Grasslin Talento Smart User Manual
DE
Betriebsanleitung 2
EN
Operating instructions 36
FR
Manuel ‘utilisation 48
IT
Manuale dell‘utente 72
ES
Manual de instrucciones 94
PT
Manual de instruções 118
NL
Handleiding 130
CS
Provozní návod 154
SV
Bruksanvisning 176
NO
Bruksanvisning 198
DA
Driftsvejledning 220
FI
Käyttö- ja huolto-ohje 244
PL
Instrukcja eksploatacji 268
HU
Kezelési útmutató 290
6
09:00
talento smart
Table of Contents
Safety Information .................37
Information about the device .........38
Description of the device ................................38
Intended Use .........................................38
Technical Data ........................................38
Declaration of Conformity ...............................38
FCC certication ......................................39
Assembly and Installation ...........40
Installation on a DIN-rail ................................40
Circuit diagram .......................................40
Operation and Setting .............. 41
Display and Function Keys ...............................41
Overview of menu structure ..............................42
Initial commissioning ...................................43
Programming .........................................44
Conguration .........................................57
Set date and time .....................................64
Switch summer / winter time .............................65
Language setting ......................................66
Automatic / manual operation ............................67
EN
Maintenance and Service ...........69
Distribution partners ...................................69
Software update ......................................69
Disposal and Recycling .............70
36
Safety Information
Risk of death due to electrical shock!
Incorrect assembly and installation of the device can result in life-threatening electrical
WARNING
Please note:
• National regulations and safety regulations
• Guarantee is invalidated if you tamper with the device or modify it
• Minimum diameter of the exible lines for the connecting terminals: 1 mm
• Maximum diameter of the exible lines for the connecting terminals: 2,5 mm
Read this manual and pay attention to its contents to ensure that the device works perfectly and that you
can work safely with it.
voltages.
This product should be installed by an electric specialist according to current installation
standards.
EN
2
2
37
Information about the device
Description of the device
Digital DIN-rail time switch
• Date-independent programming
• Date-dependent programming
• Pulse, cycle and random programming*
• Sunrise/sunset related programming
• Program creation by means of PC and mobile devices
• Bluetoothlow energy interface
Intended Use
• The device is suitable for the following applications:
− Lighting in private and commercial areas
− Advertising signs
− Street lighting
− Shop lighting
− Devices, motors and pumps control
− Roller blinds and sun blinds control
− Simulation of home presence
• Only suitable for use on dry premises
• Do not use close to devices with inductive discharge (motors, transformers, etc.)
• Install only on DIN-rails
EN
Technical Data
You can nd the technical data for the devices that are described in this manual at:
www.graesslin.de/technical-data
Declaration of Conformity
You can nd the declaration of conformity for the devices that are described in this manual at:
www.graesslin.de/doc
* These functions depend on variant.
38
FCC certication
FCC ID: 2AHH7-DG
This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions;
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Labelling Requirments
The Original Equipment Manufacturer (OEM) must ensure that FCC labelling requirements are met.
This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate
Grässlin GmbH FCC identier for this product as well as the FCC Notice above.
The FCC identiers is: 2AHH7-DG
This FCC identier are valid for Talento Smart x15 and Talento Smart x25, for details. In any case the
end product must be labelled exterior with:
“Contains FCC: 2AHH7-DG”
EN
39
Assembly and Installation
Risk of death due to electrical shock!
Incorrect assembly and installation of the device can result in life-threatening electrical
WARNING
Installation on a DIN-rail
1. Place the device onto the DIN-rail from the top at a slight angle.
2. Press it backwards until it clicks into place.
voltages.
This product should be installed by an electric specialist according to current installation standards.
EN
Circuit diagram
CH1 = Channel 1
CH2 = Channel 2
CH1
M
~
LN
123
1 channel variant 2 channel variant
Install the device according to the circuit diagram (with one or two channels depending on the
variant).
M
~
LN
CH1
1235 6
CH2
7
40
G
H
I
Operation and Setting
Display and Function Keys
1 6 12 18 24
C
B
A
CH 1
OvrFix
13.03.2016
09:00
OVRFIX
1 2
51
Menu
D
E
F
Display:
A Function displays of the buttons on the left
B Date and time or menu navigation
C Programmed switching times
D Display of summertime/wintertime
E Bluetooth display
F Function displays of the buttons on the
right
Buttons:
G Buttons on right
H Reset button
I Buttons on left
EN
Function displays of the two buttons on the right (G):
Menu Leave auto mode and enter programming Mode
ESC Press briey = Goes back one step
Press for a long time (about 2sec) = Goes back to auto mode
OK Make the selection and apply it
< Undo the last input, e.g. when entering the time
Function displays of the two buttons on the left (I):
1
Channel status for channel 1
2
Channel status for channel 2
˄ Page upwards in the menu
˅ Page downwards in the menu
- Press briey = The displayed value (hour, minute, etc.) is decremented by 1/
Press for a long time (about 2sec) = fast scrolling
+ Press briey = The displayed value (hour, minute, etc.) is incremented by 1/
Press for a long time (about 2sec) = fast scrolling
41
Overview of menu structure
Menu
EN
Program
New
View Edit/
Delete All
S /Wi Timeu
Config
Light
Astro*
Hour-Counter
PIN
Mod *e
Bluetooth
Language
Dat /e Time
24 Hours
AM/PM
Auto
Calibr 1
Calibr 2
No
* These functions depend on variant.
English
Deutsch
Français
Español
Portuges
Italiano
...
42
Initial commissioning
When delivered, the device is in automatic mode with default settings for time, date and language
(English).
When the menu buttons are rst operated, a wizard walks you through the basic settings that you can
check during initial commissioning and adjust if necessary.
Menu
Language
*English
Astro*
The following settings are queried during initial commissioning:
• Language; see „Language setting“ on page 66
• Location information (country, coordinates) for astro calculation; see "Location information"
on page 58
OK
EN
OK
OK
* These functions depend on variant.
43
Programming
Switch-off commands have priority over switch-on commands.
INFORMATION FOR PROGRAM CREATION
The device is programmed in the following steps:
• Setting data or date range
In this menu, you can specify on which day and at what time (date from ... to) the device is turned
on or off.
• Setting the function and switching time
Under this menu item, you specify which switching command is performed at which time
(ON, OFF, pulse*, cycle*, random*). This can be specied per channel for different date ranges or
date-independent.
EN
* These functions depend on variant.
44
CREATE NEW SWITCHING PROGRAM
Menu
Menu
Program
New
With Date?
No
OK
OK
OK
Select FNC
...
Programming without date
Program
New
With Date?
Yes
OK
OK
OK
OK
Date from
2015.10.01
... Dya
Date to
2015.10.02
...Dya
OK
OK
AddeDat?
No
OK
Select FNC
...
OK
OK
Programming with date
To create a new switching program, press the key
1. Select
2. Select
Program and
New and
conrm with
conrm with
OK.
OK.
Menu
:
The number of available program memory spaces is displayed briey (PXXX). The number of available
switching channel memory spaces (Dxxx) then appears.
The available memory spaces depend on the variant of the device.
EN
3. In step
–
With date?
No
and
specify with
OK
, the device should be programmed without date range.
The switching commands are valid date-independent.
Proceed with action step to step 4.
– Specify
Yes
and
OK
so that the device will be programmed with a date range.
The switching commands are valid for the dates and periods which are dened in the programming, also see page 46.
You can dene multiple date ranges. If the time periods have been determined, end the query
No
after the last date range with
If you have congured the location information (astro function) in the device, you can choose when
.
changing, whether the device should be switched directly to sunrise and sunset via the day limit.
The astro function is not available in all versions of the device, see also „Location information (Ast
ro)“ on page 58.
-
45
4. In step
ON
−
SELECT FCT
(FCT = Function), specify the type of switching command:
Select the times at which a channel should be switched on A.
OFF
−
Select the times at which a channel should be switched off B.
Pulse
−
Select the settings for pulse programming C.
Cycle
−
Select the settings for cycle programming D.
Random ON
−
Select the settings for random program ON E.
Random OFF
−
Select the settings for random program OFF F.
OK
5. Select the desired function and confirm with
.
The number of available switching command memory spaces appears (CXXX).
The available memory spaces depend on the variant of the device.
EN
USING WILDCARDS
You can use wildcards when entering the date. This allows you to program recurring switching times
that are always to be carried out, for example, always the rst of the month. Instead of annual or
monthly numbers, choose the wildcards **** for the year and ** for the month.
Below you see how date entries appear and how you can use wildcards:
2016.03.13 - 2016.03.13
•
The switching command is executed only on 13 March 2016.
2016.03.13 - 2016.03.20
•
The switching command is executed between 13 March 2016 and 20 March 2016.
2016.**.13 - 2016.**.13
•
The switching command is executed the 13th of every month in 2016.
****.**.01 - ****.**.01
•
The switching command is always executed annually on the rst day of a month.
Die Wildcards für die Jahre nden Sie bei der Datumseingabe indem Sie vor die aktuelle Jahreszahl
blättern. Die Wildcards für die Monate nden Sie zwischen Dezember und Januar.
46
Loading...