Harbor Freight Tools 40195 User Manual

Page 1
RECHARGEABLE -3 HEADED
®
SHAVER
40195
CHARGING AND OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
3491 Mission Oaks Blvd., Camarillo, CA 93011
TO PREVENT SERIOUS INJURY, READ AND UNDERSTAND
ALL WARNINGS AND INSTRUCTIONS BEFORE USE.
Copyright© 2002 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353
Manual Revised 09/06; 11/06.
Page 2
SPECIFICATIONS
Body Construction Molded PVC, Stamped & Ground Stainless Steel
Head 3 Removable Flex Foils
Charging Power Source 120 V~ / 60 Hz, 2,450 RPM
Battery
Power Cord 3’3” Length. UL Listed, 2-Prong Plug
Charging Time 8 - 16 hrs.
Trimmer Width 7/8”
Number of Cutters 3 Cutters with 6 Blades per Cutter
Internal NiCd ‘AA’ type
IMPORTANT! Remove before disposal, see page 5.
SAVE THIS MANUAL
You will need the manual for the safety warnings and precautions, assembly instruc­tions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry place for future reference.
SAFETY WARNINGS AND PRECAUTIONS
1.
Keep children away from product usage area. Do not allow children to handle
this product.
2.
Do not use this product if under the influence of alcohol or drugs. Read warning
labels on prescriptions to determine if your judgement or reflexes are impaired while
taking drugs. If there is any doubt, do not attempt to use this product.
3.
Stay alert. Watch what you are doing at all times. Use common sense. Do not
operate this product when you are tired or distracted from the job at hand.
4.
Check for damaged parts. Before using this product, carefully check that it will
operate properly and perform its intended function. Check for damaged parts and
any other conditions that may affect its operation. Replace or repair damaged or
worn parts immediately.
5.
Warning: To reduce risk of death or injury by electric shock, do not reach for a
plugged in shaver that has fallen into water. Unplug immediately. Some electrical
parts inside the clipper are electrically live, even with the switch “off”.
6.
Do not use while bathing or in a shower.
7.
Do not force product. It will do the job better and more safely at the rate for which
it was intended. Do not use inappropriate attachments in an attempt to exceed the
tool capacity.
8.
Replacement parts and accessories. When servicing, use only identical replace-
ment parts. Only use accessories intended for use with this product.
9.
Do not place or store appliance where it can fall or be pulled into a tub or sink.
Do not place in or drop into water or other liquid.
For technical questions, please call 1-800-444-3353.
Page 2SKU 40195
Page 3
Always unplug this appliance from the electrical outlet immediately after us-
10.
ing.
Unplug this appliance before cleaning.
11.
This appliance should never be left unattended when plugged in. Close supervi-
12.
sion is necessary when this appliance is used by, on, or near children or invalids.
Use this appliance only for its intended use, as described in this manual.
13.
Never operate if damage is done to cord or plug, or if the shaver has been
14.
dropped or damaged.
Do not operate with a damaged or broken blades, as injury may occur.
15.
Before use, make certain blades are aligned properly.
16.
Warning: People with pacemakers should consult their physician(s) before
17.
using this product. Electromagnetic fields in close proximity to a heart pacemaker
could cause interference to or failure of the pacemaker.
Warning: The warnings, cautions and instructions discussed in this instruction
18.
manual cannot cover all possible conditions and situations that may occur. It
must be understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.
UNPACKING
When unpacking, check to make sure all parts shown on the Parts List (page 6) are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible.
For technical questions, please call 1-800-444-3353.
Page 3SKU 40195
Page 4
CHARGING INSTRUCTIONS
Note: All numbers referenced below refer to the parts listed on page 6 of this manual.
Rechargeable Shaver (1) is charged by attaching Power Cord (4) to Shaver and
1.
electrical outlet. Push the Switch (5) down. Charging Indicator Light (3) will tell you
that charging is taking place. This will take 8-16 hours to charge. When fully charged,
your shaver can be used about 7 days. When charge is complete, disconnect power
cord.
4
3
Charging more than 16 hrs. can damage the life of the battery. Battery is sealed in
2.
Shaver casing (1) and cannot be replaced.
5
OPERATION INSTRUCTIONS
Take off Protective Cap (7). Push Switch (5) up. Using a soft touch to your skin, move
Shaver in the opposite direction of hair growth. Stretching the skin gives you a closer
shave. Once shaving is done, push Switch down and replace Protective Cover.
Trimmer Operation
Flip up Trimmer (2) on back of Shaver (1).
1.
At a right-angled direction, softly touch your skin where you want to trim. Work
2.
slowly.
When finished trimming, push Trimmer (2) back into flat position.
3.
Cleaning / Maintenance
9 10
2
After using, clean Shaver’s Three Cutting Heads (9) with Brush (8) after removing
Plastic Foil Cover (10). When clean, replace cover. Cleaning your Shaver will help
keep it working at maximum efficiency. Caution: Be careful not to pinch or cut
fingers when cleaning cutting heads.
For technical questions, please call 1-800-444-3353.
Page 4SKU 40195
Page 5
DISPOSAL INSTRUCTIONS
Important!
Note: This item contains a NiCd battery that must be recycled or disposed of
properly. Do not dispose of this item without first removing the NiCd battery
for proper disposal/recycling. Removing the battery will destroy the shaver and
should only be done prior to disposal.
Remove the two Screws on the back of the shaver towards the bottom.
1.
Flip up the Trimmer (2) and remove the two screws from the holes that are now
2.
exposed.
Swing the back housing of the Shaver up from the rear forward.
3.
Using wire cutters (not included), clip the two tabs that are soldered to the battery.
4.
Dispose of battery properly or recycle it. For information on free NiCd battery recy-
5.
cling, call 1-800-444-3353.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
For technical questions, please call 1-800-444-3353.
Page 5SKU 40195
Page 6
PARTS LIST AND DIAGRAM
Part Description Q’ty
1 Shaver 1
2 Trimmer 1
3 Indicator Light 1
4 Power Cord 1
5 Switch 1
6 Travel/Storage Pouch 1
7 Protective Cap 1
8 Shaver Brush 1
9 Cutting Heads 3
10 Removable Plastic Foil Cover 1
6
8
4
2
7
9 10 1 5
3
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
For technical questions, please call 1-800-444-3353.
Page 6SKU 40195
Loading...