Haan SELECT SI-60 Instruction Manual

name: Select
model number: SI-60
“Adjustable steam for all types of floors.”
Instruction Manual
HAAN® Corporation
1866 Colonial Village Lane Lancaster, PA 17601
phone: 877-422-6347
www.HAANusa.com
SI60_IS0006
Copyright ©2010 HAAN® Corporation
All rights reserved. No part of this document may be photocopied, reproduced or translated to another language without prior written consent of HAAN® Corporation.
HAAN® is a registered trademark of the HAAN® Corporation.
HAAN® Experience Steam. Discover Clean. is a trademark of the HAAN® Corporation.
Notice
The information contained in this document is subject to change without notice.
HAAN® Corporation assumes no responsibility for any errors that may appear in this document nor does it make expressed or implied warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
HAAN® Corporation shall not be liable for incidental or consequential damag­es in connection with or arising out of the furnishing, performance, or use of this document and the program materi­als which it describes.
Introduction
Congratulations on purchasing a HAAN
®
product. Now
you have an easy way to clean your tile, hardwood, lami­nate, linoleum and vinyl floors.
Your floor sanitizer uses steam to remove tough grease, dirt and grime. Steam is nature’s purest and most power­ful cleaner for safely cleaning all hard surfaces in your home without harsh chemicals, for a perfectly ecologi­cal approach. No film, no residue – just clean, germ-free
floors.
HAAN
®
products are so easy to assemble, you can put them to use right away – anywhere you want to clean and sanitize – from your kitchen and living room to your
bathroom floors.
Backed with a one-year limited warranty, your quality
HAAN
®
product is sure to give you years of dependabil­ity. And our Customer Care representatives are available to answer any of your questions about your new floor sanitizer.
Thousands of HAAN® customers have already fallen in love with HAAN® Floor Sanitizers. We’re confident you
will, too.
Thank you again for purchasing the HAAN® Select Floor Sanitizing Steam Mop.
The HAAN
®
Team
1
2
Basic precautions should be observed when using an electrical appliance, including the following:
1. Do not direct steam at people, animals, or at electrical outlets.
2. Do not expose to rain.
3. Store indoors.
4. Unplug from outlet when not in use and before conducting service maintenance or trouble-shooting.
5. Do not leave steam cleaner unattended.
6. Do not leave the steam cleaner connected to an electrical outlet when not in use.
7. Do not service steam cleaner when it is plugged in.
8. Do not use with damaged cord or plug.
9. Do not use steam cleaner if it has been dropped, damaged, left outdoors or dropped into water. Return to a service center.
10. Do not handle steam cleaner with wet hands.
11. Do not pull or carry by cord, use cord as a handle, close door on cord, pull cord around sharp corners or expose cord to heated surfaces.
12. Do not unplug by pulling on cord.
13. Do not use appliance in an enclosed space filled with vapor given off by oil-base paint thinner, some moth-proofing substances, flammable dust, or other explosive or toxic vapors.
14. Do not allow to be used as a toy.
15. Do not use on leather, wax polished furniture or floors, synthetic fabrics, velvet or other delicate, steam-sensitive materials.
16. Do not immerse in water or any other liquid.
17. Do not use for any purpose other than described in this User Manual.
18. Use only manufacturer’s recommended attachments – use of attachments not provided or sold by HAAN® may cause fire, electric shock or injury.
Important Safety Instructions
IMPORTANT
Be sure to read ALL instructions and warnings before using your HAAN® Floor Sanitizer.
SAVE THESE INSTRUCTIONS:
For household use only. Any other use of this appliance will void the manufacturer’s warranty.
CAUTION
The SI-60 emits steam at 212˚F to sanitize the area of use. This means that the steam head, Ultra-Microfiber Pads and Carpet Glide get very hot during use. Care should be taken when using this appliance. DO NOT touch them during use except in the approved manner as outlined in this manual.
Risk of electrical shock: Be sure to read and follow all instruc­tions and warnings.
WARNING
3
19. Never put descaling, aromatic, alcoholic or detergent products into the steam cleaner, as this may damage it or make it unsafe for use.
20. Unplug by grasping the plug, not the cord.
21. Close attention is necessary when used by or near children.
22. If the circuit breaker activates while using the steam function, discontinue product use immediately and contact the customer support center. (Beware of the risk of electrical shock.)
23. Do not allow the product to be disassembled and/ or modified by anyone other than an authorized service technician. (Doing so can result in fire and/ or electrical shock.)
24. Do not puncture steam hose that is exposed by the swivel steam head joint.
25. This product is NOT for space heating purposes.
Important Safety Instructions
Electrical Plug Instructions:
This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse plug. If it still does not fit, contact a qualified electri­cian. Do not attempt to defeat this safety feature.
IMPORTANT
DO NOT modify the plug. Improper con­nection can result in a risk of electrical shock.
WARNING
4
Operating Instructions
Care & Maintenance
1. Turn your floor sanitizer off and unplug from the electrical outlet.
2. Wrap power cord around cord hangers.
3. Let your floor sanitizer cool for five (5) minutes before removing the ultra-microfiber pad and before emptying the water tank.
4. Always empty the water tank when you have finished using your floor sanitizer.
5. Never leave ultra-microfiber pad on floor sanitizer when you have finsihed using it. Always remove the ultra-microfiber pad and wash in warm water with a mild detergent. Never use bleach or fabric softener when cleaning the ultra-microfiber pad. The ultra-microfiber pad can be washed in a washing machine and dried in a clothes dryer but on low heat. To decrease pad wear, we recommend the pad be hung to dry for 24 hours.
6. Wipe your floor sanitizer with a damp cloth to clean. Never immerse the sanitizer in water or any other liquid.
7. In order to keep your floor sanitizer in good condition, we recommend that you clean the water tank once a month to eliminate calcium deposits. Add eight ounces (8 oz) of water to the water tank and insert 1 packet of Fresh Rinse™ Lime and Scale Remover. Shake to loosen any deposits. Place unit on resting mat without pad, turn unit on and allow water to steam until water in tank is depleted. Do
not use vinegar or other decalcifying substances in the floor sanitizer water tank.
IMPORTANT
Always ensure that your floor sanitizer is UNPLUGGED from the wall receptacle prior to cleaning or emptying the water tank.
CAUTION
CAUTION
Do not immerse your floor sanitizer in water or any other liquid.
Always operate floor sanitizer by gripping the handle. Do not grip by the pole.
Helpful Hints
1. Always use a vacuum or sweep before sanitizing your floors.
2. The easiest way to use the machine is to tilt the handle to a 45º angle and clean slowly 2-3 yards at a time.
5
Ultra-Microfiber Pads for HAAN® Floor Sanitizing Steam Mop
Helpful Hints Cont.
3. A good amount of steam passes through the ultra-microfiber pad. We recommend that the ultra-microfiber pad be changed when it becomes oversaturated.
4. To remove stubborn stains from vinyl or linoleum floors, pre-treat with a mild detergent and some water before using the floor sanitizer.
What is an ultra-microfiber?
An ultra-microfiber is a textile fiber that is thinner and more absorbent than a micro­fiber (1.0dtex) pad typically used with steam mops. Specifically, to be defined as an ultra-microfiber, it should be less than 0.2dtex. The Ultra-Microfiber pad by HAAN® Corporation is made of .17dtex ultra-microfibers.
How to Use Ultra-Microfiber Pads
1. Please make sure that a completely dry pad is used.
2. As high temperature steam passes through a pad to contact the floor to kill germs, molds, mites and to provide a certain amount of water necessary for cleaning, it is natural that the pad gradually absorbs moisture. After a certain length of time, the pad repels water and becomes damp.
3. To keep the floor clean and dry, replace the pad when it is dirty.
4. Only remove pad from unit when not in use and steam is not being emitted.
How to Clean and Store
1. Hand wash or machine wash the ultra-microfiber pad in cold water on the delicate cycle with a mild detergent. (Do not use a fabric softener)
2. Using a washing machine may shorten the lifespan of the pads.
3. We recommend air drying the ultra-microfiber pad for 24 hours, but they could be dried in a dryer on a low heat setting.
Chlorate
bleach
Hanger Lightly
6
Handle Assembly:
Line up groove &
insert into unit.
Floor Setting Indicator Light:
Ideal for ceramic, stone, tile and other durable floors.
Perfect for sealed hardwood, laminate, bamboo and other delicate floors.
Product Assembly & Parts
1
5
6
7
8
9
10
11
12
14 15
13
16 17
2
3
4
A
B
Base Assembly:
Insert screw as shown. Tighten using
a flat-head screwdriver. If screw
turns freely without “gripping” the
insert threads, apply additional pres-
sure when turning.
7
Before Using Your Floor Sanitizer
Be sure to read ALL instructions and warnings before using your Floor Sanitizer.
1. Handle
2. Floor Setting Control
3. Floor Setting Indicator Light
4. Steam Power Switch
5. Telescopic Handle
6. Handle Length Adjustment Button
7. Storage Hook (rotates 360º)
8. Main Body Assembly Screw
9. Power Cord
10. Water Tank Release Button
11. Detachable Water Tank
12. Power Cord Organizer (bottom)
13. Assembly Screw (x1) Located in Fresh Rinse Bag
14. Floor Protector / Resting Mat
15. Carpet Glide
16. Ultra-microfiber Pads (x2)
17. Fresh Rinse Lime & Scale Remover (x12)
Helpful Hint:
To extend the life of your Ultra-Microfiber Pads, always place your unit on the floor protector/resting mat while the unit heats up. Attach the Ultra-Mi­crofiber pad when the unit is ready to use.
Helpful Hint: Helpful Hint:
When heated, never leave the ap­pliance in one spot on any surface for any period of time. Always place your Floor Sanitizer on the Floor Protector/Resting Mat when stationary.
Always empty water from water tank after use. To ensure opti­mum product function use Fresh Rinse™ once a month.
Helpful Hint:
When using the Floor Sanitizer with the Carpet Glide it will not lift all set-in stains from your carpet, our patented Ultra-micro­fiber pad may be used to act as a “blotter” for removing most fresh, wet spills and stains.
Your floor sanitizer is designed to clean hard floor surfaces that will withstand high heat. Do not use on unsealed wood or unglazed ceramic floors. On surfaces that have been treated with wax or some no-wax floors, the sheen may be removed by the heat and steam action. It is always recommended to test an isolated area of the surface to be cleaned before proceeding. We also recommend that you check the use and care instructions from the floor manufacturer.
WARNING
8
Using Your Floor Sanitizer - Operating Instructions
Before Using Your Floor Sanitizer cont.
IMPORTANT
This product is NOT for space heating purposes.
CAUTION
CAUTION
Use only a heavy duty extension cord rated for 15 amps minimum – DO NOT use an ordinary extension cord.
HAAN® floor care products emit steam at 212º to sanitize the area of use. This means that the steam head, Ultra-microfiber pads and carpet glide get very hot during use. Care should be taken when using this appliance and DO NOT touch components of this machine during use except in the approved manner as outlined in this manual.
1
4
Assemble unit and place on Floor Protector / Resting Mat.
Tighten cap. Insert tank (cap down) until it “clicks”.
2
5
Press Water Tank Release but­ton and remove water tank.
Press ON/OFF button. Wait 20 seconds for unit to heat up. Unit may vibrate while heating.
3
6
Turn Cap counterclockwise to Remove. Fill tank with water.
Gently place unit on Ultra­microfiber pad. You are now ready to steam clean.
9
IMPORTANT: Vibration Sound
IMPORTANT
Floor Setting Indicator Light
Floor Setting Button
While the unit is turned off, air builds up in the water pump
line. This is a common occurrence. When the unit is turned on
the water pump pushes air out of the line and emits a vibrating
sound. This occurs while the unit is heating up and also when
the water tank is emptied during use. If the vibration sound
persists for more than 60 seconds during heat up, check to make
sure the water tank is assembled correctly.
Always empty the water tank once you have finished using your
Floor Sanitizer.
7
10
Tilt handle at a 45º angle. Push and pull slowly across the floor to clean thoroughly.
When unit has cooled, remove Ultra-microfiber pad. Store unit upright in a dry area.
8
When done, push ON/OFF button.
9
Place unit with Ultra-microfi­ber pad attached onto Floor Protector / Resting Mat. Allow to cool down for five (5) min.
FLOOR
SETTING
High steam emission ideal for ceramic, stone, tile and other durable floors.
Gentle steam emission perfect for sealed hardwood, laminate, bamboo and other delicate floors.
Use this button to switch between two steam levels, each catering to specific floor types.
This light indicates which steam floor setting level is selected.
10
Using the Carpet Glide - FOR FRESH STAINS
1
4
Place unit on stain. Let stand for a few seconds. Allow steam to saturate stain.
2
5
Slowly move unit back and forth over stain.
“Hands Free” Removal Tab
3
6
Remove carpet glide from unit with hands free tab.
TAB
TAB
“Hands Free”
Removal Tab
1 2 3
Attach carpet glide by placing unit under “tabs” and gently pushing down into place.
With carpet glide attached, place on Floor Protector / Resting Mat. Turn unit ON and follow operat­ing instructions to clean.
Turn unit OFF, let cool. Use foot on “Hands Free” tab to remove Tray from steam head.
To Remove Carpet Glide
Using the Carpet Glide
What is the Carpet Glide?
The carpet glide enables the Floor Sanitizer to freshen, deodorize and sanitize carpet­ing, rugs, upholstery, pet cushions and more. Used with the Floor Sanitizer it kills dust mites and other allergans on a variety of surfaces.
NOTE: The Carpet Glide is used WITHOUT the Ultra-Microfiber Pad.
Gently place unit on Ultra­microfiber pad.
Use the pad to rub the area “blotting” out the stain.
Turn unit OFF. When cooled, remove Ultra-microfiber pad.
11
Vibration sound last lon­ger than 60 seconds.
White spot left on floor.
Unit does not emit steam.
Water left on floor.
Unit not operating.
• Add water to the water tank.
• Ensure that water tank is inserted correctly in unit.
• When cleaning do not leave unit in one spot for too long.
• Use protector pad / oor mat when unit is ON and stationary.
• Use distilled water instead of hard tap water.
NOTE: To remove spot, use a damp cloth with a few drops of white vinegar to rub and remove stain.
• Ensure water tank is lled with water.
• Change the Ultra-microber pad.
• Ensure unit is always level and parallel to the oor.
• Ensure plug is set rmly in outlet.
• Replace fuse or reset breaker.
Troubleshooting
Problem Solution
12
Q: Can the HAAN Floor Sanitizer be used on laminate flooring?
A: Yes. Your floor sanitizer was designed to be gentle on delicate flooring, yet power­ful enough to penetrate stains and kill harmful germs and bacteria. The HAAN Select, with 2 unique floor type settings, was designed to be safer on delicate floors than traditional steam mops.
Q: How long can an Ultra-microfiber Pad be used until it needs to be changed?
A: The pad should be changed every 10 minutes, or when it becomes saturated with water. The unit will become harder to push with a overly wet pad.
Q: How long does a tank of water last?
A: A full tank will last approximately 20-25 minutes. Varies upon which floor setting you are using.
Q: Sometimes my floor sanitizer becomes hard to push - why?
A: If the unit is hard to push its likely because the Ultra-microfiber Pad is too wet or the angle at which you are using the machine is too high.
Q: How do you use the Carpet Glide for my carpet?
A: The carpet glide is to be used without the Ultra-microfiber Pad and can be attached directly to the unit.
Q: Does the HAAN work on pet stains?
A: Yes, the HAAN is able to spot clean fresh pet stains by loosening and lifting the stain.
Q: How can I prolong the life of my HAAN?
A: To maintain the life of your unit, we recommend using the Fresh Rinse once a month.
Q: Will the HAAN Floor Sanitizer clean grout?
A: Yes, but it needs a little help. If you glide your HAAN over the problem areas and then scrub with your Ultra-microfiber Pad, it should effectively clean your grout.
Commony Asked Questions
Couldn’t find the Answer to your Question?
Call Customer Care at 877-HAAN DIRECT / 877-422-6347
13
To order additional pads, accessories or replacement
parts call customer care at:
877-HAAN DIRECT / 877-422-6347
Or visit:
www.HAANusa.com
Product Specifications: Model SI-60
Color
Size
Weight
Voltage/Hz
Wattage
Cord Length
Tank Capacity
Heat-up Time
Operating Time
*Dimensions approximated. Dimensions include base and measured without hose, or attachments.
Grey and Red
11.8” W x 6.8” D x 44” H (min) - 50.5” (max)
4.6 lb
AC 120V, 60Hz
1200 watts
25 Feet
11.83 oz.
20 sec.
Up to 25 min. dependent upon steam setting
One-Year Limited Warranty
Your HAAN® Floor Sanitizer is warranted to be free from defects in material and work­manship for a period of one (1) year from the date of purchase when utilized for normal household use by the original purchaser only. The included Warranty Registra­tion Card should be filled out and returned within thirty (30) days of purchase. This will register your product. Should any defect covered by the terms of the limited warranty be discovered within one year, HAAN® Corporation will repair or replace the defec­tive part, provided the unit is returned by the original purchaser, freight prepaid, to: HAAN® Corporation, 1866 Colonial Village Lane, Lancaster, PA 17601. Proof of purchase is required and should accompany the return.
The liability under this warranty is limited solely to the cost of the replacement parts or the complete unit at our option. Labor charges are not included.
This warranty is extended to the original purchaser of the unit and excludes all other legal and/or conventional warranties. The responsibility of HAAN® Corporation, if any, is limited to the specific obligations expressly assumed by it under the terms of the limited warranty. In no event is HAAN® Corporation liable for incidental or conse­quential damages of any nature whatsoever. Some states/provinces do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you. This warranty gives you specific legal rights which vary from state to state or province to province.
IMPORTANT: Before packing be sure to attach a tag to item with your name, complete address, phone number and a note giving purchase information, model number and what you believe to be the problem with the item. Carefully pack item to avoid damage in shipping. To expedite your repair, we request that you call Customer Care to report the problem prior to shipping your product back. We also recommend that you insure the package (as damage in shipping is not covered by our warranty). Mark the outside of your package “ATTENTION CUSTOMER CARE.” We are constantly striving to improve our products; therefore, the specifications contained herein are subject to change with­out notice.
Warranty Notice: FAILURE TO COMPLETE AND RETURN THE PRODUCT REGISTRATION CARD WILL NOT DIMINISH YOUR WARRANTY RIGHTS.
Product Registration
Please fill out and mail this Product Registration Card within thirty
(30) days of purchase in order to validate the foresaid Limited War-
ranty. The registration will allow us to contact you in the unlikely
event of a product safety notification. By returning this card you
acknowledge that you have read and understood the instructions for
use and the warnings set forth within the instructions.
Warranty Notice: FAILURE TO COMPLETE AND RETURN THIS
PRODUCT REGISTRATION CARD WILL NOT DIMINISH YOUR WAR-
RANTY RIGHTS.
Yes! I would like HAAN® to send me information on products and
services including new product releases,events and special of-
fers. You may contact me by:
What other HAAN
®
products have you purchased?
1)
EMAIL
PHONE
MAIL
2)
Privacy Notice: We use this information requested on this card to
process your registration, thereby allowing you to receive the benets
of being a registered user, and for use in post-sales services. Other
uses of your information are governed by the choices you make in
answering the questions and the HAAN privacy policy. For information
on this policy contact 877- HAAN DIRECT.
(Fold here and tape closed before mailing)
Cut along dashed line
First Name
Address
City
Zip Code/Postal Code
Product Name/Model number
Date Purchased Place of Purchase
Last Name
State/Province
Country/Territory
Product Registration
HAAN® Corporation
1866 Colonial Village Lane Lancaster, PA 17601
Place
Stamp
Here
3) Where did you purchase your HAAN
®
product?
4) How did you hear about HAAN
®
?
5) We like to hear from our product owners. Please add any
comments here:
Loading...