Page 1
Haier
SERVICE MANUAL
LED TV
Model No. 40D3505
MSD3393LU
Chassis
WARNING
This service information is designed for experienced repair technicians only and is not designed for use by the general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair
the product or products dealt with in this service information by anyone else could result in serious injury or death.
©2013 Qingdao Haier Electronics Co., Ltd.
All rights reserved. Unauthorized copying and distribution is a violation of law.
Page 2
Service Manual
Model No.: 40D3505
CONTENTS
Chapter 1. General Information
1-1. Document Information ..............................................................3
1-2. General Guidelines.....................................................................3
1-3. Important Notice.........................................................................3
1-3-1. Follow the regulations and warnings ..................................................... 3
1-3-2. Be careful to the electrical shock ............................................................3
1-3-3. Electro static discharge (ESD)............................................................... .3
1-3-4. About lead free solder (PbF)...................................................................4
1-3-5. Use the genewing parts (specified parts) .............................................. 4
1-3-6 Safety check after repairment................................................................. 4
1-3-7. Ordering Spare Parts............................................................................. 6
1-3-8. Photo used in this manual .....................................................................6
1-4. How to Read this Service Manual ............................................6
Using icons ...............................................................................................................6
Chapter 2. Specification
2-1. Specification list.........................................................................8
2-2. External pictures (four faces)....................................................9
Chapter 3. Disassemble and Assemble
3-1. 40D3505 .................................................................................11
3-1-1. Remove the Stand.................................................................................11
3-1-2. Remove the Back Cabinet ....................................................................11
3-1-3. Remove the Mainboard.........................................................................11
3-1-4. Remove the Power Supply Module ......................................................11
3-1-5. Remove the Speaker.............................................................................11
3-1-6. Remove the Remote Control Board .....................................................12
3-1-7. Remove the Key Board.........................................................................12
Chapter 4. Location of Controls and Components
4-1. Board Location .........................................................................13
4-2. Mainboard .................................................................................14
4-2-1. Function Description .............................................................................14
4-2-2. Connector definition ..............................................................................14
4-3. Power Supply Module ..............................................................15
4-3-1. Function Description .............................................................................15
1
Page 3
Service Manual
Model No.: 40D3505
4-3-2. Connector definition ..............................................................................15
4-4. LCD Panel ..................................................................................16
Chapter 5. Installation Instructions
5-1. Accessories ..............................................................................18
5-2. External Equipment Connections............................................19
Chapter 6. Operation Instructions
6-1. Front Panel Controls.................................................................20
6-2. Back Panel Controls .................................................................21
6-3. Setting Up Your Remote Control .............................................22
Chapter 7. Electrical Parts
7-1. Block Diagram............................................................................23
7-2. Circuit Diagram..........................................................................30
Chapter 8. Measurements and Adjustments
8-1. Service Mode ............................................................................31
8-1-1.How to enter into Service Mode............................................................ 31
8-1-2.How to exit ............................................................................................31
8-2. Measurements and Adjustments ............................................31
8-2-1. The Main Menu ....................................................................................31
8-2-2. General Setting ....................................................................................32
8-2-3. Picture ..................................................................................................32
8-2-4. Sound................................................................................................... 33
8-2-5. Debug...................................................................................................33
8-3. Software Update ......................................................................34
8-3-1. T.VST59 software update ....................................................................34
Chapter 9. Trouble shooting
9-1. Simple check ...........................................................................35
9-2. Mainboard IC Introduction......................................................38
9-3. Mainboard Failure Check........................................................39
9-4. Pannel Failure..........................................................................45
2
Page 4
Service Manual
Model No.: 40D3505
Chapter 1. General Information
1-1. Document Information
Document format: Adobe PDF
Author: shouwang.wen
Compiler:
1-2. General Guidelines
When servicing, observe the original lead dress. If a short circuit is found, replace all parts which
have been overheated or damaged by the short circuit.
After servicing, see to it that all the protective devices such as insulation barriers, insulation papers
shields are properly installed.
After servicing, make the following leakage current checks to prevent the customer from being
exposed to shock hazards.
1) Leakage Current Cold Check
2) Leakage Current Hot Check
3) Prevention of Electro Static Discharge (ESD) to Electrostatically Sensitive
1-3. Important Notice
1-3-1. Follow the regulations and warnings
Most important thing is to list up the potential hazard or risk for the service personnel to open
the units and disassemble the units. For example, we need to describe properly how to avoid the
possibility to get electrical shock from the live power supply or charged electrical parts (even the
power is off).
This symbol indicates that high voltage is present inside.It is dangerous to make any
king of contact with any inside part of this product.
This symbol indicates that there are important operating and maintenance instructions
in the literture accompanying the appliance.
1-3-2. Be careful to the electrical shock
To prevent damage which might result in electric shock or fire, do not expose this TV set to rain
or excessive moisture. This TV must not be exposed to dripping or splashing water, and objects
filled with liquid, such as vases, must not be placed on top of or above the TV.
1-3-3. Electro static discharge (ESD)
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such
3
Page 5
Service Manual
Model No.: 40D3505
components commonly are called Electrostatically Sensitive (ES) Devices. The following
techniques should be used to help reduce the incidence of component damage caused by
electros static discharge (ESD).
Electrostatically Sensitive (ES) Devices
Some semiconductor (solid-state) devices can be damaged easily by static electricity. Such
components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical
ES devices are integrated circuits and some field-effect transistors and semiconductor "chip"
components. The following techniques should be used to help reduce the ncidence of component
damage caused by static by static electricity.
1. Immediately before handling any semiconductor component or semiconductor-equipped
assembly, drain off any electrostatic charge on your body by touching a known earth ground.
Alternatively, obtain and wear a commercially available discharging wrist strap device, which
should be removed to prevent potential shock reasons prior to applying power to the unit under
test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a
conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of
the assembly.
1-3-4. About lead free solder (PbF)
This product is manufactured using lead-free solder as a part of a movement within the
consumer products industry at large to be environmentally responsible. Lead-free solder must be
used in the servicing and repairing of this product.
1-3-5. Use the genewing parts (specified parts)
Special parts which have purposes of fire retardant (resistors), high-quality sound (capacitors),
low noise (resistors), etc. are used.
When replacing any of components, be sure to use only manufacture's specified parts shown in
the parts list.
Safety Component
● Components identified by mark have special characteristics important for safety.
1-3-6 Safety check after repairment
Confirm that the screws, parts and wiring which were removed in order to service are put in the
original positions, or whether there are the positions which are deteriorated around the serviced
places serviced or not. Check the insulation between the antenna terminal or external metal and
the AC cord plug blades. And be sure the safety of that.
General Servicing Precautions
4
Page 6
Service Manual
Model No.: 40D3505
1. Always unplug the receiver AC power cord from the AC power source before:
a. Removing or reinstalling any component, circuit board module or any other receiver
assembly.
b. Disconnecting or reconnecting any receiver electrical plug or other electrical connection.
c. Connecting a test substitute in parallel with an electrolytic capacitor in the receiver.
CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors
may result in an explosion hazard.
2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage
measuring device (DVM, FETVOM, etc) equipped with a suitable high voltage probe.
Do not test high voltage by "drawing an arc".
3. Do not spray chemicals on or near this receiver or any of its assemblies.
4. Unless specified otherwise in this service manual, clean electrical contacts only by applying
the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable nonabrasive applicator; 10% (by volume) Acetone and 90% (by volume) isopropyl alcohol (90%-99%
strength).
CAUTION: This is a flammable mixture.
Unless specified otherwise in this service manual, lubrication of contacts is not required.
Capacitors may result in an explosion hazard.
5. Do not defeat any plug/socket B+ voltage interlocks with which receivers covered by this
service manual might be equipped.
6. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all
solid-state device heat sinks are correctly installed.
7. Always connect the test receiver ground lead to the receiver chassis ground before connecting
the test receiver positive lead.
Always remove the test receiver ground lead last. Capacitors may result in an explosion
hazard.
8. Use with this receiver only the test fixtures specified in this service manual.
CAUTION: Do not connect the test fixture ground strap to any heat sink in this receiver.
9. Remove the antenna terminal on TV and turn on the TV.
10. Insulation resistance between the cord plug terminals and the eternal exposure metal should
be more than Mohm by using the 500V insulation resistance meter.
11. If the insulation resistance is less than M ohm, the inspection repair should be required.
If you have not the 500V insulation resistance meter, use a Tester. External exposure metal:
Antenna terminal Headphone jack.
5
Page 7
Service Manual
Model No.: 40D3505
12. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
13. Use only an anti-static type solder removal device. Some solder removal devices not
classified as "anti-static" can generate electrical charges sufficient to damage ES devices.
14. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to
damage ES devices.
15. Do not remove a replacement ES device from its protective package until immediately
before you are ready to install it.
(Most replacement ES devices are packaged with leads electrically shorted together by
conductive foam, aluminum foil or comparable conductive material).
16. Immediately before removing the protective material from the leads of a replacement ES
device, touch the protective material to the chassis or circuit assembly into which the device will
be installed.
CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety
precautions.
17. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise
harmless motion such as the brushing together of your clothes fabric or the lifting of your foot
from a carpeted floor can generate static electricity sufficient to damage an ES device.)
1-3-7. Ordering Spare Parts
Please include the following informations when you order parts. (Particularly the Version letter)
1. Model number, serial number and software version
The model number and serial number can be found on the back cover of each product. Software
version can be found in the Spare Parts List.
2. Spare part No. and description
Spare part No. and description can be found in the Spare Parts List.
1-3-8. Photo used in this manual
The illustration and photos used in this Service Manual may not base on the final design of
products, which may differ from your products in some way.
1-4. How to Read this Service Manual
Using icons
Icons are used to attract the attention of the reader to specific information. The meaning of each
icon is described in the table below:
Note:
A “note” provides information that is not indispensable, but may nevertheless be
valuable to the reader, such as tips and tricks.
6
Page 8
Service Manual
Model No.: 40D3505
Caution:
A “caution ” is used when there is danger that the reader, through incorrect
manipulation, may damage equipment, loose data, get an unexpected result or has to
restart(part of) a procedure.
Warning:
A “warning” is used when there is danger of personal injury.
Reference:
A “reference” guides the reader to other places in this binder or in this manual, where
he/she will find additional information on a specific topic.
7
Page 9
Model
40D3505
Screen Size
40"
Aspect Ratio
16:9
Resolution
1920x1080
Brightness (cd/m²)
280
Contrast
1500:1
Response Time (ms)
8
Angel of View
H:170°, V:160°
Color Display
16.7M
OSD Language
English,French,Spanish.
Color System
NTSC/ATSC
Audio System
MN
Audio Output Power (Built-in) (W)
8W×2
Audio Output Power (outer) (W)
No
Total Power Input (W)
100W
Voltage Range (V)
AC100V~240V
Power Frequency (Hz)
50~60Hz
Time of Sleep Timer (MINS)
240Min
Net Weight (KG)
6.85
Gross Weight (KG)
8.70
Net Dimension (MM)
883.86*548.05*248.5
Packaged Dimension (MM)
972*604*156
Service Manual
Model No.: 40D3505
Chapter 2. Specification
2-1. Specification list
8
Page 10
Service Manual
Model No.: 40D3505
2-2. External pictures (four faces)
Front Side
Up Side
9
Page 11
Service Manual
Model No.: 40D3505
Right Side
Back Side
10
Page 12
Service ManualModel No.: 39D3005
Model NO.:40D3505
Chapter 3. Disassemble and Assemble
3-1. 40D3505
3-1-1. Remove the Stand
1. Lay down the TV set .
2. Remove the four screws from the stand which
in the picture above.
3. Remove the stand.
3-1-2. Remove the Back Cabinet
1.Remove the fifteen screws indicated with red
circles.
2. Flip machine, panel side up.
3.Carefully raise the Front shell from
bottom.
3-1-3. Remove the power-main board.
1. Remove the six screws indicated with red circles.
2. Then remove the side metal board and down metal board.
3. Remove the four screws indicated with red circles.
4. Remove the power-main board.
3-1-4. Remove the Speaker
Remove the speaker directly
11
Page 13
Service Manual
Model No.: 40D3505
3-1-6. Remove the Remote Control Board And the Key Board
Remove the Remote Control Board and the Key Board indicated byred circle in below picture.
12
Page 14
A Board
B Panel
No.
Parts number
Description
A Board
DH1TK3M0100M
power-main board
B Panel
712-39583-X3250
LCD Panel
Service Manual
Model No.: 40D3505
Chapter 4. Location of Controls and Components
4-1. Board Location
13
IR & Key Interface
Page 15
CN6
Pin number
Signal name
1
GND
2
K7 3 K6
4
K5
5
K4 6 K3 7 K2 8 K1 9 K0
10
GND
11
IR
12
GRE
13
RED
14
5V
LED Backlight interface
CN804/CN805
Pin number
Signal name
1
LED+
2
NC
3
LED-
Speaker connector CN20
Pin number
Signal name
1
ROUT+
2
ROUT-
3
LOUT-
4
LOUT+
Service Manual
Model No.: 40D3505
4-2. Mainboard
4-2-1. Function Description
Process signal which incept from exterior equipment then translate into signal that panel can
display.
4-2-2. Connector definition
14
Page 16
Service Manual
Model No.: 40D3505
15
Page 17
Service Manual
Model No.: 40D3505
4-3. LCD Panel
40D3505
Backlight Unit
LVDS CONNECTOR CNF1
16
Page 18
Service Manual
Model No.: 40D3505
17
Page 19
Chapter 5. Installation Instructions
5-1. Accessories
18
Service Manual
Model No.: 40D3505
Remote Control
Batteries
Page 20
Service Manual
Model No.: 40D3505
5-2. External Equipment Connections
Antenna Connection
Connect your aerial to the back of the TV into the
ANTENNA IN socket.
Improve Your Signal
To improve picture quality in a poor signal area, use a
signal amplifier (not supplied).
Connect Your PC to the TV
You can use your TV as a monitor for your personal
computer by connecting it with a VGA cable (not
supplied).
Read your computer user guide and check it has a
A
VGA connector.
Turn off your TV and PC.
B
Connect a D type 15-pin VGA interface cable to the
C
VGA video interface connector on the PC. Connect
the other end of the cable to the PC interface
connector on the TV. Tighten the screws on the
VGA connectors and connect the audio cable (not
supplied) to the audio input socket on the back of the
TV.
Turn on the TV firstly and then the PC.
D
Press the Source button on the TV or TV remote
E
control to set the video input mode to PC.
Once the image shows, if there is noise present,
F
change the PC mode to other resolutions, change the
refresh rate to other rate or adjust the brightness and
contrast on the menu until the picture is clear.
Connect a DVD Player to Your TV
Connect the DVD video outputs (Y, Pb, Pr) to the
COMPONENT (Y, Pb, Pr) IN socket on your TV.
Turn on the DVD player and insert a DVD disk.
A
Press the SOURCE button to select COMPONENT
B
mode.
Refer to the DVD player user guide for operating
C
instructions.
Connect a DVD Player or VCR to
Your TV
There are two ways in which you can connect a DVD
player or VCR to your TV. Make sure that both the TV
and DVD player or VCR are switched off before you
connect them.
HDMI Input
A
Connect the cable from the HDMI device to the TV
HDMI socket.
Press the SOURCE button to select HDMI mode.
B
Refer to the HDMI device user guide for how to
C
operate.
19
Page 21
1 POWER
Press to turn the TV on and off.
2
CH-
TV channel down.
3
CH+
TV channel up.
4
VOL-
Press to decrease
the volume.
5 VOL+
Press to increase
the volume.
6 MENU
Press to select the main menu.
7 INPUT
Press to select the input source.
Service Manual
Model No.: 40D3505
Chapter 6. Operation Instructions
6-1. Front Panel Controls
20
Page 22
9 10 11 12
1 2 3 4 5 6 7 8
1
Earphone
output
2
Coax
output
3
Audio in
input
4
Video/Y in
input
5
PbPr IN
input
6
PC Audio
input
7
VGA
input
8
RF
input
9
HDMI1
input
10
HDMI2(MHL)
input
11
HDMI3(ARC)
input
12
USB IN
input
6-2. Back Panel Controls
Service Manual
Model No.: 40D3505
21
Page 23
Service Manual
Model No.: 40D3505
6-3. Setting Up Your Remote Control
When using the remote control, aim it towards the remote sensor on the TV.
1 2
3
4 5
21
6
7
8 9
10 11
12 13
14 16
15 17
18 19
20
21 22
23 24
25 26
22
POWER.
1
INPUT.
2
USB
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Shortcut button.
CC.
HOME;
Program Number Channel selection.
RECALL button.
VOL+/VOL-: Volume selection
CH∧/CH∨: Channel selection.
Mute.
Menu button.
Back button.
Exit button.
DISPLAY button.
SAP button.
Sleep button.
Wide button.
Audio button.
Picture Mode.
OK button.
Channel List.
Favorite program.
Play / Pause button (only for USB).
EPG button.
Fast Reverse (only for USB).
Fast Forward (only for USB).
.
Page 24
Service Manual
Model No.:40D3505
Chapter 7. Electrical Parts
7-1. Circuit Diagram
Page 25
Page 26
Page 27
Page 28
Page 29
Page 30
Page 31
7-2 . Wiring Connection Diagram
Model No.: 40D3505
Service Manual
30
Page 32
Service Manual
Model No.: 40D3505
Chapter 8. Measurements and Adjustments
8-1. Service Mode
8-1-1.How to enter into Service Mode
The way to the factory mode menu:
Step 1: Press Menu,
Step 2: Press “8893”,
System will be into the factory mode menu when 2 steps above are done.
At the end of the main factory menu, you can see the edition of the software,
like this" BUILD TIME 2014-01-21 23:17:21
VERSION v1.0 ”.
8-1-2.How to exit
If you want to exit this factory menu, please press the button ”Exit” on the remote.
system will be out the factory mode menu.
8-2. Measurements and Adjustments
8-2-1. The Main Menu
In factory mode menu,press up/down
button to choose the up/down item,press
right or OK button to the submenu.press
MENU button to go back.
31
Page 33
Service Manual
Model No.: 40D3505
8-2-2. GENERAL SETTING
1)Init Flash;
2)Uart Enable:Choose on or off in Uart Enable;
3)Dbg Message Enable: Choose on or off in
Dbg Message Enable;
4)Test Pattern: Choose the Pattern picture;
5)Dynamic Contrast: Choose on or off in
Dynamic Contrast;
6)Power On Mode:Choose on or off in Power
On Mode;
7)Mirror Control: Choose on or off in Mirror
Control;
8)Front End Status
9)Timer Test
10)SSC
11)Erase Flash
12)PQ Advance Debug: Choose on or off in
PQ Advance Debug;
13)Factory remote:Open or close the
Factory remote;
14)Factory CH Export.
8-2-3. PICTURE
Adjust the Picture Mode,Picture Curve,
White Balance and OverScan in different
source.
32
Page 34
8-2-4. SOUND
Adjust the values of Sound Mode,
Volume Curve,Audio Output and True Volume
in different source.
8-2-5. Panel Setting
1)LVDS Bit Mode: choose the Bit;
2)LVDS MAP: choose the MAP;
3)LVDS ODD/Even: choose ODD or Even;
4)Bcaklight:Adiust the value of backlight;
5)Reset Panel Setting Date
6)6MX0 LVDS Map: choose the 6MX0 LVDS MAP;
7) 6MX0 Channel: choose the 6MX0 Channel;
8)6MX0 Mirror: choose the 6MX0 Mirror;
9)6MX0 Demo: choose the 6MX0 Demo;
10)6MX0 Update.
33
Service Manual
Model No.: 40D3505
Page 35
Service Manual
Model No.: 40D3505
8-3. Software Update
8-3-1. MSD3393LU software update
1. Copy the software files to a USB disk on the root directory;
2. Insert the USB disk when the AC power is off;
3. Turn on the AC power in turn to begin;
4. Turn off the AC power until the indicator light fast twinkling;
5. Pull out the USB disk and power on the television.
Note:
Do not turn off the TV while it is updating.
34
Page 36
No picture/ No sound
Verify if the television is properly plugged
Verify if the television is properly supplied power
Verify if electricity is available.
Blank screen
Verify if correct signals are input
Press SOURCE button to change signal input to TV
input
Restart the television of power supply is interrupted
No sound
Press the MUTE button and verify that Mute mode is
active.
Switch to another channel to check whether the same
problem occurs.
Press the VOL+ button to see if the problem can be
solved.
Poor sound
Verify that the sound system is correct. Refer to the
user manual for instructions on how to adjust it.
No picture on some channel
Verify if correct channel is selected.
Adjust the antenna.
Make adjustments by Fine Tune and MANUAL Scan.
No color for some channel
program (black and white)
Verify that the same problem exists on other channels.
Check the picture and sound systems.
Refer to the relevant instructions in the manual to
adjust the colour.
Spots with some or all pictures
Verify if the antennal is correctly connected.
Verify if the antennal is in good condition.
Make fine adjustment of channel.
Television is not working
Disconnect the television from the power supply for
10 seconds, then reconnect the television. If the
problem persists, contact an authorised after-sales
service provider for technical assistance.
Television out of control
Disconnect the television from power supply and 10
seconds later, connect the television to the power
supply. If the problem still exists, contact authorized
after-sales service for technical assistance.
Chapter 9. Trouble shooting
9-1. Simple check
35
Service Manual
Model No.: 40D3505
Page 37
1
2
3
4
5
6
7
8
Service Manual
Model No.: 40D3505
9-2. Mainboard IC Introduction
Top view
36
Page 38
Service Manual
Model No.: 40D3505
Bottom view
37
Page 39
Service Manual
Model No.: 40D3505
1.Mainchip—MSD3393LU(U1)
2. Audio Amplifier—TPA3110D2PWPR (UA1)
3.Main Flash Memory—GD25Q32BSIG (UF1)
4.DC/DC convertor 5V-1.8V for MSD3393LU (U1)—LC1117CLTRAD (UL2)
5.voltage convertor 5V to 3.3V_STB —LC1117CLTR33 (UL1)
6.voltage convertor 5V to 1.15V_STB —LC3406CB5TR (UD1)
7.voltage convertor 5V to 3V for tuner—LC1117CLTR33 (UT1)
8.Tuner —SDCL1005CR33JTDF (RFT1)
Please check the Schematic Diagram for the particular support
38
Page 40
Service Manual
Model No.: 40D3505
9-3. Mainboard Failure Check
No picture but have sound
Check the power output
Yes
Check the CN2 (BLO)
Backlight on/off
No
No
Change the Power Board
There’s something wrong
with FRC
Yes
Verify if the DC/DC
convertor can output the
right Voltage,
No
Change the corresponding
DC/DC
QB3 output 5V
Yes
No
Verify if QM1
Change the QM1
output
Yes
Still having
Change Panel
problems
Change LVDS wire
39
Page 41
you connect.
Yes
Service Manual
Model No.: 40D3505
No sound but have picture
Verify if the speakers are
broken
No
Verify if the main board has the
right input ,according to the source
TV/COMPONENT/AV/VGA/HDMI etc.
Verify if UA1 has the right
output
Yes
Check CN17 input is right
Still having problems
Yes
No
Change Mainboard
No
Change the speakers
Check the corresponding audio
input circuit you connect.
Verify if UA1 has the right power in
No
Change UA1
40
Page 42
Service Manual
Model No.: 40D3505
No sound No picture
No
41
Verify if the Power has
5Vstb output
Yes
Verify if CN4 Pin3/4 has 5V
input
Yes
Verify if CN2 Pin1 has 12V
input
Yes
Verify if DC/DC convertors have
the right output
Yes
Change the software
No
No
No
Change the
Power supply
Change Power board
Change Power board
Change corresponding
DC/DC convertor
Still having
Problems
Change
Mainboard
Page 43
Service Manual
Model No.: 40D3505
Poor sound
Poor sound
Verify if sound system is
correct .
No
Change sound
system
For ease of use, recommend that customer format the picture and
sound settings in the automatic option.
Still having
problems
Updata the software and
make the reboot; or
change the maiboard
42
Page 44
Service Manual
Model No.: 40D3505
No color for some channel program (black and white)
No color for some chann
el program (black and w
hite)
Verify if the same
problem exists in other
channels
Yes
check out of picture
and sound system
No
No
Check out of picture and sound
system of this channel
Change the channel to the right sound
system (PAL-BG SECAM/L)
43
Yes
Refer to relative
instructions in the
Manual for color adjust
Still having
problems
Updata the software and
make the reboot; or
change the maiboard
Page 45
Service Manual
Model No.: 40D3505
How to know whether the Power board is broken?
Check if the power cord co
nnect well?
Yes
Check if the Power board
No
No
Reconnect the power cord with the
outlet or Power board.
Replace the Power board pls.
output 5V and 12V ?
Still having
problems
Check if Main board / LVDS wire / Panel are in
good condition
44
Page 46
Part
Block Defect :TCP cracking or cracking
Dim or L/D :TCP Sunken
:TCP lead cracking
:ACF bonding short
:Awful environment and
something electric enter
into LCD
:Mis-align between TCP and
Panel
:Panel failure
:TCP failure
Name
Description
Phenomena
Failure cause
V B/D
Vertical bar
V Dim
Vertal gray line
V L/D
Vertical color line(light or
dark forever)
TCP
H B/D
Horizontal bar
H Dim
Horizontal gary line
H L/D
Horizontal line(light or
dark forever)
45
9-4. Pannel Failure
Failure Mode
Model No.: 40D3505
Service Manual
Page 47
Description
Phenomena
Failure Cause
Bright dot dark dot in pannel
Incoming Inspection Standard
Bladder in Polarizer
Bladder between Polarizer and
top glass
Polarizer Scratch
Tine or rigidity arose
Eyewinker inside Polarizer
Eyewinker inside Polarizer
Abnormal Display
Bright and dark display alternately
1.Chip lose action
2.IC ahort or jointiog bad
3.Pannel and vsc connect bad
Part
Name
Dot Defect
Polarizer Bubble
Panel or Polarlzer
Polarizer Scratch
F/inside Polarizer
Abnormal Display
Circuit
Flashing
Model No.: 40D3505
Service Manual
46
Page 48
Part
Name
Description
Phenomena
Failure Cause
White Screen
B/L normal,
only white screen display
Maybe caused by surge current and EDS
Black Screen
B/L normal,
only Black screen display
Circuit
Crosstalk
FIIcker
LCD
Vcom imbalance
Abnormal Color
Only
color abormal
Capacitance
improper bring crosstalk inside LCD pannel
Abnormal Color
Only
color abnormal
1.Chip
lose action
2.IC short or jointion bad
3.Pannel and vsc connect bad
47
Model No.: 40D3505
Service Manual
Page 49
Description
Caused
by Mechanica noise of backlight unit
Part
Name
Phenomena
Failure cause
Mechanlcal
Nolse
When
turn panel,appear cacophony
Ripple
Connectric circle
Causeed by
between
mechanism and pannel
B/L off
B/L lose action
*Connect
badness
between wire and electrode
B/L dark
B/L brightness darker than
normal
*Connect
badnessShort between wire and electrode
B/L
wire damaged
Without backlight
B/L
wire damaged
B/L wire open
Operation
abnormal
or systemic noise
Operation
abnormal
or systemic noise
Short bitween lamp housing and wire, Because
consume power too much
B/L shut down
B/L shutdown in sometime
F/M
F/M
inB/L ,white,balck Rotundity
or wirelike
F/M in B/L unit
Model No.: 40D3505
Service Manual
48
Page 50
Part
Name
Description
Phenomena
Failure Cause
Light leakage
B/L unit badness
Brightness
at bottom of LCM brighter
than normal
Mechanlcal or B/L
B/L brightness asymmetric
Uniformity
Sheet in B/L unit is uneven
Mount hole
Lack screw
or screw damage
*Lack screw
Screw damage
49
Model No.: 40D3505
Service Manual
Page 51
Sincere Forever
Haier Group
Haier Industrial Park, No.1, Haier Road
266101, Qingdao, China
http://www.haier.com
Printed in China
Loading...