Haier DW12-BFE ME User Manual

Domestic Dishwasher DW12-BFE ME

Code:0120503412

Safety Is a Good Habit to Get Into

NOTICE Carefully read the instructions contained in this manual,as they provide important information which is essential to safe and proper installation, use and maintenace of the appliance.

This appliance complies with the following EEC

directives:

-73/23/EEC of 19/02/73(Low Voltage)and subsequent modifications;

- 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications.

- Carefully dispose of the packing material.

- After removing the packing,check to make sure that the appli ance is not damaged.If in doubt,contact a qualified professional.

- The dishwasher must only be used by adults for the washing of household dishes and cooking utensils.

- Fundamental rules to follow when using the appliance: * Never touch the dishwasher when barefoot or with wet hands or feet; * We discourage the use of extension cords and multiple sockets; * During installation,the power supply cord must not be exces sively or dangerously bent or flattened; * If the appliance is not operating properly or maintenance must be performed, disconnect the appliance from the power supply.

- The appliance is not intended for use by young children or inform persons without supervision.

- Young children should be supervised to ensure that they do not play with the appliance.

- Keep detergents out of the reach of children,who must also be kept away from the dishwasher when it is open.

- This appliance cannot be installed outdoors,not even if the area in which it is installed is covered by a roof;it is also very dangerous to leave it exposed to the rain and elements.

- Do not touch the heating element during or after a wash cycle.

- Do not lean or sit on the door when it is open ,as this could over turn the dishwasher.

- If the appliance malfunctions,turn off water supply to the appli ance and disconnect the plug from the wall socket.Then,con sult the section entitled, "Troubleshooting".If you cannot solve the problem,contact a service centre.

- Only specialised personnel are authorised to make repairs.

- Appliances which are no longer being used must be made inoperable by cutting the power supply cord and removing the door lock.

- If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.

- After installation, the power plug must be accessible. To maintain the EFFICIENCY and SAFETY of this appliance,we recommend:

- call only the Service Centers authorized by the manufacturer.

- always use original Spare Parts.

Close-up View (control panel)

ON-OFF Button

ON-OFF Light

B C

Half-load Button

Half-load indicator light Delay select Button

Display delay time

G H I J K L

Cycle select button Cycle indicator light

Start/Pause button Low Rinse Aid Indicator Light Low Salt Indicator Light Handle For Opening Door

.1.

Close-up View (Interrior)

A B C D

Technical characteristics

Width

Depth

Height

Capacity

Mains water pressure Power voltage 220-240V~ 50Hz

Upper Rack Rack Height Adjustor Top Spray Arm Lower Rack

Bottom Spray Arm

Washing Filter

Detergent and Rinse Aid Dispenser

Salt Container Cap

Third Sprayer

12 standard place settings

60cm 60cm 85cm

0.03-0.6MPa

Total absorber power

2150W

.2.

Salt







Salt

The hardness of the water varies from place to place. If hard water is used in the dishwasher,deposits will form on the dishes utensils. The appliance is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the water.

Loading the Salt into the Softener

Always use salt intended for use with dishwashers. The salt container is located beneath the lower rack and should be filled as follows:

- Remove the lower rack and then unscrew and remove the cap from the salt container;

- If you are filling the container for the first time, fill it with water;

- Place the end of the funnel(supplied) into the hole and intro duce about 2 kg of salt.It is normal for a small amount of water to come out of the salt container.

- Carefully screw the cap back on.

Adjusting Salt Consumption

The dishwasher is designed to allow for adjusting the amount of salt consumed based on the hardness of the water used.This is intened to optimize and customize the level of salt consumption so that it remains at a minimum.Your local Water Board can supply the degree of hardness of the water in your area. To adjust salt consumption,proceed as follows:

- Unscrew the cap from the salt container;

- There is a ring on the container with an arrow on it (see figure to the side), If necessary, rotate the ring in the anticlockwise direction from the "-" setting towards the "+" sign,based on the hardness of the water being used. It is recommended that adjustments be made in accordance with the following scheme:

The salt container must be filled when the "low salt" indicator light (located on the control panel) comes on.

To prevent the formation of rust,load the salt just before beginning a wash cycle.

Water Hardness

Clarke degree

014

NQPS

PSTN

[TN

.3.

MNT

NUQQ

QRUV

[UV

mmol/l

MNIT

NIUQIQ

QIRUIV

[UIV

Selector position

=?J?

jba

?H?

Salt consumption (Grams/cycle)

Autonomy (cycles/2kg)

+ 8 hidden pages