Haier HWE18VCN, HWE24VCN, HWE15XCN User & Care Manual

User & Care Guide Guide d'utilisation et d'entretien Guía de uso y cuidado
Room Air Conditioner
Climatiseur individuel
Aire acondicionado
de uso doméstico
HWE15XCN HWE18VCN HWE24VCN
°F/°C
Hr
MODE SPEED TIMER
FAN
HIGH
MED
ENERGY SAVE
LOW
COOL
DEHUM
AUTO COOL
TEMP/TIME
FILTER RESET
ON
CLEAN FILTER
OFF
SLEEP
POWER
AUTO RESTART
Design may vary by model number.
This user manual is to be only use for electronic control 14,500 BTU, 18,000 BTU and 24,000 BTU - Some models may have an additional letter after the model number.
0010568060
numéro de modèle.
Ce guide d'utilisation doit être utiliséstrictement avec les modèles à commande électronique de 14,500BTU, 18,000 BTU et 24,000 BTU - Sur certains modèles, le numéro de modèle peut être suivi d'une lettre.
El diseño puede variar conforme al
número de modelo
Este manual del usuario sólo se debe utilizar para el control electrónico 14,500 BTU, 18,000 BTU y 24,000BTU– Algunos modelos pueden tener
unaletraadicional después delnúmerode modelo.
ENGLISH
TABLE OF CONTENTS
SAFETY INFORMATION............................................................................................................. 2
Important Safety Precautions ................................................................................................ 2-3
Operational Safety & Warnings .................................................................................................. 4
INSTALLATION REQUIREMENTS .............................................................................................5
Tools and Parts ............................................................................................................................ 5
Location Requirements ..............................................................................................................6
Electrical Requirements ....................................................................................................... 7-10
HOW TO INSTALL ....................................................................................................................11
Unpacking the Air Conditioner .................................................................................................11
Preparing the Air Conditioner: .......................................................11-13
Preparing the Window: .........................................................................14
HWE15XCN/HWE18VCN
Completing the Installation: Preparing the Air Conditioner:
Preparing the Window: .............................................................................................18
HWE24VCN
Completing the Installation: .....................................................................................19
Completing the Installation ......................................................................................................20
HWE15XCN/HWE18VCN
HWE15XCN/HWE18VCN
HWE24VCN
HWE24VCN
............................................................................16-17
..................................................................15
USING YOUR AIR CONDITIONER ...........................................................................................21
Starting the Air Conditioner ...............................................................................................21-24
Using the Remote Control ..................................................................................................25-27
Changing the Air Direction .......................................................................................................27
Normal Sounds of an Air Conditioner ......................................................................................28
CARING FOR YOUR AIR CONDITIONER ................................................................................29
Cleaning the Air Filter ...............................................................................................................29
Cleaning the Front Panel ..........................................................................................................30
Annual Maintenance .................................................................................................................30
Customer Service .....................................................................................................................30
TROUBLESHOOTING ..............................................................................................................31
LIMITED WARRANTY ...............................................................................................................32
PRODUCT REGISTRATION
Thank you for purchasing our Haier product. This easy-to-use manual will guide you in getting the best use of your product.
Model number
Remember to record the model and serial numbers. They are on a label on the side of your unit.
Staple your receipt to your manual. You will need it to obtain warranty service.
Serial number
Date of purchase
ENGLISH
1. Use this air conditioner only for its intended application as described in this
IMPORTANT SAFETY PRECAUTIONS
WARNING
THE INFORMATION IN THIS USE & CARE GUIDE MUST BE
FOLLOWED TO MINIMIZE THE RISK OF PERSONAL INJURY, FIRE,
ELECTRIC SHOCK OR OTHER UNSAFE CONDITIONS.
THE INSTRUCTIONS IN THIS USE & CARE GUIDE ARE NOT MEANT
TO INCLUDE EVERY POSSIBLE CONDITION OR SITUATION THAT
MAY OCCUR. USE CAUTION AND CARE WHEN INSTALLING, OPERATING
AND CLEANING THE AIR CONDITIONER.
Use & Care Guide.
2. This air conditioner must be properly installed and use the correct wall outlet that matches with the air conditioner’s power supply cord in accordance with the Installation Section of this Use & Care Guide before it is operated.
3. Never unplug the air conditioner by pulling on the power supply cord. Always grip the plug firmly and pull straight out from the wall outlet.
4. Replace the power supply cord immediately if it becomes damaged in any way. A new power supply cord must be purchased from the air conditioner manufacturer and installed by a qualified technician. DO NOT use a power supply cord that is cracked, split, cut, or damaged anywhere along its length or either at the plug end or connector end.
5. Turn off the air conditioner and unplug it from the wall outlet before performing any cleaning or maintenance.
6. Do not store or use combustible or flammable materials or liquids on or near the air conditioner.
7. If the wall outlet configuration does not match the plug configuration on the air conditioner, the wall outlet must be changed by a qualified electrician.
PAGE 2 SAFETY INFORMATION
IMPORTANT SAFETY PRECAUTIONS
8. This air conditioner contains R410a refrigerant and requires certified technicians to use the proper equipment, tools and safety standards that are approved for this refrigerant. Use only equipment certified for R410a refrigerant. In addition, under federal law, all refrigerant must be properly removed from the air conditioner prior to its disposal.
For responsible disposal of the product please contact
or your local municipality for recycling options.
ENGLISH
READ AND FOLLOW THE
SAFETY INSTRUCTIONS CAREFULLY.
SAVE THESE INSTRUCTIONS
SAFETY INFORMATION PAGE 3
ENGLISH
1. This air conditioner contains no consumer serviceable parts. If you have
2. Be sure that the air conditioner is properly and securely installed in
3. DO NOT drill any holes in the base or sides of the air conditioner.
4. DO NOT place fingers or objects in the air discharge or air intake in the
5. DO NOT operate the air conditioner with a protective cover on the
OPERATIONAL SAFETY & WARNINGS
problems or questions regarding the operation of your air conditioner always call Haier Customer Service: 1-877-337-3639.
the window according to the installation instructions included in this Use & Care Guide.
front of the air conditioner.
outside section.
6. DO NOT block the air discharge or air intake areas on the front panel.
7. DO NOT block the side louvers on the outside of the air conditioner.
8. DO NOT place any objects either on the indoor or outdoor sections of the air conditioner
9. Operate the air conditioner with the air filter installed.
10. Keep this Use & Care Guide, carton and packing material for future use
in removing, storing and reinstalling the air conditioner.
PAGE 4 SAFETY INFORMATION
TOOLS AND PARTS
Read and follow the instructions provided with any tools listed here.
TOOLS NEEDED
Phillips head screwdriver
Socket wrench & sockets
ENGLISH
Pliers Flat-blade screwdriver Scissors Level
Tape measure Cordless drill and 1/8” bit Pencil
Adjustable wrench
PARTS SUPPLIED:
Check that all parts for your specific air conditioner are included in the parts package.
NOTE: If parts are missing, call Haier Customer Service: 1-877-337-3639.
IMAGE PART 14,500 BTU, 18,000 BTU 24,000 BTU
Top channel
Foam seal
Installation
brackets
1 1
1 1
2 2
Window lock
1 1
bracket
3/8" self-
12 10
tapping screws
1" wood screws
3/8" bracket
8 10
6 6
screws
2-1/2" bolt and
2 2
lock nut
Side curtain
assembly
ON/OFF
MODE
SPEED
TIMER
TEMP/TIME
TEMP/TIME
INSTALLATION REQUIREMENTS PAGE 5
Remote control 1 1
2 2
ENGLISH
IMPORTANT: Observe all governing codes and ordinances. Check the location where the air
conditioner will be installed. Make sure you have everything necessary for correct installation.
The site of installation should provide:
A grounded electrical outlet within 4 ft. (122 cm) of where the power cord exits the air
NOTE: Do not use an extension cord, plug adapter, surge protector or multi-outlet adapter.
• Free movement of air in the room to be cooled.
• A large enough opening for the air conditioner.
• Unit must not be installed in a through-the-wall sleeve.
NOTE: The outside cabinet louvers must not be obstructed by bushes, trees, etc. Air must be able
LOCATION REQUIREMENTS
conditioner.
to pass freely through the cabinet louvers.
WINDOW INSTALLATION
(See Fig. 1)
Fig. 1
Window opening measurements: (See Fig. 1)
HWE15XCN/HWE18VCN HWE24VCN A. Width B. Height
28-3/8" - 38" 31-1/4" - 40"
17-3/8" 20-1/4"
B-HEIGHT
WARNING
• Electrical shock hazard
• Plug into a mating, grounded 3 prong outlet.
• Do not remove the ground prong from the power supply cord.
• Do not use a plug adapter, extension cord, surge protector, or multi-outlet adapter
• Failure to follow these instructions can result in injury, fire, or electrical shock.
A-WIDTH
PAGE 6 INSTALLATION REQUIREMENTS
ENGLISH
ELECTRICAL REQUIREMENTS
WARNING
ELECTRICAL SAFETY and WARNINGS
1. DO NOT cut or remove the grounding prong on the attached power supply cord. Doing so may cause sparks or re, and voids all warranties. For safety purposes the air conditioner must be properly grounded.
2. To avoid a re hazard or possible electric shock, DO NOT use an adapter plug, extension cord, surge protectors, or multi-outlet adapters with the air conditioner.
3. The power supply cord is equipped with a 3-prong plug which mates with the grounded 3-prong wall outlet to minimize the possibility of electrical shock from this air conditioner.
4. The power supply cord includes a leakage current detection interrupter device (LCDI). A RESET and TEST button are on the plug case. The device should be tested on a periodic basis by pressing the TEST button and then the RESET button while outlet. If the TEST button does not trip or the RESET will not stay engaged, do not use the air conditioner and contact a qualified service technician.
5. Have the wall outlet and circuit inspected by a qualified electrician to ensure that the wall outlet is properly grounded.
6. If there is a 2-prong wall outlet present and not a 3-prong wall outlet, it is the responsibility of the user to have it replaced with a properly grounded 3-prong outlet.
7. The air conditioner should always be plugged into a dedicated electrical outlet which has a voltage rating that matches the serial label on the side of the air conditioner.
8. The electrical ratings for your air conditioner are listed on the Model/Serial Number label. The Model/Serial Number label is located on the side of the air conditioner cabinet.
9. Specific electrical requirements are listed in the chart below. Follow the requirements for type of plug on the power supply cord.
it is plugged into the wall
the
INSTALLATION REQUIREMENTS PAGE 7
ENGLISH
RESET
TEST
230V
15 Amp
230V
20 Amp
ELECTRICAL REQUIREMENTS cont.
POWER SUPPLY CORD (See Fig.2)
Fig. 2
Wiring Requirements
For model HWE15XCN
HWE15XCN
115-volt (103.5 minimum to 126.5 maximum)
15-amp time-delay grounded fuse or circuit breaker
Use on single outlet circuit only.
For model HWE18VCN
230/208 volt (187 min. to 253 max.)
HWE18VCN
115V
15 Amp
15-amp time-delay fuse or circuit breaker
Use on single outlet circuit only.
230V
15 Amp
For model HWE24VCN
230/208 volt (187 minimum to 253 maximum)
20-amp time-delay grounded fuse or circuit breaker
HWE24VCN
Use on single outlet circuit only.
230V
REQUIRED GROUNDING METHOD
(See Fig.2)
20 Amp
This air conditioner must be grounded. This air conditioner is equipped with a power supply cord that has a 3 prong grounding plug. The power supply cord must be plugged into a mating, grounded 3 prong outlet, and grounded in accordance with all local codes and ordinances. If a mating outlet is not available, it is the customer’s responsibility to contact a qualified electrician and ensure that a properly grounded 3 prong outlet is installed.
POWER SUPPLY CORD (See Fig.3)
Fig. 3
A
B
NOTE: Your air conditioner's plug may differ slightly in appearance
from the one shown. A. Reset button B. Test button
This room air conditioner is equipped with an
a leakage current detection interrupter (LCDI)
power supply cord required by UL. This power supply cord contains a current detection device. If the power supply cord is crushed, this device will detect current leakage and power will be disconnected from the air conditioner. If this po
wer supply cord is damaged, it cannot be repaired and must be replaced with a cord from the product manufacturer. If the power supply cord is damaged call Haier Customer Service: 1-877-337-3639.
PAGE 8 INSTALLATION REQUIREMENTS
ELECTRICAL REQUIREMENTS cont.
WARNING
• Electrical shock hazard
• Do not use a plug adapter, extension cord,
• Plug into a mating, grounded 3 prong
outlet.
• Do not remove the ground prong from the
power supply cord.
IMPORTANT: Observe all governing codes and ordinances. Check the location where the air
conditioner will be installed. Make sure you have everything necessary for correct installation.
surge protector, or multi-outlet adapter
• Failure to follow these instructions can
result in injury, fire, or electrical shock.
ENGLISH
THE LOCATION SHOULD PROVIDE:
A grounded electrical outlet within 4 ft. (122 cm) of where the power supply cord exits the air
conditioner, for models: HWE15XCN HWE18VCN HWE24VCN
NOTE: Do not use an extension cord, plug adapter, surge protector or multi-outlet adapter.
Free movement of air in the room to be cooled.
A large enough opening for the air conditioner.
The air conditioner must not be installed in a through-the-wall sleeve. It can only be installed in
a double-hung window or in a wall. .
NOTE: The outside cabinet louvers must not be obstructed by bushes, trees, etc. Air must be
able to pass freely through the cabinet louvers.
INSTALLATION REQUIREMENTS PAGE 9
ENGLISH
TO TEST YOUR POWER SUPPLY CORD:
1. gulP power supply cord into a mating, grounded 3 prong outlet.
2. Press RESET (on some devices, a green light will turn on).
3. rP ess TEST (listen for click; Reset button will trip, and on some devices,
4. rP ess and release RESET (listen for click; Reset button will latch, and on
NOTE:
ELECTRICAL REQUIREMENTS cont.
(See Fig.4)
Fig. 4
a green light will turn off).
some devices, a green light will turn on). The power supply cord is ready for operation.
The RESET button must be pushed in completely for proper operation. (See Fig.5) The power supply cord must be replaced if it fails to trip when the test
button is pressed or fails to reset. DO NOT turn the air conditioner on or off by unplugging the power
supply
cord from the outlet. Always turn the air conditioner on or off at
the control panel or by using the remote control. A damaged power supply cord must be replaced with a new power
supply cord obtained from the product manufacturer and installed my a qualified service professional. It cannot be purchased at a retail store and must not be repaired by the user.
fI the power supply cord is damaged please call Haier Customer Service:
1-877-337-3639.
The power supply cord contains no user-serviceable parts.
Opening the tamper-resistant case voids all manufacturer warranties.
RESET
Fig. 5
TEST
PAGE 10 INSTALLATION REQUIREMENTS
UNPACKING THE AIR CONDITIONER
WARNING
EXCESSIVE WEIGHT HAZARD
When moving or lifting the air conditioner, use two or more people.
Wear gloves when handling the air conditioner to protect against
possible sharp edges and metal fins.
REMOVE PACKAGING MATERIALS
Remove packaging materials. Save the carton and the foam packaging for storing the unit when
not in use.
NOTE: toN oDevomer ot renoitidnoc ria eht edisni slairetam gnikcap lanretni ON era erehT
open the cabinet.
ENGLISH
Handle the air conditioner gently.
Keep the air conditioner upright and level. Do not set the air conditioner on its side, front, back
or upside down. The air conditioner must be standing upright for 2 hours prior to installation and operation.
PREPARING THE AIR CONDITIONER
Unpack unit in the oor near the installation location
1. Remove the two front attachment screws (A). Keep these screws for later use. Separate the
cabinet from the front panel. (See Fig.6)
2.
Remove the two screws per side (B) found at the bottom of the outer cabinet. Using the basepan handle, slowly and evenly pull out the chassis from the cabinet. Use two or more people to move the air conditioner.
CAUTION: rf citsalp esopxe reveN ont or
grille to extreme temperatures.
Fig. 6
B
B
A
B
HOW TO INSTALL PAGE 11
ENGLISH
PREPARING THE AIR CONDITIONER cont.: HWE15XCN/HWE18VCN
Assemble and install side curtains and top channel
(See Fig.7)
FOR MODELS: HWE15XCN HWE18VCN
3/8" Self Tapping Screws
Fig. 7
Top Channel
Front
1. Install the top channel with four (4) 3/8” self-tapping screws. (See Fig.7)
2. Slide left-hand curtain assembly into left side of top and bottom channels. Repeat for right­hand curtain assembly. (See Fig.8)
3. Fasten curtain retainer strips to the sides of the cabinet with eight (8) 3/8” self-tapping screws. (4) Self tapping screws on each side.
Fig. 8
3/8" Self
Tapping Screws
Top Channel
Side Curtains
3/8" Self Tapping Screws
PAGE 12 HOW TO INSTALL
PREPARING THE AIR CONDITIONER cont.: HWE15XCN/HWE18VCN
HEIGHT
WIDTH
1. Measure the width of the window opening. (See Fig.9)
2. kraM the center line on the inside of the windowsill with a pencil. (See Fig.10)
ENGLISH
WIDTH OF
CENTER LINE
WINDOW OPENING
Fig. 9
WIDTH
Fig. 10
CENTER
NOTES AND WARNINGS:
• Be sure your air conditioner does not fall out of the opening during installation or removal.
A grounded electrical outlet must be within 4 ft. (122 cm) of where the power supply cord
exits the air conditioner.
• Do not block the air discharge or air intake areas on the front panel.
• Do not block the louvers on the outside of the air conditioner.
INSTALL THE CABINET IN THE WINDOW (See Fig.11)
FOR MODELS: HWE15XCN HWE18VCN
1. Center the cabinet in the windowsill. Make sure to place the cabinet so that it is resting on the windowsill with a ¼" to ½" downward tilt towards the outside (See Fig. 11). Lower the window sash behind the front flange of the top channel to hold the unit in place. The bottom channel must rest behind the window sill.
NOTE: The appearance of your model may differ from the one shown.
Fig. 11
HOW TO INSTALL PAGE 13
Bottom Channel
Window Sill
ENGLISH
2. Expand both curtains so they contact the side window frame. Install four (4) 1” wood screws,
3. Use three (3) 1” wood screws to secure the cabinet, 1 to the window sash, 2 to the window sill.
4. Install two(2)-1/2” leveling bolts to the
5. Secure cabinet to left and right
6. Adjust two (2)-1/2" leveling bolts to
PREPARING THE WINDOW: HWE15XCN/HWE18VCN
two (2) in the upper corners of the curtains and two (2) in the lower corners of the curtain. (See Fig.12)
(See Fig.12)
Fig. 12
left and right brackets. (See Fig.13)
brackets using six (6) 3/8” bracket screws. 3 on each side. (See Fig.14)
proper length and use nut lock to secure bolt. Use a wood block between the leveling bolts and the wall if required.
Window Sash
Top Channel
Fig. 13
Wood Block
2-1/2 Bolt and
Nut Lock
1" Wood
Screws
Fig. 14
3/8" Self
Tapping Screws
PAGE 14 HOW TO INSTALL
COMPLETING THE INSTALLATION: HWE15XCN/HWE18VCN
ENGLISH
COMPLETE THE INSTALLATION
1. Uncoil the included foam seal. (See Fig.15)
2. Insert the foam seal behind the top of the lower window sash and against the glass of the upper window. (See Fig.16)
A. Top of lower window sash B. Foam seal
3. Place the window lock bracket as shown. Use
one(1) 1⁄8” drill bit to drill a starter hole through the hole in the window lock bracket and into the upper window sash. (See Fig.17)
4. Attach the window lock bracket to the upper window with one (1) 1” wood screw to secure the window in place. (See Fig.17)
(A) Top of lower
window sash
INSTALLING THE CHASSIS TO THE CABINET (See Fig.18)
When moving or lifting the air conditioner chassis, use two or more people. Wear gloves when handling the air conditioner to protect against possible sharp edges and
metal fins.
1. Pick up the chassis carefully and evenly.
Fig. 17
Window Lock
Bracket
Fig. 15
(B)Foam seal
Fig. 16
2. Slide the chassis into the cabinet. (See Fig.18)
3. Reinstall the front panel.
4. Secure the front panel to the chassis using the screws removed at the start of the installation. (A) (See Fig.19)
5. Reinstall two of the screws removed from the cabinet at the start of the installation. (B) (See
Fig.19)
6. Plug the unit in. Press RESET on the power supply cord. A green light will come on. See “Electrical Requirements."
Fig. 18
Fig. 19
B
B
HOW TO INSTALL PAGE 15
B
A
ENGLISH
PREPARING THE AIR CONDITIONER: HWE24VCN
Assemble and install side curtains and top channel
(See Fig.20)
FOR MODEL: HWE24VCN
3/8" Self Tapping Screws
Fig. 20
Top Channel
Front
1. Install the top channel with four (4) 3/8” self -tapping screws. (See Fig.20)
2. Slide left-hand curtain assembly into left side of top and bottom channels. Repeat for right­hand curtain assembly. (See Fig.21)
3. Fasten curtain retainer strips to the sides of the cabinet with six (6) 3/8” self-tapping screws. (3) Self tapping screws on each side. (See Fig.21)
Fig. 21
3/8" Self
Tapping Screws
Top Channel
Side Curtains
3/8" Self
Tapping Screws
PAGE 16 HOW TO INSTALL
PREPARING THE AIR CONDITIONER: HWE24VCN
HEIGHT
WIDTH
ENGLISH
1. Measure the width of the window opening.
(See Fig.22)
2. kraM the center line on the inside of the windowsill with a pencil.
WIDTH OF
(See Fig.23)
CENTER LINE
WINDOW OPENING
Fig. 22
WIDTH
Fig. 23
CENTER
NOTES AND WARNINGS:
• Be sure your air conditioner does not fall out of the opening during installation or removal.
A grounded electrical outlet within 4 ft. (122 cm) of where the power supply cord exits the air
conditioner.
• Do not block the air discharge or air intake areas on the front panel.
• Do not block the louvers on the outside of the air conditioner.
INSTALL THE CABINET IN THE WINDOW
FOR MODEL HWE24VCN (See Fig.24)
1. Center the cabinet in the windowsill. Make sure to place the unit so that it is resting on the windowsill with a ¼" to ½" downward tilt towards the outside. Lower the window sash behind the front flange of the top channel to hold the unit in place. The bottom channel must rest behind the window sill. (See Fig.24)
NOTE: The appearance of your model may differ from the one shown.
Fig. 24
Bottom Channel
Window Sill
HOW TO INSTALL PAGE 17
ENGLISH
2. Expand both curtains so they contact the window frame. Install four (4) 1” wood screws, two (2)
3. Use three (3) 1” wood screws in the top
4. Use two (2) 1" wood screws to fix the case to
5. Install two (2)-1/2” leveling bolts to the left and
6. Adjust two (2)-1/2" leveling bolts to the proper
PREPARING THE WINDOW: HWE24VCN
in the upper right corners of the curtains and two (2) in the upper left corners of the curtain. (See Fig.25)
mounting channel.
window sash.
right brackets. (See Fig.27) Secure cabinet to left and right brackets using six (6) 3/8” self -tapping screws.Three (3) on each side.
length and use nut lock to secure bolt. Use a wood block between the leveling bolts and the wall ifrequired. (See Fig.26)
1" Wood
Screws
Fig. 25
Wood Block
Fig. 26
2-1/2 Bolt and
Nut Lock
(2) 1" Wood
Screws
Fig. 27
3/8" Self
Tapping Screws
PAGE 18 HOW TO INSTALL
COMPLETING THE INSTALLATION: HWE24VCN
ENGLISH
COMPLETE THE INSTALLATION
1. Uncoil the included foam seal. (See Fig.28)
2. Insert the foam seal behind the top of the lower window sash and against the glass of the upper window. (See Fig.29)
3. Place the window lock bracket as shown. Use one (1) 1⁄8” drill bit to drill a starter hole through the hole in the window lock bracket and into the
Top of lower
window sash
upper window. (See Fig.30)
4. Attach the window lock bracket to the upper window with one (1) 1” wood screw to secure the window in place. (See Fig.30)
INSTALLING THE CHASSIS TO THE CABINET
When moving or lifting the air conditioner chassis, use two or more people. Wear gloves when handling the air conditioner to protect against possible
sharp edges and metal fins.
1. Pick up the chassis carefully and evenly.
2. Slide the chassis into the cabinet. (See Fig.31)
(See Fig.31)
Fig. 30
Window Lock
Bracket
Fig. 28
Foam seal
Fig. 29
3. Reinstall the front cabinet.
4. Secure the front panel to the chassis using the screws removed at the start of the installation. (A) (See Fig.32)
5. Reinstall two of the screws removed from the cabinet at the start of the installation. (B) (See
Fig.32)
6. Press RESET on the power supply cord. A green light will come on. See “Electrical Requirements."
Fig. 32
Fig. 31
A
B
HOW TO INSTALL PAGE 19
ENGLISH
WARNING
• Electrical shock hazard
• Plug into a mating, grounded 3 prong outlet.
• Do not remove the ground prong from the power supply cord.
• Do not use a plug adapter, extension cord, surge protector, or multi-outlet adapter
• Failure to follow these instructions can result in injury, fire, or electrical shock.
WALL INSTALLATION
Construction and Installation NOTES:
1. Be certain that the location of the air conditioner in the wall conforms to all local building codes
COMPLETING THE INSTALLATION
before installation.
2. Consult with a qualified carpenter concerning installation.
3. When installing the air conditioner in a through-the-wall application, work from inside the room.
4. Each through-the-wall installation may be unique; therefore no additional parts are included.
5. Be certain that the section of the wall being used:
• Does not have electrical wiring in the location where the air conditioner will be installed.
• Does not have plumbing pipes in the location where the air conditioner will be installed.
• An existing electrical outlet that matches the power supply cord plug of the air conditioner. If no
outlet exists or the wrong type of mating outlet is present, consult with a qualified electrician to
install the proper outlet.
• Does not support major structural components.
• The finished sides of the wall opening should be structural wall members.
• Outside areas are not blocked.
See “Electrical Requirements" for full detail.
• Structural integrity of the wall must be maintained. Professional installation is strongly
recommended.
PAGE 20 HOW TO INSTALL
STARTING THE AIR CONDITIONER
°F/°C
ENGLISH
MODE
Hr
FILTER RESET
MODE SPEED TIMER
FILTER RESET
TEMP/TIME
TEMPERATURE / TIME
SPEED
FAN
ENERGY SAVE COOL
DEHUM
HIGH
MED
LOW
AUTO COOL
ON
OFF
SLEEP
CLEAN FILTER
POWER
AUTO RESTART
CLEAN FILTER INDICATOR
POWER
TIMER
* HWE24VCN does not have Auto Cool / Sleep Mode and Filter Reset.
Operating your air conditioner properly helps you to obtain the best possible results. This section explains how to operate this air conditioner.
IMPORTANT:
wait at least 3 minutes before turning it back on. This prevents the compressor from overloading. This 3 minute delay also applies when switching from cool mode to fan and back.
nehW you turn off the air conditioner , either at the control panel or with the remote control,
Do not operate your air conditioner in the Cool mode when the outside temperature is below
61°F (16° C). The inside evaporator coil will freeze up, and the air conditioner will not operate properly.
USING YOUR AIR CONDITIONER PAGE 21
ENGLISH
1. Carefully remove the clear plastic film from the control panel.
2. rP ess POWER once to turn on the air conditioner.
NOTE: nehW the air conditioner is rst plugged in, the LED display will show “88” for 3 seconds.
NOTE: To switch the temperature display between Fahrenheit (F) and Celsius(C), the air
HWE15XCN,HWE18VCN: To switch between °F and °C,press UP and DOWN buttons
HWE24VCN : To switch between °F and °C, press POWER button and hold for 5 seconds.
STARTING THE AIR CONDITIONER cont.
After the air conditioner is turned on for the rst time, the display will show the temperature 72˚ F and the fan is automatically set to Low speed and the Mode indicator will show ENERGY SAVE.
conditioner must be plugged in, and turned on. The change cannot be done using the remote control.
simultaneously and hold for 3 seconds.
3. Select Mode. Refer to “Mode.”
4. Select Speed. Refer to “Speed.”
5. Set Timer. Refer to “Temp/Time”
6. Reset the filter. Refer to “Filter Reset”
MODE
1. Press mode until you see the indicator light come on next to the desired setting.
2. Choose Fan, Energy Save, or Dehum.
FAN― Only the fan runs. Press SPEED to select High, Med or Low fan speed. The display shows
the current room temperature.
ENERGY SAVE― In this mode the fan runs only when cooling is needed. The fan will run for
3 minute after the compressor shuts off. The fan then cycles on for 1 or 2 minutes at 10 minute intervals until the set temperature. The compressor then turns back on.
COOL― Cools the room. Press SPEED to select High,Med , Low or Auto Cool fan speed. Press the
TEMP/TIME up or down arrow button to adjust the temperature.
DEHUM sdiA in removing humidity from the room. This setting will NOT cool the room.
Cool
temperature in the room is above the
PAGE 22 USING YOUR AIR CONDITIONER
STARTING THE AIR CONDITIONER cont.
SPEED
HIGH
MED
LOW
AUTO COOL
°F/°C
Hr
TEMP/TIME
FILTER RESET
ON
CLEAN FILTER
OFF
SLEEP
POWER
AUTO RESTART
1. rP ess FAN SPEED until; you see the indicator light come on next to the desired setting.
2. Choose High, Med, Low or Auto Cool
HGIH ―For maximum cooling
DEM ―For normal cooling
LOW―For minimum cooling
MODE SPEED TIMER
FAN
ENERGY SAVE COOL
DEHUM
AUTO COOL stsujdA the fan speed automatically to provide ideal cooling based on the room
temperature.
TIMER
To set the air conditioner to turn off between 1 hour and 24 hours (The air conditioner must be ON to set):
1. rP ess TIMER. Timer Off indicator light will flash. The display will show the remaining hours before the air conditioner will turn off.
ENGLISH
2. rP ess the TEMP/TIME up or down arrow button to change the delay time from 1 hour to 24 hours.
3. retfA 5 seconds, Timer Off indicator light will remain on. The display will show the left time to Timer OFF or the current temperature.
To set the Timer to turn on the air conditioner, keeping the previous settings:
1. Turn on the unit.
2. Press TIMER. Timer On indicator light will flash. The display will show the remaining hours before the air conditioner will turn on.
3. Press the TEMP/TIME up or down arrow button to change the delay time from 1 hour to 24 hours.
4. Timer On indicator light will remain on.
TO SET THE TIMER TO TURN ON THE AC, AND CHANGE THE PREVIOUS SETTINGS:
1. Turn on the air conditioner.
2. Adjust the mode to Fan, Cool Energy Save, or Dehum. For Fan or Dehum mode,adjust the fan speed to High, Med or Low. For Cool or Energy Save
3. mode, adjust the fan speed to High, Med, Low or Auto Cool.
NOTE:In Dehum mode,when the set temperature is close to the ambient temperature,the compressor may stop and the fan will run in low speed only.
4. Adjust the temperature between 61°F and 86°F (16°C and 30°C).
NOTE: In Fan mode, the temperature cannot be set.
5. rP ess TIMER. Timer On indicator light will flash. The display will show the remaining hours before the air conditioner will turn on.
6. rP ess the TEMP/TIME up or down arrow button to change the delay time from 1 hour to 24 hours.
7. Timer On indicator light will remain on.
USING YOUR AIR CONDITIONER PAGE 23
ENGLISH
TO CLEAR TIMER PROGRAM:
NOTE: Air conditioner can be either on or off.
Press TIMER until Timer indicator light turns off.
TO VIEW OR CHANGE THE REMAINING TIME (IN HOURS): TIMER OFF
1. Press the TEMP/TIME up or down arrow button to increase or decrease the time.
2. After 5 seconds, the display will show the remaining time to Time OFF or the current
TIMER ON
1. The display will show the remaining time.
STARTING THE AIR CONDITIONER cont.
temperature.
2. Press the TEMP/TIME up or down arrow button to increase or decrease the time.
3. After 5 seconds, the display will show the remaining time to Timer ON.
SLEEP
1. Press the TIMER button to choose Sleep mode. The indicator light will turn on.
2. The temperature will increase by 2˚F 1 hour after the mode is chosen. The temperature then increases another 2˚F after 1 hour. The unit will hold this temperatur
3. To turn off Sleep mode, press the TIMER button until the indicator light is off.
e for 6 hours then stops.
TEMP/TIME
1. Press the TEMP/TIME up arrow button to raise the temperature. Each time you press the TEMP/TIME up arrow button, the temperature will go up 1°F until it reaches 86°F (30°C).
Press the TEMP/TIME down arrow button to lower the temperature. Each time you press the
2. TEMP/TIME down arrow button, the temperature will go down 1°F until it reaches 61°F (16°C).
NOTE:
HWE15XCN HWE18VCN: After 5 seconds under Fan mode the display will show the current
temperature under Cool, Energy Save or Dehum mode the display will show the set temperature
HWE24VCN: After 5 seconds the display will show the current temperature.
PAGE 24 USING YOUR AIR CONDITIONER
USING THE REMOTE CONTROL
ENGLISH
FILTER RESET
This feature automatically notifies you that the air filter must be cleaned. The indicator light will come on after 240 hours of operation. Clean the air filter (refer to Care and Cleaning), place it back in the front panel, and press the Filter Reset button. The light will turn off.
NOTE: The raised dots are Braille for the visually impaired. (See Fig.20)
Remote control may differ in appearance from the image shown.
NOTE:
Remove and discard protective film prior to use. The remote control runs on one CR2025 battery (included). Replace battery after 6 months of use, or when the remote control starts to lose power. To change battery, rst
remove screw on back panel of remote.
POWER
HWE15XCN/HWE18VCN
Pr
ess ON/OFF to turn on the air conditioner.When you first press the ON/OFF button,the air conditioner will operate in Energy Save mode, low fan speed and temperature of 72°F. You can select any other mode to satisfy your needs.
HWE24VCN
ON/OFF
MODE
SPEED
TIMER
TEMP/TIME
TEMP/TIME
Press ON/OFF to turn on the air conditioner. Mode
Press MODE to choose Fan, Energy Save, Cool or Dehum. Speed Press SPEED to choose High, Med, Low or Auto Cool.
TIMER
To set the air conditioner to turn off after a set amount between 1 hour and 24 hours (unit must be ON):
1. rP ess TIMER. Timer OFF indicator light on the air conditioner control panel will flash.
2. rP ess the TEMP/TIME up or down arrow button to change the delay time from 1 hour to 24
hours.
3. retfA 5 seconds, Timer OFF indicator light on the air conditioner control panel will remain on.
TO SET TIMER TO TURN ON THE AIR CONDITIONER, KEEPING PREVIOUS SETTINGS:
1. Turn on the air conditioner.
2. rP ess TIMER. Timer On indicator light on the air conditioner control panel will flash
3. rP ess the TEMP/TIME up or down arrow button to change the delay time from 1 hour to 24
hours.
4. retfA 5 seconds, Timer On indicator light on the air conditioner control panel will remain on.
USING YOUR AIR CONDITIONER PAGE 25
ENGLISH
TO SET TIMER TO TURN ON THE AIR CONDITIONER, AND CHANGE THE PREVIOUS SETTINGS:
1. Turn on the air conditioner.
USING THE REMOTE CONTROL cont.
2. Adjust the mode to Fan, Energy Save, or Dehum.
3. roF Fan or Dehum mode,adjust the fan speed to High,Med or Low. For Cool or Energy Save mode,adjust the fan speed to High,Med, Low or Auto Cool.
NOTE:In Dehum mode,when the set temperature is close to the ambient temperature,the compressor may stop and the fan will run in low speed only.
4. Adjust the temperature between 61°F and 86°F (16°C and 30°C).
NOTE: In Fan mode, the temperature cannot be set.
5. rP ess TIMER. Timer On indicator light on the air conditioner control panel will flash. Display will show remaining hours before the air conditioner will turn on.
6. rP ess the TEMP/TIME up or down arrow button to change the delay time from 1 hour to 24 hours.
7. Timer On indicator light on the air conditioner control panel will remain on.
Cool
TO CLEAR TIMER DELAY PROGRAM:
NOTE: Air conditioner can be either on or off.
Press TIMER until Timer indicator light turns off.
TO SEE OR CHANGE THE REMAINING TIME (IN HOURS): TIMER OFF:
1. rP ess the TEMP/TIME up or down arrow button to increase or decrease the time.
2. retfA 5 seconds, the display on the air conditioner control panel will show will show the remaining time to Timer Off or the current room temperature.
TIMER ON:
1. Display on the air conditioner control panel will show remaining time.
2. rP ess the TEMP/TIME up or down arrow button to increase or decrease the time.
PAGE 26 USING YOUR AIR CONDITIONER
USING THE REMOTE CONTROL cont.
SLEEP
1. Press the TIMER button to choose Sleep mode. The indicator light will turn on.
2. The temperature will increase by 2˚F 1 hour after the mode is chosen. The temperature then increases another 2˚F after 1 hour. The unit will hold this temperature for 6 hours then stops.
3. To turn off Sleep mode, press the TIMER button until the indicator light is off.
TEMP/TIME
rP ess the TEMP/TIME up arrow button to raise the temperature. Each time you press the TEMP/
TIME up arrow button, the temperature will go up 1°F until it reaches 86°F (30°C).
rP ess the TEMP/TIME down arrow button to lower the temperature. Each time you press or
hold the TEMP/TIME down arrow button, the temperature will go down 1°F until it reaches 61°F (16°C).
ENGLISH
CHANGING THE AIR DIRECTION
The air directional louvers let you control the direction of the airflow. The airflow can be directed up-down or left to right.
Vent: The Fresh Air vent allows the air conditioner to recirculate inside air, draw fresh air into the
room, and exhaust stale air to the outside.
HWE15XCN,HWE18VCN
Fig. 33
4-Way Air Flow
Vent
(See
Fig.33 Fig.34)
4-Way Air Flow
HWE24VCN
Fig. 34
Vent
USING YOUR AIR CONDITIONER PAGE 27
ENGLISH
NORMAL SOUNDS
While your air conditioner is operating, it is normal to hear the following sounds:
Your new air conditioner is designed to give you many years of dependable service. This section tells you how to clean and care for your air conditioner properly.
NORMAL SOUNDS OF AN AIR CONDITIONER
SOUNDS REASON
Air movement Air rotating around the fan.
Window vibration Installation not correct. Refer to Install section
Pinging
High pitched hum The compressor turning on and off.
Clicking The thermostat turning on and off.
Gurgling Refrigerant moving through the evaporator (inside) coil.
Water droplets being thrown against the condenser (outside) coil. This
helps cool the condenser coil.
PAGE 28 USING YOUR AIR CONDITIONER
Loading...
+ 70 hidden pages