
The Warnings, Cautions, and Instructions discussed in this instruction manual cannot
cover all possible conditions and situations that may occur. It must be understood by
the operator that common sense and caution are factors which cannot be built into this
product, but must be supplied by the operator.
Page 2 SKU # 41711
SAFETY WARNING & CAUTIONS
WARNING: When using shop equipment, basic safety precautions should
always be followed to reduce the risk of personal injury and hazards.
READ ALL INSTRUCTIONS BEFORE USING THIS TOOL!
1. KEEP WORK AREA CLEAN. Cluttered areas invite injuries.
2. OBSER VE WORK AREA CONDITIONS. Do not use tools in damp, wet, or poorly lit locations.
Don’t expose to rain. Keep work area well lit. Do not use electrically powered equipment in the
presence of flammable gases or liquids.
3. KEEP CHILDREN A WA Y. Children must never be allowed in the work area. Do not let them
handle machines, tools, or equipment.
4. STORE IDLE EQUIPMENT . When not in use, tools must be locked up in a dry location to inhibit
rust. Always lock up tools and keep out of reach of children.
5. DO NOT FORCE THE TOOL. It will do the job better and more safely at the rate for which it
was intended. Do not use inappropriate attachments in an attempt to exceed the tool’ s capacities.
6. USE THE RIGHT TOOL FOR THE JOB. Do not use a tool for a purpose for which it was not
intended.
7. DRESS PROPERL Y. Do not wear loose clothing or jewelry , as they can be caught in moving
parts. Non-skid footwear is recommended. W ear restrictive hair covering to contain long hair .
Always wear appropriate work clothing.
8. USE EYE, EAR AND BREA THING PROTECTION. Always wear ANSI approved impact safety
goggles if you are producing metal filings or wood chips. W ear an ANSI approved dust mask or
respirator when working around metal, wood, and chemical dusts and mists. Use ANSI approved
ear protection when working in a loud or noisy environment.
9. DO NOT OVERREACH. Keep proper footing and balance at all times. Do not reach over or
across running machines.
10. MAINT AIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance.
Follow instructions for lubricating and changing accessories. Control handles must be kept clean,
dry , and free from oil and grease at all times.
Page 3 SKU # 41711
Loading...