Grasslin talento 371, talento 372 User Manual

1. Contents

2

GB

1. Contents Page

2. Assembly, putting into operation, connection 3

3. Control elements 4

4. Display 4

5. Factory setting 5

6. Changing settings 6

6.1 Time and day of the week 6

6.2 Calendar month and day 7

6.2.1 AU = Automatic changeover 7

6.2.2 cHA = Weekday-related time change 8 - 9

6.2.3 no = no changeover 10

7. Standard switching commands 11

8. Weekday block formation 12 - 13

9. Read – change – delete – reset 14 - 15

10. Hand switch 16

11. Technical data 17

2. Assembly, putting into operation, connection

3

2.1 Assembly

Fit the time switch

• on a DIN rail

• optional wall surface-mounting
Surface-mounting set for 2 and
3 module spacings
Article No. 03.53.0083.2

2.2 Putting into operation

The time and date are set at the factory.
The time switch is in Energy-saving mode.
Only the colon flashes.
Press any key:

• The time switch is actived

•

It displays the time (day of the week)

2.3 Connection

See information on the unit!
Press any key to activate the time switch

• the time and date is displayed

Note:

If no key is pressed the time switch is
automatically activated after approx
1 - 2 minutes.

Safety instruction:

•

When operating the clock safety low
voltage, only safety low voltage may
be connected.

•

When operating the clock with function
low voltage, mains voltage (230 ~) or
function low voltage may be connected.
The connection of safety low voltage is
not admissible in this case.

AC
DC

+

–

AC
DC

+

–

3. Control elements

4

GB

4. Display

Start program input

Set time,
end program input

Select day(s)
of the week

Delete switching time

Set hours, day, year

Hand switch

Enter pulse/

cycle
Reset

Set minutes, month, year

Summer time/winter time switchover

Date

Summer time
display

AM/PM
display

DCF 77
reception

Channel 1
Channel 2

Switching state

Automatic mode

1234567 =

days of the week

1 = Monday

Hours - current time
Calendar day

- current date

- start/end
summer time

Minutes - current time
Month - current date

- start/end
summer time

Year - day/month

Pulse/cycle

Continuous operation

Manual operation

5

5. Factory setting

The selections correspond to Central European Time. The time
switch offers 3 Operating modes. The date and time, and also
the Operating mode AU are set.

Operating modes:

• AU Automatic summer time controller switchover
see 6.2.1

The switchover occurs on the dates defined by
the legislator.

• cHA Weekday-related summer time controller

switchover, see 6.2.2

You enter the start and end dates of summer time
which applies to your location/country.
e. g. The first Sunday in April of the current year

(start of summer time)
The last Sunday in October of the year

(end of summer time)
In the following years, changeover always occurs
on the right day of the week in the correct calendar
week.

• no No changeover, see 6.2.3

AM/PM switch-over
Switch clock is in current operating mode

1. Press h and keep pressed

2. – Press Res once
– all segments are displayed
–

after approx. 1 second the following appears:
AM, 12.00 and 3 (Wednesday)

Operating mode AU is active = works setting

3. Release h

4.

Select operating mode as required, see 6.2.1 or 6.2.2 or 6.2.3

5. Set the current time of day and weekday, see 6.1

GB

6

6. Changing settings

Press the key once

Set the time:

With the h key – hours
With the m key – minutes

Note for weekly time switch:

If the Operating mode

no = no change

- see 6.2.3

was selected, the day of the
week must now be set.
With the Day

1 - Monday

key select: 2 - Tuesday

3-

Wednesday
:
7 - Sunday

Press the key once.
The input is ended.

6.1 Time and day of the week

Note:

You can exit/conclude any adjustments, changes you make
at any time with the key .