HAIER AD362AMEAA, AD482AMEAA, AD282AMEAA, AD182AMEAA, AU362AIEAA User Manual [ru]

...

No. 0150502675

Please read this manual carefully before using this air conditioner

Please keep this manual safely for future use

DUCT TYPE 50Pa INDOOR UNIT

ON-OFF AD182AMEAA AD242AMEAA AD282AMEAA AD362AMEAA

INVERTER AD242AMERA AD282AMERA AD362AMERA

OPERATION MANUAL INSTALLATION MANUAL

MANUALE DI ISTRUZIONI MANUALE DI INSTALLAZIONE

MANUEL D’INSTRUCTIONS MANUEL D’INSTALLATION

BEDIENUNGSANLEITUNG INSTALLATIONSANLEITUNG

MANUAL DE INSTRUCCIONES MANUAL DE INSTALACIÓN

R410A UNITARY SMART

ON-OFF

AD482AMEAA

AD182AMEAA AD242AMEAA AD282AMEAA AD362AMEAA AD242AMERA AD282AMERA AD362AMERA AD482AMEAA

Tutti i prodotti sono conformi alle seguenti normative europee:

- Direttiva 73/23/EEC Basso Voltaggio

- Direttiva 2006/95/EC Basso Voltaggio

- Direttiva 89/336/EEC Compatibilità elettromagnetica

ROHS

Il prodotto è conforme alla normativa 2002/95/EEC sulla restrizione d’uso di sostanze inquinanti negli apparecchi elettrici ed elettronici.

WEEE

Informativa al consumatore come previsto dalla normativa europea 2002/96/CE riguardante i rifiuti di apparecchiature elettriche ed elettroniche.

SPECIFICHE DI SMALTIMENTO:

Il climatizzatore è contrassegnato con questo simbolo, ciò significa che i prodotti elettrici ed elettronici non possono essere smaltiti insieme ai rifiuti domestici non differenziati. Non cercare di demolire il sistema da soli: la demolizioni dei sistemi di condizionamento, nonché il recupero del refrigerante, dell’olio e di qualsiasi altra parte devono essere eseguiti da un installatore qualifi-

cato in conformità alla legislazione locale e nazionale vigente in materia.I climatizzatori devo essere trattati presso una struttura specializzata nel riutilizzo, riciclaggio e recupero dei materiali. Il corretto smaltimento del prodotto eviterà le possibili conseguenze negative all’ambiente e alla salute dell’uomo. Per maggiori informazioni contattare l’installatore o le autorità locali. Le batterie devono essere tolte dal telecomando e smaltite separatamente conformemente alla legislazione locale e nazionale vigente in materia.

CONFORMITÀ ALLE DIRETTIVE EUROPEE PER I MODELLI:

Haier Industrial Park, No.1 Haier Road, Qingdao, P.R.China

AD182AMEAA AD242AMEAA AD282AMEAA AD362AMEAA AD242AMERA AD282AMERA AD362AMERA AD482AMEAA

All the products are in conformity with the following European provision:

- Low Voltage Directive 73/23/EEC

- Low Voltage Directive 2006/95/EC

- Electromagnetic CompatibilitY 89/336/EEC

ROHS

The products are fulfilled with the requirements in the directive 2002/95/EEC of the European parliament and of the council on the Restriction of the use of Certain Hazardous Substances in Electrical and Electronic Equipment (EU RoHS Directive)

WEEE

In accordance with the directive 2002/96/CE of the European parliament, herewith we inform the consumer about the disposal requirements of the electrical and electronic products.

DISPOSAL REQUIREMENTS:

Your air conditioning product is marked with this sym-

bol. This means that electrical and electronic products

shall not be mixed with unsorted household waste.

Do not try to dismantle the system yourself: the dis-

mantling of the air conditioning system, treatment of

the refrigerant, of oil and of other part must be done

by a qualified installer in accordance with relevant

local and national legislation. Air conditioners must be treated at a specialized treatment facility for re-use, recycling and recovery. By ensuring this product is disposed of correctly, you will help to prevent potential negative consequences for the environment and human health. Please contact the installer or local authority for more information. Battery must be removed from the remote controller and disposed of separately in accordance with relevant local and national legislation.

EUROPEAN REGULATIONS CONFORMITY FOR THE MODELS:

AD182AMEAA AD242AMEAA AD282AMEAA AD362AMEAA AD242AMERA AD282AMERA AD362AMERA AD482AMEAA

Tous les produits sont conformes aux directives européennes suivantes:

- Directive 73/23/CEE Basse tension

- Directive 2006/95/CE Basse tension

- Directive 89/336/CEE Compatibilité électromagnétique

ROHS

L'appareil est conforme à la directive 2002/95/CEE relative à la limitation de l'utilisation de certains substances dangereuses dans les équipements électriques et électroniques.

DEEE (WEEE)

Information au consommateur comme le prévoit la directive européenne 2002/96/CE relative aux déchets d'équipements électriques et électroniques.

SPECIFICATIONS POUR L'ELIMINATION:

Ce pictogramme, apposé sur le climatiseur, signifie

que les équipements électriques et électroniques ne

peuvent pas être éliminés avec les déchets ménagers

non triés. Ne pas essayer de démanteler l'équipement

soi-même: le démantèlement des systèmes de clima-

tisation, ainsi que la récupération du frigorigène, de

l'huile et de toute autre partie doivent être effectués

par un installateur qualifié conformément à la législation locale et nationale en vigueur en la matière. Les climatiseurs doivent être traités dans un centre spécialisé dans la réutilisation, le recyclage et la valorisation des matériaux. L'élimination correcte de ces appareils permet d'éviter les effets nocifs sur l'environnement et la santé humaine. Pour plus de renseignements contacter l'installateur ou les autorités locales. Les piles doivent être retirées de la télécommande et éliminées séparément, conformément à la législation locale et nationale en vigueur en la matière.

CONFORMITÉ AUX DIRECTIVES EUROPÉENNES POUR LES MODÈLES:

Haier Industrial Park, No.1 Haier Road, Qingdao, P.R.China

AD182AMEAA AD242AMEAA AD282AMEAA AD362AMEAA AD242AMERA AD282AMERA AD362AMERA AD482AMEAA

Alle Produkte erfüllen die folgenden europäischen Richtlinien:

- Niederspannungsrichtlinie 73/23/EWG

- Niederspannungsrichtlinie 2006/95/EG

- EMV-Richtlinie 89/336/EWG

ROHS

Das Produkt erfüllt die Richtlinie 2002/95/EWG zur Beschränkung der Verwendung bestimmter gefährlicher Stoffe in Elektro- und Elektronikgeräten.

WEEE

Verbraucherinformation laut europäischer Richtlinie 2002/96/EG zu Elektround Elektronik-Altgeräten.

HINWEISE ZUR ENTSORGUNG:

Das Klimagerät ist mit diesem Symbol gekennzeich-

net, das darauf hinweist, dass Elektro- und Elektronik-

geräte getrennt vom Hausmüll entsorgt werden müs-

sen. Verschrotten Sie die Anlage nicht selbst: die Ver-

schrottung von Klimaanlagen, sowie die Rückgewin-

nung des Kältemittels, des Öls und aller sonstigen Tei-

le müssen durch einen qualifizierten Installateur in

Übereinstimmung mit den einschlägigen geltenden örtlichen und nationalen Vorschriften erfolgen. Die Klimageräte müssen bei einem Unternehmen entsorgt werden, das auf die Verwertung, das Recycling und die Rückgewinnung der Materialien spezialisiert ist. Die richtige Entsorgung des Produkts hilft negative Auswirkungen auf Umwelt und Gesundheit zu vermeiden. Für weitere Informationen wenden Sie sich bitte an den Installateur oder die örtlichen Behörden. Die Batterien müssen aus der Fernbedienung entfernt und in Übereinstimmung mit den einschlägigen geltenden örtlichen und nationalen Vorschriften getrennt entsorgt werden.

ÜBEREINSTIMMUNG MIT DEN EUROPÄISCHEN RICHTLINIEN FÜR DIE MODELLE:

AD182AMEAA AD242AMEAA AD282AMEAA AD362AMEAA AD242AMERA AD282AMERA AD362AMERA AD482AMEAA

Todos los productos están en conformidad con las siguientes Normativas Europeas:

- Bajo Voltaje directiva 73/23/EEC

- Bajo Voltaje directiva 2006/95/EC

- Compatibilidad electromagnética 89/336/EEC

ROHS

Los productos cumplen los requisitos de la directiva 2002/95/EEC del parlamento Europeo y el consejo regulador Del uso de materiales peligrosos en equipamientos eléctricos Y electrónicos. (EU RoHS Directiva).

WEEE

De acuerdo con la directiva 2002/96/CE del parlamento Europeo, Informamos al consumidor acerca del reciclage de los productos Electrónicos y eléctricos.

REQUISITOS PARA LA ELIMINACIÓN:

Su acondicionador de aire está marcado con este

símbolo. Esto significa que los productos eléctricos y

electrónicos no deben mezclarse con el resto de resi-

duos domésticos no clasificados.

No intente desmontar el sistema usted mismo: El des-

mantelamiento del acondicionador de aire, así como

el tratamiento del refrigerante, aceite y otros compo-

nentes, debe ser efectuado por un instalador competente de acuerdo con las normas locales y nacionales aplicables. Los acondicionadores de aire deben ser tratados en instalaciones especializadas para su reutilización, reciclaje y recuperación. Al asegurarse de desechar este producto de la forma correcta, està contribuyendo a evitar posibles consecuencias negativas para el entorno y para la salud de las personas. Contacte, por favor, con el instalador o con las autoridades locales para obtener más información. Las pilas del control remoto deben extraerse y eliminarse por separado y de acuerdo con la normativa local y nacional aplicable.

CONFORMIDAD EUROPEA DE LAS REGULACIONES PARA LOS MODELOS:

Questo prodotto contiene gas fluorurati ad effetto serra inclusi nel Protocollo di Kyoto. Non liberare tali gas nell’atmosfera.

Tipo di refrigerante: R410A Valore GWP*: 1975 *

GWP = potenziale di riscaldamento globale

Compilare con inchiostro indelebile,

• 1 la carica di refrigerante di fabbrica del prodotto

• 2 la quantità di refrigerante aggiuntiva nel campo e

• 1+2 la carica di refrigerante totale sull’etichetta di carica del refrigerante fornita con il prodotto

L’etichetta compilata deve essere collocata in prossimità della portata di carica del prodotto (ad esempio, nell’interno del coperchio della valvola d’intercettazione).

A contiene gas fluorurati ad effetto serra inclusi nel protocollo di Kyoto B carica di refrigerante di fabbrica del prodotto: vedi targhetta con il nome

dell’unità C quantità di refrigerante aggiuntiva nel campo D carica di refrigerante totale E unità esterna F cilindro del refrigerante e collettore di carica

INFORMAZIONI IMPORTANTI SUL REFRIGERANTE UTILIZZATO

Haier Industrial Park, No.1 Haier Road, Qingdao, P.R.China

This product contains fluorinated greenhouse gases covered by the Kyoto Protocol. Do not vent into the atmosphere.

Refrigerant type: R410A GWP* value: 1975 *

GWP = global warming potential

Please fill in with indelible ink,

• 1 the factory refrigerant charge of the product

• 2 the additional refrigerant amount charged in the field and

• 1+2 the total refrigerant charge on the refrigerant charge label supplied with the product.

The filled out label must be adhered in the proximity of the product charging port (e.g. onto the inside of the stop valve cover).

A contains fluorinated greenhouse gases covered by the Kyoto Protocol B factory refrigerant charge of the product: see unit name plate C additional refrigerant amount charged in the field D total refrigerant charge E outdoor unit F refrigerant cylinder and manifold for charging

IMPORTANT INFORMATION REGARDING THE REFRIGERANT USED

Ce produit contient des gaz à effet de serre fluorés encadrés par le protocole de Kyoto. Ne pas laisser les gaz s’échapper dans l’atmosphère.

Type de réfrigérant: R410A Valeur GWP*: 1975 *

GWP = potentiel de réchauffement global

Prière de compléter à l’encre indélébile,

• 1 la charge de réfrigérant d’usine du produit

• 2 la quantité de réfrigérant supplémentaire chargée sur place et

• 1+2 la charge de réfrigérant totale sur l’étiquette de charge de réfrigérant fournie avec le produit.

L’étiquette complétée doit être apposée à proximité de l’orifice de recharge du produit (par ex. à l’intérieur du couvercle de la vanne d’arrêt).

A contient des gaz à effet de serre fluorés encadrés par le protocole de

Kyoto B charge de réfrigérant d’usine du produit: voir plaquette signalétique de

l’unité C quantité de réfrigérant supplémentaire chargée sur place D charge de réfrigérant totale E unité extérieure F cylindre de réfrigérant et collecteur de recharge

INFORMATION IMPORTANTE RELATIVE AU RÉFRIGÉRANT UTILISÉ

Contains fluorinated greenhouse gases covered by the Kyoto Protocol

R410A

1+2=

Haier Industrial Park, No.1 Haier Road, Qingdao, P.R.China

Dieses Produkt enthält fluorierte Treibhausgase, die durch das Kyoto-Protokoll abgedeckt werden. Lassen Sie Gase nicht in die Atmosphäre ab.

Kältemitteltyp: R410A GWP* Wert: 1975 *

GWP = Treibhauspotential

Bitte füllen Sie am Kältemittelbefülletikett, das im Lieferumfang des Gerätes enthalten ist, mit abriebfester Tinte wie folgt aus:

• 1 die werkseitige Kältemittelbefüllung des Produktes

• 2 die am Montageort befüllte zusätzliche Kältemittelmenge und

• 1+2 die gesamte Kältemittelbefüllung

Das ausgefüllte Etikett muss in der Nähe der Kältemittel-Einfüllöffnung angehängt werden (z. B. auf der Innenseite der Absperrventilabdeckung).

A Enthält fluorierte Treibhausgase, die durch das Kyoto-ProtoKoll abge-

deckt werden B werkseitige Kältemittelbefüllung des Produktes: siehe Typenschild der

Einheit C zusätzliche am Montageort befüllen Kältemittelmenge D gesamte Kältemittelbefüllung E Außeneinheit F Kältemittelzylinder und Sammelleitung für die Befüllung

WICHTIGE INFORMATIONEN HINSICHTLICH DES VERWENDETEN KÄLTEMITTELS

Este producto contiene los gases fluorados de efecto invernadora regulados por el Protocolo de Kioto. No vierta gases a la atmósfera.

Tipo de refrigerante: R410A Valor GWP*: 1975 *

GWP = Potencial de calentamiento global

Rellene con tinta indeleble,

• 1 la carga de refrigerante de fábrica del producto

• 2 la cantidad adicional de refrigerante cargado en campo y

• 1+2 la carga total de refrigerante En la etiqueta de carga de refrigerante suministrada con el producto.

La etiqueta rellenada debe pegarse cerca de la conexión de carga del producto (p.ej. en el interior de la cubierta de la válvula de tope).

A Contiene los gases fluorados de efecto invernadora regulados por el

Protocolo de Kioto B Carga de refrigerante de fábrica del producto: véase placa de especifi-

caciones técnicas de la unidad C Cantidad adicional de refrigerante cargado en campo D Carga total de refrigerante E Unidad exterior F Cilindro del refrigerante y dosificador de carga

INFORMACIÓN IMPORTANTE EN RELACIÓN AL REFRIGERANTE UTILIZADO

Contains fluorinated greenhouse gases covered by the Kyoto Protocol

R410A

1+2=

DUCT TYPE AIR CONDITIONER

OPERATION MANUAL

INSTALLATION MANUAL

On-Off

AD182AMEAA AD242AMEAA AD282AMEAA AD362AMEAA

Inverter

AD242AMERA AD282AMERA AD362AMERA

On-Off

AD482AMEAA

Please read this operation manual before using the air conditioner. Please keep this manual carefully and safely.

Contents

Cautions

Safety Precautions

Parts and Functions

Operation

Heating Mode

Care and Maintenance

Troubleshooting

Precaution for Installation

Is The Unit Installed Correctly

Installation Procedure

Cautions

Disposal of the old air conditioner

Before disposing an old air conditioner that goes out of use, please make sure it's inoperative and safe. Unplug the air conditioner in order to avoid the risk of child entrapment.

It must be noticed that air conditioner system contains refrigerants, which require specialized waste disposal. The valuable materials contained in a air conditioner can be recycled. Contact your local waste disposal center for proper disposal of an old air conditioner and contact your local authority or your dealer if you have any question. Please ensure that the pipework of your air conditioner does not get damaged prior to being picked up by the relevant waste disposal center, and contribute to environmental awareness by insisting on an appropriate, anti-pollution method of disposal.

Disposal of the packaging of your new air conditioner

All the packaging materials employed in the package of your new air conditioner may be disposed without any danger to the environment.

The cardboard box may be broken or cut into smaller pieces and given to a waste paper disposal service. The wrapping bag made of polyethylene and the polyethylene foam pads contain no fluorochloric hydrocarbon.

All these valuable materials may be taken to a waste collecting center and used again after adequate recycling.

Consult your local authorities for the name and address of the waste materials collecting centers and waste paper disposal services nearest to your house.

Safety Instructions and Warnings

Before starting the air conditioner, read the information given in the User's Guide carefully. The User's Guide contains very important observations relating to the assembly, operation and maintenance of the air conditioner.

The manufacturer does not accept responsibility for any damages that may arise due to non-observation of the following instruction.

Damaged air conditioners are not to be put into operation. In case of doubt, consult your supplier.

Use of the air conditioner is to be carried out in strict compliance with the relative instructions set forth in the User's Guide.

Installation shall be done by professional people, don't install unit by yourself.

For the purpose of safety, the air conditioner must be properly grounded in accordance with specifications.

Always remember to unplug the air conditioner before opening inlet grill. Never unplug your air conditioner by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet.

All electrical repairs must be carried out by qualified electricians. Inadequate repairs may result in a major source of danger for the user of the air conditoiner.

Do not damage any parts of the air conditioner that carry refrigerant by piercing or perforating the air conditioner's tubes with sharp or pointed items, crushing or twisting any tubes, or scraping the coatings off the surfaces. If the refrigerant spurts out and gets into eyes, it may result in serious eye injuries.

Do not obstruct or cover the ventilation grille of the air conditioner. Do not put fingers or any other things into the inlet/outlet and swing louver.

Do not allow children to play with the air conditioner. In no case should children be allowed to sit on the outdoor unit.

Safety Precautions

Before starting to use the system, read carefully this "SAFETY PRECAUTIONS" to ensure a proper operation of the system. Safety precautions described here are classified to " WARNING" and " CAUTION". Precautions which are shown in the column of " WANING" means that an improper handing could lead to a grave result like a death, serious injury, etc. However, even if precautions are shown in the column of " CAUTION", a very serious problem could occur depending on situation. Make sure to observe these safety precautions faithfully because they are very important information to ensure the safety. Symbols which appear frequently in the text have following meanings.

Strictly prohibited.

Observe instructions faithfully.

Provide a positive grounding.

When you have read through the manual, keep it always at hand for read consultation. If the operator is replaced, make sure to hand over this manual to the new operator.

CAUTIONS FOR INSTALLATION

WARNING

The system should be applied to places as office, restaurant, residence and the like.

Application to inferior environment such as an engineering shop, could cause equipment malfunction and serious injury or death.

Do not install nearby the place where may have leakage of flammable gas.

If the gas leakes and gathers around, it may cause the fire.

Where strong winds may prevail, the system should be fixed securely to prevent a collapse.

The system should be installed by your dealer or a professional installer.

Installation by yourself is not encouraged because it could cause such problems as water leakage, electrical shock or fire accident by some improper handing.

CAUTION

Depending on the place of installation, a circuit breaker may be necessary.

OFF

Unless the circuit breaker is installed, it could cause elecrical shocks.

Install on the place where can endure the weight of air conditioner.

When you need some optional devices such as a humidifier, electric heater, etc., be sure to use the products which are recommended by us. These devices should be attached by a professional installer.

Installation by yourself is not encouraged because it could cause such problems as water leakage, electrical shock or fire accident by some improper handing.

Drain pipe should be arranged to provide a positive draining.

If the pipe is arranged improperly, furniture or the likes may be damaged by leaked water.

Make sure the system is grounded.

Bodily injury could result by a collapse. Bodily injury could result by a careless installation. Grounding cable should never be connected to

a gas pipe, city water pipe, lightning conductor rod or grounding cable of telephone. If the grounding cable is not set properly, it could cause electric shocks.

CAUTIONS FOR TRANSFER OR REPAIR

WARNING

Modification of the system is strictly prohibited. When the system needs a repair, consult your dealer.

Improper practice of repair could cause water leakage, electric shock or fire.

When the air conditioner is relocated, contact your dealer or a professional installer.

Improper practice of installation could cause water leakage, electric shock or fire.

Safety Precautions

CAUTIONS FOR OPERATION

You should refrain from exposing your body directly to cool wind for a long time.

WARNING

Do not poke the air inlet or outlet with a bar, etc. When any abnormal condition (scorching smell or

others) is found, stop the operation immediately and turn off the power switch. Then consult your dealer.

It could affect your physical condition or cause some health problems.

The system should never be used for any other purposes than intended such as for preservation of food, flora and fauna, precision devices or work of art.

problems.

Do not wash the air conditioner with water.

It could cause electric shocks. It will not be good for their health. Use of steel or copper wire in place of a fuse is

Neither stand on the air conditioner nor place something on it.

object.

Do not use the power switch to turn on or off the system.

It could cause a fire or water leakage. There is a risk of injury. If the system is operated at the vicinity of such

When operating the system simultaneously with a combustion apparatus, indoor air must be ventilated frequently.

OFF

Since the internal fan is operating with a high speed, it could cause an injury.

CAUTION

Do not handle switches with a wet hand. Combustion apparatus should not be placed

It could cause electric shocks.It could cause deterioration of food or other

Do not install the system where the air outlet reaches directly the flora and fauna.

It is strictly prohibited to place a container of combustible gas or liquid near the air conditioner or to spray it directly with the gas or liquid.

Do not touch the air outlet section while the swing louver is operating.

Check occasionally the support structure of the unit for any damage after a use of long period of time.

If you continue the operation without removing the cause, it could result in a trouble, electric shock or fire.

allowing a direct exposure to wind of air conditioner.

Incomplete combustion could occur on the apparatus.

Make sure to use a fuse of proper electric rating.

strictly prohibited because it could result in a trouble or fire accident.

Do not operate the system while the air outlet grill is removed.

There is a risk of injury.It could cause a fire accident.There are risks of falling or injury by collapsed

Do not use such equipment as a water heater, etc. around the indoor unit or the wire controller.

equipment which generates steam, condensed water may drip during cooling operation or it could cause a fault current or short-circuit.

When cleaning the system, stop the operation and turn off the power switch.

Insufficient ventilation could cause an oxygen deficiency accident.

Do not put water containers on the unit such as a flower vase, etc.

If the water enters into the unit and damages the electric insulation material, it may cause electric shock.

If the structure is not repaired immediately, the unit could topple down to cause a personal injury.

Cleaning should never be done while the internal fans are running with high speed.

Safety Precautions

The machine is adaptive in following situation

1. Applicable ambient temperature range:

ON-OFF Inverter 32/23 C 18/14 C 43/26 C 10/6 C

27 C 15 C

24/18 C

-7 C

Cooling

Heating

Indoor temperature

Outdoor temperature

Indoor temperature

Outdoor temperature

max. DB/WB min. DB/WB max. DB/WB min. DB/WB max. DB/WB min. DB/WB max. DB/WB min. DB/WB

2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person.

3. If the fuse on PC board is broken please change it with the type of T 3.15A /250VAC.

4. The wiring method should be in line with the local wiring standard.

5. The power cable should be:

H07RN-F 5G 4.0mm H07RN-F 5G 2.5mm H05RN-F 3G 6.0mm H05RN-F 3G 4.0mm H05RN-F 3G 2.5mm

The connecting cable should be: For series 182 , H05RN-F 3G 2.0mm

( For series 482(380-400V, 3N~, 50Hz));

( For series 362(380-400V, 3N~, 50Hz));

(For series 282,362 (1PH,220-230V~,50Hz));

(For series 242 (1PH,220-230V~,50Hz));

(For series 182 (1PH,220-230V~,50Hz));

+1X0.75mm

For the others, the connecting cable should be H05RN-F 4G 0.75mm All the cables shall have got the European authentication certificate. During installation, when the connecting cables break off, it must be assured that the grouding wire is the last one to be broken off.

6. The power cable and connect cable should be self-provided.

7. The breaker of the air conditioner should be all-pole switch, and the distance between its two contacts should be no less than 3mm.

8. The indoor unit installation height is at least 2.5m.

9. A leakage breaker must be installed.

32/23 C 18/14 C 43/26 C

-5 C 27 C 15 C

24/18 C

-7 C

Parts and Functions

For series 182, 242, 282, 362

For series 482

Air outlet

Duct

Air inlet

Air outlet

Duct

Air inlet

Parts and Functions

HEALTH

SET RECOVERY

CHECK

1.CLOCK button

Used to adjust time.

2.TIMER button

Used to set timer mode.

3.CHECK button

Auto-diagnostic button.

4.+ and - button

Stands for time plus/minus, used to adjust time.

5.FILTER button

Filter-cleaned button.

6.POWER ON/OFF button

Used for unit to start and stop.

8.FAN button

Used to select indoor air flow.

9.SWING button

Used for setting indoor swing mode.

10.HEALTH button

Used for setting indoor health function.

11.TEMP + and - button

Used for changing set temperature.

12.RECOVERY button

used to switch over air-exchanging mode.

13.RESET button

Reset correct mode button.

7.MODE button

Used to select indoor operation mode.

Note:

The above information is the explanation of the displayed information. Therefore it varies with those displayed in actual operation.

Cautions:

On cooling only unit, heating mode is not available.

The functions 5,9,10 are not available for these units.

Parts and Functions

HEALTH

SET RECOVERY

CHECK

[MODE] [AUTO]:Auto operation mode. [FAN ONLY]:Air-throwing mode. [COOL]:Cooling operation mode. [DRY]:Dehumidification mode. [HEAT]:Heating operation mode. [TES]:In heating mode, auxiliary electric heater is running.

Only when the unit with auxiliary electric heater is in auxiliary electric heating mode, it will display.

[FAN] [AUTO]:Auto fan running. [HIGH]:High fan speed. [MED]:Medium fan speed. [LOW]:Low fan speed. [FIX]:Fixed fan speed, it will display only when fixed fan

speed is requested to main indoor unit.

[CENTRAL]:Central control mode. [OPERATION]:Running mode. [STAND BY]: Waiting mode. [PRE-HEAT]: Pre-heating mode. [DEFROST]: Defrosting mode. [FILTER]: Request of filter to be cleaned. [HEALTH]:Health function. [CEN.ADD]:Central control address, the address number

will display on "88". [SYS.ADD.]:System address, the address number will display on "88".

[CHECK]:Auto-diagnostic, trouble shooting. [DEMAND]:Compulsory operation function, when it works,

[CENTRAL] will flash.

[SWING][MANUAL]:Swing mode. [ROOM TEMP.]:Indoor ambient temperature. [SET TEMP.]:Set admired temperature.

[TIMER] [ON]:Timer function is on. [OFF] :Timer function is off. [ON][OFF] :Timer function is ON-OFF. [ON][OFF][DAILY]:Timer ON-OFF will switch over in turn

daily.

[CLOCK]:Clock display, the displaying time is the current time of the clock.

[UP],[DOWN]:Indicator of filter elevating.

[VENTILATION] [AUTO]:Auto ventilation mode. [NORMAL]:Normal ventilation mode. [RECOVERY]:Fully heat exchanging ventilation mode.

Operation

Fan Only

(1)Start up operation:

Press the ON/OFF button. The system will start up and the

display will be on LCD.

(2)Select operation mode :

HEALTH

Press the MODE button. Each press, operation mode in

the [MODE] display section changes as follows:

SET RECOVERY

[FAN ONLY] [COOL] [DRY] [HEAT] [AUTO] [FAN ONLY]. Select [FAN ONLY].

CHECK

(3)Select fan speed:

1, 4

Press the FAN button. Each press, fan speed in the [FAN]

display section changes as follows:

[HIGH] [MED] [LOW] [HIGH]. Select proper fan speed.

(4)Power off:

Press the ON/OFF button. Indoor unit will be powered off, and there are only the time and the ambient temperature in the screen.

VENTILATION mode

(only for the unit with fresh air function or heat recovery function) Press the RECOVERY button, then the unit will switch over the ventilation mode: [ ] [VENTILATION][AUTO] [VENTILATION][RECOVERY] [VENTILATION][NORMAL] [ ] Please select appropriate ventilation mode.

Operation

Auto, Cool, Heat and Dry

(1) Start up operation:

Press the ON/OFF button. The system will start up and the

display will be on LCD.

(2) Select operation mode:

HEALTH

SET RECOVERY

CHECK

Press the MODE button. Each press, operation mode in

the [MODE] display section changes as follows:

[FAN ONLY] [COOL] [DRY] [HEAT] [AUTO] [FAN ONLY]. Select operation mode ([COOL],[DRY],[HEAT],or [AUTO]).

(3) Set temperature:

Press the TEMP + or - button. Each press, setting

1, 7

temperature will increase or decrease by 1 C ( F). [SET

TEMP.] appears on the display.

(4) Select fan speed:

Press the FAN button. Each press, fan speed in the [FAN]

display section changes as follows:

[AUTO] [HIGH] [MED] [LOW] [AUTO]. Select proper fan speed.

(5) Select SWING function:

Press the SWING button once, [SWING] will display and swing function is valid. Press again, [SWING] will disappear and swing function is invalid.

(6) Set HEALTH operation:

Press the HEALTH button to set the indoor health function. Press it once, [HEALTH] will display in the display section, and indoor health function is valid. Press it again, [HEALTH] will disappear, and the health function is invalid. This function is valid only for the unit with health function.

(7) Power off:

Press the ON/OFF button. Indoor unit will be powered off, and there are only the time and the ambient temperature in the screen.

Operation

Timer Function

Clock set

Before setting timer mode, set the clock to the correct time. Press the CLOCK button. "CLOCK" will begin flashing at the frequency of 2Hz. Press the clock +/- button to adjust the current time. Then press the SET button to confirm until the proper time comes.

TIMER ON operation:

TIMER OFF operation:

TIMER ON-OFF operation:

Press the TIMER button. Each time the button is pressed, TIMER mode in the [TIMER] display section changes as follows: [ON] [OFF] [ON][OFF] [ON][OFF][DAILY] [ ]. Select [TIMER] [ON] [OFF], and then [TIMER][ON] flashes. Press the clock +/- button to adjust the time of TIMER ON, and then press the TIMER button to confirm. [TIMER][ON] will be constant on and [TIMER] [OFF] flashes. Press the clock +/- button to adjust the time of TIMER OFF, and press the SET button to confirm. The time sequence of timer on and timer off will determine the mode is [TIMER] [ON] [OFF] or [TIMER] [OFF] [ON]. If you want the current time, press the CLOCK button once, current time will display; Press again, [CLOCK] will flash, and press clock + / - button to adjust the time.

Note:

If the two times are the same, the timer state which is set later will flash, in this case, timer can not be set. When entering TIMER setting state, if you do not input any button in continuous 10

2. seconds, the unit will quit from the TIMER mode.

Cancel TIMER operation:

In the timer operation state, press the TIMER button, the unit will quit from the current timer operation state, and the set data will be memorized, then enter the next timer mode. When [TIMER] does not display, the timer will be cancelled.

Operation

Query indoor malfunction history:

In the state of power on or power off, press the CHECK button to enter the malfunction-querying mode of all indoor units in the group. Then [CHECK] and [UNIT NO.] will display, and the actual indoor numbers will be displayed in some sequence (unit number is in decimals). At the same time, in the time region, there will be the current malfunction and the latest time malfunction, the displaying format is [XX:YY], in which XX stands for the current malfunction, if normal, it will display "--"; YY stands for the latest time malfunction. The failure code of every unit will display for 3 seconds. After the failure codes of all indoor units in the whole group are displayed, the mode will quit automatically.

Heating Mode

"HOT KEEP" function

"HOT KEEP" is operated in the following cases.

When heating is started: In order to prevent blowing out of cool wind, the indoor unit fan stopped according to the room temperature which heating operation is started. Wait for approx. 2 to 3 minute, and the operation will be automatically changed to the ordinary heating mode. Defrosting operation (in the heating mode): When it is liable to frost, the heating operation is stopped automatically for 5 to 12 minutes once per approx. one hour, and defrosting is operated. After defrosting is completed, operation mode is automatically changed to ordinary heating operation. When the room thermostat is actuated: When room temperature increases and room temperature controller actuates, the fan speed is automatically changed to stop under low temperature condition of indoor heat exchanger. When room temperature decreases, air conditioner automatically changes over to ordinary heating operation.

Warming operation

Heat pump type warming With the heat pump type warming, the mechanism of heat pump that concentrate heat of outdoor air with the help of refrigerant to warm the indoor space, is utilized. Defrosting operation When a room is warmed with a heat pump type air conditioner, frost accumulates on the heat exchanger of outdoor unit along with the drop of indoor temperature. Since the accumulated frost reduces the effect of warming, it is necessery to automatically switch the operation to the defrosting mode. During the defrosting operation, heating operation is interrupted. Atmospheric temperature and warming capacity Warming capacity of heat pump type air conditioner decreases along with the drop of outdoor temperature. When the warming capacity is not sufficient, it is recommended to use another heating implement. Period of warm-up Since the heat pump type air conditioner employs a method to circulate warm winds to warm the entire space of a room, it takes time before the room temperature rises. It is recommendable to start the operation a little earlier in a very cold morning.

Care and Maintenance

Points to observe

Turn off the power supply switch. Do not touch with wet hand. Do not use hot water or volatile liquid.

Do not use!

Benzine Tooth powder

OFF

CAUTION

Do not open the inlet grill until fan stops completely. Fan will continue rotating for a while by the law of inertia after operation is being stopped.

Cleaning the air filter

1.Clean the air filter by lightly tapping it or with the cleaner. It is more effective to clean the air filter with water. If the air filter is very dirty, dissolve neutral detergent in the lukewarm water (approx. 30 C), rinse the air filter in the water, and thoroughly wash the air filter off the detergent in the plain water.

2.After drying the air filter, set it up on the air conditioner.

Thinner

CAUTION

Do not dry the air filter with fire. Do not run the air conditioner without the air filter.

Care and Cleaning of the unit

Clean with soft and dry cloth. If it is very dirty, dissolve neutral detergent in the lukewarm water and make the cloth wet with the water. After wiping, clean off the detergent using clean water.

Post-Season Care

Operate the unit with FAN mode on a fair day for about half a day to dry the inside of the unit well. Stop operation and turn off the power supply switch. Electric power is consumed even the air conditioner is in stop. Clean the air filter and set it in the place.

Pre-Season Care

See that there are no obstacles blocking the air inlet and air outlet of both indoor and outdoor units. Make sure that the air filter is not dirty. Cut in the power supply switch 12 hours before starting run.

Troubleshooting

Please check the following things about your air conditioner before making a service call.

Unit fails to start

Is the power source switch adjust cut in?

OFF

Power supply switch is not ON.

Is city supply power in normal?

Power stoppage?

Cooling or heating is not sufficient

Isn't the signal receiving section exposed to the direct sunlight or strong illumination?

Isn't the earth leakage breaker in action?

It is dangerous. Turn off the power supply switch immediately and contact the sales dealer.

Is the thermostat adjust as required?

Isn't the air filter dirty? Isn't any doors or windows

left open?

Doesn't any obstacle exist at the air inlet or outlet?

Isn't the swing louver horizontal? (At HEATING mode) If swing louver is horizontal, the blow wind does not reach floor.

Cooling is not sufficient

Isn't sun-shine invading direct? Isn't any unexpected heating

load generated?

Isn't the room much crowded?

The wind does not blow during heating operation

Isn't it warming up?

When the air conditioner does not operate properly after you have checked the above mentioned items or when the following phenomenon is observed, stop the operation of the air conditioner and contact your sales dealer.

The fuse or breaker often shuts down. Water drops off during cooling operation. There is a irregularity in operation or abnormal sound is audible. When the CHECK LED (red) flickers, an irregularity has occurred in the air conditioner.

Troubleshooting

The followings are not malfunction

Water flowing sound is heard.

Shuru

When the air conditioner is started, when the compressor starts or stops during operation or when the air conditioner is stopped, it sometimes sounds "shuru shuru" or "gobo gobo". It is the flowing sound of the refrigerant, and it is not a trouble.

This is caused by heat expansion or contraction of plastics.Cracking sound is heard.

It smells. Air which blows out from the indoor unit sometimes smells. The smell results

from residents of tobacco smoke or cosmetics stuck inside of unit.

During operation, white fog comes out of indoor unit.

When the air conditioner is used at restaurant etc. where dense edible oil fume is always exists, white fog sometimes blows out of air outlet during operation. In this case consult sales dealer for cleaning the heat exchanger.

It is switched into the FAN mode during cooling.

To prevent frost from being accumulated on the indoor unit heat exchanger, it is sometimes automatically switched to the FAN mode,but it will soon return to the cooling mode.

The air conditioner can not be restarted soon after it stops.

Unit does not start

Even if the operation switch is turned on, cooling, dehumidifying or heating is not operable for three minutes after the conditioner is stopped. Because the protecting circuit is activated. (During this time air conditioner operates in fan mode.)

Wait for three minutes

Air does not blow or the fan speed can not be changed during dehumidifying.

During operation, operation mode has changed over automatically.

Water or steam generates from the outdoor unit during heating.

When it is excessively cooled during dehumidifying, the blower automatically repeats reducing and lowering the fan speed.

Isn't the AUTO mode selected? In the case of AUTO mode, operation mode is changed automatically from cooling to heating or vise-versa according to the room temperature.

This results when frost accumulated on the outdoor unit is removed (during defrosting operation).

Troubleshooting

Diagnosis for inverter models

Remarks

Resumable

if lower than

100 degree

Reason

Sensor broken down or short circuit for more than 2m continuously

CT check abnormal 3 times in 30m

Failure description

Indoor ambient temp. sensor failure

Indoor coil temp. sensor failure

Outdoor ambient temp. sensor failure

Outdoor coil temp. sensor failure

Over-current protection

Failure code

for central control

01D

02D

11D

12D

10D

Fault phase, short of phase, out of balance greatly

High pressure switch acts 3 times in 30m

High pressure abnormal

14D

Communication abnormal for more than 4m continuously

Power supply abnormal

Communication between wired controller

and indoor abnormal

22D

06D

Communication abnormal for more than 4m continuously

Float switch broken down for more than 25m continuously

Outside signal broken down for more than 10s

Sensor broken down or short circuit for more than 2m continuously

Solenoid valve act incorrectly 3 times continuously

Sensor broken down or short circuit for more than 2m continuously

EEPROM data missing

Low pressure switch acts in normal running

The discharging temperature is higher than 120degree

Communication between indoor and outdoor abnormal

Drainage system abnormal

Outside alarm signal input

Gas pipe temp. sensor abnormal

Temperature protection malfunction

Discharging temp. sensor abnormal

EEPROM abnormal

Pressure abnormal(low pressure)

Compressor overheat

05D

21D

30D

20D

31D

15D

17D

26D

15D

Indoor operation mode is different with the running indoor unit.

Sensor broken down or short circuit for more than 2m continuously

Spdu module temperature is too high

Outdoor DC motor abnormal or cooling & heating abnormal

Abnormal mode

Outdoor coil B(suction temp sensor-for MRV II)

Outdoor discharging B(oil temp sensor-for MRV II)

SPDU module temperature protection

Outdoor DC motor failure or system failure

23D

18D

15D

07D

08D

01(01H)

02(02H)

74(4AH)

73(49H)

72(48H)

83(53H)

71(47H)

07(07H)

06(06H)

Failure code

on wired controller

Flash times

for remote type

shows resumable fault, shows it is not resumable fault.

08(08H)

11(0BH)

03(03H)

13(0DH)

76(4CH)

05(05H)

84(54H)

80(50H)

12(0CH)

75(4BH)

77(4DH)

20(32D)

36(54D)

Troubleshooting

Diagnosis for On-Off models

Remarks

Resumable

if lower than

100 degree

Sensor broken down or short circuit for more than 2m

continuously

Sensor broken down or short circuit for more than 2m

continuously

Sensor broken down or short circuit for more than

2m continuously

Sensor broken down or short circuit for more than

2m continuously

CT check abnormal 3 times in 30m / Fault phase,

short of phase,out of balance greatly

Failure description Reason

Indoor ambient temp. sensor failure

Indoor coil temp. sensor failure

Outdoor ambient temp. sensor failure

Outdoor coil temp. sensor failure/ Compressor

discharging temp. sensor abnormal

Over-current protection / Power supply

abnormal

Failure code

for central control

01D

02D

11D

12D

10D

High pressure switch acts 3 times in 30m/Low pressure

switch acts in normal running

Communication abnormal for more than 4m continuously

Float switch broken down for more than 25m continuously

Outside signal broken down for more than 10s

Sensor broken down or short circuit for more than 2m

continuously

Solenoid valve act incorrectly 3 times continuously

High/Low pressure abnormal

Communication between wired controller and

indoor abnormal

Communication between indoor and outdoor

abnormal

Drainage system abnormal

Outside alarm signal input

Gas pipe temp. sensor abnormal

Temperature protection malfunction

EEPROM abnormal

14D

06D

05D

21D

30D

20D

31D

17D

EEPROM data missing

The discharging temperature is higher than 120degree

Indoor operation mode is different with the running

indoor unit.

Sensor broken down or short circuit for more than 2m

continuously

Sensor broken down or short circuit for more than 2m

continuously

Compressor overheat

Abnormal mode

Outdoor coil B(suction temp sensor-for MRV II)

Outdoor discharging B(oil temp sensor-for

MRV II)

15D

23D

18D

15D

Failure code

on wired controller

01(01H)

02(02H)

74(4AH)

73(49H)

72(48H)

83(53H)

07(07H)

06(06H)

Flash times

for remote type

shows resumable fault, shows it is not resumable fault.

08(08H)

11(0BH)

03(03H)

13(0DH)

05(05H)

80(50H)

12(0CH)

75(4BH)

77(4DH)

Precaution for Installation

Please read these "Safety Precautions" first and then accurately execute the installation work. Though the precautionary points indicated herein are divided under two headings, and , those points which are related to the strong possibility of an installation done in error resulting in death or serious injury are listed in the section. However, there is also a possibility of serious consequences in relationship to the points listed in the section as well. In either case, important safety related information is indicated, so by all means, properly observe all that is mentioned. After completing the installation, along with confirming that no abnormalities were seen from the operation tests, please explain operating methods as well as maintenance methods to the user (customer) of this equipment, based on the owner's manual. Moreover, ask the customer to keep this sheet together with the owner's manual.

This system should be applied to places as office, restaurant, residence and the like. Application to inferior environment such as engineering shop could cause equipment malfunction. Please entrust installation to either the company which sold you the equipment or to a professional contractor. Defects from improper installations can be the cause of water leakage, electric shocks and fires. Execute the installation accurately, based on following the installation manual. Again, improper installations can result in water leakage, electric shocks and fires. When a large air-conditioning system is installed to a small room, it is necessary to have a prior planned countermeasure for the rare case of a refrigerant leakage, to prevent the exceeding of threshold concentration. In regards to preparing this countermeasure, consult with the company from which you perchased the equipment, and make the installation accordingly. In the rare event that a refrigerant leakage and exceeding of threshold concentration does occur, there is the danger of a resultant oxygen deficiency accident. For installation, confirm that the installation site can sufficiently support heavy weight. When strength is insufficient, injury can result from a falling of the unit. Execute the prescribed installation construction to prepare for earthquakes and the strong winds of typhoons and hurricanes, etc. Improper installations can result in accidents due to a violent falling over of the unit. For electrical work, please see that a licensed electrician executes the work while following the safety standards related to electrical equipment, and local regulations as well as the installation instructions, and that only exclusive use circuits are used. Insufficient power source circuit capacity and defective installation execution can be the cause of electric shocks and fires. Accurately connect wiring using the proper cable, and insure that the external force of the cable is not conducted to the terminal connection part, through properly securing it. Improper connection or securing can result in heat generation or fire. Take care that wiring does not rise upward, and accurately install the lid/service panel. Its improper installation can also result in heat generation or fire. When setting up or moving the location of the air conditioner, do not mix air etc. or anything other than the designated refrigerant (R410A) within the refrigeration cycle. Rupture and injury caused by abnormal high pressure can result from such mixing. Always use accessory parts and authorized parts for installation construction. Using parts not authorized by this company can result in water leakage, electric shock, fire and refrigerant leakage.

WARNING

CAUTION

WARNING

CAUTION

Execute proper grounding. Do not connect the ground wire to a gas pipe, water pipe, lightning rod or a telephone ground wire. Improper placement of ground wires can result in electric shock. The installation of an earth leakage breaker is necessary depending on the established location of the unit. Not installing an earth leakage breaker may result in electric shock. Do not install the unit where there is a concern about leakage of combustible gas. The rare event of leaked gas collecting around the unit could result in an outbreak of fire. For the drain pipe, follow the installation manual to insure that it allows proper drainage and thermally insulate it to prevent condensation. Inadequate plumbing can result in water leakage and water damage to interior items.

Is The Unit Installed Correctly

Confirm the following items for safe and comfortable use of air conditioner. The installation work is to be burden on the sales dealer, and do not conduct it by yourself.

Installation place

Avoid installing the air conditioner near the place where possibility of inflammable gas leakage exists.

Explosion (Ignition) may occur.

Select the place so as not to annoy neighbor with the hot air or noise.

Install the unit at well ventilated place.

capacity reduction or noise increase.

Snow protection work is necessary where outdoor unit is blocked up by snow.

For details consult your sales dealer.

Install the air conditioner firmly on the foundation that can fully support the weight of the unit.

If not, it may cause vibration or noise.If some obstacle exist, it may cause

It is advisable not to install the air conditioner at the following special place. It may cause malfunction, consult the sales dealer when you have to install the unit on such a place.

The place where corrosive gas generates (Hot spring area etc.) The place where salt breeze blows (Seaside etc.) The place where dense soot smoke exists The place where humidity is extraordinarily high The place where near the machine which radiates the electromagnetic wave The place where voltage variation is considerably large

Electric work

The electric work must be burden on the authorized engineer with qualification for electric work and grounding work, and the work must be conducted in accordance with electric equipment technical standard.

The power source for the unit is to be of exclusive use. An earth leakage breaker should be installed.(This is necessary to prevent electric shock.) The unit must be grounded.

When you change your address or the installation place

Special technology is required for removal or reinstallation of air conditioner, consult the sales dealer. Besides, construction expense is charged for removal or reinstallation.

For inspection and maintenance

The capacity of air conditioner will decrease by contamination of inside of unit when it is used for about three years although depending upon the circumstances under which it is used, and so in addition to the usual maintenance service, special inspection/maintenance service is necessary. It is recommended to make a maintenance contract (charged) by consulting your sales dealer.

Installation Procedure

Wiring connections of wired controller

Wired controller Wired controller Wired controller Wired controller Wired controller

Wired Controller

Indoor 16Indoor 15Indoor NIndoor 2Indoor 1

(master unit)

1 2 3 1 2 3 1 2 3 1 2 3 1 2 3

Indoor 1

Wired controller

Poler wire

Wired controller

1 2 3

A B C

Indoor 1

Wired controller

Poler wire

Wired controller

1 2 3

Poler wire

A B C

Wired controller

Control wiring of wired controller, polar.

A B C

Wired controller

There are three methods to connect wired controller and the indoor units: A.One wired controller can control max. up to 16 sets of indoor units. In this case, 3 pieces of polar wire must connect the wired controller and the master unit (the indoor unit connected with wired controller directly), the others connect with the master unit through 2 pieces of polar wire. B. One wired controller controls one indoor unit. The indoor unit connects with the wired controller through 3 pieces of polar wire. C. Two wired controllers control one indoor unit. The wired controller connected with indoor unit is called master one, the other is called slave one. Master wired controller and indoor unit; master and slave wired controllers are all connected through 3 pieces of polar wire.

Note:

The method A needs to set the PCB function switch. The method C needs to set the controller function switch.

Communication wiring

The wired controller is equipped with special communication wiring in the accessories. 3-core terminal (1-white 2-yellow 3-red) is connected with the terminal A, B, C of wired controller respectively.

The communication wiring is 4 meter long. If the actual length is more than it, please distribute wiring according to below table:

Communication wiring length(m) Dimensions of wiring

< 100 0.3mm

100 and <200 0.5mm

200 and <300 0.75mm

300 and <400 1.25mm

400 and <600 2mm

x 3-core shielded wire

*One side of the shielded sheet of communication wire must be earthed.

Installation Procedure

Indoor Unit

NOTE

All wiring of this installation must comply with NATIONAL, STATE AND LOCAL REGULATIONS. These instructions

do not cover all variations for every kind of installation circumstance. Should further information be desired or should particular problems occur, the matter should be referred to your local distributor.

WARNING

BE SURE TO READ THESE INSTRUCTIONS CAREFULLY BEFORE BEGINNING INSTALLATION. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD CAUSE SERIOUS INJURY OR DEATH, EQUIPMENT MALFUNCTION AND/OR PROPERTY DAMAGE.

Preparation of indoor unit

Before or during the installation of the unit, assemble necessary optional panel etc. depending on the specific type.

Select places for installation satisfying following conditions and at the same time obtain the consent on the part of your client user.

Places where chilled or heated air circulates freely. When the installation height exceeds 3m warmed air stays close to the ceiling. In such cases, suggest your client users to install air circulators.

Places where perfect drainage can be prepared and sufficient drainage.

Places free from air disturbances to the suction port and blowout hole of the indoor unit, places where the fire alarm may not malfunction or short-circuit.

Places with the environmental dew-point temperature is lower than 28 and the relative humidity is less than 80 %.

C (When installing at a place under a high humidity environment, pay sufficient attention to the prevention of dewing such as thermal insulation of the unit. )

Ceiling height shall have the following height.

Installation space

For series 482 For series 182 242 282 362

Combination with silent panel

416mm

366mm

100mm 100mm

50mm

1000mm

Obstacle

Avoid installation and use at those places listed

Places exposed to oil splashes or steam (e.g. kitchens and machine plants). Installation and use at such places incur deteriorations in the performance or corrosion with the heat exchanger or damage in molded synthetic resin parts.

Places where corrosive gas (such as sulfurous acid gas) or inflammable gas (thinner, gasoline etc.) in generated or remains. Installation and use at such places cause corrosion in the heat exchanger and damage in molded synthetic resin parts. Places adjacent to equipment generating electromagnetic waves or high-frequency waves such as in hospitals.

Generated noise may cause malfunctioning of the controller.

Pipe size

Model

AD182AMEAA

Liquid side Gas side

6.35mm 12.7mm

AD242AMEAA AD282AMEAA AD242AMERA

9.52mm 15.88mm

AD282AMERA AD362AMERA AD362AMEAA AD482AMEAA

9.52mm 19.05mm

Installation Procedure

1. Preparation for suspending the unit

a.Size of hole at ceiling and position of hanging

Pipe connection

side

545

690

750

Ceiling hole size

Hanging bolt position

Indoor Unit

Panel dimensions

Hanging bolt position

Model

Ceiling hole size

Panel dimensions

Dimensions

For series 182 242 282 362

For series 482

137

Ceiling ~ panel wrap dimensions

1000mm 1194mm 1254mm

1406mm 1600mm 1660mm

Ceiling ~ panel

wrap dimensions

b.Hanger bolts installation

Use care of the piping direction when the unit is installed.

2.Installation of indoor unit

Fix the indoor unit to the hanger bolts. If required, it is possible to suspend the unit to the beam, etc. Directly by use of the bolts without using the hanger bolts.

Note

When the dimensions of main unit and ceiling holes does not match, it can be adjusted with the slot holes of hanging bracket.

Hole-in anchor Hole-in plug

Hanging bolt M10

M10 nut

Main unit

Insert

Concrete

Hanging bolt

M10 washer

M10 spring washer

Adjusting to the levelness

(a) Adjust the out-of levelness using a level or by the following method.

Make adjustment so that the relation between the lower surface of the unit proper and water level in the hose becomes as given below.

(b) Unless the adjustment to the levelness is made properly, malfunctioning or failure of the float switch may occur.

Tap selection on blower unit

(When the high performance filter is used.)

Taps of blower unit are set at the standard selection at the shipping from factory. Where the static pressure is raised by employing such option as the high performance filter, etc., change the connection of connectors provided at the flank of control box as shown below.

Piping side

Supply water

Water level

0~5 mm

(0~0.2")

Standard tap (at shipping) High speed tap

White

Blue

Yellow

Red

Control box side

Bring the piping side slightly lower.

Moter side

White

Blue

Yellow

Red

White

Blue

Yellow

White

Red

Connector white

PVC hose

Black

White

Blue

Red

Moter side

Installation Procedure

Drain Pipe

Drain Piping

(a)

Drain piping should always be in a downhill grade (1/50~1/100) and avoid riding across an elevation or making traps.

Improper pipingGood piping

Suspension bolts

Heat insulation

1.5m ~ 2m

Air vent

A downhill grade of 1/100 or more

Avoid riding across an elevation

Keep free from traps

Do not pipe under water

When connecting the drain pipe to unit, pay suffcient attention

(b)

not to apply excess force to the piping on the unit side. Also, fix the piping at a point as close as possible to the unit.

For drain pipe, use hard PVC general purpose pipe VP-25(I.D.1")

(c)

which can be purchased locally. When connecting, insert a PVC pipe end securely into the drain socket before tightening securely using the attached drain hose and clamp. Adhesive must not be used for connection of the drain socket and drain hose (accessory).

When constructing drain piping for several units, position the

(d)

common pipe about 100 mm below the drain outlet of each unit as shown in the sketch. Use VP-30(11/4") or thicker pipe for this purpose.

The hard PVC pipe put indoor side should be heat insulated. Do

(e)

not ever provide an air vent.

Drain socket

Main unit

Pipe cover(large) [for insulation] (accessory)

Drain hose

(accessory) Clamp (accessory)

Pipe cover(small) [for insulation] (accessory)

Secure the elevation as high as possible (approx. 100 mm)

A downhill grade of 1/100 or more

Drain socket

Adhesion

Stage difference part

VP-25 joint (field purchased)

VP-25 (field purchased)

Pipe cover [for insulation] (field purchased)

VP-30

Drain hose

The height of the drain head can be elevated up to a point 500

(f)

mm above the ceiling, and when an obstacle exists in the ceiling space, elevate the piping to avoid the obstacle using an elbow or corresponding gadget. When doing this, if the stretch for the needed height is higher than 500 mm, the back-flow quantity of drain at the event of interruption of the operation gets too much and it may cause overflow at the drain pan. Therefore, make the height of the drain pipe within the distance given in the sketch below.

Avoid positioning the drain piping outlet at a place where generation

(g)

of odor may be stimulated. Do not lead the drain piping direct into a sewer from where sulfur gas may generate.

290~325mm

Drain hose

Right overhead

600

(Maximum local drain up dimension)

Joint for VP-25 (Local procurement)

+ 116 hidden pages