DWI 5212P
Domestic Dishwasher
DWI 5212P
GB
Code:0120504965
Safety Is a Good Habit to Get Into
GB
NOTICE
Carefully read the instructions contained in this manual, as they
provide important information which is essential to safe and
proper installation, use and maintenance of the appliance.
This appliance complies with the following EEC
directives:
- 73/23/EEC of 19/02/73 ( Low Voltage) and subsequent
modifications;
- 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and
subsequent modifications.
- Carefully dispose of the packing material.
- After removing the packing, check to make sure that the appli ance is not damaged. If in doubt, contact a qualified professional.
- The dishwasher must only be used by adults for the washing of
household dishes and cooking utensils.
- Fundamental rules to follow when using the appliance:
* Never touch the dishwasher when barefoot or with wet hands
or feet;
* We discourage the use of extension cords and multiple sock ets;
* During installation, the power supply cord must not be exces sively or dangerously bent or flattened;
* If the appliance is not operated properly or maintenance must
be performed, disconnect the appliance from the power supply.
Keep detergents out of the reach of children, who must also be
kept away from the dishwasher when it is open.
- This appliance cannot be installed outdoors, not even if the
area in which it is installed is covered by a roof; it is also very
dangerous to leave it exposed to the rain and elements.
- Do not touch the heating element during or after a wash cycle.
- Do not lean or sit on the door when it is open ,as this could
overturn the dishwasher.
- If the appliance malfunctions, turn off water supply to the appli ance and disconnect the plug from the wall socket. Then, con sult the section entitled, "Troubleshooting". If you cannot solve
the problem, contact a service center.
- Only specialized personnel are authorized to make repairs.
- Appliances which are no longer being used must be made inop erable by cutting the power supply cord and removing the door
lock.
Close-up View (control panel)
C
A
B
ON-OFF Button
ON-OFF Light
Cycle Select Button
C
Cycle Indicator Light
D
ABD
.1.
Close-up View (Interior)
GB
A
B
C
Upper Rack
A
Top Spray Arm
B
Lower Rack
C
Bottom Spray Arm
D
G
F
E
F
G
D
E
Washing Filter
Detergent and Rinse Aid Dispenser
Salt Container Cap
Width
Depth
Height
Capacity
Mains water pressure
Power voltage
Total absorber power
Technical characteristics
60 cm
58 cm
82 cm
12 standard place settings
0.03-0.6MPa
220-240V~ 50Hz
1950W
.2.
Salt
GB
Salt
The hardness of the water varies from place to place. If hard
water is used in the dishwasher, deposits will form on the dishes
and utensils.
The appliance is equipped with a special softener that uses a salt
specifically designed to eliminate lime and minerals from the water.
Loading the Salt into the Softener
Always use salt intended for use with dishwashers.
The salt container is located beneath the lower rack and should
be filled as follows:
- Remove the lower rack and then unscrew and remove the cap
from the salt container;
- If you are filling the container for the first time, fill it with water;
- Place the end of the funnel (supplied) into the hole and intro duce about 2 kg of salt. It is normal for a small amount of water
to come out of the salt container.
- Carefully screw the cap back on.
Adjusting Salt Consumption
The dishwasher is designed to allow for adjusting the amount of
salt consumed based on the hardness of the water used. This is
intended to optimize and customize the level of salt consumption
so that it remains at a minimum.
To adjust salt consumption, proceed as follows:
- Unscrew the cap from the salt container;
- There is a ring on the container with an arrow on it (see figure to
the side);
- If necessary, rotate the ring in an anti-clockwise direction from
the "-" setting towards the "+" sign, based on the hardness of
the water being used.
The salt container must be filled when the "low salt" indicator
light (located on the control panel), comes on..
To prevent the formation of rust, load the salt just before beginning a wash cycle.
It is recommended that adjustments be made in accordance
with the following schema:
Water Hardness
Salt
consumption
(Grams/cycle)
L
OM
QM
SM?H?
.3.
Clarke
Level
degrees
014 MNT
1
2
3
PSTN QRUV QIRUIV
4
mmol/l
ºdH
MNIT
NIUQIQNUQQNQPS
[UV[TN [UIV
Selector
position
=?J?
jba
Autonomy
(cycles/2kg)
LM
SM
QM
OR
Loading...