GW Instek LCR-8110G, LCR-8105G, LCR-8101G Data Sheet

10MHz / 5MHz / 1MHz PRECISION LCR METER

The Smarter Way to Characterize Components

The LCR-8000G Series LCR meter, with test frequency up to 10MHz, provides accuracy, versatility and high
resolution for a wide range of component measurements, even including DC resistance measurement and
Voltage/Current monitoring. The Multi-Step function allows on-screen programming of customized
measurement sequence with Pass/Fail indication. Each program includes 30 test steps and each test step can be
set with selected parameters and test limits. Under Multi-Step operation, a tedious work routine can be done
step by step automatically just at a press of a button. With Graph Mode, LCR-8110G, LCR-8105G and LCR-8101G
display the component impedance response either over a wide range of test frequency sweep or over a wide
range of test voltage sweep in a graph chart. This gives an analysis result of either impedance vs. frequency or
impedance vs. applied voltage all at a glance. GPIB and RS-232C interfaces are available as standard for
instrument control and test result display on the PC. The rich features of LCR-8000G Series easily make your
measurement tasks done at a very competitive price.

LCR-8000G Series

FEATURES

Wide Test Frequency 20Hz~10/5/1MHz

0.1% Basic Accuracy & 6 Digits
Measurement Resolution

Large LCD Display with Intuitive User
Interface

Full Measuring Functions with DUT V/I
Monitor

PASS/FAIL Function ( abs , % , )
with Judgment Alarm

Average 1 ~ 256 Times

DC Resistance Measurement

Multi Step Mode

Graph Mode

Standard RS-232C / GPIB Interface

Wide Frequency Range With Friendly
Intuitive User Interface

The LCR-8000G Series is designed to perform precision
impedance measurements over a wide frequency range
of 20Hz ~ 10MHz for LCR-8110G, 20Hz ~ 5MHz for
LCR-8105G and 20Hz ~1MHz for LCR-8101G. The
instrument is capable of measuring 11 different
parameters with 0.1% basic accuracy, which meets the
precision measurement requirements of components
and modules used in the RF circuits. The large LCD
display with single-layer operation menu of LCR-8000G
Series provides users with ultimate convenience to
plug and play without much learning time.

Multi Step Mode

The Multi-Step mode is capable of running a series of
measurements of a component at a number of user­defined steps in sequence automatically. Total 64
programs can be saved into the non-volatile memory,
and each program contains up to 30 test steps. The
parameter and Hi/Lo limits can be set respectively for
each test step. After a program being properly edited,
the instrument can run through all the measurement
steps either at a press of the button under the Manual
Trigger selection, or automatically run the program by
detecting the connection of a DUT under the Auto
Trigger selection. When all the test steps are
completed, the screen shows the measurement
reading of the parameter being selected for each step
with Pass, HI, or LO measurement result.

Graph Mode

The graph function shows the component
characteristics in visual manner. Either voltage sweep
or frequency sweep can be selected for horizontal
scale. Just select the parameter, and set the start/stop

C.

voltage or the start/stop frequency of the sweep, LCR

-8000G will run through the sequence of
measurements and show the results on a graph.
This graphical parameter measurement performs the
characteristic verification of components and
materials over the response to the changes in AC test
frequency or AC test voltage without the need of
complex programming of an external controller. When
the graph gets out of the vertical range, the LCR­8000G Series can automatically adjust the scale to
get full test information. On the graph the marker
operation is available for detailed observation.

Pass/fail Function With Judgment Alarm

In the Pass/Fail test, primary parameter measurement
result is compared with user-defined limits and the
pass or fail result is then displayed. Three methods,
including absolute limit, percentage and delta limit,
are available for Hi(high) and Lo(low) limit setting
based on the nominal test value. The Pass/Fail test
checks whether the parameter measurement result
sits within the limits, then display "PASS" for within
the limits, or "LO" for lower than the low limit, or
"HI" For higher than the high limit. A scale and bar
for displaying measurement result is shown at the
center of the screen to give a graphical identification,
which greatly reduces operator's load in a long time
inspection work. This scale and bar also facilitate the
adjustment of the variable components. Either Pass
or Fail result can be set with a buzzer alarm, which
makes component or material sorting easy with
sound identification.

APPLICATIONS

Education Lab and Training Institution

Research & Design

Quality Assurance Verification

LCR-8000G Series

C.

Made to Measure

Since 1975

SPECIFICATIONS

(*)：Basic accuracy varies with the speed, frequency, AC signal level and the impedance of DUT.

(*)

TEST FREQUENCY

INPUT IMPEDANCE

BASIC ACCURACY

TEST SPEED

TEST SIGNAL LEVELS

SHORT CIRCUIT CURRENT

MEASUREMENT RANGES

MEASUREMENT PARAMETERS

SERIES OR PARALLEL EQUIVALENT CIRCUIT

SERIES EQUIVALENT CIRCUIT ONLY

PARALLEL EQUIVALENT CIRCUIT ONLY

POLAR FORM

AVERAGE

LCD DISPLAY

INTERFACE

POWER SOURCE

DIMENSIONS & WEIGHT

ORDERING INFORMATION

LCR-8110G
LCR-8105G
LCR-8101G

10 MHz Precision LCR Meter
5 MHz Precision LCR Meter
1 MHz Precision LCR Meter

20Hz ~ 10MHz/5MHz/1MHz, 5 Digits, 0.005%

100

0.1% (R, Z, X, G, Y, B, L, C)

AC (>2kHz)
MAX: 75mS
FAST: 150mS
MEDIUM: 450mS
SLOW: 600mS

Test Signal Level (rms)Test Frequency Step Accuracy

10mV ~ 2V3MHz 1mV/10mV 2% 5mV
10mV ~ 1V> 3MHz 1mV/10mV 2% 5mV

DC
MAX: 30mS
FAST: 60mS
MEDIUM: 120mS
SLOW: 900mS

Max. 20mA

Mode

R, Z, X, Rdc
G, Y, B

L
C
D

Q

Measure Range

0.1m ~ 100M
10nS ~ 1000S

0.1nH ~ 100kH

0.01pF ~ 1F

0.00001 ~ 9.9999

0.1 ~ 9999.9

-180 ~ +180

Impedance (Z), Phase Angle ( ), Inductance (L), Capacitance (C), AC Resistance (Rac), Quality Factor (Q),
Dissipation Factor (D), Admittance (Y), Conductance (G), Reactance (X), Susceptance (B), DC Resistance (Rdc)

C + R, C + D, C + Q, L + R, L + Q, L + D

X + R, X + D, X + Q

C + G, B + G, B + D, B + Q, B + R, L + G

Z + Phase Angle, Y + Phase Angle

1 ~ 256 times

320 x 240 DOT-MATRIX

RS-232C, GPIB

AC 115V (+10%/-25%), AC 230V (+15% / -14%)(Selectable), 50/60Hz

330(W) x 170(H) x 340(D)mm, Approx. 5kg

Specifications subject to change without notice.

CR-8000GGD2DH

STANDARD ACCESSORIES

User manual x 1
Power cord x 1
Test lead LCR-12 x 1

OPTIONAL ACCESSORIES SELECTION GUIDE

Accessory Model

LCR-05
LCR-06A
LCR-07
LCR-08
LCR-09
LCR-12
LCR-13
GTL-232
GRA-404

Note " " means the accessories work with a frequency limitation (under 1MHz)

Global Headquarters

GOOD WILL INSTRUMENT CO., LTD.

No. 7-1, Jhongsing Road, Tucheng City, Taipei County 236, Taiwan
T [phone] F [phone]
E-mail: [e-mail]

China Subsidiary

GOOD WILL INSTRUMENT (SUHZOU) CO., LTD.

NO. 69, Lushan Road, Snd, Suzhou Jiangsu 215011 China
T [phone] F [phone]

E-mail: [e-mail]

Malaysia Subsidiary

GOOD WILL INSTRUMENT (M) SDN. BHD.

27, Persiaran Mahsuri 1/1, Sunway Tunas,
11900 Bayan Lepas, Penang, Malaysia
T [phone] F [phone]
E-mail: [e-mail]

Test Fixture for axial & radial lead components

Test Lead with Kelvin clip (4 wire type)

Test Lead with Alligator clip (2 wire type)

Test Fixture (Tweezers) for SMD/Chip components

Test Fixture for SMD/Chip components

Test Lead with Kelvin clip (4 wire type)

Test Fixture for SMD/Chip components

RS-232C Cable

Rack Adapter Panel (19", 4U)

LCR-06ALCR-05 LCR-07 LCR-08 LCR-09

Brief Description

U.S.A. Subsidiary

INSTEK AMERICA CORP.

3661 Walnut Avenue Chino, CA 91710, U.S.A.
T [phone] F [phone]
E-mail: [e-mail]

Japan Subsidiary

INSTEK JAPAN CORPORATION

4F, Prosper Bldg, 1-3-3 Iwamoto-Cho Chiyoda-Ku,
Tokyo 101-0032 Japan
T [phone] F [phone]
E-mail: [e-mail]

Korea Subsidiary

GOOD WILL INSTRUMENT KOREA CO., LTD.

Room No.805, Ace Hightech-City B/D 1Dong,
Mullae-Dong 3Ga 55-20, Yeongduengpo-Gu, Seoul, Korea
T [phone] F [phone]
E-mail : [e-mail]

LCR-8110G LCR-8105G LCR-8101G

LCR-13 LCR-12

Made to Measure

Since 1975

www.gwinstek.com

Simply Reliable

Our low TCO helps you control costs
with reliable products and services.