Haier DW12-AFM3S User Manual
Domestic Dishwasher
DW12-AFM3
DW12-AFM3S
GB
=`çÇÉW=MNOMRMRNQO
Safety Is a Good Habit to Get Into
GB
NOTICE
Carefully read the instructions contained in this manual, as they
provide important information which is essential to safe and proper
installation, use and maintenance of the appliance.
This appliance complies with the following EEC
directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent
modifications;
- 89/336/EEC of 03/05/89 (Electromagnetic
Compatibility) and subsequent modifications.
- Carefully dispose of the packing material.
- After removing the packing, check to make sure that the appli ance is not damaged. If in doubt, contact a qualified professional.
- The dishwasher must only be used by adults for the washing of
household dishes and cooking utensils.
- Fundamental rules to follow when using the appliance:
* Never touch the dishwasher when bare foot or with wet hands
or feet;
* We discourage the use of extension cords and multiple sockets;
* During installation, the power supply cord must not be exces sively or dangerously bent or flattened;
* If the appliance is not operating properly or maintenance must
be performed, disconnect the appliance from the power supply.
- Keep detergents out of the reach of children, who must also be
kept away from the dishwasher when it is open.
- This appliance cannot be installed outdoors, not even if the
area in which it is installed is covered by a roof; it is also very
dangerous to leave it exposed to the rain and elements.
- Do not touch the heating element during or after a wash cycle.
- Do not lean or sit on the door when it is open, as this could
overturn the dishwasher.
- If the appliance malfunctions, turn off water supply to the appli ance and disconnect the plug from the wall socket. Then, con sult the section entitled, "Troubleshooting. "If you can not
solve the problem, contact a service centre.
- Only specialised personnel are authorised to make repairs.
- Appliances which are no longer being used must be made
inoperable by cutting the power supply cord and removing the
door lock.
- The appliance must be positioned so that the plug is accessible.
- The carpet must not obstruct the opening when the appliance in stalling on the ground with carpet.
- If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent of similarly qualified persons in
order to avoid a hazard.
Close-up View (Control Panel)
A B C
F
A
ON-OFF Light
B
ON-OFF Button
Low Salt Indicator Light
C
E
Knob For Selecting Cycle
D
Handle For Opening Door
E
"Eco" Button
F
D
.1.
Close-up View (Interior)
GB
Upper Rack
A
Rack Height Adjustor
B
C
Top Spray Arm
D
Lower Rack
Technical characteristics
Width
Depth
Height
Capacity
Mains water pressure
Power voltage
E
Bottom Spray Arm
F
Washing Filter
G
Detergent and Rinse Aid Dispenser
H
Salt Container Cap
12 standard place settings
220-240V~ 50Hz
60 cm
60 cm
85 cm
0.03-0.6 MPa
Total absorber power
2100W
.2.
Salt
GB
Salt
The hardness of the water varies from place to place. If hard
water is used in the dishwasher, deposits will form on the dishes
utensils.
The appliance is equipped with a special softener that uses a salt
specifically designed to eliminate lime and minerals from the water.
Loading the Salt into the Softener
Always use salt intended for use with dishwashers.
The salt container is located beneath the lower rack and should
be filled as follows:
- Remove the lower rack and then unscrew and remove the cap
from the salt container;
- If you are filling the container for the first time, fill it with water;
- Place the end of the funnel (supplied) into the hole and intro duce about 2 kg of salt. It is normal for a small amount of water
to come out of the container.
- Carefully screw the cap back on.
Adjusting Salt Consumption
The dishwasher is equipped with a system to adjust the level of
salt consumption in function of the hardness of the water being
used in order to optimize and customize the level of salt consumption while keeping it to a minimum.
To adjust salt consumption level, follow these instructions:
- Unscrew the cap on the salt container;
- On the container there is an arrow (see figure to the side). If
necessary, turn the arrow in the anti-clockwise direction from
the "-" setting to the "+" setting based on the hardness of the
water being used.
- It is highly recommended that the table be consulted when
making adjustments .
The salt container should be filled after about every 30 wash cycles.
To prevent the formation of rust, load the salt just before beginning a wash cycle.
Water Hardness
Clarke
degrees
014
NQPS
PSTN
[TN
.3.
dH
MNT
NUQQ
QRUV
[UV
mmol/l
MNIT
NIUQIQ
QIRUIV
[UIV
Selector
position
L
=?J?
jba
?H?
Salt
consumption
(Grams/cycle)
M
OM
QM
SM
Autonomy
(cycles/2kg)
L
SM
QM
OR
Loading...