GSI PNEG-1342 User Manual

1200 Series Portable Dryer

Parts Manual

PNEG-1342

1200 Series Parts Manual

Table of Contents

1200 SERIES DRYER SPECIFICATIONS......................................................................4

MAIN STRUCTURE ASSEMBLY...................................................................................5

FRAME ASSEMBLY..............................................................................................................................................................5

FRAME, LOWER BASKET, AND METERING ROLLS......................................................................................................8

PLENUM (INSIDE) SCREENS AND METER ROLL UPPER SHIELD.............................................................................12

OUTER SCREENS AND PLENUM DIVIDER...................................................................................................................14

CLEAN OUT DOORS...........................................................................................................................................................16

FRONT AND REAR PLENUM END PANELS AND REAR ACCESS DOORS................................................................18

LADDER ASSEMBLIES......................................................................................................................................................20

BOTTOM AUGER...............................................................................................................................................................22

TOP AUGER WITH WET BIN............................................................................................................................................24

AUGER AND METER ROLL DRIVE TRAINS..............................................................26

BOTTOM AUGER DRIVE..........................................................................................................................................................26

TOP AUGER DRIVE...........................................................................................................................................................28

METER ROLL DRIVE........................................................................................................................................................30

FAN HEATERS.................................................................................................................32

FAN HOUSING ASSEMBLIES.................................................................................................................................................32

FAN MOTOR, MOTOR MOUNT, AND FAN BLADE................................................................................................................34

AIR MIXERS........................................................................................................................................................................35

FLAME PROBE, IGNITOR, AND BURNER ASSEMBLIES..............................................................................................36

LP PIPE TRAIN ASSEMBLIES...........................................................................................................................................38

NG PIPE TRAIN ASSEMBLIES..........................................................................................................................................44

FAN HEATER ORIFICES.....................................................................................................................................................48

LP SUPPLY LINE................................................................................................................................................................49

NG SUPPLY LINE...............................................................................................................................................................50

DRYER ELECTRICAL CONDUITS..................................................................................51

UPPER JUNCTION BOX, TOP AUGER MOTOR CONDUIT, AND OPERATOR LIGHT.......................................................51

RIGHT AND LEFT GRAIN, AND PLENUM HIGH LIMITS..............................................................................................52

LOWER JUNCTION BOXES, METER ROLL MOTOR CONDUIT, AND REAR DISCHARGE CONDUIT..........................54

AIR SWITCH ASSEMBLY...................................................................................................................................................56

CONTROL BOXES..........................................................................................................57

NETWORK CONTROL BOX..............................................................................................................................................57

FAN HEATER CONTROL BOX..........................................................................................................................................58

LOWER CONTROL BOX CONTROL PANEL..................................................................................................................60

LOWER CONTROL BOX CONTROL PANEL (INSIDE)...........................................................................................................61

LOWER CONTROL BOX BACK PANEL...........................................................................................................................62

UPPER CONTROL BOX.....................................................................................................................................................63

NOTES................................................................................................................................70

- 3 -

1200 Series Parts Manual

1200 Series Specifications

MODEL NUMBER

1218 1220 1222 122612161214

Grain Columns

Top Auger (Loading)

Bottom Auger

(Unloading)

Meter Roll Drive

Transport Length

Transport Width

Transport Heigth*

Transport Weight

(Less Transport Kit)

Installed Length

Installed Width

Installed Height

Fan/Heaters
Top
Bottom

* Shortest possible height shown in ().

14” x 14’ LONG 14” x 16’ LONG 14” x 18’ LONG

8”, 5HP

8” x 10” TUBE

SCR, 3/4HP SCR, 3/4HP SCR, 3/4HP SCR, 3/4HP SCR, 3/4HP SCR, 3/4HP

22’-10” 24’-10” 26’-10” 28’-10” 30’-10” 34’-10”

13’-5” (11’-7”) 13’-5” (11’-7”) 13’-5” (11’-7”) 13’-5” (11’-7”) 13’-5” (11’-7”) 13’-5” (11’-7”)

7200 lbs

(approx.)

20’-9” 20’-9” 20’-9” 20’-9” 20’-9” 20’-9”

14’-6” 14’-6” 14’-6” 14’-6” 14’-6” 14’-6”

10-12HP, 36”
10-12HP, 26”

14” x 20’ LONG 14” x 22’ LONG 14” x 26’ LONG

8”, 5HP 8”, 5HP 8”, 7.5HP 8”, 7.5HP 8”, 10HP

5HP

8’ 8’ 8’ 8’ 8’ 8’

8’ 8’ 8’ 8’ 8’ 8’

8” x 10” TUBE

5HP

7600 lbs

(approx.)

10-16HP, 36”
10-12HP, 26”

8” x 10” TUBE

5HP

7930 lbs

(approx.)

10-16HP, 36”
10-12HP, 26”

8” x 10” TUBE

7.5HP

9400 lbs

(approx.)

10-16HP, 40”
10-12HP, 28”

8” x 10” TUBE

7.5HP

10000 lbs
(approx.)

20HP, 42”

10-12HP, 28”

8” x 10” TUBE

12300 lbs
(approx.)

25HP, 42”

10-12HP, 28”

10HP

- 4 -

1200 Series Parts Manual

Frame

53

3

553

4a

3

5

4

Frame Assembly (view from fan/heater end with hitch weldment removed).

**NOTE: The parts pointed out on this page are listed on page 7.

- 5 -

Right side Left side

21a

1

The fan heater end of the dryer is considered by GSI as the front end of the dryer (the

foreground of this photograph is the front end. Right and left sides are labeled above).

1200 Series Parts Manual

Right front corner of frame.

3

1

1a

Frame

**NOTE: The right front corner
is shown in the photo. For left
front corner all parts are the
same except for the Hitch
Bracket (use 1a for the left side),
and the Frame Rail (use 4a for
the left side).

2

Left rear corner of frame.

3

4a

4

5

**NOTE: The left rear corner is
shown in the photo. For right
rear corner all parts are the same

2

4a

4

except for the Frame Rail (use 4
for the right side).

- 6 -

Center cross ties.

1200 Series Parts Manual

Frame

3

5

4a

4

2

ITEM

NUMBER

1 D01-0012 HITCH BRACKET RIGHT 1 1 1 1 1 1

1a D01-0011 HITCH BRACKET LEFT 1 1 1 1 1 1

2 D01-0008 FRONT & REAR FRAME TIE CHANNEL 4 4 4 4 6 6
3 D01-0007 CORNER LEG PORTABLE DRYER 6 6 6 6 8 8
4 D21-0011 FRAME RAIL, 14' RIGHT 1

4a D21-0010 FRAME RAIL, 14' LEFT 1

4 D01-0538 FRAME RAIL, 16' RIGHT 1

4a D01-0537 FRAME RAIL, 16' LEFT 1

4 D31-0044 FRAME RAIL, 18' RIGHT 1

4a D31-0043 FRAME RAIL, 18' LEFT 1

4 D61-0002 FRAME RAIL, 20' RIGHT 1

4a D61-0001 FRAME RAIL, 20' LEFT 1

4 D101-0002 FRAME RAIL, 22' RIGHT 1

4a D101-0001 FRAME RAIL, 22' LEFT 1

4 D71-0001 FRAME RAIL, 26' RIGHT 1

4a D71-0002 FRAME RAIL, 26' LEFT 1

5 D01-0005 SIDE LEG PORTABLE DRYER 10 12 14 16 16 20

PART

NUMBER

DESCRIPTION 1214 1216 1218 1220 1222 1226

- 7 -

1200 Series Parts Manual

Frame, Auger Trough, & Hopper Bulkheads

6

4

9

5

Dryer frame and lower basket assembly (view from the

front end of the dryer looking down the left side).

1

3

56 4

2

8 116

9 10

7

L.H. and R.H.

the plenum closure

distinguish between

door angles. This will

Note the hole pattern of

**NOTE: The parts pointed out on this page are listed on page 11.

- 8 -

1200 Series Parts Manual

Frame, Auger Trough, & Hopper Bulkheads

assembly.

shaft (part no. D31-0046) that

together with a meter roll splice

The meter roll sections are spliced

Wooden meter roll support bearing.

passes through the support bearing

181716

9

21

6

4

19

20

Discharge bearing plate.

3

6

Center hanger bearing support

and cross channel seal plate.

9

12

5

11a

12

3

9 6

4

12 13 12 14 15 3

6

**NOTE: The parts pointed out on this page are listed on page 11.

- 9 -

Dryer frame and lower basket assembly (view from the

rear end of the dryer looking up the right side).

Meter Rolls and Their Placement in the Dryer

Metering Rolls and their placement in the dryer.

NOTE: Item 22 at the rear of
dryer is a front section meter

roll that is used as a rear section

on 16 and 20 foot dryers only.

1200 Series Parts Manual

22

24

Meter Roll Bearing

See pg. 11

Items 16, 17, 18

23

23

13

19

23

Meter Roll Bearing

See pg. 11

Items 16, 17, 18

23

Meter Roll Bearing

See pg. 11

Items 16, 17, 18

19

22

22

This end is the front (fan/heater) end of the dryer.

- 10 -

1200 Series Parts Manual

Meter Rolls and Their Placement in the Dryer

ITEM

NUMBER

1 D01-1136Y PLENUM CLOSURE DOOR ANGLE, RH 6 7 8 9 10 12
2 D01-1136X PLENUM CLOSURE DOOR ANGLE, LH 7 8 9 10 11 13
3 D01-0109 HOPPER BULKHEAD 12 14 16 18 20 24
4 D01-0004 GUSSET PLATE 16 18 20 22 24 28
5 D01-0005 SIDE LEG 10 12 14 16 16 20
6 D01-0007CORNER LEG 666688
7 D01-0011 HITCH BRACKET, LH 1 11111
8 D01-0012 HITCH BRACKET, RH 1 11111

9 D01-0008FRONT & REAR FRAME TIE CHANNEL 444466
10D01-1374BOTTOM AUGER BEARING PLATE 111111
11 D21-0011 FRAME RAIL, 14' RIGHT 1
11 D01-0538 FRAME RAIL, 16' RIGHT 1
11 D31-0044 FRAME RAIL, 18' RIGHT 1
11 D61-0002 FRAME RAIL, 20' RIGHT 1
11 D101-0002 FRAME RAIL, 22' RIGHT 1
11 D71-0001 FRAME RAIL, 26' RIGHT 1

11A D21-0010 FRAME RAIL, 14' LEFT 1
11A D01-0537 FRAME RAIL, 16' LEFT 1
11A D31-0043 FRAME RAIL, 18' LEFT 1
11A D61-0001 FRAME RAIL, 20' LEFT 1
11A D101-0001 FRAME RAIL, 22' LEFT 1
11A D71-0002 FRAME RAIL, 26' LEFT 1

12 D01-0048 TROUGH PANEL 14 16 18 20 22 26
13D01-1512PLATE, CROSS CHANNEL SEAL W/TABS 111122
14 D01-1291 HANGER BEARING "C" CHANNEL 1 11122
15 D01-1290 HANGER BEARING "J" PLATE 2 22244
16 D02-0028 CLEVIS PIN 5/16" x 1 3/4" 32 32 40 40 48 56
17 D31-0148 METER ROLL WASHER 16 16 20 20 24 28
18 D02-0061 METER ROLL SUPPORT BEARING 6 6 8 8 10 12
19 D01-0177 SUPPORT STRAP 7 8 9 10 11 13
20 D01-1511 PLATE, END CHANNEL SEAL W/TAB 2 22222
21 D31-0120 DISCHARGE PLATE 1 11111
22D31-0031METER ROLL, FRONT 242422
23D31-0030METER ROLL, INTERMEDIATE 4466810
24 D31-0029 METER ROLL, REAR 2 2 2 2

PART

NUMBER

DESCRIPTION 1214 1216 1218 1220 1222 1226

The part number list above covers all parts pointed out on pages 8, 9, and 10.

- 11 -

1200 Series Parts Manual

Inside (Plenum) Screens, Plenum Closure Doors

Plenum screens and bulkheads (view from front end).

3

4

3

5

12

5

6

16

7

8

10

11

13

14

18

19

12

9

10

7

15

This photograph was taken before the front

plenum end panel and outer screens where

installed in order to get a good view of the inside

20

20a

screens and bulkheads.

22

21

Plenum closure door. There are two different plenum closure doors. The door
shown in the photogragh is the rear plenum closure door and is the rear most
plenum closure door, item no. 20 (just inside the rear access door), all others
are item no. 20a. NOTE: Item 22 is the plenum closure door rear frame angle.

- 12 -

1200 Series Parts Manual

Meter Roll Upper Shield Assembly

Close up of of meter roll upper shield assembly.

16

17

18

19

19

18

17

ITEM

NUMBER

1 D31-0055 COLUMN BULK HEAD 12 14 16 18 20 24

2 D01-0101 GARNER BULKHEAD 12 14 16 18 20 24

3 D31-0307 COLUMN END PANEL 4 4 4 4 4 4

4 D01-0126 SCREEN,PLENUM TOP,GA,094 14 16 18 20 22 26

5 D31-0012 SCREEN,PLENUM WALL,GA,094 14 16 18 20 22 26

6 D01-1225 SCREEN,PLENUM BOTTOM,GA,094 14 16 18 20 22 26

7 D01-0004 GUSSET PLATE 16 18 20 22 24 28

8 D21-0011 FRAME RAIL, 14' RIGHT 1

8 D01-0538 FRAME RAIL, 16' RIGHT 1

8 D31-0044 FRAME RAIL, 18' RIGHT 1

8 D61-0002 FRAME RAIL, 20' RIGHT 1

8 D101-0002 FRAME RAIL, 22' RIGHT 1

8 D71-0001 FRAME RAIL, 26' RIGHT 1

9 D21-0010 FRAME RAIL, 14' LEFT 1

9 D01-0537 FRAME RAIL, 16' LEFT 1

9 D31-0043 FRAME RAIL, 18' LEFT 1

9 D61-0001 FRAME RAIL, 20' LEFT 1

9 D101-0001 FRAME RAIL, 22' LEFT 1

9 D71-0002 FRAME RAIL, 26' LEFT 1
10 D01-0007 CORNER LEG PORTABLE DRYER 6 6 6 6 8 8
11 D01-0012 HITCH BRACKET RIGHT 1 1 1 1 1 1
12 D01-0011 HITCH BRACKET LEFT 1 1 1 1 1 1
13 D01-0008 FRONT & REAR FRAME TIE CHANNEL 4 4 4 4 6 6
14 D01-1374 BOTTOM AUGER BEARING PLATE 1 1 1 1 1 1
15 D01-0005 SIDE LEG PORTABLE DRYER 10 12 14 16 16 20
16 D01-0109 HOPPER BULKHEAD 12 14 16 18 20 24
17 D01-0050P CONNECTOR SHEET, PERFORATED 14 16 18 20 22 26

*18&19 D01-1180 METER ROLL UPPER SHIELD ASSY. 14 16 18 20 22 26

18 D01-0431 METER ROLL STRIKE OFF PLATE
19 D01-1226 METER ROLL SHIELD 1995 STYLE

20 D01-1214 PLENUM CLOSURE DOOR, REAR 1 1 1 1 1 1

20a D01-1134 PLENUM CLOSURE DOOR 6 7 8 9 10 12

21 DC-974 DANGER FOOT IN AUGER DECAL 2 2 2 2 2 2
22 D01-1217 PLENUM CLOSURE DOOR REAR FRAME ANGLE 1 1 1 1 1 1

PART

NUMBER

DESCRIPTION 1214 1216 1218 1220 1222 1226

1 PER ASSEMBLY
1 PER ASSEMBLY

*ITEM NUMBERS 18 AND 19 TOGETHER MAKE UP THE METER ROLL UPPER SHIELD ASSEMBLY

- 13 -

1200 Series Parts Manual

Outer Screens, & Meter Roll Access Door

Outer screens (view from front end).

2

*

3

*

3a

4

*

3

2

3

3a

4

5

1

*Note: Item 3 is pointing to the

top edge angle gusset. There are

two types of gusset on the dryer.

The photo above will help

distinguish the difference

between the two. The arrows are

pointing to a tab on the gusset

13

14

that makes them different (tabs

are “bent” up in photo). Item 3a

is used in two places only; 1.)

front right of dryer 2.) rear left

of dryer, all others are item 3.

11

6

17

18

16

12

13

14

15

Meter roll access door.

6

19

20

22

21

23

24

- 14 -

1200 Series Parts Manual

Plenum Divider

Plenum divider.

7 8

Plenum divider clean-out door.

9

10

9

The photo above and on page 16 was taken before plenum end

panels where installed.

ITEM

NUMBER

1 D31-0307 COLUMN END PANEL 4 4 4 4 4 4
2 D01-0113 WALK RAIL MOUNTING BRACKET 18 20 22 24 28 32

3 D01-0152 TOP EDGE ANGLE GUSSET - LH 14 16 18 20 22 26

3a D01-0153 TOP EDGE ANGLE GUSSET - RH 2 2 2 2 2 2

4 D01-0127 SCREEN, ROOF SHEET 14 16 18 20 22 26
5 D31-0013 SCREEN, OUTSIDE WALL SHEET 14 16 18 20 22 26
6 D01-0128 SCREEN, HOPPER SHEET 14 16 18 20 22 26
7 D31-0032 PLENUM DIVIDER: MF: BOTTOM 12 14 16 18 20 24
8 D31-0033 PLENUM DIVIDER: MF: BOTTOM END 2 2 2 2 2 2

9 D31-0260 CLEAN-OUT DOOR GUIDE 4 4 4 4 4 4
10 D31-0259 PLENUM DIVIDER CLEAN-OUT DOOR 2 2 2 2 2 2
11 D21-0011 FRAME RAIL, 14' RIGHT 1
11 D01-0538 FRAME RAIL, 16' RIGHT 1
11 D31-0044 FRAME RAIL, 18' RIGHT 1
11 D61-0002 FRAME RAIL, 20' RIGHT 1
11 D101-0002 FRAME RAIL, 22' RIGHT 1
11 D71-0001 FRAME RAIL, 26' RIGHT 1
12 D01-0005 SIDE LEG PORTABLE DRYER 10 12 14 16 16 20
13 D01-0004 GUSSET PLATE 16 18 20 22 24 28
14 D01-0007 CORNER LEG PORTABLE DRYER 6 6 6 6 8 8
15 D01-0012 HITCH BRACKET RIGHT 1 1 1 1 1 1
16 D01-0011 HITCH BRACKET LEFT 1 1 1 1 1 1
17 D01-0008 FRONT & REAR FRAME TIE CHANNEL 4 4 4 4 6 6
18 D01-1374 BOTTOM AUGER BEARING PLATE 1 1 1 1 1 1
19 D01-0050P CONNECTOR SHEET, PERFORATED 14 16 18 20 22 26
20 D01-0045P ACCESS DOOR, PERFORATED 14 16 18 20 22 26
21 D01-0039 DOOR LATCH 28 32 36 40 44 52
22 S-6552 PIN, HAIR CLIP 3/32" 28 32 36 40 44 52
23 DC-1229 DECAL, WARNING METER ROLL ROT. 14 16 18 20 22 26
24 D01-0048 TROUGH PANEL WELDMENT 14 16 18 20 22 26

PART

NUMBER

DESCRIPTION 1214 1216 1218 1220 1222 1226

- 15 -

1200 Series Parts Manual

Clean Out Doors

Front and rear handle mechanisms (rear shown in photo).

1

3

2

4

5

13

*Note: Items 9, 10, & 11 together create the
clean out door assembly. There are three
different clean out door assemblies that are used
on GSI Network dryers:

1.) 3 column clean out door assy. (D51-0077).
Item 8a on the part no. listing (pg 17).

2.) 4 column clean out door assy. (D11-0032).
Item 8b on the part no. listing (pg 17).

3.) 5 column clean out door assy. (D01-0349).
Item 8c on the part no. listing (pg 17).

A 5 column clean out door assy (D01-0349) is
shown in the photograph below.

11

Clean out door handle mechanism.

4

3a

3

2

Clean out door hinge.

5

9

6

7

11

10

9

10

12

11

13

11

- 16 -

1200 Series Parts Manual

Clean Out Doors

Center handle mechanisms (this handle mechanism stradles the center cross channels).

14

3a

1a

14

3a 11

4

2

5

14

ITEM

NUMBER PART NUMBER

1 D01-0264 PIVOT ROD 25.188" 2 2 2 2 2 2
1a D31-0162 PIVOT ROD 49.625" 1 1 1 1 2 2

2 D01-0296 LINKAGE BAR WELDMENT 4 4 4 4 6 6

3 D01-0261 LINKAGE BAR, 37" LONG 2 2 2 2 2 2
3a D01-0293 LINKAGE BAR, 30" LONG 2 2 2 2 4 4

4 D01-0294 CLEAN OUT DOOR HANDLE 4 4 4 4 6 6

5 S-4378 PLASTIC GRIP 4 4 4 4 6 6

6 S-248 WASHER, FLAT 3/8 USS ZN 8 8 8 8 12 12

7 S-7241 COTTER PIN, 1/8 x 1 1/4 8 8 8 8 12 12

8a D51-0077 CLEAN OUT DOOR ASSY, 3 COLUMN 1 1

9 D21-0005 CLEAN OUT DOOR, 67"
10 D21-0012 SUPPORT CHANNEL, CLEAN OUT DOOR
11 D01-0308 CLEAN OUT DOOR HINGE

8b D11-0032 CLEAN OUT DOOR ASSY, 4 COLUMN 1 2 1 2 2

9 D31-0021 CLEAN OUT DOOR, 91"
10 D31-0130 SUPPORT CHANNEL, CLEAN OUT DOOR
11 D01-0308 CLEAN OUT DOOR HINGE

8c D01-0349 CLEAN OUT DOOR ASSY, 5 COLUMN 1 2 1

9 D01-0180 CLEAN OUT DOOR, 115"
10 D01-0307 SUPPORT CHANNEL, CLEAN OUT DOOR
11 D01-0308 CLEAN OUT DOOR HINGE

12 D01-0175 HINGE BRACKET 4 5 5 6 6 7
13 D01-0181 CLEAN OUT EXTENSION, 119.75" 2 4 2
13 D31-0023 CLEAN OUT EXTENSION, 90.75" 2 4 2 4 4
13 D21-0006 CLEAN OUT EXTENSION, 66.75" 2 2
14 D01-0299 PIVOT ROD BRACKET 3 3 3 3 6 6

DESCRIPTION 1214 1216 1218 1220 1222 1226

1 PER ASSEMBLY
1 PER ASSEMBLY

2 PER ASSEMBLY

1 PER ASSEMBLY
1 PER ASSEMBLY

2 PER ASSEMBLY

1 PER ASSEMBLY
1 PER ASSEMBLY

3 PER ASSEMBLY

- 17 -

1200 Series Parts Manual

Front & Rear Plenum End Panels, & Upper & Lower Rear Access Doors

Rear end panels. Front end panels & support arms.

2

1

3

1

5

4

1

3

3

27

Aspirator end cap.

Lower rear access door.

10

25

26

12

6

9

7

6

8

1

Upper rear access door.

15

16

16

11

12 13 14

10

- 18 -

11

14

16

16 17

1200 Series Parts Manual

Front & Rear Plenum End Panels, & Upper & Lower Rear Access Doors

Lower rear access door (inside). Upper rear access door (inside).

22

15

23

24

24

23

17 21

18

19

20

13 21

22

ITEM

NUMBER PART NUMBER

1 D31-0307 COLUMN END PANELS 444444
2 D01-1801-Y REAR END PANEL 40/60 111111
3 D01-0044 TOP ANGLE BRKT FRONT & REAR 333333
4 D81-0019 FRONT END PANEL 36 & 26" 1 1 1
4 D71-0021 FRONT END PANEL 40" & 28 1
4 D101-0020 FRONT END PANEL 42 & 28" 1 1
5 D51-0022 SUPPORT, CONTROL PANEL 555555
6 D01-0778 DIAGONAL SUPPORT CHANNEL, 5' 222222
7 D01-0029 HITCH WELDMENT 111111
8 D31-0129 DIAGONAL SUPPORT ANGLE 222222

9 D31-0293 LADDER ASSEMBLY (SEE PAGE 23) 222222
10 D01-0395 SQUARE DOOR SIDE BRKT 222222
11 D03-0512 DOOR HANDLE LOCKING 222222
12 D01-0396 SQUARE DOOR TOP/BOTTOM BRKT 222222
13 D01-0394 SQUARE REAR ACCESS DOOR 111111
14 DC-973 DECAL, DANGER FIRE HAZARD 222222
15 D01-1783-Y ASSIST HANDLE, 29" SQ. DOOR 222222
16 D01-1782-BLK FRAME ANGLE, 29" SQ. DOOR 444444
17 D01-1781-Y DOOR, 29" SQUARE 111111
18 D31-0297 REAR DOOR HINGE, TOP 111111
19 D31-0161 HINGE BRACKET 111111
20 D31-0296 REAR DOOR HINGE, BOTTOM 111111
21 D01-1792 LATCH BAR 222222
22 D01-0397 LATCH BRACKET 222222
23 401-4669-8 REAR ACC. DOOR HINGE, DOOR HALF 222222
24 401-4630-0 HINGE BRACKET 222222
25 D01-1510 ASPIRATOR END CAP 111111
26 DC-974 DECAL DANGER FOOT IN AUGER 111111
27 D01-0481-MS REAR DISCHARGE BOX ASSEMBLY 111111

DESCRIPTION 1214 1216 1218 1220 1222 1226

- 19 -

Fan/Heater ladder assembly.

1200 Series Parts Manual

Ladder Assemblies

1

4

2

5

6

3

ITEM

NUMBER

1 D01-0111 LADDER RAIL 2 2 2 2 2 2
2 D01-1576 LADDER MNTNG PLATE 2 2 2 2 2 2
3 D01-0112 LADDER RUNG 8 8 8 8 8 8
4 CD-0543-Y VENTURI: 36" 1 1 1
4 CD-0545-Y VENTURI: 40" 1
4 CD-0546-Y VENTURI: 42" 1 1
5 F-7062-Y VENTURI: 26" 1 1 1
5 F-7060-Y VENTURI: 28" 1
6 D51-0021 STIFFENER, FRONT FAN SUPPORT 2 2 2 2 2 2

PART

NUMBER

DESCRIPTION 1214 1216 1218 1220 1222 1226

- 20 -

1200 Series Parts Manual

Ladder Assemblies

Front and rear ladder assembly.

1

5

2

3

1

6

7

3

1

2

1

3

4

ITEM

NUMBER

1-4 D31-0293

1 D01-1012 LADDER BRACKET 4 4 4 4 4 4
2 D31-0020 LADDER RAIL 2 2 2 2 2 2
3 D01-0112 LADDER RUNG 10 10 10 10 10 10
4 D01-0114 LADDER LOWER BRACKET 1 1 1 1 1 1
5 CD-0544 GRILL GUARD: 36" 1 1 1
5 CD-0547 GRILL GUARD: 40&42" 1 1 1
6 CD-0575 GRILL GUARD: CD-26 1 1 1
6 CD-0576 GRILL GUARD: CD-28 1 1 1
7 D81-0020 FRONT FAN SUPPORT 36 & 26" 1 1 1
7 D71-0022 FRONT FAN SUPPORT 40 & 28 1
7 D101-0021 FRONT FAN SUPPORT 42&28 1 1

PART

NUMBER

DESCRIPTION 1214 1216 1218 1220 1222 1226

LADDER ASSEMBLY, TALL PROFILE 2 2 2 2 2 2

- 21 -

1200 Series Parts Manual

Bottom Auger (view from center of dryer to
the forward end).

Bottom Auger

Bottom Auger (view from center of dryer to
the rear end).

1

2

2

3

2

4

Bottom Auger center bearing and support. Bottom Auger rear bearing.

- 22 -

8 75 7 6