How it Works
GSI
Loading...
PNEG-221
User Manual
38 pgs2.4 Mb0
Table of contents
Loading...

GSI PNEG-221 User Manual

Download
Page 1
PNEG-221
42' Diameter Bins Cor-Lok and Cut-Lok Flooring and Grandstand Layout
Installation Manual
PNEG-221
Date: 09-25-12
Page 2
Page 3
Table of Contents
SEE PAGE 28 AND PAGE 29 FOR 20 GAUGE
FLOOR SUPPORT REQUIREMENTS.

Contents

Chapter 1 Safety .....................................................................................................................................................4
Safety Guidelines .................................................................................................................................. 4
Safety Instructions ..................... ... .... .......................................... ... ........................................................ 5
Chapter 2 Recommended Method for Full Floor Installation .............................................................................7
Fan Placement Diagram ....................................................................................................................... 7
Grain Systems Recommended Method for Full Floor Installation ......................................................... 8
Installing the Undersplice .................................... ... ... .... ... ... ... .... ... ...................................................... 10
Chapter 3 Grandstand Identification .................... ....................................................... .......................................12
20 Gauge Grandstand Identification .......................................... ... ... ... ... .... ... ... ... .... ... ... ... ... .... ... ......... 12
Chapter 4 Flashing Installation ............................. ....................... ...................... .................................................13
Grain Systems Formed Flashing Installation ...................................................................................... 13
Chapter 5 Grandstand Layout at Center Well for Recirculating System ........................................................14
Chapter 6 Well Installation Cut Detail ................................................................................................................15
Well Installation Plank Cut Detail for 42', 48' and 60' Split Floor ......................................................... 15
Chapter 7 42' Cut-Lok/Cor-Lok Plank Order ........................... .... ... ... ... .... ... ... ....................................................16
42' Cut-Lok/Cor-Lok Plank Order ........................................................................................................ 16
Chapter 8 Plank Lengths .....................................................................................................................................17
Optional 42' 3' Split Plank Length ....................................................................................................... 18
Chapter 9 42' Grandstand Layout for Recirculating System .... ... ... ... .... ... ... ... ... .... ... ... ... .... ... ... ... ... .... ... ... .......19
42' 20 Gauge Grandstand Layout for Recirculating System Cut-Lok or 18 Gauge Cor-Lok Floors .... 19
Chapter 10 42' Grandstand Layouts, 33' Maximum Wall Height ............................... ... ... .... ... ... ... ... .... .............20
42' Cor-Lok/Cut-Lok and 20 Gauge Grandstand Layout
2.66" Corrugated Bins 5 Rings .......................................................................................................... 20
42' Cor-Lok/Cut-Lok and 20 Gauge Grandstand Layout
2.66'' Corrugated Bins 6 Rings and 4.00" Corrugated Bins 4 Rings and 5 Rings ............................. 21
42' Cor-Lok/Cut-Lok and 20 Gauge Grandstand Layout
2.66" Corrugated Bins 7 Rings .......................................................................................................... 22
42' Cor/Cut-Lok and 20 Gauge Grandstand Layout
2.66" Corrugated Bins 8 Rings and 4.00" Corrugated Bins 6 Rings .................................................. 23
42' Cor-Lok/Cut-Lok and 20 Gauge Grandstand Layout
2.66" Corrugated Bins 9 Rings .......................................................................................................... 24
42' Cor-Lok/Cut-Lok and 20 Gauge Grandstand Layout
2.66" Corrugated Bins 10 Rings and 4.00" Corrugated Bins 7 Rings ................................................ 25
42' Cor-Lok/Cut-Lok and 20 Gauge Grandstand Layout
2.66" Corrugated Bins 11 Rings and 4.00" Corrugated Bins 8 Rings ................................................ 26
42' Cor-Lok/Cut-Lok and 20 Gauge Grandstand Layout
2.66" Corrugated Bins 12 Rings and 4.00" Corrugated Bins 9 Rings ................................................ 27
Chapter 11 20 Gauge Floor Support Requirements .........................................................................................28
20 Gauge Grandstand Chart - 2.66" Corrugation .............................................................................. 28
20 Gauge Grandstand Chart - 4.00" Corrugation .............................................................................. 29
Chapter 12 Flashing Support at Stiffeners ........................................................................................................30
Stiffener Flashing Support Instructions for Internal Universal Stiffeners ........................................... 30
Chapter 13 Air Flow Support Instructions .........................................................................................................31
Installation of Air Flow Supports ........................................................................................................ 31
Chapter 14 Warranty ..........................................................................................................
PNEG-221 42' Cor-Lok and Cut-Lok Flooring 3
..................................37
Page 4

1. Safety

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE is used to address practices not related to personal injury.
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
Safety Guidelines
This manual contains information that is important for you, the owner/operator, to know and understand. This information relates to protecting personal safety and preventing equipment problems. It is the responsibility of the owner/operator to inform anyone operating or working in the area of this equipment of these safety guidelines. To help you recognize this information, we use the symbols that are defined below. Please read the manual and pay attention to these sections. Failure to read this manual and its safety instructions is a misuse of the equipment and may lead to serious injury or death.
DANGER
WARNING
CAUTION
NOTICE
Page 5
1. Safety
Follow Safety Instructions
Carefully read all safety messages in this manual and safety signs on your machine. Keep signs in good condition. Replace missing or damaged safety signs. Be sure new equipment components and repair parts include the current safety signs. Replacement safety signs are available from the manufacturer.
Learn how to operate the machine and how to use controls properly. Do not let anyone operate without instruction.
Keep your machinery in proper working condition. Unauthorized modifications to the machine may impair the function and/or safety and affect machine life.
If you do not understand any part of this manual or need assistance, contact your dealer.
Read and Understand Manual
Rotating Flight
Grain augers can kill or dismember. Keep clear of all augers and never enter the bin unless all
power is disconnected and locked out. Failure to do so will result in serious injury or death.
Rotating Flight
Safety Instructions
Our foremost concern is your safety and the safety of others associated with this equipment. We want to keep you as a customer. This manual is to help you understand safe operating procedures and some problems that may be encountered by the operator and other personnel.
As owner and/or operator, it is your responsibility to know what requirements, hazards, and precautions exist, and to inform all personnel associated with the equipment or in the area. Safety precautions may be required from the personnel. Avoid any alterations to the equipment. Such alterations may produce a very dangerous situation where SERIOUS INJURY or DEATH may occur.
This equipment shall be installed in accordance with the current installation codes and applicable regulations, which should be carefully followed in all cases. Authorities having jurisdiction should be consulted before installations are made.
PNEG-221 42' Cor-Lok and Cut-Lok Flooring 5
Page 6
1. Safety
Prepare for Emergencies
Be prepared if fire starts. Keep a first aid kit and fire extinguisher handy. Keep emergency numbers for doctors, ambulance service,
hospital, and fire department near your telephone.
Keep Emergency Equipment Quickly Accessible
Eye Protection
Gloves
Steel-Toed Boots
Respirator
Hard Hat
Fall Protection
Wear Protective Clothing
Wear close-fitting clothing and safety equipment appropriate to the job.
Remove all jewelry.
Tie long hair up and back.
Wear safety glasses at all times to protect eyes from debris.
Wear gloves to protect your hands from sharp edges on plastic or steel parts.
Wear steel-toed boots to help protect your feet from falling debris. Tuck in any loose or dangling shoestrings.
A respirator may be needed to prevent breathing potentially toxic fumes and dust.
Wear a hard hat to help protect your head.
Wear appropriate fall protection equipment when working at elevations greater than six feet (6').
Page 7

2. Recommended Method for Full Floor Installation

Fan Placement Diagram
For uniform air flow, place the fans in relation to the unloading tube as shown in Figure 2A. Floor planks should be perpendicular to the unloading tube.
Figure 2A
PNEG-221 42' Cor-Lok and Cut-Lok Flooring 7
Page 8
2. Recommended Method for Full Floor Installation
Chalked lines referred to Step 2.
Grain Systems Recommended Method for Full Floor Installation
Using the GSI recommended method for full floor installation should save construction time and eliminate the problem of improper installation which could invalidate your warranty. Note the following dimensions as shown in Figure 2B.
• Dimension “A” is the leg-to-leg spacing along the centerline of a given plank.
• Dimension “B” is the amount of stagger between supports under adjacent planks and is half of Dimension “A”.
• Dimension “C” is the distance from the center of the unload auger to the nearest rows of supports and is half of Dimension “B”.
Dimensions “A”, “B” and “C” are shown on the appropriate grandstand layout for wall heights under 32 feet. For taller bins, grandstand quantity as well as dimensions “A” and “B” are given on Page 28 and
Page 29 for 20 gauge.
1. Layout centerlines of tank. Make sure one centerline is in line with the direction of the flooring planks while the other centerline is perpendicular with the flooring planks. See Figure 2B.
2. From the centerline that is perpendicular to the flooring planks, measure the distance of “C” Dimension and mark a chalk line. See Figure 2B.
3. From the line chalked in the previous step, measure over the distance of “B” Dimension and chalk another line. Repeat this procedure across the bin until reaching the wall in both directions. When completed, there should be a set of parallel lines (perpendicular to the floor planks) with “B” Dimension distance between each line. See Figure 2B.
Figure 2B
Page 9
2. Recommended Method for Full Floor Installation
IMPORTANT: First piece of flooring must start at
the proper distance from centerline of bin. Refer to floor layout on Page 16. First piece may need to be trimmed for length to fit at the proper location.
Figure 2C
4. Install flooring starting at the bin wall on the opposite side of the unload auger. Floor planks should be placed perpendicular to the unload auger with the outside edge the correct distance from the center of the bin. and the open channel edge is facing towards the center of the bin.
(See Figure 7A on Page 16.)
Be sure the flat edge of the floor plank is facing the bin wall
(See Figure 2C.)
Position the supports for the first/shortest floor plank according to the number of bin rings and corrugation as shown in the illustrations to flooring and bin wall to hold plank in place. (
on Pages 19-27
or stated in the charts on
See Page 13
for flashing installation.)
Page 28-29
. Attach the flashing
5. POSITION THE NEXT ROW OF SUPPORTS ACCORDING TO THE CHALK LINES and support layout. The straight tab should “snap” under the first (previous) floor piece. After the supports in the row are correctly positioned, install the next floor piece by hooking the open channel edge under the outside hooks of the floor supports. Push down sharply on the edge of the floor piece until it snaps into the previous floor piece. (See Figure 2C.) Continue this process for the rest of the floor cutting planks for center and intermediate wells as needed. See Figure 5A on Page 14 for center well support locations.
NOTE: Whenever there is more than Dimension “B” divided by three inches (B/3") of plank unsupported
beside the bin wall, there should be a support on that plank or a support on each of the planks adjacent to it such that no more than Dimension “B” divided by three inches (B/3") is unsupported. For example: 2.66" bin with 8 rings has a “B” dimension of 22". Take 22"/3" = 7.33" (Round to 7"). Therefore, there should be no more than 7" of unsupported floor plank.
PNEG-221 42' Cor-Lok and Cut-Lok Flooring 9
Page 10
2. Recommended Method for Full Floor Installation
Installing the Undersplice
The undersplice should be installed underneath the planks at the split after both plank lengths have been butted together. Each splice has to be laid as each row of planks are laid rather than after all have been placed. Figure 2D shows the layout of the undersplice plates a nd t he screw pattern used to secure them.
Figure 2D Pattern for Fastening Splice to Planks
Page 11
2. Recommended Method for Full Floor Installation
Installation Instructions
1. When a splice is needed, plank length A as described in the floor manual should be installed alongside plank length B.
2. The undersplice should then be installed under the split of plank A and B. The splice sho uld extend 3" under each plank. The splice should be screwed in place as shown in Figure 2D on Page 10.
3. This process will be repeated for all plank locations requiring a splice.
Figure 2E
PNEG-221 42' Cor-Lok and Cut-Lok Flooring 11
Page 12

3. Grandstand Identification

20 Gauge Grandstand Identification
20 Gauge
Plenum Clearance Grandstand Color Code
11-7/8" Blue 14-3/8" White
17-3/16" Yellow
Figure 3A
Page 13
Figure 4A

4. Flashing Installation

Grain Systems Formed Flashing Installation
If a bin sweep auger will be used, overlap flashing so that the sweep with climb up on to the next flashing section when rotating (usually clockwise). (See Figure 4A.) This will prevent the rotating/slipping outer wheel of the sweep from catching on the flashing edges. (All GSI power sweeps and carry-in sweeps
manufactured after April 2002 run clockwise.)
After floor is in place, place 1-1/4" bolts through pre-punched holes in sidewall. Bolt heads should be on outside of bin. See Figure 4B to determine the correct sequence for placing the nuts and washers. Finger tighten the nuts until all flashing is installed, then go back and fully tighten. While holding the flashing flat and pushing in towards the bin wall, fasten the flashing to the floor with two sheet metal screws.
Figure 4B
PNEG-221 42' Cor-Lok and Cut-Lok Flooring 13
Page 14

5. Grandstand Layout at Center Well for Recirculating System

Support all center wells to concrete.
CAUTION
Figure 5A
Page 15

6. Well Installation Cut Detail

Support all center wells to concrete.
CAUTION
Well Installation Plank Cut Detail for 42', 48' and 60' Split Floor
Figure 6A
PNEG-221 42' Cor-Lok and Cut-Lok Flooring 15
Page 16

7. 42' Cut-Lok/Cor-Lok Plank Order

Support all center wells to concrete.
CAUTION
42' Cut-Lok/Cor-Lok Plank Order
Figure 7A
Page 17

8. Plank Lengths

The following plank lengths start at the sidewall and work towards the center of the bin.
Reference grandstand layout on Pages 20-27 for floor drawing.
Feet and Inches Total Inches
8'-5" 101"
12'-10" 154"
16'-0" 192" 18'-7" 223" 20'-9" 249"
Feet and Inches Total Inches Feet and Inches Total Inches
12'-4" 148'' 10'-4" 124'' 13'-2" 158'' 11'-2" 134''
13'-10" 166'' 11'-10" 142''
14'-7" 175'' 12'-6" 150'' 15'-2" 182'' 13'-2" 158''
15'-10" 190'' 13'-9" 165''
16'-4" 196'' 14'-4" 172''
16'-10" 202'' 14'-10" 178''
17'-4" 208'' 15'-4" 184'' 17'-9" 213'' 15'-9" 189'' 18'-2" 218'' 16'-2" 194'' 18'-7" 223'' 16'-7" 199''
18'-11" 227'' 16'-11" 203''
19'-3" 231'' 17'-3" 207'' 19'-7" 235'' 17'-7" 211''
19'-10" 238'' 17'-10" 214''
20'-1" 241'' 18'-1" 217'' 20'-4" 244'' 18'-4" 220'' 20'-7" 247'' 18'-7" 223'' 20'-9" 249'' 18'-9" 225''
20'-11" 251'' 18'-11" 227''
21'-1" 253'' 19'-1" 229'' 21'-2" 254'' 19'-2" 230'' 21'-4" 256'' 19'-4" 232'' 21'-5" 257'' 19'-5" 233'' 21'-5" 257'' 19'-5" 233'' 21'-6" 258'' 19'-6" 234'' 21'-7" 259'' 19'-7" 235'' 21'-7" 259'' 19'-7" 235'' 21'-7" 259'' 19'-7" 235''
PNEG-221 42' Cor-Lok and Cut-Lok Flooring 17
Page 18
8. Plank Lengths
Optional 42' 3' Split Plank Length
42' 3' Split Plank Length
Feet and Inches Total Inches
8'-5" 101"
12'-10" 154"
16'-0" 192" 18'-7" 223" 20'-9" 249"
Feet and Inches Total Inches Feet and Inches Total Inches
14'-4" 172" 8'-4" 100" 15'-2" 182" 9'-2" 110"
15'-10" 190" 9'-10" 118"
16'-6" 198" 10'-6" 126" 17'-2" 206" 11'-2" 134" 17'-9" 213" 11'-9" 141" 18'-4" 220" 12'-4" 148"
18'-10" 226" 12'-10" 154"
19'-4" 232" 13'-4" 160" 19'-9" 237" 13'-9" 165" 20'-2" 242" 14'-2" 170" 20'-7" 247" 14'-7" 175"
20'-11" 251" 14'-11" 179"
21'-3" 255" 15'-3" 183" 21'-7" 259" 15'-7" 187"
21'-10" 262" 15'-10" 190"
22'-1" 265" 16'-1" 193" 22'-1" 268" 16'-4" 196" 22'-7" 271" 16'-7" 199" 22'-9" 273" 16'-9" 201"
22'-11" 275" 16'-11" 203"
23'-1" 277" 17'-1" 205" 23'-2" 278" 17'-2" 206" 23'-4" 280" 17'-4" 208" 23'-5" 281" 17'-5" 209" 23'-5" 281" 17'-5" 209" 23'-6" 282" 17'-6" 210" 23'-7" 283" 17'-7" 211" 23'-7" 283" 17'-7" 211" 23'-7" 283" 17'-7" 211"
Page 19

9. 42' Grandstand Layout for Recirculating System

Support all center wells to concrete.
CAUTION
IMPORTANT: First piece of flooring must start at the proper distance from
center of bin. First few pieces may have to be trimmed for proper fit.
NOTE: Every other row to be staggered. Unsupported ends of floor pieces not to exceed 6 inches.
* 10 supports per tank were added for center well on Page 14.
42' 20 Gauge Grandstand Layout for Recirculating System Cut-Lok or 18 Gauge Cor-Lok Floors
2.66'' Corrugated Bins 8 Rings Maximum and
4.00" Corrugated Bins 6 Rings Maximum
Figure 9A
PNEG-221 42' Cor-Lok and Cut-Lok Flooring 19
Page 20

10. 42' Grandstand Layouts, 33' Maximum Wall Height

NOTE: Every other row to be staggered. Unsupported ends of floor pieces not to exceed 8 inches.
* 2 Supports per tank were added for center well (not shown on layouts).
Support all center wells to concrete.
CAUTION
IMPORTANT: First piece of flooring must start at the proper distance from
center of bin. First few pieces may have to be trimmed for proper fit.
42' Cor-Lok/Cut-Lok and 20 Gauge Grandstand Layout
2.66" Corrugated Bins 5 Rings
Figure 10A
Page 21
10. 42' Grandstand Layouts, 33' Maximum Wall Height
NOTE: Every other row to be staggered. Unsupported ends of floor pieces not to exceed 8 inches.
* 2 Supports per tank were added for center well (not shown on layouts).
Support all center wells to concrete.
CAUTION
IMPORTANT: First piece of flooring must start at the proper distance from
center of bin. First few pieces may have to be trimmed for proper fit.
42' Cor-Lok/Cut-Lok and 20 Gauge Grandstand Layout
2.66'' Corrugated Bins 6 Rings and
4.00" Corrugated Bins 4 Rings and 5 Rings
Figure 10B
PNEG-221 42' Cor-Lok and Cut-Lok Flooring 21
Page 22
10. 42' Grandstand Layouts, 33' Maximum Wall Height
NOTE: Every other row to be staggered. Unsupported ends of floor pieces not to exceed 7 inches.
* 2 Supports per tank were added for center well (not shown on layouts).
Support all center wells to concrete.
CAUTION
IMPORTANT: First piece of flooring must start at the proper distance from
center of bin. First few pieces may have to be trimmed for proper fit.
42' Cor-Lok/Cut-Lok and 20 Gauge Grandstand Layout
2.66" Corrugated Bins 7 Rings
Figure 10C
Page 23
10. 42' Grandstand Layouts, 33' Maximum Wall Height
NOTE: Every other row to be staggered. Unsupported ends of floor pieces not to exceed 7 inches.
* 2 Supports per tank were added for center well (not shown on layouts).
Support all center wells to concrete.
CAUTION
IMPORTANT: First piece of flooring must start at the proper distance from
center of bin. First few pieces may have to be trimmed for proper fit.
42' Cor/Cut-Lok and 20 Gauge Grandstand Layout
2.66" Corrugated Bins 8 Rings and 4.00" Corrugated Bins 6 Rings
Figure 10D
PNEG-221 42' Cor-Lok and Cut-Lok Flooring 23
Page 24
10. 42' Grandstand Layouts, 33' Maximum Wall Height
NOTE: Every other row to be staggered. Unsupported ends of floor pieces not to exceed 7 inches.
* 2 Supports per tank were added for center well (not shown on layouts).
IMPORTANT: First pie ce of flooring must start at the proper distance from
center of bin. First few pieces may have to be trimmed for proper fit.
Support all center wells to concrete.
CAUTION
42' Cor-Lok/Cut-Lok and 20 Gauge Grandstand Layout
2.66" Corrugated Bins 9 Rings
Figure 10E
Page 25
10. 42' Grandstand Layouts, 33' Maximum Wall Height
NOTE: Every other row to be staggered. Unsupported ends of floor pieces not to exceed 6 inches.
* 2 Supports per tank were added for center well (not shown on layouts).
IMPORTANT: First piece of flooring must start at the proper distance from
center of bin. First few pieces may have to be trimmed for proper fit.
Support all center wells to concrete.
CAUTION
42' Cor-Lok/Cut-Lok and 20 Gauge Grandstand Layout
2.66" Corrugated Bins 10 Rings and
4.00" Corrugated Bins 7 Rings
Figure 10F
PNEG-221 42' Cor-Lok and Cut-Lok Flooring 25
Page 26
10. 42' Grandstand Layouts, 33' Maximum Wall Height
NOTE: Every other row to be staggered. Unsupported ends of floor pieces not to exceed 6 inches.
* 2 Supports per tank were added for center well (not shown on layouts).
IMPORTANT: First piece of flooring must start at the proper distance from
center of bin. First few pieces may have to be trimmed for proper fit.
Support all center wells to concrete.
CAUTION
42' Cor-Lok/Cut-Lok and 20 Gauge Grandstand Layout
2.66" Corrugated Bins 11 Rings and
4.00" Corrugated Bins 8 Rings
Figure 10G
Page 27
10. 42' Grandstand Layouts, 33' Maximum Wall Height
NOTE: Every other row to be staggered. Unsupported ends of floor pieces not to exceed 5 inches.
* 2 Supports per tank were added for center well (not shown on layouts).
IMPORTANT: First piece of flooring must start at the proper distance from
center of bin. First few pieces may have to be trimmed for proper fit.
Support all center wells to concrete.
CAUTION
42' Cor-Lok/Cut-Lok and 20 Gauge Grandstand Layout
2.66" Corrugated Bins 12 Rings and
4.00" Corrugated Bins 9 Rings
Figure 10H
PNEG-221 42' Cor-Lok and Cut-Lok Flooring 27
Page 28

11. 20 Gauge Floor Support Requirements

SUPPORT SPACING
SUPPORT QUANTITY
All floor styles OK for
bin sizes in upper
shaded area.
Floor styles list in order of
increasing strength 20 Gauge COR-LOK 18 Gauge COR-LOK
CUT-LOK
20 Gauge Grandstand Chart - 2.66" Corrugation
Narrow/2.66" Corrugation - 20 Gauge Grandstand Floor Support Chart
Full Floor Supports Required for Plank Type Flooring 2.66" Corrugation
Dia. 12 15 18 21 24 27 30 33 36 39 42 45 48 54 60 72 75 78 90 105
Rings
57/27
3
62
54/276258/298054/27
4
54/276258/298054/27
5
54/276254/278854/27
6
54/276252/269648/24
7
48/247048/24
8
48/247048/24
9
42/217542/21
10
42/217542/21
11
38/198040/20
12
38/198038/19
13
34/179034/17
14
32/169532/16
15
30/15
16
100
28/14
17
106
26/13
18
110
19
20
21
22
23
CUT-LOK only if
24
Dia. and number of
rings are in bottom
25
26
27
28
29
shaded area.
100
100
110
110
115
120
130
140
30/15
150
28/14
160
26/13
170
24/12
180
22/11
190
120
120
120
138
48/24
144
42/21
144
42/21
144
42/21
144
40/20
154
38/19
166
34/17
180
32/16
190
30/15
205
28/14
215
24/12
240
24/12
240
22/11
260
52/26
160
52/26
160
50/25
168
46/23
182
42/21
190
42/21
190
42/21
190
40/20
202
36/18
220
34/17
230
32/16
250
30/15
260
26/13
290
24/12
310
22/11
340
22/11
340
20/10
370
18/9
400
18/9
400
16/8
450
14/7
500
56/28
205
52/26
215
48/24
225
46/23
230
42/21
243
42/21
250
40/20
265
38/19
280
36/18
290
34/17
300
32/16
320
28/14
360
26/13
380
24/12
400
22/11
440
22/11
440
20/10
470
18/9
520
18/9
520
16/8
580
14/7
650
*For Aeration Systems recessed in the concrete, add 1 ring for proper spacing. When using FL-3102-3 or FL-3102-6 (3", 6") Grandstands, increase the listed quantities by 33%
(Standard Quantity x 1.33). Quantities of Grandstands are minimum required for installation - Due to varying conditions
and construction techniques at floor and wall penetrations, additional supports may need to be ordered.
How to read the chart: For example, a 12' diameter bin with 7 rings would have spacing of 54/27 (the top
numbers). Meaning A=54" and B=27". The number of supports needed would be 62, (the bottom number).
(* Based upon 13.5" or taller floor heights)
54/27
54/27
50/25
50/25
249
48/24
275
48/24
275
46/23
300
44/22
303
42/21
309
40/20
319
38/19
345
36/18
360
34/17
380
32/16
400
28/14
450
26/13
480
24/12
510
22/11
550
22/11
550
20/10
600
18/9
660
16/8
730
16/8
730
14/7
820
14/7
820
12/6
950
12/6
950
12/6
950
304
50/25
333
48/24
347
44/22
363
42/21
387
40/20
397
38/19
417
36/18
441
34/17
470
32/16
500
30/15
520
28/14
550
26/13
590
24/12
630
22/11
680
20/10
740
20/10
740
18/9
810
16/8
900
16/8
900
14/7
1010
14/7
1010
12/6
1160
12/6
1160
12/6
1160
390
50/25
390
46/23
425
44/22
435
42/21
465
40/20
479
36/18
525
34/17
550
32/16
600
30/15
630
28/14
670
28/14
670
26/13
710
24/12
760
22/11
820
20/10
890
20/10
890 18/9
970 16/8
1080
16/8
1080
14/7
1220
14/7
1220
12/6
1410
12/6
1410
12/6
1410
470
48/24
487
44/22
523
44/22
523
40/20
565
38/19
597
36/18
620
34/17
659
32/16
710
30/15
750
28/14
790
26/13
840
24/12
900
24/12
900
22/11
970
20/10
1060
20/10
1060
18/9
1160
16/8
1290
16/8
1290
14/7
1450
14/7
1450
12/6
1670
12/6
1670
12/6
1670
50/25
576
48/24
586
46/23
606
44/22
624
42/21
656
38/19
716
36/18
746
34/17
786
30/15
880
28/14
930
26/13
990
24/12
1060
24/12
1060
22/11
1140
22/11
1140
20/10
1240
20/10
1240
18/9
1360
16/8
1510
16/8
1510
14/7
1700
14/7
1700
12/6
1960
12/6
1960
12/6
1960
46/23
46/23
806
44/22
836
42/21
866
40/20
906
36/18
986
34/17
1036
32/16
1096
30/15
1160
26/13
1310
24/12
1400
24/12
1400
22/11
1510
20/10
1640
20/10
1640
18/9
1800
18/9
1800
16/8
2000
16/8
2000
16/8
2000
14/7
2260
14/7
2260
12/6
2600
12/6
2600
46/23
909
44/22
933
42/21
977
40/20
1019
36/18
1109
34/17
1163
32/16
1230
28/14
1390
26/13
1480
24/12
1590
22/11
1710
20/10
1860
20/10
1860
18/9
2040
18/9
2040
16/8
2270
16/8
2270
16/8
2270
14/7
2560
14/7
2560
14/7
2560
12/6
2950
12/6
2950
695
44/22
735
42/21
750
40/20
790
38/19
820
34/17
900
32/16
950
30/15
1010
28/14
1070
26/13
1140
24/12
1220
22/11
1320
22/11
1320
20/10
1430
20/10
1430
18/9
1570
18/9
1570
16/8
1740
16/8
1740
14/7
1960
14/7
1960
12/6
2260
12/6
2260
SUPPORT SPACING SUPPORT QUANTITY
44/22
1196
42/21
1236
40/20
1296
38/19
1346
34/17
1486
32/16
1566
30/15
1660 1660
1760
26/13
1870
24/12
2000
22/11
2160
20/10
2350
18/9
2570
18/9
2570
16/8
2860
16/8
2860
16/8
2860
14/7
3230
14/7
3230
14/7
3230
12/6
3720
12/6
3720
12/6
3720
44/22
1430
42/21
1477
40/20
1544
36/18
1697
34/17
18 Gauge COR-LOK or CUT-LOK
1779
if Dia. and number of rings are in
32/16
1883
30/15
1993
26/13
2300
24/12
2460
22/11
2650
20/10
2880
20/10
2880
18/9
3170
16/8
3520
16/8
3520
14/7
3970
14/7
3970
14/7
3970
12/6
4570
12/6
4570
12/6
4570
12/6
4570
middle unshaded area.
26/13
26/13
3300
24/12
3540
22/11
3820
22/11
3820
20/10
4150
18/9
4550
16/8
5060
16/8
5060
14/7
5710
14/7
5710
12/6
6580
12/6
6580
12/6
6580
Corrugated floors and monorail
supports are required if Dia. and
number of rings are in bottom
26/13
3580
3870
24/12
24/12
3840
4150
22/11
22/11
4150
4480
20/10
20/10
4500
4870
20/10
18/9
4500
5340
18/9
18/9
4950
5340
16/8
16/8
5500
5940
16/8
16/8
5500
5940
14/7
14/7
6200
6710
14/7
14/7
6200
6710
12/6
12/6
7140
7730
12/6
12/6
7140
7730
12/6
7140
unshaded area.
24/12
5520
22/11
5960
20/10
6480
18/9
7120
18/9
7120
16/8
7910
16/8
7910
14/7
8920
14/7
8920
12/6
10280
12/6
10280
22/11
8110
20/10
8820
18/9
9680
18/9
9680
16/8
10760
16/8
10760
14/7
12150
14/7
12150
12/6
13990
12/6
13990
Page 29
11. 20 Gauge Floor Support Requirements
20 Gauge Grandstand Chart - 4.00" Corrugation
Wide/4.00" Corrugation - 20 Gauge Grandstand Floor Support Chart
Full Floor Supports Required for Plank Type Flooring 4.00" Corrugation
Dia. 12 15 18 21 24 27 30 33 36 39 42 45 48 54 60 72 75 78 90 105
Rings
SUPPORT SPACING
SUPPORT QUANTITY
54/276258/298054/27
3
54/276254/278854/27
4
54/276252/269648/24
5
48/247048/24
6
42/217542/21
7
42/217542/21
8
38/198040/20
9
36/189034/17
10
32/169530/15
11
28/14
12
100
26/13
13
110
14
15
16
CUT-LOK only if Dia.
17
and number of rings
18
19
20
21
22
are in bottom shaded area.
100
110
110
115
130
150
28/14
160
26/13
170
120
120
138
48/24
138
42/21
144
42/21
144
38/19
166
34/17
180
32/16
190
28/14
210
26/13
220
22/11
260
52/26
150
52/26
160
50/25
168
46/23
182
42/21
190
42/21
190
38/19
220
34/17
230
32/16
250
28/14
280
26/13
290
22/11
340
20/10
370
18/9
400
56/28
202
52/26
214
48/24
224
46/23
230
42/21
249
40/20
265
38/19
277
34/17
300
32/16
320
28/14
360
24/12
400
22/11
440
20/10
480
18/9
520
16/8
580
16/8
580
54/27
48/24
48/24
44/22
42/21
40/20
36/18
34/17
32/16
28/14
24/12
22/11
20/10
(* Based upon 13.5" or taller floor heights)
50/25
50/25
50/25
249
275
275
303
309
319
355
380
400
450
510
550
600
18/9
660
16/8
730
16/8
730
14/7
820
12/6
950
12/6
950
333
50/25
333
48/24
347
44/22
363
42/21
387
38/19
417
34/17
471
32/16
500
30/15
520
28/14
550
24/12
630
22/11
680
20/10
740 18/9
810 16/8
900 16/8
900 14/7
1010
12/6
1160
12/6
1160
390
50/25
390
46/23
425
44/22
435
40/20
480
36/18
525
34/17
555
32/16
600
30/15
650
28/14
670
24/12
760
22/11
820
20/10
890
18/9
970
16/8
1080
16/8
1080
14/7
1220
12/6
1410
12/6
1410
470
50/25
470
44/22
523
44/22
523
40/20
565
36/18
620
32/16
695
30/15
750
28/14
790
26/13
840
24/12
900
20/10
1060
20/10
1060 18/9
1160 16/8
1290 16/8
1290 14/7
1450 12/6
1670 12/6
1670
50/25
576
50/25
576
46/23
606
42/21
656
40/20
686
36/18
746
32/16
830
28/14
930
26/13
990
24/12
1060
22/11
1140
20/10
1240
18/9
1360
18/9
1360
16/8
1510
16/8
1510
14/7
1700
12/6
1960
12/6
1960
46/23
695
46/23
695
46/23
695
42/21
751
38/19
821
34/17
900
32/16
951
30/15
1010
26/13
1140
24/12
1220 22/11
1320
20/10
1430
18/9
1570
18/9
1570
16/8
1750
16/8
1750
14/7
1970
12/6
2270
12/6
2270
52/26
735
48/24
775
44/22
836
42/21
866
38/19
946
34/17
1036
30/15
1156
28/14
1230
24/12
1400 22/11
1510
20/10
1640
18/9
1800
18/9
1800
16/8
2000
16/8
2000
16/8
2000
14/7
2260
12/6
2600
12/6
2600
48/24
869
48/24
869
44/22
933
42/21
977
38/19
1057
34/17
1163
30/15
1303
28/14
1390
24/12
1590
22/11
1710
20/10
1860
18/9
2040
16/8
2270
16/8
2270
16/8
2270
14/7
2560
14/7
2560
12/6
2950
12/6
2950
46/23
1156
42/21
1236
40/20
1296
36/18
1416
32/16
1566
30/15
1660
26/13
1870
24/12
2000
20/10
2350
18/9
2570
16/8
2860
16/8
2860
16/8
2860
14/7
3230
14/7
3230
12/6
3720
12/6
3720
All floor styles OK for
bin sizes in upper
shaded area.
44/22
1430
42/21
1477
38/19
1650
34/17
1779
32/16
1883
28/14
28/15
2160
3550
24/12
22/11
2460
3820
22/11
20/10
2650
4150
20/10
18/9
2880
4550
18/9
16/8
3170
5060
16/8
16/8
3520
5060
16/8
14/7
3520
5710
14/7
12/6
3970
6580
14/7
12/6
3970
6580
12/6
4570
12/6
4570
18 Gauge COR-LOK
or CUT-LOK if Dia.
and number of rings
are in middle
unshaded area.
24/12
24/12
4160
22/11
4480
20/10
4870
18/9
5340
16/8
5940
16/8
5940
14/7
6710
12/6
7730
12/6
7730
22/11 5970
20/10
6480
18/9
7120
16/8
7910
16/8
7910
14/7
8920
14/7
8920
12/6
10280
3850
22/11
4150
20/10
4500
18/9
4950
16/8
5500
16/8
5500
14/7
6200
12/6
7140
12/6
7140
20/10
8820
9680
10760
10760
12150
12150
13990
18/9
16/8
16/8
14/7
14/7
12/6
23
*For Aeration Systems recessed in the concrete, add 1 ring for proper spacing. When using FL-3102-3 or FL-3102-6 (3", 6") Grandstands, increase the listed quantities by 33%
(Standard Quantity x 1.33). Quantities of Grandstands are minimum required for installation - Due to varying conditions
and construction techniques at floor and wall penetrations, additional supports may need to be ordered.
How to read the chart: For example, a 12' diameter bin with 5 rings would have spacing of 54/27 (the top
numbers). Meaning A=54" and B=27". The number of supports needed would be 62, (the bottom number).
PNEG-221 42' Cor-Lok and Cut-Lok Flooring 29
Page 30

12. Flashing Support at Stiffeners

Stiffener Flashing Support Instructions for Internal
Universal Stiffeners
1. Install the floor and support system, cutting the floor to go around the internal stiffeners as required.
2. Break the stiffener flashing support (SS-6984) into its three (3) components.
3. Lay the flashing supports on top of the flooring and weld the flashing supports to the stiffener as close as possible. Fasten the flashing to the wall, flashing support and floor. Seal all spaces by welding or caulking.
4. Paint all welds with good quality zinc rich paint.
5. Stiffener flashing supports (SS-6984) must be ordered separately from the standard floor and flashing.
Figure 12A
Page 31

13. Air Flow Support Instructions

Installation of Air Flow Supports
1. Determine the spacing and quantity of air flow supports required from the chart on Page 33. Make sure that the correct supports have been ordered for use with the proper depth of plank (either 1-1/8" or 1-3/8" deep).
2. Mark center of bin.
3. Install discharge auger.
4. Mark spacing lines parallel to discharge auger.
5. Start on the side of the bin opposite from the discharge auger and place the first two (2) rows of supports on the spacing lines. Note that air flow supports are installed at an angle in an overlapp ing pattern so the ends will overlap. See floor layouts in Figure 13B on Page 34.
6. Install the channel lock flooring on the first two (2) rows of supports and secure in place with bin wall flashing.
7. Finish placing supports on the spacing lines and installing floor planks.
a. Single supports are used next to the bin wall and at the ends of split floor planks in order to
maintain the floor manufacturer’s recommended minimum distance from the end of a plank to a support.
b. Double supports are used at the sump and along the sides of the discharge auger for spacing of
16" or less and for recirculating bin equipment.
c. Full supports may have to be overlapped or angled to provide support at walls and to maintain
spacing and flashing requirements.
PNEG-221 42' Cor-Lok and Cut-Lok Flooring 31
Page 32
13. Air Flow Support Instructions
The following Figure 13A show methods of support placement to achieve the necessary spacing close to discharge augers and sumps.
Figure 13A
Page 33
13. Air Flow Support Instructions
*Installation, Spacing and Quantities of Air Flow Supports Under Channel Lock Floors
Bin Diameter - Number of Supports
Grain Depth at
Bin Wall (ft.)
18' 30" 34 2 8 48 2 10 60 2 12 84 2 14 88 2 14 24' 26" 36 2 8 56 2 10 74 2 12 92 2 14 104 2 14 27' 24" 44 2 8 62 2 10 76 2 12 92 2 14 112 2 14 32' 20" 54 2 10 64 2 12 84 2 14 106 2 16 130 2 18 40' 16" 58 10 14 80 12 16 104 14 18 128 16 20 160 18 22 48' 13" 72 10 16 98 12 20 126 14 22 158 16 24 190 18 28 53' 12" 76 10 18 106 12 22 140 14 24 172 16 28 210 18 30 68' 10" 86 10 22 116 12 26 156 14 28 212 16 32 250 18 36 16' 24" and 12" 68 10 8 82 12 10 104 14 12 120 16 14 140 18 14
(for Grain Flow)
Grain Depth at
Bin Wall (ft.)
18' 30" 116 2 16 136 2 18 172 2 20 Use 24" Spacing Use 24" Spacing 24' 26" 124 2 16 144 2 18 200 2 20 Use 24" Spacing Use 24" Spacing
Spacing
(in.)
Spacing
(in.)
18 Ft. Dia. 21 Ft. Dia. 24 Ft. Dia. 27 Ft. Dia. 30 Ft. Dia.
Full Double Single Full Double Single Full Double Single Full Double Single Full Double Single
Bin Diameter - Number of Supports
33 Ft. Dia. 36 Ft. Dia. 42 Ft. Dia. 48 Ft. Dia. 60 Ft. Dia.
Full Double Single Full Double Single Full Double Single Full Double Single Full Double Single
27' 24" 136 2 16 154 2 18 212 2 20 274 2 22 422 2 30 32' 20" 150 2 20 184 2 22 242 2 26 326 2 28 498 2 36 40' 16" 192 20 24 234 22 28 314 24 32 410 28 36 620 34 46 48' 13" 238 20 30 278 22 34 368 24 38 488 28 44 762 34 56 53' 12" 262 20 34 306 22 36 416 24 42 534 28 48 838 34 60 68' 10" 296 20 40 356 22 44 478 24 50 652 28 58 1024 34 72 16' 24" and 12" 168 20 16 188 20 18 264 24 20 350 28 20 N/A N/A N/A
(for Grain Flow)
NOTES:
1. Use a maximum spacing of 16" for perforated corrugated flooring.
2. The number of supports listed is based on the maximum peaked capacity of each bin.
3. Use extra single supports for split floors.
4. Extra supports are required for grain recirculating equipment. Use the manufacturer’s recommendation for the number and spacing of extra supports. NOTE: For grain flows, air flow
supports are doubled in a 14' diameter in the center of the floor.
5. Contact a representative for air flow supports required for larger bins and deeper grain depths.
6. *Increase the number of supports by 5% when used with 6-3/4" wide mfs floor planks.
PNEG-221 42' Cor-Lok and Cut-Lok Flooring 33
Page 34
13. Air Flow Support Instructions
Figure 13B
Page 35
13. Air Flow Support Instructions
Installation, Spacing and Quantities of Air Flow Supports Under
Channel Lock Floors York and Chief Bins
Bin Diameter - Number of Supports
Grain Depth at
Bin Wall (ft.)
18' 30" 26 2 8 36 2 8 50 2 10 64 2 12 80 2 14 24' 26" 30 2 8 42 2 8 56 2 10 74 2 12 92 2 14 27' 24" 32 2 8 44 2 8 60 2 10 78 2 12 98 2 14 32' 20" 38 2 10 52 2 10 72 2 12 92 2 14 116 2 16 40' 16" 46 10 14 64 12 14 86 14 16 114 14 18 142 16 20 48' 13" 54 10 16 78 12 16 106 14 20 136 14 22 172 16 24 53' 12" 58 10 18 84 12 18 114 14 22 148 14 24 184 16 28 68' 10" 70 10 22 98 12 22 134 14 26 174 14 28 220 16 32 16' 24" and 12" 60 10 8 72 12 8 88 14 10 106 14 12 126 16 14
(for Grain Flow)
Spacing
(in.)
15' 6" 18' 7" 21' 8" 24' 9" 27' 10"
Full Double Single Full Double Single Full Double Single Full Double Single Full Double Single
Bin Diameter - Number of Supports
Grain Depth at
Bin Wall (ft.)
18' 30" 98 2 14 116 2 16 136 2 18 160 2 20 182 2 22 24' 26" 112 2 14 132 2 16 154 2 18 182 2 20 208 2 22 27' 24" 120 2 14 142 2 16 166 2 18 196 2 20 224 2 22 32' 20" 140 2 18 168 2 20 198 2 22 232 2 26 260 2 26 40' 16" 174 18 22 208 20 24 244 22 28 286 24 32 330 26 32 48' 13" 210 18 28 252 20 30 298 22 34 350 24 38 402 26 38 53' 12" 228 18 30 272 20 34 316 22 36 378 24 42 434 26 42 68' 10" 270 18 36 324 20 40 384 22 44 450 24 50 520 26 50 16' 24" and 12" 148 18 14 170 20 16 194 22 18 224 24 20 252 26 22
(for Grain Flow)
Spacing
(in.)
Grain Depth at
Bin Wall (ft.)
Full Double Single Full Double Single Full Double Single Full Double Single Full Double Single
18' 24" 288 2 28 362 2 32 444 2 36 24' 20" 346 2 28 436 2 32 536 2 36 27' 20" 346 2 28 436 2 32 536 2 36
31' 34' 37' 1" 40' 3" 43' 4"
Bin Diameter - Number of Supports
Spacing
(in.)
Full Double Single Full Double Single Full Double Single
49' 6" 55' 8" 61' 10"
32' 20" 346 2 28 436 2 32 536 2 36 40' 16" 428 28 36 540 32 42 664 36 46 48' 13" 524 28 44 660 32 52 812 36 56 53' 12" 566 28 48 714 32 54 878 36 60 68' 10" 676 28 58 852 32 68 1050 36 72
PNEG-221 42' Cor-Lok and Cut-Lok Flooring 35
Page 36
13. Air Flow Support Instructions
Installation, Spacing and Quantities of Air Flow Supports Under
Channel Lock Floors Behlen Bins
Bin Diameter - Number of Supports
Grain Depth at
Bin Wall (ft.)
18' 30" 30 2 8 42 2 10 56 2 12 70 2 14 24' 26" 32 2 8 46 2 10 64 2 12 80 2 14 27' 24" 36 2 8 50 2 10 68 2 12 86 2 14 32' 20" 42 2 10 60 2 12 80 2 14 102 2 16 40' 16" 50 10 14 72 12 16 98 14 18 124 16 20 48' 13" 60 10 16 88 12 20 118 14 22 152 16 24 53' 12" 66 10 18 94 12 22 126 14 24 164 16 28 68' 10" 78 10 22 110 12 26 150 14 28 194 16 32 16' 24" and 12" 64 10 8 78 12 10 96 14 12 114 16 14
(for Grain Flow)
Grain Depth at
Bin Wall (ft.)
18' 30" 90 2 14 130 2 18 178 2 20 * 286 2 28 24' 26" 102 2 14 148 2 18 202 2 20 * 286 2 28
Spacing
(in.)
Spacing
(in.)
Full Double Single Full Double Single Full Double Single Full Double Single
Full Double Single Full Double Single Full Double Single Full Double Single
16' 5" 19' 8" 22' 11" 26' 3"
Bin Diameter - Number of Supports
29' 6" 36' 1" 42' 8" 49' 3"
27' 24" 108 2 14 160 2 18 218 2 20 **344 2 28 32' 20" 128 2 18 188 2 22 260 2 26 344 2 28 40' 16" 158 18 22 232 22 28 320 24 32 426 28 36 48' 13" 192 18 28 282 22 34 390 24 38 520 28 44 53' 12" 206 18 30 306 22 36 422 24 42 562 28 48 68' 10" 246 18 36 364 22 44 504 24 50 670 28 58 16' 24" and 12" 136 18 14 188 22 18 246 24 20 N/A N/A N/A
(for Grain Flow)
* Use 24" Spacing ** Use 20" Spacing
Page 37

14. Warranty

9101239_1_CR_rev7.DOC (revised July 2009)
GSI Group, LLC Limited Warranty
The GSI Group, LLC (“GSI”) warrants products which it manufactures to be free of defects in materials and workmanship under normal usage and conditions for a period of 12 months after sale to the original end-user or if a foreign sale, 14 months from arrival at port of discharge, whichever is earlier. The end-user’s sole remedy (and GSI’s only obligation) is to repair or replace, at GSI’s option and expense, products that in GSI’s judgment, contain a material defect in materials or workmanship. Expenses incurred by or on behalf of the end-user without prior written authorization from the GSI Warranty Group shall be the sole responsibility of the end-user.
Warranty Extensions:
The Limited Warranty period is extended for the following products:
Product Warranty Period
Performer Series Direct Drive Fan Motor 3 Years
AP Fans and Flooring
Cumberland Feeding/Watering Systems
Grain Systems Grain Bin Structural Design 5 Years Grain Systems
Farm Fans Zimmerman
All Fiberglass Housings Lifetime All Fiberglass Propellers Lifetime Feeder System Pan Assemblies 5 Years ** Feed Tubes (1-3/4" and 2.00") 10 Years * Centerless Augers 10 Years * Watering Nipples 10 Years *
Portable and Tower Dryers 2 Years Portable and Tower Dryer Frames and
Internal Infrastructure †
5 Years
* Warranty prorated from list price: 0 to 3 years - no cost to end-user 3 to 5 years - end-user pays 25% 5 to 7 years - end-user pays 50% 7 to 10 years - end-user pays 75% ** Warranty prorated from list price: 0 to 3 years - no cost to end-user 3 to 5 years - end-user pays 50%
† Motors, burner components
and moving parts not included. Portable dryer screens included. Tower dryer screens not included.
GSI further warrants that the portable and tower dryer frame and basket, excluding all auger and auger drive components, shall be free from defects in materials for a period of time beginning on the twelfth (12 and continuing until the sixtieth (60
th
) month from the date of purchase (extended warranty period). During the extended
th
) month from the date of purchase
warranty period, GSI will replace the frame or basket components that prove to be defective under normal conditions of use without charge, excluding the labor, transportation, and/or shipping costs incurred in the performance of this extended warranty.
Conditions and Limitations:
THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE LIMITED WARRANTY DESCRIPTION SET FORTH ABOVE. SPECIFICALLY, GSI MAKES NO FURTHER WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE IN CONNECTION WITH: (I) PRODUCT MANUFACTURED OR SOLD BY GSI OR (II) ANY ADVICE, INSTRUCTION, RECOMMENDATION OR SUGGESTION PROVIDED BY AN AGENT, REPRESENTA TIVE OR EMPLOYEE OF GSI REGARDING OR RELATED TO THE CONFIGURATION, INSTALLATION, LAYOUT, SUITABILITY FOR A PARTICULAR PURPOSE, OR DESIGN OF SUCH PRODUCTS.
GSI shall not be liable for any direct, indirect, incidental or consequential damages, including, without limitation, loss of anticipated profits or benefits. The sole and exclusive remedy is set forth in the Limited Warranty, which shall not exceed the amount paid for the product purchased. This warranty is not transferable and applies only to the original end-user. GSI shall have no obligation or responsibility for any representations or warranties made by or on behalf of any dealer, agent or distributor.
GSI assumes no responsibility for claims resulting from construction defects or unauthorized modifications to products which it manufactured. Modifications to products not specifically delineated in the manual accompanying the equipment at initial sale will void the Limited Warranty.
This Limited Warranty shall not extend to products or parts which have been damaged by negligent use, misuse, alteration, accident or which have been improperly/inadequately maintained. This Limited Warranty extends solely to products manufactured by GSI.
Prior to installation, the end-user has the responsibility to comply with federal, state and local codes which apply to the location and installation of products manufactured or sold by GSI.
PNEG-221 42' Cor-Lok and Cut-Lok Flooring 37
Page 38
This equipment shall be installed in accordance with
the current installation codes and applicable
regulations, which should be carefully followed in all
cases. Authorities having jurisdiction should be
consulted before installations are made.
Copyright © 2012 by GSI Group Printed in the USA
GSI Group
1004 E. Illinois St.
Assumption, IL 62510-0020
Phone: 1-217-226-4421
Fax: 1-217-226-4420
www.gsiag.com
CN-301476
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use