Haier DW12-EFM ME User Manual
Domestic Dishwasher
DW12-EFM ME
GB
Code: 0120505507
Safety Is a Good Habit to Develop
NOTICE
Carefully read the instructions contained in this manual, as
they provide important information which is essential for safe
and proper installation, use and maintenance of the appliance.
This appliance complies with the following EEC
directives:
- 73/23/EEC of 19 February 1973 (Low Voltage) and subse quent modifications;
- 89/336/EEC of 3 May 1989 (Electromagnetic Compatibility)
and subsequent modifications.
- Carefully dispose of the packing material.
- After removing the packing, check that the appliance is not
damaged. If in doubt, contact a qualified professional.
- The dishwasher must only be used by adults for the washing
of household dishes and cooking utensils.
- Fundamental rules to follow when using the appliance:
* Never touch the dishwasher when barefoot or with wet hands
or feet;
* We discourage the use of extension cords and multiple sockets;
* During installation, the power supply cord must not be
excessively or dangerously bent or flattened;
* If the appliance is not operating properly or maintenance must
be performed, disconnect the appliance from the power supply.
- Keep detergents out of the reach of children, who must also be
kept away from the dishwasher when it is open.
- This appliance cannot be installed outdoors, not even if the
area in which it is installed is covered by a roof; it is also very
dangerous to leave it exposed to the rain and elements.
- Do not touch the heating element during or after a wash cycle.
- Do not lean or sit on the door when it is open, as this could
overturn the dishwasher.
- If the appliance malfunctions, turn off the water supply to the
appliance and disconnect the plug from the wall socket. Then,
consult the section entitled, "Troubleshooting". If you cannot
solve the problem, contact a service centre.
- Only specialised personnel are authorised to make repairs.
- Appliances which are no longer being used must be made
inoperable by cutting the power supply cord and removing the
door lock.
- The appliance must be positioned so that the plug is accessible.
- The carpet must not obstruct the opening when the appliance is
installed on a carpeted floor.
- If the supply cord is damaged, it must be replaced by the
manufacture, its service agent of similarly qualified persons in
order to avoid a hazard.
Close-up View (control panel)
A
E
A
ON-OFF Light
Program Symbols
B
Cycle Select Knob
C
B
C
D
Handle For Opening Door
D
ON-OFF Button
E
.1.
GB
Close-up View (Interior)
H
G
A
B
C
D
E
F
Upper Rack
A
Rack Height Adjuster
B
Top Spray Arm
C
Lower Rack
D
Technical characteristics
Width
Depth
Height
Capacity
Mains water pressure
Power voltage
Bottom Spray Arm
E
Washing Filter
F
Detergent and Rinse Aid Dispenser
G
H
Salt Container Cap
12 standard place settings
220V-240V~ 50Hz
60 cm
60 cm
85 cm
0.03-0.6 MPa
Total absorber power
GB
2100W
.2.
Salt
Salt
The hardness of the water varies from place to place. If hard
water is used in the dishwasher, deposits will form on the dishes
and utensils.
The appliance is equipped with a special softener that uses a salt
specifically designed to eliminate lime and minerals from the water.
Loading the Salt into the Softener
Always use salt intended for use with dishwashers. The salt container is located beneath the lower rack and should be filled as
follows:
- Remove the lower rack and then unscrew and remove the cap
from the salt container;
- If you are filling the container for the first time, fill it with water;
- Place the end of the funnel (supplied) into the hole and intro
duce about 2 kg of salt. It is normal for a small amount of water
to come out of the salt container.
- Carefully screw the cap back on.
Adjusting Salt Consumption
The dishwasher is designed to allow for adjusting the amount of
salt consumed according to the hardness of the water used. This
is intended to optimise and customise the level of salt consumption so that it remains at a minimum.
To adjust salt consumption, proceed as follows:
- Unscrew the cap from the salt container;
- On the neck of the container there is a ring with an arrow on it
(see figure above). If necessary, turn the ring anti-clockwise
from the "-" sign towards the "+" setting, according to water
hardness.
- It is highly recommended that the following table be consulted
when making adjustments.
To prevent the formation of rust, load the salt just before beginning
a wash cycle.
Water Hardness
Clarke
degrees
MNQ
NQPS
PSTN
[TN
° dH
MNT
NUQQ
QRUV
[UV
mmol/l
MNIT
NIUQIQ
QIRUIV
[UIV
Selector
position
L
=?J?
MED
Salt
consumption
(Grams/cycle)
M
OM
QM
SM?H?
Autonomy
(cycles/2kg)
L
SM
QM
OR
.3.
GB
Loading...