Page 1
PROVEN QUALITY. LEADING TECHNOLOGY.
Manual Air Spray, HVLP and Compliant guns designed for
excellent pattern, reduced maintenance and increased productivity
FINISHING
XT SERIES
Page 2
Aerospace
Auto assembly and feeder
General metal
Truck and bus
Wood finishing
▲
▲
Typical Applications
Typical Materials
Increase Performance and Productivity
The Evolution of Air Spray
DELTA SPRAY XT GUNS
Apply the finest, most consistent finish in
the industry with Graco’s Delta Spray XT
guns! They handle even the toughest of
coatings, from acids to waterbornes. With
Graco’s XT guns, you get excellent finish
quality, higher productivity, less maintenance
and downtime – every time you spray!
The XT Series Offers:
• The finest finish quality in the industry
• A consistent spray pattern
• Increased flow for higher productivity
• Fewer parts for less maintenance
and downtime
Sealants and adhesives
Epoxies
High solids
Latex
NGR stains
Primers
Solventborne coatings
Topcoats
Waterborne coatings
2K urethanes
Materials less than 500 cps
Page 3
XT Air Spray
The Most Widely-Used Finishing Technology!
• Class A or automotive finish
• Easy to use, flexible and provides
the finest finish quality
• Offers the fastest production line speed
XT Compliant
Meets European Environmental Regulations!
• A controlled air spray technology
• Offers less bounce-back and
over spray than air spray
• Lower air consumption and
higher spray rates than HVLP
XT HVLP
Meets Strict U.S. 0Environmental Regulations!
• A more controlled air spray technology
• Excellent atomization and high
transfer efficiency
• Reduces bounce-back
and over spray
XT SERIES
AIR SPRAY COMPLIANT HVLP
FINISH QUALITY Best Better Good
TRANSFER EFFICIENCY Medium High High
FLUID FLOW High Medium Low
AIR FLOW Low Low High
Page 4
Simply a Better Gun
Remove the front cap
and nozzle using a single tool
Easily remove needle
assembly
Lowest number of parts in the
industry means lower life cycle costs
Consistent Spray Pattern
• State-of-the-art fluid section provides the
best spray pattern in the industry
• Even film build aids in corrosion resistance for
metals and eliminates striping often associated
with stains
• Newly designed nozzle and air cap seating
provides accyrate centering to provide consistent
particle size and pattern density
• Strict manufacturing tolerances make it easy
to interchange nozzles and fluid tips without
sacrificing performance
Less Maintenance and Down Time
• Get longer life and do less maintenance with XT’s
hardened stainless steel nozzle and needle tip
• Dual valve design reduces the number of operating
parts for less maintenance and downtime
• Removable needle tip reduces repair costs
• No special tools required (convenient wrench included)
Higher Productivity
• Less spray overlap means parts are sprayed faster
• Compared to HVLP, Compliant guns offer similar
transfer efficiencies with higher line speeds
• Ergonomic design means operators are more
comfortable for increased productivity
• Fan pattern and fluid flow are quick and
easy to adjust
• Larger fluid intake allows for up to 300 psi
XT SERIES
SPRAY PATTERNS
TYPICAL COMPETITOR
Page 5
Designed for Superior Finish Quality!
1. State-of-the-art Fluid Section
Provides the best finish quality
in the industry
2. New Ring Design
Prevents air cap from moving
while tightening
3. Removable Needle Tip
Reduces repair costs
4. Improved Air Cap and Nozzle Seating
Maintains pattern consistency,
increases product longevity with
stainless steel construction, and
reduces inventory with common
nozzle sizes
5. More Robust Fluid Intake
Fluid intake allows up to 300 PSI
6. Dual Valve Design
Decreases the number of parts
for less maintenance, and reduces
the overall weight of the gun
7. Smooth, Curved Handle
Improves operator comfort, reduces
fatigue and makes clean up easy
8. Easy Adjustments
Quickly and easily adjust the
fan pattern and fluid flow
9. Feed Options
Choose from pressure, siphon
or gravity feed
10.Gravity Feed Cup
Reduces cleaning and labor costs
The Best Spray Pattern in the Industry!
DELTA XT
5
3
1
6
7
4
2
SPRAY ATOMIZATION COMPARISON
9
8
PRESSURE FEE D SIPHON FE E D G RAVITY FEED
10
The Delta Spray XT Series not only has the best
pattern balance in the industry, but it is also the
most consistent.
Unlike the competition, the fluid atomized
particles remain the same size from one side
of the spray pattern to the other – reducing the
need for spray overlap and delivering an
outstanding finish every time!
COMMON COMPETITOR GRACO XT SERIES
Inconsistent particle size Consistent particle size deliver
produce an uneven finish an even finish every time!
Page 6
Reduce Cleaning and Labor Costs
Save Using Graco’s Disposable Cup
NEW 3MTMPPSTMPaint Preparation System Cup
with Disposable Liner From Graco!
Reduce your cleaning solvent usage by 70% and your cleaning labor
by 80% with this new disposable cup!
• A faster system for mixing and disposal
• One cup for measuring, mixing and spraying
• Conveniently functions at any angle – even upside down
• Reduces coatings usage by increasing transfer efficiency
• Strains as you spray by incorporating a filter/screen in the lid
• Closed system provides protection from outside contamination
• Gravity and siphon uses same cup
• Locking collar prevents spills
• Available in three sizes, 6 oz, 25 oz, and 32 oz
CAN BE MOUNTED F OR
SIPHON OR GRAVITY FEED!
STANDARD C U P
3M’s PPSTMCUP from GRACO
Items Per Gun Cleaning
3MTMPPSTMLid, Strainer & Liner
$
1.50
Gun Cleaning Solvent
Cost per Ounce ($150/drum) $0.021
Ounces Used (Per Cleaning) 3 oz
Total Solvent Cost (Per Cleaning)
$
0.063
Hazardous Solvent Waste Removal
Cost per Ounce ($200/drum) $0.028
Ounces Used (Per Cleaning) 3 oz
Waste Removal Cost (Per Cleaning)
$
.085
Coating Waste
Total Waste Materials (Per Cleaning)
$
0
Total Materials Cost (Per Cleaning)
$
1.65
Labor Per Cleaning
Shop Labor Rate (Per Minute)
$
0.25
Time to Clean Gun (in Minutes) 3
Total Labor Cost (Per Cleaning)
$
0.75
Total Cost Per Gun Cleaning
$
2.40
X X
X
X
=
X
X
X
X
+
=
=
=
=
=
=
=
=
+
Items Per Gun Cleaning
Plastic Mixing Cups
$
.35
Paint Strainers
$
.05
Total Items Cost (Per Cleaning)
$
.40
Gun & Cup Cleaning Solvent
Cost per Ounce ($150/drum)
$
0.021
Ounces used (Per Cleaning) 32 oz
Total Solvent Cost (Per Cleaning)
$
0.68
Hazardous Solvent Waste Removal
Cost per Ounce
($200/drum)
$
0.028
Ounces used (Per Cleaning) 32 oz
Waste Removal Cost (Per Cleaning)
$
0.91
Coating Waste
Cost per Ounce ($45/gallon)
$
0.35
Wasted Material 1.5 oz
Total Waste Coating (Per Cleaning)
$
0.53
Total Material Cost (Per Cleaning)
$
2.52
Labor Per Cleaning
Shop Labor Rate (Per Minute)
$
0.25
Time to Clean Gun (In Minutes) 15
Total Labor Cost (Per Cleaning)
$
3.75
Total Cost Per Gun Cleaning
$
6.27
Save up to $4.12 per gun cleaning –
that’s over $2,000 per year!
Page 7
SPR AY PAC KAGES
PRESSURE POTS
Complete Systems
TRITON PUMPS
• Ideal for medium to high volume
fine finish applications
• Easy-to-use, air operated
diaphragm pump
• Lowest pulsation diaphragm
pump in the market
•
Ability to
recirculate material
• Quick to color change,
clean and refill
• Cost equivalent to 10 gallon
SST pressure tank
• Rugged stainless steel or
aluminum construction
• Light weight
PR ESS U RE POTS
• Ideal for low to high volume,
dedicated color or fine finish applications
(i.e., 1-100 gallons used daily)
• No pulsation, high quality finish
• Simple, no moving parts
Enhance Your System Performance
Quality pumps enhance any finishing system. Graco offers a
variety of pumps and packages to meet the needs of your
low to high volume applications, and to increase productivity.
Page 8
ALPHA AND ALP HA PLUS AIR-ASSIST
• Excellent transfer efficiency at high production speeds
• Small, lightweight and well-balanced for operator comfort
• Stainless steel construction for acid-catalyzed and
waterborne materials
• Alpha Plus model offers Reverse-A-Clean (RAC
®
)
tip designed to minimize tip plugging
SILVER P LUS AIRLESS
• Contoured handle reduces fatigue and
increases comfort
• No adjustment needle makes for
quick and easy repairs
• Patented needle design increases life
Guns For Every Application
SPR AY GUNS
Whatever your application, Graco has the product solution!
Choose from our complete line of spray guns and take your
finishing to the next level of performance!
PRO XS ELECTROSTATIC
• Light weight gun with excellent spraying control
• Full range of electrostatic spraying capabilities
• Air-powered gun for easy installation and service
• Up to 55% higher transfer efficiency than
conventional guns
• Waterborne available
Page 9
Accessories
239631 Air Whip Hose Assembly
Max. working pressure: 100 psi (0.7 MPa, 7 bar).
Easier gun movement with increased hose flexibility.
Length: 4 ft (1.2 m). ID: 5/16 in (7.9 mm)
Swivel: 1/4 npsm(f), nitrile
239636 15 ft (4.6 m) Air Hose Assembly
Max. working pressure: 100 psi (0.7 MPa, 7 bar).
ID: 5/16 in (7.9 mm) Swivel: 1/4 npsm(f), nitrile
239637 25 ft (7.6 m) Air Hose Assembly
Max. working pressure: 100 psi (0.7 MPa, 7 bar).
ID: 5/16 in (7.9 mm) Swivel: 1/4 npsm(f), nitrile
239622 Fluid Whip Hose Assembly
Max. working pressure: 100 psi (0.7 MPa, 7 bar).
ID: 3/16 in (4.8 mm). 3/8 npsm(fbe), nylon with
polyurethane cover
239633 15 ft (4.6 m) Fluid Hose Assembly
Max. working pressure: 100 psi (0.7 MPa, 7 bar).
ID: 3/16 in (4.8 mm). 3/8 npsm(fbe), nylon with
polyurethane cover
239634 25 ft (7.6 m) Fluid Hose Assembly
Max. working pressure: 100 psi (0.7 MPa, 7 bar).
ID: 3/16 in (4.8 mm). 3/8 npsm(fbe), nylon with
polyurethane cover
234784 Air Control Valve Kit (Cheater Valve) with Gauge
Small, lightweight unit attaches to any HVLP spray gun
for precise air pressure setting. 0-160 psi gauge.
235119 Gun Air Regulator Assembly
Air regulator 0-100 psi (0.7 MPa, 0-7 bar) to control
air pressure to the gun. Note: Installing the gun air
regulator adds a pressure drop that could limit the
air cap pressure.
239714 16 oz (474 cc) Gravity Cup Kit
For use with gravity feed gun. Nylon cup, 304
SST 3/8 npsm(f) fluid inlet fitting and fluid filter
cartridge included.
239715 8 oz (237 cc) Gravity Cup Kit
For use with gravity feed gun. Nylon cup, 304
SST 3/8 npsm(f) fluid inlet fitting and fluid filter
cartridge included.
240266 Disposable Polyethylene Cup Liners
1 qt (0.9 l) capacity, paint and solvent resistant.
Must be used with pressure and siphon cups.
40 liners per box.
192407 Gravity Cup Holder
239802 SST Pressure Cup with Single Air Regulator
1 qt (0.9 l) capacity, 304 SST cup. Includes a pressure
relief valve and a single cup air regulator and gauge.
Air Pressure Verification Kit
For use in checking air cap atomizing or fan air pressure at
various supply air pressures. Not to be used for actual praying.
Note: To be HVLP compliant, the atomizing air pressure must
not exceed 10 psi (70 MPa, 0.7 bar).
Orifice Size in inches (mm)
239609 0.030,0.042,0.055 (0.762,1.067, 1.397)
239610 0.070, 0.086, (1.778, 2.184)
239611 0.110 (2.790)
239612 Gravity
239803 SST Pressure Cup with Double Air Regulator
1 qt (0.9 l) capacity, 304 SST cup. Includes a pressure
relief valve, a 0-100 psi (0-0.7 MPa, 0-7 bar) air regulator
for gun atomization, and 0-15 psi (0-104 kPa, 0-1.0 bar)
air regulator for the 1 qt pressure cup air supply.
239804 Remote SST Pressure Cup
1 qt (0.9 l) capacity, 304 SST cup. Includes air pressure
regulator and gauge, 4 ft (1.2 m) length air and fluid
hose with 1/4 npsm(f) swivel ends, pressure relief valve
and rigid hook handle.
234828 Repair Kit
O-rings, fluid packings, u-cups and air valve
3M’s PPSTMPaint Preparation
System Accessories from Graco
6 oz (150 ml)3MTMPPS
TM
234941 Cup and Collar (box of 8)
For use with gravity and siphon feed guns.
234940 Lid and Liner (box of 50)
For use with gravity and siphon feed guns.
234942 Measurement Insert (box of 50)
25 oz (650 ml) 3MTMPPS
TM
234771 Cup and Collar (box of 8)
For use with gravity and siphon feed guns.
234772 Lid and Liner (box of 50)
For use with gravity and siphon feed guns.
15F531 Measurement Insert (box of 100)
234837 Gravity Kit (one each: cup, collar, lid, liner, adapter)
234773 Siphon Kit (one each: cup, collar, lid, liner, adapter)
32 oz (850 ml) 3MTMPPS
TM
234937 Cup and Collar (box of 4)
For use with gravity and siphon feed guns.
234938 Lid and Liner (box of 25)
For use with gravity and siphon feed guns.
234939 Measurement Insert (box of 100)
15E470 3MTMPPSTMLid Dispenser
15E469 3MTMPPSTMLiner Dispenser
15E467 3MTMPPSTMGun Tray
15D684 3MTMPPSTMSiphon Feed Adapter
15C464 3M
TM
PPSTMGravity Feed Adapter
Instruction Manual 310693
Page 10
1 Determine technology required
(Air Spray, HVLP or Compliant)
2 Determine type of feed (Pressure,
Siphon or Gravity)
3 Select material viscosity
4 Select average flow rate
5 Select optional pattern width
AIR SPRAY GUNS
Feed Material Flow Pattern Orifice Part Numbers
Type Viscosity oz/min (l/min) Width Size Assembly Air Cap
in (mm) in (mm)
Pressure light 4–12 (0.12–0.36) 15 (381) 0.030 (0.8) 234636 234757
Pressure light-medium 8–20 (0.24–0.60) 17 (432) 0.042 (1.0) 234637 234757
Pressure medium 16–30 (0.48–0.90) 17 (432) 0.055 (1.4) 234638 234757
Pressure medium-heavy 16–35 (0.48–1.05) 18 (457) 0.070 (1.8) 234639 234757
Pressure heavy 16–40 (0.48–1.20) 13 (330) 0.08 6 (2.2) 2346 4 0 234760
Pressure heavy 16–45 (0.48–1.35) 11 (279) 0.110 (2.8) 234641 234761
Pressure (hardened) light-medium 8–20 (0.24–0.60) 17 (432) 0.042 (1.1) 234644 234757
Pressure (hardened) medium 16–30 (0.48–0.90) 17 (432) 0.055 (1.4) 234645 234757
Pressure (hardened) medium–heavy 16–35 (0.48–1.05) 18 (457) 0.070 (1.8) 234 6 46 234757
Pressure spattter 8–20 (0.24–0.60) N/A 0.042 (1.1) 234788 19610 9
Siphon light 4–10 (0.12–0.30) 10 (254) 0.055 (1.4) 234642 234759
Siphon light-medium 8–12 (0.24–0.36) 10 (254) 0.070 (1.8) 234643 234759
Siphon w/cup (1 qt) light 4–10 (0.12–0.30) 10 (254) 0.055 (1.4) 234717 234759
Siphon w/cup (1 qt) light-medium 8–12 (0.24–0.36) 10 (254) 0.070 (1.8) 234718 234759
Gravity light-medium 4–10 (0.12–0.30) 9 (229) 0.055 (1.4) 234662 234759
Gravity light-medium 8–12 (0.24–0.36) 9 (229) 0.070 (1.8) 2346 63 234759
Gravity w/cup (16 oz) light-medium 4–10 (0.12–0.30) 9 (229) 0.055 (1.4) 234705 234759
Gravity w/cup (16 oz) light-medium 8–12 (0.24–0.36) 9 (229) 0.070 (1.8) 234706 234759
Gravity / PPS cup (25 oz) light-medium 4–10 (0.12–0.30) 9 (229) 0.055 (1.4) 234 677 234759
Gravity / PPS cup (25 oz) light-medium 8–12 (0.24–0.36) 9 (229) 0.070 (1.8) 234678 234759
HVLP GUNS
Feed Material Flow Pattern Orifice Part Numbers
Type Viscosity oz/min (l/min) Width Size Assembly Air Cap
in (mm) in (mm)
Pressure light 4–10 (0.12–0.30) 15 (381) 0.030 (0.8) 234647 234753
Pressure light-medium 8-14 (0.24-0.42) 16 (406) 0.0 42 (1.1) 234648 234753
Pressure medium 12-18 (0.36-0.54) 16 (406) 0.055 (1.4) 234649 234753
Pressure medium-heavy 16-20 (0.48-0.60) 17 (432) 0.070 (1.8) 234 65 0 234753
Pressure heavy 18-22 (0.54-0.66) 17 (432) 0.086 (2.2) 234 651 234754
Pressure heavy 20-24 (0.60-0.72) 18 (457) 0.110 (2.8) 234652 234755
Pressure (hardened) light-medium 8-14 (0.24-0.42) 16 (406) 0.042 (1.1) 234653 234753
Pressure (hardened) medium 12-18 (0.36-0.54) 16 (40 6) 0.055 (1.4) 234 65 4 234753
Pressure (hardened) medium–heavy 16-20 (0.48-0.60) 17 (432) 0.070 (1.8) 234 655 234753
Pressure w/cup (1 qt) light-medium 8-14 (0.24-0.42) 16 (406) 0.042 (1.1) 234709 234753
Pressure w/cup (1 qt) medium 12-18 (0.36-0.54) 16 (406) 0.055 (1.4) 234710 234753
Pressure w/cup (1 qt) medium-heavy 16-20 (0.48-0.6 0) 17 (432) 0.070 (1.8) 234711 234753
Pressure w/cup (1 qt) heavy 18-22 (0.5 4-0.6 6) 17 (432) 0.086 (2.2) 234712 234754
Gravity light-medium 3-5 (0.09-0.15) 14 (356) 0.055 (1.4) 234658 234752
Gravity light-medium 4-6 (0.12-0.18) 16 (406) 0.070 (1.8) 234659 234752
Gravity w/cup (16 oz) light-medium 3-5 (0.09-0.15) 14 (35 6) 0.055 (1.4) 234713 234752
Gravity w/cup (16 oz) light-medium 4-6 (0.12-0.18) 16 (406) 0.070 (1.8) 234714 234752
Gravity / PPS cup (25 oz) light-medium 3-5 (0.09-0.15) 14 (356) 0.055 (1.4) 234681 234752
Gravity / PPS cup (25 oz) light-medium 4-6 (0.12-0.18) 16 (4 0 6) 0.070 (1.8) 234 6 82 234752
Ordering Information
How to Order?
Page 11
COMPLIANT*
Feed Material Flow Pattern Orifice Part Numbers
Type Viscosity oz/min (l/min) Width Size Assembly Air Cap
in (mm) in (mm)
Pressure light 4–10 (0.12–0.30) 15 (381) 0.030 (0.8) 234693 234762
Pressure light-medium 8-14 (0.24-0.42) 16 (406) 0.042 (1.1) 234694 234762
Pressure medium 12-18 (0.36-0.54) 16 (406) 0.055 (1.4) 234695 234762
Pressure medium-heav y 16-20 (0.48-0.60) 17 (432) 0.070 (1.8) 2346 9 6 234762
Siphon light 4–10 (0.12–0.30) 10 (254) 0.055 (1.4) 2346 95 234762
Siphon light-medium 8–12 (0.24–0.36) 10 (254) 0.070 (1.8) 234696 234762
Siphon w/cup (1 qt) light 4–10 (0.12–0.30) 10 (254) 0.055 (1.4) 234732 234762
Siphon w/cup (1 qt) light-medium 8–12 (0.24–0.36) 10 (254) 0.070 (1.8) 234733 234762
Gravity light-medium 3-5 (0.09-0.15) 14 (356) 0.055 (1.4) 234685 234762
Gravity light-medium 4-6 (0.12-0.18) 16 (4 0 6) 0.070 (1.8) 2346 8 6 234762
Gravity w/cup (16 oz) light-medium 3-5 (0.09-0.15) 14 (356) 0.055 (1.4) 234721 234762
Gravity w/cup (16 oz) light-medium 4-6 (0.12-0.18) 16 (4 0 6) 0.070 (1.8) 234722 234762
Gravity / PPS cup (25 oz) light-medium 3-5 (0.09-0.15) 14 (356) 0.055 (1.4) 234689 234762
Gravity / PPS cup (25 oz) light-medium 4-6 (0.12-0.18) 16 (4 0 6) 0.070 (1.8) 234 69 0 234762
* Tested to EN13966
NOZZLES/NE E DLE S/N E E DLE TI P S (HVLP, AI R SPRAY & COMPLIANT)
Orifice Size Nozzle Needle A ssembly Needle Tip Needle/Nozzle Kit
0.030 (0.762) 234741 234765 234777 234829
0.042 (1.067) 234742 234765 234777 234830
0.051 (1.29 6) 234743 234767 234778 234831
0.055 (1.397) 234744 234767 234778 234832
0.059 (1.499) 234745 234767 234778 234833
0.070 (1.778) 234746 234767 234778 234834
0.086 (2.184) 234747 234769 234779 234835
0.110 (2.790) 234748 234770 234780 234836
0.042 (hardened) 234749 234766 234781 234774
0.055 (hardened) 234750 234768 234782 234775
0.070 (hardened) 234751 234768 234782 234776
0.042 (1.067) (spatter) 15E139 234765 234777 N/A
Technical Specifications
Maximum fluid pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 psi (7 bar, 0.7 MPa)
Maximum working air pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 psi (7 bar, 0.7 MPa)
Fluid and air temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32–109ºF (0–43ºC)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.3 oz
Air Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4-18 npsm (R1/4-19) compound thread
Fluid inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/8-18 npsm (R3/8-19) compound thread
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.7 in L x 7.6 in H (1700 mm L x 193 mm H)
Typical compliant inbound air pressure
HVLP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gravity/Siphon: 29 psi (2 bar, 0.2 MPa);
Pressure: 40 psi (2.8 bar, 0.3 MPa)
Compliant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 psi (2 bar)
Air consumption
Air Spray . . . . . . . . . . . . . . . . . . . Gravity/Siphon: 14.1 scfm @ 50 psi; Pressure: 12.5 scfm @ 50 psi
HVLP . . . . . . . . . . . . . . . . . . . . . . Gravity/Siphon: 15.5 scfm @ 29 psi; Pressure: 21.0 scfm @ 40 psi
Compliant . . . . . . . . . . . . . . . . . . Gravity/Siphon: 11.2 scfm @ 29 psi; Pressure: 11.2 scfm @ 29 psi
Instruction Manual
Air Spray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 310692
HVLP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 310692
Compliant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 310692
Ordering Information
Page 12
ABOUT GRACO
PROVEN QUALITY. LEADING TECHNOLOGY.
Founded in 1926, Graco is a world leader in fluid handling systems and components. Graco products
move, measure, control, dispense and apply a wide range of fluids and viscous materials used in vehicle
lubrication, commercial and industrial settings.
The company’s success is based on its unwavering commitment to technical excellence, world-class
manufacturing and unparalleled customer service. Working closely with qualified distributors, Graco
offers systems, products and technology which set the quality standard in a wide range of fluid handling
solutions. Graco provides equipment for spray finishing, protective coating, paint circulation, lubrication,
and dispensing sealants and adhesives, along with power application equipment for the contractor
industry. Graco’s ongoing investment in fluid management and control will continue to provide
innovative solutions to a diverse global market.
©2005-2004 Graco Inc. 336435 Rev. B 2/05 Printed in U.S.A.
All other brand names or marks are used for identification purposes and are trademarks of their respective owners.
Sales/Distribution/Service North America
Industrial Customer Service
800-328-0211
FAX 877-340-6427
Industrial Product Information/Demonstration
1-877-84GRACO (1-877-844-7226)
FAX 612-378-3597
Graco Inc. is registered to I.S. EN ISO 9001
GRACO HEADQUARTERS
All written and visual data contained in this document are based on the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice.
AMERICAS
MINNESOTA
Worldwide Headquarters
Graco Inc.
88-11th Avenue N.E.
Minneapolis, MN 55413
MAILING ADDRESS
P.O. Box 1441
Minneapolis, MN 55440-1441
Tel 612 623-6000
Fax 612 623-6777
EUROPE
BELGIUM
European Headquarters
Graco N.V.
Industrieterrein - Oude Bunders
Slakweidestraat 31
3630 Maasmechelen, Belgium
Tel 32 89 770 700
Fax 32 89 770 777
ASIA PACIFIC
JAPAN
Graco K.K.
1-27-12 Hayabuchi
Tsuzuki-ku
Yokohama City, Japan 2240025
Tel 81 45 593 7300
Fax 81 45 593 7301
CHINA
Graco Hong Kong Ltd.
Representative Office
Room 118 1st Floor
No. 2 Xin Yuan Building
No. 509 Cao Bao Road
Shanghai, P.R.China 200233
Tel 86 21 649 50088
Fax 86 21 649 50077
KOREA
Graco Korea Inc.
Choheung Bank Bldg, 4th Floor
#1599, Gwanyang-Dong, Dongan-Ku
Anyang-Si, Gyunggi-Do, Korea
431-060
Tel 82 31 476 9400
Fax 82 31 476 9801
GRACO INC.
P.O. Box 1441
Minneapolis, MN 55440-1441
XT SERIES
Call today for product information or to request a demonstration.
1.877 .84GRACO (1-877-844-7226) or visit us at www.graco.com.
Loading...