name: Multiforce Pro™
model number: SS-25
“First of its kind steam
cleaner with high velocity
CR-motion™ technology.”
Instruction Manual
HAAN® Corporation
1828 William Penn Way
Lancaster, PA 17601
phone: 877-422-6347
www.HAANusa.com
SS25_IS0018
Product Registration
HAAN® Corporation
1828 William Penn Way
Lancaster, PA 17601
Place
Stamp
Here
3) Where did you purchase your HAAN
®
product?
4) How did you hear about HAAN
®
?
5) We like to hear from our product owners. Please add any
comments here:
Copyright ©2012 HAAN® Corporation
All rights reserved. No part of this
document may be photocopied,
reproduced or translated to another language
without prior written
consent of HAAN® Corporation.
HAAN® is a registered trademark of
the HAAN® Corporation.
HAAN® Experience Steam. Discover Clean.™
is a trademark of the HAAN® Corporation.
Notice
The information contained in this
document is subject to change
without notice.
HAAN® Corporation assumes no
responsibility for any errors that may
appear in this document nor does it
make expressed or implied warranty
of any kind with regard to this material,
including, but not limited to, the implied
warranties of merchantability and
fitness for a particular purpose.
HAAN® Corporation shall not be liable
for incidental or consequential damages in connection with or arising out of
the furnishing, performance, or use of
this document and the program materials which it describes.
Product Registration
Please fill ou t and mail th is Prod uct Reg istration Card within thirt y
(30) d ays of purchas e in ord er to validat e the fore sai d Limited
Warranty. The regist ration will allow u s to contact you in the unlikely
event of a p roduct safety n otification. B y retur ning t his card you
acknow ledge t hat yo u have read an d under stood the ins tructio ns for
use and the warnings set forth within the instructions.
Warranty Notice: FAILURE TO COMPLETE AND RETURN THIS
PRODUCT REGISTRATION CARD WILL NOT DIMINISH YOUR WAR-
RANTY RIGHTS.
Yes! I would like HAAN® to send me i nformation on products and
services including new product releases, events and special of-
fers. You may contact me by:
What other HAAN
®
products have you purchased?
1)
EMAIL
PHONE
MAIL
2)
Privacy Notice: We use this info rmation requested on this ca rd to
process your registration, th ereby allowing you to receive the benets
of being a reg istered user, and for us e in post-sal es services. Other
uses of your information are governed by the choices you make in
answering th e questions a nd the HAAN privacy policy. For in formation
on this poli cy contact 87 7- HAAN DIRECT.
(Fold here and tape closed before mailing)
Cut along dashed line
First Name
Address
City
Zip Code/Postal Code
Product Name/Model number
Date Purchased Place of Purchase
Last Name
State/Province
Country/Territory
Introduction
Congratulations on purchasing a HAAN
®
product. Now
you have an easy way to clean your tile, hardwood, laminate, linoleum and vinyl floors.
The Multiforce Pro™ uses steam to remove tough grease,
dirt and grime. Steam is nature’s purest and most powerful cleaner for all hard surfaces in your home.
The Multiforce Pro™ also uses CR-motion™ technology.
This technology uses the power of reciprocating motion to
further enhance the cleaning power of steam.
HAAN
®
products are so easy to assemble, you can put
them to use right away – anywhere you want to clean
and sanitize – from your kitchen and living room to your
bathroom floors and outdoor surfaces.
Backed with a one-year limited warranty, your quality
HAAN
®
product is sure to give you years of dependability. And our Customer Care representatives are available
to answer any of your questions about your new floor
sanitizer.
Thousands of HAAN® customers have already fallen in
love with HAAN® Floor Sanitizers. We’re confident you
will, too.
Thank you again for purchasing a HAAN®.
The HAAN
®
Team
1
Product Specifications: Model SS-25
Color
Size
Weight
Voltage/Hz
Wattage
Cord Length
Tank Capacity
Heat-up Time
Operating Time
*Dimensions approximated. Dimensions include base and measured without hose, or attachments.
Grey and Red
10.27” W x 9.8” D x 45.67” H
7.27 lb
AC 120V, 60Hz
1200 watts
18 Feet
11.83 fl. oz.
40-45 sec.
17 min. (High Setting) 23 min. (Gentle Setting)
One-Year Limited Warranty
Your HAAN® Steamer is warranted to be free from defects in material and workmanship for a period of one (1) year from the date of purchase when utilized for normal
household use by the original purchaser only. The included Warranty Registration
Card should be filled out and returned within thirty (30) days of purchase. This will
register your product.
Should any defect covered by the terms of the limited warranty be discovered within
one year, HAAN® Corporation will repair or replace the defective part. To process a
warranty cl aim, contact c ustomer care at 1-877-42 2-6347 for fur ther assistanc e and
instructions. A customer care agent will conduct trouble shooting in an attempt to fix
any minor problems. Should trouble shooting not provide any result, a return authorizatio n will be issu ed. Proof of purchas e is requi red and should accompany the return .
Freight costs must be prepaid by the purchaser.
The liability under this warranty is limited solely to the cost of the replacement parts
or the complete unit at our option. Labor charges are not included.
This warran ty is exte nded to the or iginal purchaser of the unit and excludes all oth er
legal and/or conventional warranties. The responsibility of HAAN® Corporation, if
any, is limited to the specific obligations expressly assumed by it under the terms of
the limited warranty. In no event is HAAN® Corporation liable for incidental or consequent ial damages of any nature whatsoever. Some states/provinces do n ot permit the
exclusion or limitation of incidental or consequential damages, so the above may not
apply to you. T his warranty gives you specific legal rights which vary from stat e to
state or province to province.
Warranty Notice: failure to complete and return the product registration card will
not diminish your warranty rights.
Notes
2 19
1. Use the system only for its intended use.
2. Do not leave the Multiforce Pro™ unattended
when plugged in. Turn it off and unplug the
electrical cord from the outlet when not in use.
3. Do not allow to be used as a toy. Pay close
attention when used near children, pets or
plants. Do not leave the Multiforce Pro™ unattended
while plugged in.
4. Use only as described in this manual.
5. Use only manufacturer’s recommended
accessories.
6. Do not operate the Multiforce Pro™ with a
damaged plug or cord. Do not use it if the
Multiforce Pro™ has been dropped or damaged. To
avoid the risk of electric shock do not
disassemble or attempt to repair it on your
own. Incorrect re-assembly or repair can cause
a risk of electric shock or injury to persons
when the Multiforce Pro™ is used.
7. To protect against a risk of electric shock, do
not immerse the Multiforce Pro™ into water or any
other liquid.
8. Do not pull or carry by power cord, use cord
as handle, close a door on cord, or pull cord
around sharp edges or corners. Keep cord
away from heated surfaces.
9. Do not unplug by pulling on power cord. To
unplug, grasp the plug not the cord. Do not
use extension cords or outlets with inadequate
current capacity.
10. Turn the unit off before unplugging from
electrical outlet.
11. Do not handle plug or the Multiforce Pro™ with
wet hands or operate it without shoes.
12. Do not put foreign objects into openings. Do
not use with any opening blocked.
13. Do not put hands or feet under the
Multiforce Pro™. It gets very hot.
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING
(THIS APPLIANCE)
SAVE THESE
INSTRUCTIONS:
For household use only.
Any other use of this
appliance will void the
manufacturer’s warranty.
The Multiforce Pro™
emits steam at 212˚F
to sanitize the area
of use. This means
that the steam head,
Ultra-Microfiber Pads,
Scrub Brushes and
Carpet Glide get very
hot during use. Care
should be taken when
using this appliance.
DO NOT touch them
during use except in
the approved manner as outlined in this
manual.
Risk of electrical
shock: Be sure to read
and follow all instructions and warnings.
When using the Multiforce Pro™ basic safety precautions should always be observed, including the
following:
To reduce the risk of fire, electric shock, or injury:
WARNING
WARNING
WARNING
CAUTION
Do not use to pick up
flammable or combustible liquids, such as
gasoline, or use in areas where combustible
liquids may be present.
14. Use ONLY on flat, horizontal surfaces. Do not use
on walls, counters or windows.
15. Do not add cleaning solutions, scented perfumes,
oils or any other chemicals to the water used in
the Multiforce Pro™ as this may damage it or make
it unsafe for use. Use regular tap water or distilled
purified water if the tap water in your area is very
hard.
16. When in use, never turn the Multiforce Pro™ over or
on its side. Never direct steam towards people,
animals or plants.
17. Do not handle the ultra-microfiber pads immediately
after turning the Multiforce Pro™ off. Place the Multiforce Pro™
on the floor protector pad to cool down before removing.
18. Never leave the Multiforce Pro™ steaming in one spot on
any surface for any period of time. Always place
on the floor protector pad and make sure that the
Multiforce Pro™ is turned off.
19. When cleaning the Multiforce Pro™, turn if off and
clean with a dry or damp cloth. Do not pour water
or use alcohol, benzene or turpentine on the unit.
20. Extreme caution should be exercised when using
the Multiforce Pro™ to clean stairs.
21. Never use the Multiforce Pro™ without the ultra-microfiber
cleaning pads, polish pads, scrub brushes or
carpet glide attached.
22. Keep your work area well lit.
23. Store the Multiforce Pro™ in doors in a cool, dry place.
24. Do not open the water tank cap to refill or empty
the water tank when power is turned on.
25. Do not bend the power cord excessively or place
heavy objects on the power cord.
26. If the power cord has become knotted and or worn
contact the service center for replacement
power cord.
27. Do not operate the Multiforce Pro™ if the power indicator
lamp flickers. Contact the Customer Care at 877-422-6347.
28. Always properly insert the power cord in to the cord
hanger when in use.
29. To protect the power cord, coil the power cord over
two cord racks (upper and lower) loosely for storage
when not in use.
30. Keep hair, loose clothing, fingers, and all parts of
body away from openings and moving parts.
31. Connect to a properly grounded outlet only. See
grounding instructions.
32. Do not use CR-motion™ with Carpet Glide.
33. WARNING - To reduce the risk of fire, use only
commercially available floor cleaners and waxes
intended for machine application.
34. Connect to a properly grounded outlet only.
See Grounding Instructions.
WARNING
318
Important Safety Instructions
DO NOT use CRmotion™ when Carpet
Glide is attached to
product. Doing so
could result in product
malfunction or product
failure.
WARNING
Notes
174
1. Ne pas laisser l’apparecil sans surveillance lorsqu’il est branché. Le débrancher
lorsqu’il n’est pas utilisé et avant le dépannage.
2. Ne pas laisser les enfants jouer avec l’appareil ou s’en servir sans surveillance. Redoubler d’attention s’il y a des enfants á proximite lorsqu’on utilise l’appareil.
3. Utiliser l’appareil en respectant les consignes de celte notice d’emploi et n’utiliser
que les accessoires recommandés par le fabricant.
4. Ne pas utiliser l’appareil si le cordon ou la fiche est endommagé. Retoumer
l’appareil á un atelier de réparation s’il ne fonctionne pas normalement, s’il a été
échappé, s’il est endommagé, s’il a été oublié á l’extérieur ou immergé.
5. Le cordon ne doit pas étre utilisé comme une poignée ou pour tirer, trainer ou soulever l’appareil. Ne pas faire passer l’appareil sur le cordon ; ne pas coincer le cordon
dans l’embrasure en refermant les portes ni tierer dessus á l’angle d’un mur ou d’une
autre aréte vive et le tenir á distance des surfaces chaudes.
6. Ne pas tirer sur le cordon pour débrancher l’appareil; tirer plutót sur la fiche.
7. Ne pas toucher la fiche du cordon ou l’appareil avec les mains humides.
8. Ne pas insérer d’objet dans une ouverture quelconque de l’appareil. Ne pas utiliser
l’appareil lorsqu’une ouverture est blogquée et enlever la poussiére. la peluche, les
cheveux, etc., qui peuvent gener le débit d’air.
9. Veiller á bien se garder - doigts, cheveux, vétements amples - á distance des ouvertures des pieces mobiles.
10. Mettre toutes les commandes en position d’arrét avant de débrancher l’appareil.
11. Redoubler d’attention en nettoyant les escaliers.
12. Ne pas se servir de l’appareil pour aspirer des laquides combustibles ou inflammables comme de l’essence ou dans un endroit oú il peut y avoir de tels liquides.
13. Doit être branché sur une prise de courant avec mise à la terre. Voir les instructions
de mise à la terre.
14. Pour réduire le risque du feu, employez seulement les décapants disponibles dans
le commerce et les cires de plancher destinés pour l’application de machine.
IMPORTANTES MESURES DE SÉCURITE
CONSERVER CES INSTRUCTIONS
LIRE TOUTES LES INSTRUCTIONS AVANT
D’UTILISER (CET APPAREIL)
L’utilisation d’un appareil électrique demande certaines précautions, dont
les suivantes:
pour réduire le risque d’incendie, de choc électrique ou de blessure:
AVERTISSEMENT:
To order additional pads, accessories or replacement
parts call customer care at:
877-HAAN DIRECT / 877-422-6347
Or visit:
www.HAANusa.com
516
Operating Instructions
Do not immerse the
Multiforce Pro™ in
water or any other
liquid.
1. The easiest way to use the machine is to tilt the handle to a 45º angle and
clean slowly 2-3 yards at a time.
2. Hand wash or machine wash the ultra-microfiber pads in the delicate cycle
with a mild detergent.
3. We recommend air drying the ultra-microfiber pads for 24 hours, but they
could be dried in a dryer on a low heat setting.
4. A good amount of steam passes through the ultra-microfiber pads. We
recommend that the ultra-microfiber pads be changed when it
becomes oversaturated.
5. To remove stubborn stains from vinyl or linoleum floors, pre-treat with a mild
detergent and some water before using the floor sanitizer.
Always operate the
Multiforce Pro™ by
gripping the handle.
Do not grip by the
pole.
Care & Maintenance
1. Turn the Multiforce Pro™ off and unplug from
the electrical outlet.
2. Wrap power cord around cord hangers.
3. Let the Multiforce Pro™ cool for five (5) minutes
before removing the ultra-microfiber pads and
before emptying the water tank.
4. Always empty the water tank when you have
finished using the Multiforce Pro™.
5. Never leave ultra-microfiber pads on the
Multiforce Pro™ when you have finished using it.
Always remove the ultra-microfiber pads and
wash in warm water with a mild detergent.
Never use bleach or fabric softener when
cleaning the ultra-microfiber pads.
The ultra-microfiber pads can be washed in a
washing machine and dried in a clothes
dryer but on low heat.
To decrease pad wear, we recommend the
pads be hung to dry for 24 hours.
6. Wipe the Multiforce Pro™ with a damp cloth to
clean. Never immerse the Multiforce Pro™ in water
or any other liquid.
7. In order to keep the Multiforce Pro™ in good
condition, we recommend that you clean the
water tank once a month to eliminate calcium
deposits. Add eight ounces (8 oz) of water to
the water tank and insert 1 packet of Fresh
Rinse™ Lime and Scale Remover. Shake to
loosen any deposits. Place unit on resting
mat without pads, turn unit on and allow water
to steam until water in tank is depleted. Do
not use vinegar or other decalcifying
substances in the floor sanitizer
water tank.
IMPORTANT
Always ensure that the
Multiforce Pro™ is
UNPLUGGED from the
wall receptacle prior to
cleaning or emptying
the water tank.
CAUTION
CAUTION
IMPORTANT: Never leave the Multiforce Pro™ steaming in one spot on any surface for any period of
time.Always place on the floor protector pad and make sure that the floor sanitizer is turned off.
SAVE THESE
INSTRUCTIONS | FOR
HOUSEHOLD USE
Commerci al use of this
unit voids the manufacturer’s warranty.
Helpful Hints
Q: Can the Multiforce Pro™ be used on laminate flooring?
A: Yes. Your steam mop was designed to be gentle on delicate flooring, yet powerful
enough to penetrate stains and kill harmful germs and bacteria.
It is recommended that the flooring manufacturer be contacted to see if it is OK to
clean the floor with steam. Leaving the steam mop sitting in one spot while steaming
could result in discoloration of flooring.
Q: How long can an Ultra-microfiber Pad be used until it needs to be changed?
A: The pad should be changed every 10 minutes, or when it becomes saturated with
water. The unit will become harder to push with a overly wet pad.
Q: How long does a tank of water last?
A: A full tank will last approximately 20-25 minutes.
Q: Sometimes my floor sanitizer becomes hard to push - why?
A: If the unit is hard to push its likely because the Ultra-microfiber Pad is too wet or
the angle at which you are using the machine is too high.
Q: How do you use the Carpet Glide for my carpet?
A: The carpet glide is to be used without the Ultra-microfiber Pad and can be attached
directly to the unit. DO NOT use CR-motion™ with the Carpet Glide.
Q: Does the HAAN work on pet stains?
A: Yes, the HAAN is able to spot clean fresh pet stains by loosening and lifting the
stain.
Q: How can I prolong the life of my HAAN?
A: To maintain the life of your unit, we recommend using the Fresh Rinse once a
month.
Q: Will the HAAN Floor Sanitizer clean grout?
A: Yes, but it needs a little help. If you glide your HAAN over the problem areas and
then scrub with your Ultra-microfiber Pad, it should effectively clean your grout.
Commonly Asked Questions
Couldn’t find the Answer to your Question?
Call Customer Care at 877-HAAN DIRECT / 877-422-6347
156
1. To avoid circuit overload, do not operate another appliance on the same
electrical outlet (circuit).
2. If an extension cord is absolutely necessary, a 15 amp 16 gauge cord should
be used. Cords rated for less average may overheat. Care should be taken
to arrange cord so that it cannot be pulled or tripped over.
3. Do not leave unattended when the system is connected to a power supply
electrical outlet.
A) For all grounded, cord-connected appliances:
This appliance must be grounded. If it should malfunction or breakdown, grounding provides a
path of least resistance for electric current to reduce the risk of electric shock. This appliance is
equipped with a cord having an equipment-grounding conductor and grounding plug. The plug
must be inserted into an appropriate outlet that is properly installed and grounded in accordance
with all local codes and ordinances.
WARNING - Improper connection of the equipment-grounding conductor can result in a risk
of electric shock. Check with a qualified electrician or service person if you are in doubt as to
whether the outlet is properly grounded. Do not modify the plug provided with the appliance - if it
will not fit the outlet, have a proper outlet installed by a qualified electrician.
1) This appliance is for use on a nominal 120-V circuit, and has a grounded plug that looks like
the plug illustrated in sketch “A”. A temporary adaptor should be used only until a properly
grounded outlet (sketch “A”) can be installed by a qualified electrician. The green colored rigid
ear, lug, or the like extending from the adaptor must be connected to a permanent ground such
as a properly grounded outlet box cover. Whenever the adaptor is used, it must be held in place
by a metal screw.
2) This appliance is for use on a nominal 120-V circuit and has a grounding attachment plug that
looks like the plug illustrated in sketch “A”. Make sure that the appliance is connected to an outlet having the same configuration as the plug. No adaptor should be used with this appliance.
ADDITIONAL IMPORTANT SAFEGUARDS
GROUNDING INSTRUCTIONS:
White spot left on floor.
Unit does not emit steam.
Water left on floor.
Unit not operating.
• When cleaning do not leave unit in one spot for too long.
• Use protector pad / oor mat when unit is ON and stationary.
• Use distilled water instead of hard tap water.
NOTE: To remove spot, use a damp cloth with a few drops of white vinegar
to rub and remove stain.
• Ensure water tank is lled with water.
• Change the Ultra-microber pad.
• Ensure unit is always level and parallel to the oor.
• Ensure plug is set rmly in outlet.
• Replace fuse or reset breaker.
Problem Solution
Troubleshooting
714
A) Tous les appareils mis á la terre et munis d’u cordon:
Cet appareil doit étre mis à la terre. En cas de défaillance ou de panne, le circuit de mise à la
terre offre au courant un chemin de moindre résistance qui réduit le risque de choc électrique.
L’appareil est pourvu d’un cordon muni d’un conducteur qui en assure la mise à la terre et d’une
fiche avec broche de terre. Cette fiche doit étre branchée sur une prise convenable, correctement installée et reliée à la terre conformément aux codes et aux réglements du lieu.
AVERTISSEMENT - Un conducteur de terre mal raccordé présente des risques de choc électrique. Consulter un électrician ou un technicien d’entretien compétent en cas de doute à propos
de la mise à la terre d’une prise quelconque. Ne pas modifier la fiche vendue avec l’appareil; si
ele ne s’insére pas daris la prise, faire installer une nouvelle prise par un électricien compétent.
1) Cet appareil destiné à un circuit nominal de 120 V est muni d’une fiche de terre semblable à
celle illustrée dans le croquis A. Un adaptateur temporaire ne devrait étre utilisé qu’en attendant
l’installation, par un électricien compétent, d’une prise correctement mise à la terre (croquis A).
L’oreillette rigide, le crochet ou autre dispositil de couleur verte intégré à l’adaptateur doit étre
connecté à un element correctement relié à la terre, par exemple le couvercle d’une bolte de
sortie mise à la terre, et il doit étre fixé à la prise au moyen d’une vis métallique.
2) Cet appareil destiné à un circuit nominal de 120 V est muni d’une fiche de terre semblabie à
ceile illustrée dans le croquis A. L’appareil doit étre branché sur une prise ayant la méme confguration que la fiche. Aucun adaptateur ne davrait étre utilisé avec cet appareil.
INSTRUCTIONS DE MISE A LA TERRE
Using the Carpet Glide
1
4
Place unit on stain. Let stand for
a few seconds. Allow steam to
saturate stain.
Gently place unit on Ultra-microfiber cleaning pads.
2
5
Slowly move unit back and forth
over stain.
Use the pad to rub the area
“blotting” out the stain.
“Hands Free”
Removal Tab
3
6
Remove carpet glide from
unit with hands free tab.
Turn unit OFF. When cooled,
remove Ultra-microfiber pads.
Using the Carpet Glide - FOR FRESH STAINS
TAB
TAB
“Hands Free”
Removal Tab
1 2
Attach carpet glide by placing
unit under “tabs” and gently
pushing down into place.
With carpet glide attached, place
on Floor Protector / Resting Mat.
Turn Steam ON and follow
operating instructions to clean.
Turn unit OFF, let cool. Use
foot on “Hands Free” tab to
remove Tray from steam head.
What is the Carpet Glide?
The carpet glide enables the Multiforce Pro™ to
freshen, deodorize and sanitize carpeting, rugs,
upholstery, pet cushions and more. Used with
the Multiforce Pro™ it kills dust mites and other
allergens on a variety of surfaces.
NOTE: The Carpet Glide is used WITHOUT the Pads
or Scrub Brushes.
3
To Remove
Carpet Glide
DO NOT use CR-motion™ when Carpet Glide
is attached to unit. Doing so could result in
product malfunction or product failure.
WARNING
8
13
What is an ultra-microfiber?
An ultra-microfiber is a textile fiber that is thinner and more absorbent than a microfiber (1.0dtex) pad typically used with steam mops. Specifically, to be defined as an
ultra-microfiber, it should be less than 0.2dtex. The Ultra-Microfiber pad by HAAN®
Corporation is made of .17dtex ultra-microfibers.
The Multiforce Pro™’s ability to clean so effectively lies in the design of its steam distribution system, CR-motion™. Two reciprocating pads moving in opposite directions
of one another provides a back-and-fourth motion that utilizes the power of steam to
clean. Each pad has 10 steam jets that provide a continuous flow of 212º steam. The
steam jets are strategically positioned on the pads to produce a consistent flow of
high temperature steam from one end of the pad to the other. The Multiforce Pro™’s
CR-motion™ technology enhances the natural pull-and-push motion of standard
steam mops and takes steam cleaning to a whole new level.
The Multiforce Pro™ offers a number of cleaning options:
1. Steam can be used without CR-motion™.
2. CR-motion™ can be used without steam.
3. Steam and CR-motion™ can be used simultaneously.
Steam, Scrub, Buff and Polish - All in One Machine.
To Steam, or Not to Steam - It’s your choice.
How to Use Ultra-Microfiber Pads
1. Please make sure that a completely dry pad is used.
2. As high temperature steam passes through a pad to contact the floor
to kill germs, molds, mites and to provide a certain amount of water
necessary for cleaning, it is natural that the pad gradually absorbs
moisture. After a certain length of time, the pad repels water and
becomes damp.
3. To keep the floor clean and dry, replace the pad when it is dirty.
4. Only remove pad from unit when not in use and steam is not being
emitted.
How to Clean and Store
1. Hand wash or machine wash the ultra-microfiber pad in cold water
on the delicate cycle with a mild detergent. (Do not use a
fabric softener)
2. Using a washing machine may shorten the lifespan of the pads.
3. We recommend air drying the ultra-microfiber pad for 24 hours, but
they could be dried in a dryer on a low heat setting.
Chlorate
bleach
Hanger Lightly
Ultra-Microfiber Pads for HAAN® Multiforce Pro™
About HAAN’s CR-motion™ Technology
11
When unit has cooled, remove
pads or scrub brushes. Store
unit upright in a dry area.
10
Place unit with pads/scrub
brushes attached onto Floor
Protector / Resting Mat. Allow
to cool down for five (5) min.
Cleaning Pads and Scrub Brush Attachments
IMPORTANT IMPORTANT
Buffing Pads
Ultra-Microfiber Cleaning Pads
Scrub Brush Attachments
During use it’s normal to
hear a “clicking” sound
coming from the unit. This
sound is produced by
the water being pumped
through the unit.
Always empty the water tank
once you have finished using
the Multiforce Pro™.
When removing the pads or scrub brushes from the unit DO
NOT turn unit upright or on its side. ALWAYS lift unit UP off
the pads or scrub brushes.
Ideal when using CR-motion™ without steam. Can be used
with a floor agent to polish and shine. See page 8 for care
instructions.
NOTE: It may be helpful to apply the floor agent with the Ultra-Microfiber Cleaning Pads and finish with the Buffing Pads
Ideal when using the steam function by itself or with CRmotion™ activated. Great for cleaning laminate, hardwood,
tile and vinyl surfaces. Can also be used to “blot” fresh
stains on carpet. See page 8 for care instructions.
Ideal when using CR-motion™ with or without steam. Great
for outdoor use on decks, patios and walkways. Best when
used with a cleaning agent. To clean Scrub Brush
Attachments rinse with water.
PUSH
Floor Setting Indicator Light
Floor Setting Button
FLOOR
SETTING
Use this button to switch between two
steam levels, each catering to specific floor
types.
This light indicates which steam floor setting
level is selected.
Gentle steam emission perfect for sealed
hardwood, laminate,
bamboo and other
delicate floors.
High steam emission
ideal for ceramic,
stone, tile and other
durable floors.
IMPORTANT:
Vibration Sound
Do not use on unsealed wood or unglazed ceramic floors. On surfaces that have been treated with
wax or some no-wax floors, the sheen may be removed by heat and steam. It is always recommended
to test an isolated area of the surface to be cleaned before proceeding. We also recommend that you
check the use and care instructions from the floor manufacturer.
12
9
Product Assembly & Parts
PUSH
PUSH
1
2
3
4
12
13
14
15
16
11
17
1. Handle • 2. Floor Setting Control • 3. Floor Setting Indicator Light • 4. Steam Power Switch
5. Storage Hook (rotates 360º) • 6. Handle Assembly Screw • 7. Power Cord • 8. Water Tank
Release Button • 9. Detachable Water Tank • 10. Power Cord Organizer (bottom)
11. CR-motion™ On/Off Button • 12. Floor Protector / Resting Mat 13. Carpet Glide
14. Bufng Pads (1 set) • 15. Ultra-Microfiber Cleaning Pads (2 sets)
16. Scrub Brush Attachments (1 set) • 17. Fresh Rinse Lime & Scale Remover (x12)
18. Assembly Screw (x1) Located in Fresh Rinse Bag
B
Base Assembly:
Insert screw as shown.
Tighten using a flathead screwdriver. If
screw turns freely
without “gripping” the
insert threads, apply
additional pressure
when turning.
Ideal for ceramic, stone,
tile and other durable
floors.
Perfect for sealed hardwood, laminate, bamboo
and other delicate
floors.
5
6
7
8
9
10
18
1
4
7
Assemble unit and place on
Floor Protector / Resting Mat.
Tighten cap. Insert tank (cap
down) until it “clicks”.
Tilt handle at a 45º angle.
Push and pull slowly across
the floor to clean thoroughly.
2
5
8
Press Water Tank Release button and remove water tank.
TO STEAM: Press ON/OFF
button. Wait 40-45 seconds for
unit to heat up. Unit may vibrate
while heating.
PA D
OFF
TO ACTIVATE CR-motion:
Using foot press ON/OFF button.
3
6
9
Turn Cap counterclockwise to
remove. Fill tank with water.
Line up pads or scrub
brushes. Gently place unit on
pads or scrub brushes. You
are now ready to steam, buff
or scrub.
When done, push CR-motion
ON/OFF Button and Steam
ON/OFF Button.
Operating Instructions Continued on Next Page
PA D
OFF
Using the Multiforce Pro™ - Operating Instructions
The Multiforce Pro™ offers a number of cleaning options:
1. Steam can be used without CR-motion™.
2. CR-motion™ can be used without steam.
3. Steam and CR-motion™ can be used simultaneously.
10
11
IMPORTANT
This product is NOT for space heating purposes.
CAUTION
CAUTION
Use only a heavy duty extension cord rated for 15 amps minimum – DO NOT use an
ordinary extension cord.
HAAN® floor care products emit steam at 212º to sanitize the area of use. This
means that the steam head, Ultra-microfiber pads, scrubbing brushes and carpet
glide get very hot during use. Care should be taken when using this appliance and
DO NOT touch components of this machine during use except in the approved manner as outlined in this manual.
Before Using the Multiforce Pro™
Be sure to read ALL instructions and warnings before using
the Multiforce Pro™.
Helpful Hint:
To extend the life of your Ultra-Microfiber
Pads, always place your unit on the floor
protector/resting mat while the unit heats
up. Attach the Ultra-Microfiber pads when
the unit is ready to use.
Helpful Hint:
When heated, never leave the appliance in
one spot on any surface for any period of
time. Always place the Multiforce Pro™
on the Floor Protector/Resting Mat when
stationary.
Helpful Hint:
Always empty water from water tank
after use. To ensure optimum product function use Fresh Rinse™ once a
month.
Helpful Hint:
When using the Multiforce Pro™ with
the Carpet Glide it will not lift all set-in
stains from your carpet. Our patented
Ultra-microfiber pads may be used to
act as a “blotter” for removing most
fresh, wet spills and stains.
The Multiforce Pro™ is designed to clean hard floor surfaces that will withstand
high heat. Do not use on unsealed wood or unglazed ceramic floors. On surfaces
that have been treated with wax or some no-wax floors, the sheen may be removed
by the heat and steam. It is always recommended to test an isolated area of the surface to be cleaned before proceeding. We also recommend that you check the use
and care instructions from the floor manufacturer.
WARNING
CORRECT PAD PLACEMENT
Before Using the Multiforce Pro™ (continued)
Loading...