Please read these instructions carefully before using this appliance. It contains important information which will help you get the best out of your appliance and ensure safe
and proper installation, use, care and cleaning.
Keep this manual in a convenient place so you can always refer to it for safe and
proper use.
If you sell the appliance, give it away, or leave it behind when you move, make sure you
also pass on this manual so that the new owner can become familiar with all features
and safety warnings.
Legend
Yes
No
General information and tips
Warning! Important safety information!
Environmental information
Disposal
The presence of this symbol on the product,
accessories or materials that goes with this information indicates that at the end of its useful
life the product or its electronic accessories
(e.g. cable, Aqua Stop hose) should not be disposed with other household waste. To prevent
possible damage to the environment or human
health from uncontrolled waste disposal, please
separate these items from other types of waste and recycle them. This will promote the sustainable reuse of material resources. Household
users should contact either the retailer where
they purchased the product or relevant local
authorities to find out how they can take this
item for environmentally safe recycling and safety.
Business users should contact their supplier and
check the conditions of the purchase. This product and its electronic accessories should not
be mixed with other commercial waste.
Technical data ........................................................................ 27-28
Safety
4
5
Safety
Before switching on the appliance for
the first time...
...make sure all transport bolts are removed.
...make sure the power cord is not caught under or in
the appliance and there is no damage or risk for damaging.
...make sure the power circuit fuse is rated for10A.
...use a separate earthed socket for the power supply.
...make sure the plug is always accessible.
...hold the plug and not the electric cable when unplugging
the power supply.
...check that hose joints and connections are firm and
by opening tap check for any water leaks.
...do not switch on the appliance until everything is properly
installed!
Do not …
...allow children or persons with reduced physical,sensory
or metal capabilities,or lack of experience and knowledge,
unless they are supervised or given instructions on how
to use the washer by someone responsible for the safety.
...install the appliance outdoors in a damp place, or in an
area which may be prone to water leaks
a water leak cut
dry naturally.
...expose machine to any frost, heat or direct sunlight.
...touch or use the appliance when barefoot or with wet or
damp hands or feet.
flammable detergent or d
...use
...use any
...remove or insert the plug in presence of flammable gas.
...place the appliance directly on a carpet.
flammable spr
power supply and allow the machine to
ry cleaning agent.
ays in close vicinity to the appliance
In the
.
event of
During daily use of the appliance...
...supervise children.
Ensure that they don’t play with the appliance and its packaging.
...ensure that appliance is not used by people with
reduced physical, sensory or mental capabilities, lack of
experience and knowledge.
...pull up zips, fix loose threads and take care for small items
to prevent laundry from being entangled. If necessary, use
an appropriate bag or net.
...switch off at the wall socket after each wash programme
to save electricity and for safety.
...keep the lower part of the porthole clean and open door
and detergent drawer if appliance is not in use to prevent
odours.
...a damaged power cord is only to be replaced by the
manufacturer, service agent or other specifically
qualified people.
Do not ...
...touch the door during the washing process, as it may get hot.
...place heavy objects or sources of heat or damp on top of
the appliance.
...hot wash rubber or sponge-like materials.
...open detergent drawer during any wash cycle.
...force the door to open, it is fitted with a self-lock
device and will open shortly after wash cycle end.
...open the door if the water level is visible over the
porthole.
...cover or encase the appliance during operation or after
wards as it will restrict
evaporate
.
an
y moistu
r
e or dampness to
76
InstallationInstallation
Preparation
Remove all packaging material including polystyrene base.
While opening the package, water drops may be seen on
plastic bag and po
water tests and quality control in the factory.
1
.
Removing the transportation bolts
The transportation bolts are designed for clamping antivibration components inside the appliance during transportation.
rthole. This is normal as a result from
Inlet hose
1. Connect inlet hose to the machines water inlet valve.
2. Connect inlet hose to a water tap.
3. Tighten inlet hose connections and turn on water supply.
Check for any water leaks. Stop all water leaks before
continuing with installation.
1. Remove the back cover.
2.
2
.
2. Remove bolts on the rear side and take out
from the inner side of the machine.
General information and tips:
Keep the transportation bolts in a safe place for later use.
If the machine is to be moved to another location, replace
transportation bolts to prevent damage.
4
3.
3.
3.
.
plasticspacers
3. Replace back cover by inserting it in the two gaps,its
Warning!
Appliance is only qualified for cold water supply!
Use the hose-set supplied with the appliance.
Old hose-sets should not be reused.
Drain hose
Drainage could be installed in different ways. Nevertheless,
level of drain hose has to reach between 80-100 cm.
If possible alwa
back of the appliance.
ys keep drain hose
fixed to the clip at the
convexity is facing outside.
1. Drain hose to sink
4. Fill the transportation bolt holes with blanking plugs.
4
.
Location
Install the machine on a solid and level floor surface ensuring it
has at least 20 mm clearance on
each side. The washer must not
be installed on any textured floor coverings (eg carpet, rugs).
Adjusting the feet
Use the drain hose bracket to keep drain hose end retained
and out of any water level.
Fix the bracket securely to avoid dropping due to operational
movements.
2. Drain hose to sink siphon
Connection has to be securely sealed and fixed to corresponding adapter above the siphoning part!
Adjust all feets to achieve a complete level position.This will
minimize vibrations and thus noise during use. It will also
reduce wear and tear. We recommend to use a spirit level
80 - 100 cm
for adjustment. Floor should be as stable and flat as possible.
1400
90
Time save
加速洗
70
1200
Eco
超净洗
60
1000
Soak
高水位
800
40
夜 洗
Anti crease
600
30
防皱浸泡
20
400
不甩干
常温
加漂洗
123
Rinse
Temp. M emoFunction Selection Spin Delay
lock
M
CottonDaily Washdirect drive
M
Synthetic
预约时间剩余时间
M
Mix
Wool
Underwear
Sport
负载
Jeans
Hygien
e
89
Shirts
Express 15'
Baby Care
Delicate
Hand Wash
Spin/Drain
Drum Clean
Time save
加速洗
Eco
超净洗
Soak
高水位
夜 洗
Anti crease
防皱浸泡
加漂洗
Rinse
lock
907060403020
常温
123
Temp.M emoFunction SelectionSpinDelay
14001200
预约时间剩余时间
1000
800600400
不甩干
负载
M
CottonDaily Washdirect drive
Synthetic
Mix
Wool
Underwear
Sport
Jeans
Hygiene
M
M
Express 15'
Baby Care
Delicate
Hand Wash
Spin/Drain
Drum Clean
Shirts
If the appliance is switched on, the display will illuminate and the current status icons
are visible. Refer the following pages for details. If no buttons or the program selector is
not touched the display will go dark after a short while to save energy. If the program
selector is turned the display will illuminate.
Touch this button gently to switch on. The display will illuminate.Touch it again for about
, the
1011
illuminate.
Time save
Eco
Use the ECO option to save water and energy.
Selecting ECO will reduce the wash temperature slightly and
alter the wash time.
Anti crease“:Gently wash and spin to prevent creasing.
Touch the Selection button (button b) to confirm the flashing
“Function” icon. A tick or 1, 2 or 3 will illuminate confirming
your selection.
The “Child Lock“ function stops any further changes to the
set program. To active, hold the “Function“ and “Selection“
buttons at the same time for 3 seconds. The lock icon will
illuminate. To deactivate the “Child Lock“ hold the “Function“
and “Selection“ buttons at the same time
for 3 seconds.
Touch it to increase programme end time in increments of
30 minutes from 30 mins – 24hr.Press the Start/Pause button
once you are satisfied with the delayed end time. You will
note the countdown of the delay time commence and
subsequently the remaining programme cycle time will be
displayed. The related symbol to the operation will display.
To cancel any functions or settings, hold “On/Off” for about 3
seconds. To cancel the running program, press “Start/Pause” and
then hold “On/Off” for about 3 seconds.
adjust
adjust
1213
HWF85DW1HWF75DW1
Hygiene
Shirts
Drum Clean
Hygiene
Shirts
Drum Clean
Hygiene
Shirts
4.0or3.5
4.0or3.5
4.0or3.5
4.0or3.5
8.5or7.5
4.0or3.5
4.0or3.5
70,0
1415
*General information and tips:
Standard programme for the Energy and Water Labelling according to
AS/NZS2040.1:2005:
HWF75DW1
The detergent dosage: rated capacity* 12.5g*75% and-foam aid is 15g.
Detergent dissolvent method: Dissolve the detergent fi
the machine when the main wash starts.
HWF85DW1
The detergent dosage: rated capacity* 12.5g*75% and-foam aid is 17g.
Detergent dissolvent method: Dissolve the detergent first and pour the dissolved detergent into
the machine when the main wash starts.
is the
is the
and the recommended
kg
rst and pour the dissolved detergent into
and the recommended
kg
8.5or7.5
Drum Clean
The actual water temperature may differ from the declared cycle temperature.
If the machine is used for commercial purposes the warranty will be void. Do not use for
purposes other than that which the machine is designed for. Follow the instruc ons given
on the label of each garment and wash only machine -washable garments.
This appliance is only for domestic use inside the house. If it is used for commercial,
industrial or not intended purposes any Haier guarantee will not be valid anymore.
Consider instructions on each garment label and wash only machine-washable
laundry.
Power supply
1716
Loading the appliance
Open thedoor and put in the laundry piece by piece.
Close the door carefully. Don‘t overload. Check if you can
put a hand upright on top of load.
Daily useDaily use
Time save
加速洗
Eco
超净洗
Soak
高水位
夜 洗
Anti crease
防皱浸泡
加漂洗
123
Rinse
907060403020
常温
Temp. M emoFunction Selection Spin Delay
M
Cotton Daily Wash
1400
M
Synthetic
Shirts
1200
预约时间剩余时间
M
1000
Mix
Express 15'
800
Wool
Baby Care
R
600
Under-
Delicate
400
wear
不甩干
Hand Wash
Sport
负载
Spin/Drain
Jeans
Drum Clean
Hygiene
Connect the washing machine to the power supply (220V to
240V~/50Hz).
Water connection
Turn on the tap. The water must be clean and clear.
Warning!
Before use, turn tap on and check for any leackage.
Preparing laundry
Sort out clothes according to fabric (cotton, synthetics, wool
or silk) and to how dirty they are.
Separate white clothes from coloured ones. Wash coloured
textiles first by hand to check if they fade or run.
Garments without hems, delicates and finely woven textile
such as fine curtains are to be put into a wash bag (hand or
dry cleaning would be better).
Close zippers and hooks, make sure the buttons are sewn
on tightly and place small items such as socks, belts, bras, etc.
in a wash bag.
Unfold large pieces of fabric such as bed sheets, bedspreads
etc.Turn clothes inside out. Empty pockets (keys, coins, etc.)
and remove harder decorative objects (e.g. brooches).
General information and tips:
After installation or long down time ,run programme
“Drum Clean“ with no load and add detergent in
washing agent compartment (2) to remove possibly
corruptive residues.
Selecting detergent
Washing effi ciency and performance will vary depending
on detergent quality. Use only machine wash approved
detergent and if needed specifi c detergents, e.g. for synthetic and woolen fabric.
Be mindful of a
lwa
ys detergent
manufacturer recommendations.
General information and tips:
Remove detergent residues before next wash cycle.
Please follow given detergent dosage recommendation
When using “Prewash“ add half of the nominal dosage.
Adding detergent
Slide out the detergent drawer and put the required chemicals into corresponding compartments. Push back the
drawer gently.
Warning!
Non-textile, as well as small, loose or sharp-edged items may cause
malfunctions and damage clothes and appliance.
M
CottonDaily Wash
M
Synthetic
M
Mix
Wool
R
Underwear
Sport
Jeans
Hygiene
Time save
Eco
M
CottonDaily Wash
M
Synthetic
M
Mix
Wool
R
Underwear
Sport
Jeans
Hygiene
Express 15'
Baby Care
Hand Wash
Spin/Drain
Drum Clean
Shirts
Delicate
Shirts
Express 15'
Baby Care
Delicate
Hand Wash
Spin/Drain
Drum Clean
direct drive
To get the best washing results, select the program that is
most suitable to the laundry type loaded. Select program
by turning the program selector dial.
M
2 mins
later.
1819
M
CottonDaily Wash
M
Synthetic
M
Mix
Wool
R
Underwear
Sport
Jeans
Hygiene
Express 15'
Baby Care
Hand Wash
Spin/Drain
Drum Clean
Shirts
Delicate
direct drive
hold
Removing laundry promptly at the end of the cycle will minimise
wrinkling.
2021
Choose the best Detergent
Universal
Wool
Mix
Synthetic
Cotton
Express 15’
Delicate
L
P
oOptional
---
L/P
L/P
L/P
L
-
Detergent
Powder
No-
Leave
Before the next use,carefully check power cord,water inlet
Colour
L/P
L/P
L/P
L
-
Delicate
Special
L
-
L
-
-
L
Temperature range in °C
-
-
-
-
-
06 - dlocdiuqiL
40 - 90
---
---
Softener
O
O
O
O
O
O
22
23
Display code
noituloSesuaCedoC
Auto
Lo
HALF
Automatic
load detection.
Weighing the laundry load in
the drum.
FULL
HI
1:25Remaining wash cycle time.Refer to display symbol on page 9.
19:30Remaining delay start timeLikely showing the delay start operation.
Lock
Door cannot be opened due to
water level or hot water in the
drum.
EndEnd of cycle.
E1Drainage error, water not emptied. Check drain hose for blockage and that it is
E2Lock – error with doorShut the door properly.
E4Water level not reached after 8
minutes.
Drain hose is self-syphoning.
E8Water protective level - error.Auto release.Otherwise contact the
af ter sales service.
F3Temperature sensor - error.Contact the After sales service.
F4Heating error (Appears at the end of
a cycle .)
F7Motor - error.Contact theAfter
FbWater overflow.Close tap immediately.
Contact the After sales service.
FAWater level sensor error.Contact theAfter sales service.
FCElectronic control - error.Contact theAfter sales service.
UnbUnbalanced load and not able to
spin.
Laundry weight detection in progress, please
wait until program cycle time is displayed.
Please wait until program cycle time is
displayed: Lo = small load;HALF = half load;
FULL = optimized weight load;
HI = full load.
Refer to display symbol on page 9
Wait for the program to end or cancel the
program and select the Spin/Drain program.
In case there is still hot water in the drum,
to avoid scalding , select the Handwash
program and leave it to wash for several
minutes then select the Spin/Drain program.
This should allow the drum to cool down.
properly installed.
Check if water supply
and water pressure
is normal.
Contact the After sales service.
sales service.
Check and balance the laundry load in the
drum. Also reduce the load if too heavy.
Restart with a spin program.
If using liquid detergent, it is not recommended to activate the delayed start. Refer to the
detergent manufacturers packaging for recommended dosage!
info: Modern washing detergents at low temperatures.
2322
TroubleshootingTroubleshooting
lever
In case of power failure
The current programme and its setting will save. When
power supply is restored operation will resume . To cancel it,
“Start/Pause“ and then “Power“ for about 3 sec.
touch
If there is a power failure during a wash cycle your washer
will stop and the door will remain locked. You can unlock
the washer door to remove your clothes by opening the
pump filter cover at the bottom right of your washer.
Simply place a coin or flathead screwdriver in the slot of the
cover and slide it sidewards, then pull the door release tab.
Do not attempt to do this if the water level in the washer is
above the level of the door. When power is restored you
will need to restart your machine by simply pressing the
POWER button. The washer will remember where in the
cycle it was up to. to advise the meaning of the content.
Be careful, the load may be hot, so you may get burnt.
Troubleshooting without display code
Problem Cause Solution
Washing machine Power failure. Check power supply.
fails to operate. Machine has not been switched on. Switch the machine on.
Door is not properly closed. Close the door properly.
Programme is not yet started. Press “Start/Pause“ button.
Washing machine No chosen programme. Set programme and start it.
will not fillWater tap is closed. Turn
with water. on water tap.
Inlet hose is kniked. Check inlet hose. Inlet hose filter is blocked. Unblock inlet hose filter.
Water pressure is less than Check water pressure.
0,03 MPa.
Water supply failure. Ensure the water supply.
Door is not properly closed. Close doorproperly.
Problem Cause Solution
Drainage failure Drain hose is blocked. Unblock drain hose.
Drain hose end is higher than Make sure that drain hose
100 cm above floor level. is properly installed.
Pump filter is blocked. Clean pump filter.
Strong vibration Not all transportation bolts Remove all transportation
while spinning have been removed. bolts.
Washing machine is located Make sure that washing
on an uneven surface /or is machine is on an even sur not levelled. face and levelled.
Machine load is not correct.Adjust amount of laundry.
Operation stops Water or electric failure. Check power
before completing and water supply.
wash cycle
Operation stops Appliance displays error code. Note e
for a period of time Problem due to load pattern.
to page 19
rror code. and refer
Programme performs If it seems appropriate
soaking cycle? cancel operation.
Excessive foam Detergent is not a appropriate. Check detergent
in drum and/or recommendations.
detergent drawer Excessive use of detergent. Reduce amount of detergent
Automatic adjustment Washing programme This is normal and doesn‘t
of washing time duration will be adjusted
affect functionality.
depending on load.
Spinning fails Unbalance of laundry. Check machine load. Run
the Spin/Drain programme
again.
Machine is draining Height of drain hose is Make sure that drain hose
while being filled below 80 cm. is properly installed.
Drain hose end is in water.
General information and tips:
If too much foam is visible during spin cycle , the motor will stop and drain pump will
activate for 90 seconds. If that elimination of foam fails up to 3 times, programme
ends without spinning.
waste
26
27
Warning!
securely
10
is properly
HWF75DW1
7.5
Max
1200
850 x 600 x 595
withis
69
HWF85DW1
Max
28
8.5
71
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.