Harbor Freight Tools 41453 User Manual

6” CUTOFF SAW

Model 41453

ASSEMBLY AND

OPERATING INFORMATION

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at http://www.harborfreight.com

manual or any artwork contained herein may be reproduced in any shape or form

without the express written consent of Harbor Freight Tools.

For technical questions please call 1-800-444-3353.

MANUAL REVISED 01/02

SPECIFICATIONS TABLE

metInoitpircseD

stnemeriuqeRlacirtcelE

)dedulcnItoN(leehWgnidnirGffO-tuC

retemaiDeldnipS )robrA"8/7tifotstpadae

snoisnemiDesaB"11x"61x"41

gninepOwaJesiV"8/1-3

)elacShtiw(paCleviwSesiVseergeD54-0

000,9muminiMMPR

gnalfretuo("8/5

,MPR000,9,spmA3.5,zH06,CAV511

gulPgnorP2htiwdroCdetsiLLU'6,eguaG61

,retemaiDmumixaM"6

thgieWsdnu

oP3.9

FOR USE WITH CUTOFF GRINDING WHEEL (SKU #42400)- NOT INCLUDED.

SAVE THIS MANUAL

You will need this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance, and cleaning procedures. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep this manual and invoice in a safe and dry place for future reference.

GENERAL SAFETY WARNINGS AND PRECAUTIONS

1. KEEP WORK AREA CLEAN AND DRY. Cluttered, damp or wet work areas

invite injuries.

2. KEEP CHILDREN AWAY FROM WORK AREA. Do not allow children to handle

this product.

3. STORE IDLE EQUIPMENT. When not in use, tools and equipment should be

stored in a dry location to inhibit rust. Always lock up tools and equipment and keep out of reach of children.

4. DO NOT USE THIS PRODUCT IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not attempt to use this product.

5. USE EYE, HEARING, AND BREATHING PROTECTION. Wear ANSI approved safety impact eyeglasses, hearing protectors, dust masks or respirator when using this product. ANSI approved safety impact eyeglasses, hearing protectors, dust masks and respirators are available from Harbor Freight Tools.

REV 12/04; 01/05

SKU 41453 For technical questions, please call 1-800-444-3353. PAGE 2

6. DRESS SAFELY. Nonskid footwear or safety shoes should be used when work- ing with this product. Do not wear loose clothing or jewelry as they can become caught in moving parts. Wear a protective hair covering to prevent long hair from becoming caught in moving parts. If wearing a long-sleeve shirt, roll sleeves up above elbows.

7. INDUSTRIAL APPLICATIONS MUST FOLLOW OSHA REQUIREMENTS.

8. DO NOT OVERREACH. Keep proper footing and balance at all times to prevent tripping, falling, back injury, etcetera.

9. STAY ALERT. Watch what you are doing at all times. Use common sense. Do not use this product when you are tired or distracted from the job at hand.

10. CHECK FOR DAMAGED PARTS. Before using this product, carefully check that it will operate properly and perform its intended function. Check for damaged parts and any other conditions that may affect the operation of this product. Replace or repair damaged or worn parts immediately.

11. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical replacement parts. Only use accessories intended for use with this product. Approved accessories are available from Harbor Freight Tools.

12. MAINTAIN THIS PRODUCT WITH CARE. Keep this tool clean and dry, and keep cutoff grinding wheels clean and sharp for better and safer performance.

13. MAINTENANCE: For your safety, service and maintenance should be performed regularly by a qualified technician.

14. USE THE RIGHT PRODUCT FOR THE RIGHT JOB. There are certain applications for which this product was designed. Do not use small equipment, tools or attachments to do the work of larger industrial equipment, tools or attachments. Do not use this product for a purpose for which it was not intended.

SPECIFIC PRODUCT WARNINGS AND PRECAUTIONS

1. DANGER! Do not use unapproved accessories. Do not use circular saw blades or wire brushes on this tool. Do not use any accessory except 6” Cut-Off Grinding Wheels rated at 9,000 RPMs or higher.

2. GUARD AGAINST ELECTRIC SHOCK. Do not submerge the Cut-Off Saw in water or other liquids. Always prevent body contact with grounded surfaces such as pipes, radiators, ranges, refrigerators, etcetera. Do not operate the Cut-Off Saw if the operator is standing in water.

SKU 41453 For technical questions, please call 1-800-444-3353. PAGE 3

To comply with the National Electric Code (NFPA70), and to provide additional protection from the risk of electrical shock, the Cut-Off Saw should only be connected to a

115 Volt, 3 prong, electrical outlet that is protected by a Ground

Fault Circuit Interrupter (GFCI).

3. ALWAYS USE A 3 PRONG PLUG ADAPTER (not provided). This Cut-Off Saw is equipped with a attach and use a

2 prong

3 prong

Power Cord Plug (31). For increase safety always

, grounded, Plug Adapter. (See Figure A, and Assy.

Diagram.)

2 PRONG PLUG (31)

FIGURE A

3 PRONG PLUG ADAPTER

115 VOLT OUTLET

4. MAKE SURE THE POWER SWITCH IS IN THE “OFF” POSITION BEFORE

PLUGGING IN THE POWER CORD.

5. DO NOT ABUSE THE POWER CORD. Do not use the Power Cord to pull the Plug from a power outlet. Keep Power Cord away from heat, oil, sharp edges, and moving parts. Replace a damaged Power Cord immediately. Route the Power Cord safely. Protect it from being damaged by other equipment in the work area. Do not route the Power Cord where it can be walked on or tripped over.

6. IF YOU USE AN EXTENSION CORD, MAKE SURE TO USE ONLY UL

APPROVED CORDS HAVING THE CORRECT GAUGE AND LENGTH. (SEE FIGURE B.)

REQUIRED EXTENSION CORD GAUGE

Nameplate Extension Cord Length

Amperes 25’ 50’ 75’ 100’ 150’ 200’

0 - 5 16 16 16 14 12 12

5.1 - 8 16 16 14 12 10 -

8.1 - 12 14 14 12 10 - -

12.1 - 15 12 12 10 10 - -

15.1 - 20 10 10 10 - - -

FIGURE B

SKU 41453 For technical questions, please call 1-800-444-3353. PAGE 4

+ 7 hidden pages