Groen TDHC-20 User Manual

TABLE TOP KETTLES

PROJECT NAME:

LOCATION:

ITEM NO:

CRANK TILT GAS MODEL TDHC

Kettle shall be a Groen Model TDHC (specify 20, 24, 40 or 48-quart) stainless steel, self-contained crank tilt,
steam jacketed unit operating from a gas heated steam source contained within unit.

AVAILABLE MODELS:

TDHC-20 (20 QUART)
TDHC-24 (24 QUART)
TDHC-40 (40 QUART)
TDHC-48 (48 QUART)

CONSTRUCTION: Kettle shall be of 304 stainless

steel, one-piece welded construction. All exposed
surfaces shall be stainless steel. All controls shall
be contained in a gasketed enclosure. Unit shall be
furnished with a heavy reinforced rim with a welded in
butterfly shaped pouring lip for durability and pouring
control. The crank tilt handle shall be on the right side
support and provide easy and precise one hand tilting of
kettle body. Faucet bracket is standard and mounted on
rear of electrical control box.

FINISH: Interior of kettle shall be polished to a 180

emery grit finish. Exterior of kettle shall be finished to
a bright high buff finish, ensuring maximum ease in
cleaning and maintaining brilliant appearance.

ASME CODE & CSA DESIGN CERTIFIED:

Unit shall be ASME shop inspected, stamped and
registered with the National Board for operation up to
a maximum working pressure of 50 PSI. Unit shall be
design certified by the CSA.

SANITATION: Unit shall be designed and

constructed to meet NSF and known health department
and sanitation codes, and be NSF listed.

SELF-CONTAINED STEAM SOURCE: Kettle

shall have a gas-heated (natural and propane gases
C.S.A. certified; consult factory for butane or butane/
propane mixture), self-contained steam source to

provide kettle temperatures of 150° to approximately
295°F. Unit shall be factory charged with water
and rust inhibitors to ensure long life and minimum
maintenance.

CONROLS: Controls shall include a thermostat,

pressure gauge, gas regulator valve, heating indicator
lamp, on/off switch, front mounted water sight glass
and electronic spark ignition.

SAFETY FEATURES: Kettle shall have safety

tilt cut-off (cuts off heat when tilted to 12º and
above), pressure relief valve, high limit pressure
switch, and low water cut-off. Gas supply shuts off
automatically when unit is tilted. 24V control system.

PERFORMANCE/FEATURES: Features

Patented fin tube burner assembly delivers efficient
combustion. The 20/24 quart unit shall have 31,000
BTU/hr firing rate and the 40/48 quart unit shall have
a 52,000 BTU/hr firing rate. Electronic spark ignition
is standard. Unit shall be thermostatically controlled
to automatically shut off when desired temperature is
reached and turn on when product temperature drops
below desired setting. Crank tilt design shall make it
possible for one person to easily tilt kettle, even when
kettle is filled to capacity. Pouring height allows filling
of 4” high pans on the table top.

INSTALLATION: Specify natural, propane,

butane or specific propane/butane mixture. Unit
requires 1/2” NPT gas line connection and 115 volt
electric supply for spark ignition. Remote steam
source is not required.

ORIGIN OF MANUFACTURE: Designed and

manufactured in the United States.

QTY:

MODEL NO:

AIA NO:

SIS NO:

stainless steel 2/3 steam jacketed
kettle, table top, crank tilt, self­contained, gas heated 20,24,40
and 48-quart capacity.

OPTIONS/ACCESSORIES:

Etch marks, gallons
Etch marks, liters
Correctional package
316 s/s liner
Single pantry faucet
Double pantry faucet
Single pantry pre-rinse
Double pantry pre-rinse
Basket insert
Nylon basket liner
Liner retaining ring
Lift off cover
Cover holder
Cover strainer
Stand
Drain cart
Cart plumbing kit

Table Top Kettles

143945 RevD

Revised 04/12

P/N 146528 REV E

TDHC

P/N 137718 REV C

1055 Mendell Davis Drive, Jackson, MS 39272, 888-994-7636, unifiedbrands.net

© 2012 Unified Brands. All Rights Reserved. Unified Brands is a wholly-owned subsidiary of Dover Corporation.